S. R. to Electrical work in S.P. Office (Toilet Block) at Athwalines, Surat City, Surat. (S. R. Priority - 2025-26) (Fourth Attempt)

No. In Figure In Words

1A Providing and Erecting Point wiring with 1.1 KV grade ISI marked 2 X 355.00 Point 372.00 Rupees Three Hundred Seventy Two

1.5 sq. mm copper PVC insulted FRLS wire with 1.5 sq. mm (green) Only

copper PVC insulated FRLS wire for earth continuity in FIA approved

ISI mark medium class white colour 20/25 mm dia. embossed rigid PVC

pipe/ CASSING CAPPING with PVC fitting fixed with adhesive solution

erected on Brick Wall along th continuous G.I. fish wire to draw wires

and finishing the surface to match the wall / ceiling complete with

approved make 5/6 Amp. ISI make modular type switch and

accessories mounted in 20 G. G.I. company fabricated metallic box

covered with appropriate front plate modules erected flushed with wall /

ceiling with necessary modular lamp holder / modular ceiling rose / HD

Connector (Make and model approved by EIC and matching colour with

switch accesories) as directed for Flushed wiring Light point. Cat.-

III..Length of point wiring must not increase than 10 mtr. For that

necessary switch boards and their locations must be finalised before

execution by agency otherwise payment will not be done for extra long

point. (For future extention, if required, agency has to erect one higher

size metal box and modular plate as per instruction of EIC. Cost of

blank plate shall be paid as per tender item) [Wire must be having box

packing] in existing pipe erected flushed on wall/ceiling complete cat.III

(Conductor resistance should be as per IS:8130/1984 )

1B For Secondary Light Point Cat-III 15.00 Point 84.00 Rupees Eighty Four Only

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

1C For Bell Point (Cat-III) 5.00 Point 372.00 Rupees Three Hundred Seventy Two

1D For Fan Point.(with 6A Modular type switch and Two Module hum free 130.00 Point 517.00 Rupees Five Hundred Seventeen

5/6 step EME step type Electronic fan regulator both having ISI Make ) Only

1E For separate Point (with 6 Amp. Switch and 5 pin socket both having 35.00 Point 385.00 Rupees Three Hundred Eighty Five

ISI Make) Cat-III Only

1F For Looped on switch board (with 6 Amp. Switch and 3/5 pin socket) 150.00 Point 255.00 Rupees Two Hundred Fifty Five Only

2 Providing & Erecting Plug Point wiring with 1.1 KV grade ISI marked 50.00 Point 526.00 Rupees Five Hundred Twenty Six

approved make 2 x 2.5 sq.mm copper PVC insulated FRLS wire with Only

1.5 sq.mm (green) copper PVC insulated FRLS wire for earth continuity

in FIA approved ISI mark white colour medium class 20/25 mm dia.

embossed rigid PVC pipe with PVC fitting fixed with adhesive solution

erected in brick wall/slab along with continuous G. I. fish wire to draw

wires and laid in approved manner zari for PVC pipe & boxes shall be

filled with cement mortar & finishing the surface to match the wall /

ceiling complete with 16 Amp Modular type Swich and accessories

mounted in 20 G. GI company fabricated metallic box covered with

appropriate front plate modules erected flushed with wall. (a) 16 Amp

Indicator switch & 1 No. 6/16 A universal socket white colour suitable

for 3 pin top duly both having ISI mark. (Necessary Sheet Must Be

Erected On All Box To Prevent Mortor Going In To The Box Cat.-III.

