Construction of School of Nursing in Dr. R.P. Govt. Medical College at Tanda in Distt Kangra , (Himachal Pradesh)

Amount

Excavation in foundation, trenches etcetera. in earth work in all classification of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, shoring, strutting or bailing out water (Surface and sub soil water) upto any depth or height any quantum of water including de-watering removal of slush, lift upto any height, stacking the excavated soil clear from the edge of excavation and then retuning the stacked soil in 15cm (Fifteen centimetre) layers, when required into plinths, sides of foundation etcetera; consolidating each deposited layer by ramming, watering and then disposing of all excavated earth and as directed by the Engineer-in-charge, within all leads, lifts and other incidentals as per specifications, approved drawing, design. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material complete and as directed by the Engineer-in-charge, within all leads, lifts and other incidentals as per specifications, approved drawing, design. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Edges of slabs and breaks in floors and walls above 20cm twenty centimentre) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, entire satisfaction and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Boulder filling under floor hand packed tightly of approved quality including watering ramming, consolidating and dressing complete as per specifications, approved drawing, design as per entire satisfactions and direction of Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Earth Filling in foundation trenches as per drawing and technical specification Clause 305.3.9, (For marshy soil) as per specifications, approved drawing, design as per entire satisfactions and direction of Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetre) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Foundation footings, bases of columns and mass concrete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, entire satisfaction and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings and the like as per Architectural drawing, design and specifications including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in vertical surface such as walls (any thickness) partitions and the like including attached, pilasters, buttresses, plinth and string courses and the like including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetre), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns pillar posts and struts square rectangular or polygonal in plan including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in suspended floors, slab etc; above 200mm(Two hundred millimetres) thickness and the like as per Architectural drawing, design and specifications including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Sides and soffits of beams, beam haunchings, cantilevers, girders, bressumers and lintels including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetre), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced plain concrete work in edges of slab and breaks in floors and walls under any thickness including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the minimum compressive strength of 20N/mm2 (Twenty Newton per square millimetr) with cement contents not less than 320 Kgs (Three hundred twenty kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in walls any (thickness but not less than 0.10m) (Zero point one zero metre) individually or forming box louvers and projected band upto all floor level as per specifications approved drawing, design including carriage of materials within all heights leads, lifts and other incidentals, as per approved drawing, design and as directed by the Engineer-Incharge . The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the minimum ccompressive strength of 20N/mm2 (Twenty Newton per square millimetre) with cement contents not less than 330 Kgs (Three hundred thirty kilogram) per cubic metre to give a smooth surfaces mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in foundation, footings, bases of columns and the like mass concrete in all depths/thickness upto all floors levels as per specifications, drawing, design as per entire satisfaction and direction of Engineer-Incharge including carrige of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M-Twenty) design mix to obtain the minimum comressive strength of 20N/mm2 (Twenty Newton per square millimetre) with cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic metre, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in suspended floors, roofs, landings, shelves and their supports balconies, beams, girder, bressumers and cantilevers in all depths/thickness including mouldings, cornices etcetera; upto all floor levels as per specifications, approved drawing, design as per entire satisfaction and direction of Engineer-Incharge including carrige of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design to obtain the minimum compressive strength of 20N/mm2 (Twenty Newton per square millimetre) with mix cement contents not less than 320 Kgs (Three hundred twenty kilograms) per cubic meter mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in columns, pillars posts and struts in all depth/thickness for all floors heights as per specifications approved drawing, design including carriage of materials within all leads, lifts and other incidentals, directed by the Engineer-Incharge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the minimum compressive strength of 20N/mm2 (Twenty Newton per square millimetre) with cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in in string courses, copings, bed plates, anchor blocks, plain windows sills and the like including carriage of materials within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-Incharge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying Tor steel reinforcement of TATA/Tisco/Sail for reinforced cement concrete work including bending, binding, cutting, straightening and placing in position complete including cost of binding wires complete upto all floor levels as per specifications, approved drawing, design, as per entire satsfaction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Second class brick masonry using common burnt clay building bricks in super-structure upto any floor level in cement mortar 1:6 (One cement: Six sand) and curing complete including carriage of material within all leads, lifts and other incidentals and further as per approved specifications, drawing, design and as directed by the Engineer-Incharge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:4:8 (One cement; four sand; eight graded broken/crushed stone aggregate 40mm (Forty milimetre) nominal size) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-Incharge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 in PCC grade M-15 (M-Fifteen), including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-Incharge. The rate isinclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:3:6 (One cement : Three sand: Six graded stone aggregate 40mm (Forty millimetre) nominal size) excluding cost of centring and shuttering in foundations and plinth complete including carriage of material within all leads, lifts and other incidentals as per approved specifications drawing, design and as directed by the Engineer-Incharge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing concrete for plain/reinforced concrete in open foundations for cradle bedding complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 in PCC grade M-15 (M-Fifteen), including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-Incharge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 900mm (Nine hundred millimetre)) diameters reinforced cement concrete pipe NP2 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 (One cement: Two sand) but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1108 including carriage of material within all leads, lifts and other, incidentals as per specifications, approved drawing, design, and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying concrete for plain is reinforcement concrete in open foundation complete as per drawing and technical specification clauses 802, 803, 1202 and 1203 PCC Grade (M-20) (M-twenty) nominal mix 1:2:4 (One cement: Two sand: Four graded/crushed stone aggregate) 40mm (Forty millimetre) thickness and as per HPPWD technical specificationapproved drawing, design as per entire satisfaction and direction of Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing of road stud 100x100mm (One hundred into one hundred millimetre) die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling holes 30 mm upto a depth of 600 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS:873 (Part 4) 1973 Road Markers/Road Stud with Lens Reflecto as per specifications, approved drawing, design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge . The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Supplying fitting and placing HYSD bar reinforcement in sub-structure complete as per drawing and M.O.R.D. technical specifications clause 1002, 1005, 1010 and 1202 including cutting, bending, binding and placing in position complete in all respect including cost of binding wire upto any floor level as per specifications, approved drawing, design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing concrete for plain/reinforced concrete in super structure complete as per drawings and technical specifications Clause 802, 804, 805, 806, 807,1204 RCC garde M25 design mix as per specifications, approved drawing, design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:4:8 (One cement; four sand; eight graded crushed stone aggregate 40mm (Forty millimetre) nominal size mechanically mixed and curing complete excluding cost of form work in foundation and plinth as per specifications, approved drawing, design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Random Rubble masonry with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12(One cement: Six sand: Twelve graded crushed/broken stone aggregate 20mm(Twenty milimetre) nominal size at plinth level with cement mortar 1:6 (One cement: 6 sand) and curing complete, as per specifications, approved drawing, design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

15mm (Fifteen milimetre) thick cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering upto all floor level including arises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth with cement mortar 1:6 (One cement: Six sand) upto floor all level as per specifications, approved drawing, design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 25mm (Twenty five millimetres) thick Kota stone 600x600mm (Six hundred into Six hundred millimetre) in flooring, treads of steps and landings laid over 12mm (Twelve millimetre) thick cement mortar 1:3 (One cement : Three sand) jointed with cement slurry mixed with pigment to match the shade including semi round nosing, polishing of tiles as required complete as per specifications, approved drawing, design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 20mm (Twenty millimeters) thick granite stone in flooring laid over 20mm (Twenty millimeter) (average) thickness base of cement mortar 1:3 (One cement : Three sand) and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing polishing smi round complete as per specifications, approved drawing, design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing under layer for plinth protection of 75mm (Seventy five millimetre) thick bed of dry brick/stone aggregate 40mm (Forty milimertre) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground and carriage of material within all leads, lifts and other incidentals, as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing plinth protection 50mm (Fifty milimetre) thick with cement concrete 1:3:6 (One cement: Three sand: Six graded crushed stone aggregate 20mm (Twenty milimetre) nominal size including finishing the top surfaces of concrete smooth including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Distempering (two or more coats) with Oil bound washable distemper of Nerolac/Asian/Berger paint of required shade on undecorated wall surfaces to give an even shade and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matters and also including preparing the surface even and sand papered smooth including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Finishing wall with weather proof exterior grade emulsion of approved Nerolac/Asian/Berger paint on undecorated wall surfaces (two or more coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etcetra including sand paper smooth including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing coloured anodised aluminium work for frame of doors, windows, ventilators and glazed partitions of Jindal/Hindalco aluminium with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS:1285 anodised transparent or dyed to required shade according to IS : 1868. (Minimum anodic coating of grade AC-15) fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etcetera. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleat angle, aluminium, snap beading for glazing/panelling C.P. brass/stainless steel screws all complete as per architectural drawings specifications, design and as per the directions of Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing coloured anodised aluminium work for shutters of doors windows & ventilators shutters of Jindal/Hindalco aluminium extrusion including providing and fixing hinges/pivots and making provisions for fixing of fittings wherever required including the cost of PVC/neoprene gasket as required (fittings , glazing and panelling shall be paid for separately)with extruded built up standard tubular and other sections of approved make conforming to IS:733 and IS:1285 anodised transparent or dyed to required shade according to IS:1868. (Minimum anodic coating of grade AC-15) fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etcetera. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleat angle, aluminium, snap beading for glazing/ panelling C.P. brass/stainless steel screws all complete for shutters Jindal shall be used as per specifications, approved drawing, design as per entire satisfaction of Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 6mm (Six milliemtre) thick glass panes of glazing in aluminium door shutters and partition etc with PVC/neoprens gasket etcetera. complete as per the architectural drawings and the directions of Engineer-In-charge (cost of aluminium snap beading shall be paid in basic item.) Glazing (Modi Gaurd/Saint Gobain) with glass panes of 6.00mm (Six millimetres) thickness (weight not less than 13.75 kg/sqm (Thirteen point seventy five kilgrams per square metre) as per architectural drawings specifications, design and as per the directions of Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing glazing with glass panes of 5mm (Five millimetre) thickness of Modi gaurd/Saint Gobain (weight not less than 12.50 kg/sqm Twelve decimal five zero kilgrams) per square metre in door, window, ventilator shutters and partition etcetera. with PVC/neoprene gasket complete as per specifications, architectural drawings design and the directions of Engineer-In-charge complete entire carriage of materials within all leads, lifts and other The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing aluminium double action Hydraulic floor spring ISI marked bright finished with nut & screws etcetera complete including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing aluminium Pilot/sheel sliding door bolts anodized transparent or dyed to required colour and shade with necessary screws etcetera including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

300x16mm (Three hundred into Sixteen milimetre) nominal size

250x10mm (Two hundred fifty into Ten millimetre) nominal size

Providing and fixing 200x10mm (Two hundred into Ten millimetre) nominal size aluminium Tower bolts (Barrel type) anodized transparent or dyed to required colour and shade Pilot/sheel with necessary screws etcetera complete including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing aluminium Pilot oxidized seccolar anodized transparent or dyed to required colour and shade handles with necessary screws etcetera complete including carriage of material within all leads, lifts and other incidentals and further as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

150 mm (One hundred fifty millimetre) nominal size

100mm (One hundred twenty five millimetre) nominal size

Steel work welded in built up sections of TATA/SAIL over trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of red lead paint in trusses and trussed purlins beams, joists, channels, angles, tees flat with connecting plates or angle cleats as in main and cross beams, hips, jack rafters, purlins connect to common rafters and the like including carriage of material within all leads, lifts and other incidentals and further as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 0.60mm (Zero decimal Six Zero millimetres) thick prepainted steel sheet of TATA Durashine/Reliance/Jinda steel ISI marked (Z-120) in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyster of 10 (Ten) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks,bolts and nuts 6mm (Six millimetre) diametrewith prepainted limpet and rubber washers complete with all accessories as required including carriage of material within all leads, lifts and other incidentals and further as per specifications, approved architectural drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing ridges or hips 60 cm (Sixty centimetres) over all with 0.60mm (Zero decimal Sixty milimetre) thick prepainted steel sheet of kolar metal TATA Durashine/Reliance/Jindal steel ridges (Factory made) shall having proper Gola/Shape of steel sheet with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating plus back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted self drilling and taping iron J or L hooks, bolts and nuts 6mm (Six milimetre) diametre with prepainted G.I. limpet and bitumen washers complete with all accessories as required including carriage of material within all leads, lifts and other incidentals and further as per specifications, approved architectural drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing plain M.S. (mild steel) B.P. (Black Plain) sheet 2mm (Two millimetre) thick of Tata/Sail fixed in eaves board/ceiling/cutting soffits/ceiling including jointing with gas/electric welding in position and applying a coat of red lead primer complete (frame work is to be measured and paid for separately) including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 4mm (Four millimetre) thick E-Board (Embossed board) Ceiling of approved quality ISI Marked including fixing to base frames with screws and clamps excreta complete (frame work for base & cover fillets to be measured and paid for separately) including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing weep holes in brick masonry/stone masonry/plain reinforced concrete abutment, wing wall, return wall with 100mm diametres P.V.C. pipe extending through the full width of the structure with slope of 1(v):20(H) towards drainage face complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Back filling Granular material behind abutment, wing wall and return wall complete as per drawing & Technical Specification Clause-1204.3.8 including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Construction of embankment with approved materials obtained from borrow pits with a lift uptoany height transporting to site spreading grading to required slope and compacted to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 80mm (Eighty milimetres) thick heavy duty precast cement concrete inter locking paver blocks of NTCvibro compacted upto M-50 (M-Fifty) grade including border or kurb block grey or coloured over sub-base of concrete with 25mm (Twenty five milimetre) thick average thickness of cement mortar 1:4 (One cement : Four sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks including curing rubbing & polishing complete (Sub base of concrete floor to be paid for seprately) including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete of grade M20 design mix to obtain the minimum compressive strengh of 20N/mm2 (Twenty newton per square milimetre with cement contants not less than 320 Kg/mm3 (Three hundred twenty kilogram pe rcubic metre) in Foundation and plinth and curing complete excluding cost of form work complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

15mm (Fifteen milimetres) with cement mortar 1:5 (One Cement: Five Sand) cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor all level including arrises,internal rounded angles, chamfers or rounded angles not exceeding 80mm in girth and finished even and smooth as per approved drawing, design and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals.

Steel work of Tata/sailwelded in built up sections over trusses and framed work, including cutting, fixing, lifting, hoisting and; placing in position complete and applying a coat of red lead paint in gratings framed gaurds, bars, ladders, railing, brackets and similar work, including entire carriage of materials within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Painting two or more coats (excluding priming coat) with Nerolac/AsianBerger paint on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

SANDHIR MALHI