(Conductor resistance should be as per IS:8130/1984 )

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

3 Plug Point wiring with 1.1 KV grade ISI marked approved make 2 x 4.0 15.00 Point 662.00 Rupees Six Hundred Sixty Two Only

sq.mm copper PVC insulated FRLS wire with 1.5 sq.mm (green) copper

PVC insulated FRLS wire for earth continuity in FIA approved ISI mark

white colour medium class 20/25 mm dia. embossed rigid PVC pipe

with PVC fitting fixed with adhesive solution erected in brick wall/slab

along with continuous G. I. fish wire to draw wires and laid in approved

manner zari for PVC pipe & boxes shall be filled with cement mortar &

finishing the surface to match the wall / ceiling complete with 16 Amp

Modular type Swich and accessories mounted in 20 G. GI company

fabricated metallic box covered with appropriate front plate modules

erected flushed with wall. (a) 16 Amp Indicator switch & 1 No. 6/16 A

universal socket white colour suitable for 3 pin top duly both having ISI

mark. (Necessary Sheet Must Be Erected On All Box To Prevent Mortor

Going In To The Box) Cat.-III. (Conductor resistance should be as per

4A Providing and erecting Modular type accessories mounted on 20G. 95.00 Each 159.00 Rupees One Hundred Fifty Nine Only

company Fabricated Galvanised Metal box covered with appropriate

front plate modules erected flushed with wall / ceiling with : Cat-III (a)

RJ-11 Telephone Socket [A] For One Gang Cat-III

4B Modem Jack for Computer Open RJ-45 Cat-III 160.00 Each 159.00 Rupees One Hundred Fifty Nine Only

4C Blank Plate Single Cat-III 150.00 Each 25.00 Rupees Twenty Five Only

5A Providing and erecting Medium Class FIA approved and ISI mark white 100.00 Mtr. 24.00 Rupees Twenty Four Only

colour (embossed) RIGID PVC PIPES of following size complete

erected with necessary PVC fittings and Junction boxes fixed with

adhesive solution. concealed in wall / slab along with continuous fish

wire to draw mains, laid in approved manner. Zari for PVC Pipe and

Boxes shall be plastering by cement mortar and finishing the surface

to match the wall / ceiling. (a) 20 mm dia.

5B 25 mm dia. 150.00 Mtr. 33.00 Rupees Thirty Three Only

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

6A Supplying and erecting UPVC Mini trunking (PVC Casing-n-Capping) 200.00 Mtr. 22.00 Rupees Twenty Two Only

having double-locking arrangement with grooves, trunking of size not

below 12.5 mm in height as per IS with accessories of PVC/Resin

polypropylene not below 1.8 mm thick duly sealed in joint & erected on

wall / ceiling of following size .(1) 20 mm dia.

6B For 25 mm dia. 200.00 Mtr. 31.00 Rupees Thirty One Only

7A Supplying and laying UPVC cable trunking system comprising 400.00 Mtr. 187.00 Rupees One Hundred Eighty Seven

unplasticised polyvinyl, chloride rigid material with ignition free and Only

flame proof confirming BS .All necessary accessories and measuring of

following sizes.For 50 mm x 50 mm trunking

7B For 75 mm x 50 mm trunking 400.00 Mtr. 275.00 Rupees Two Hundred Seventy Five

8 Providing and erecting PVC Corrugated Flexible Conduit with required 50.00 Mtr. 21.00 Rupees Twenty One Only

nos. of coupling, PVC bushes, Check-nuts etc. complete of following

sizes. 25mm

9A Providing and erecting Mains with FRLS PVC Insulated wire ISI marked 2500.00 Mtr. 46.00 Rupees Forty Six Only

1.1 KV grade in existing ISI mark medium class 20/25/32 mm dia.

embossed rigid PVC pipe with PVC fitting fixed with adhesive solution to

be erected on/in brick wall / slab along with continuous G. I. fish wire to

draw mains laid in approved manner with plastering by cement mortar

and finishing the surface to match the wall / ceiling complete with FRLS

PVC insulated wire for earth continuity. (Approved ISI make only)

(Conductor resistance should be as per IS:8130/1984 in Exiting Pipe [a]

2 x 1.5 sq.mm. FRLS copper multi stranded conductor mains with

sq.mm. FRLS copper multi stranded conductor for earthing as per

standard colour code. (with 20 mm dia. PVC pipe) (for point wiring and

Lighting SB mains) [Wire must be having box packing.( For Lighting

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

9B 2 x 2.5 sq.mm. FRLS copper multi stranded conductor mains with 1.5 3000.00 Mtr. 62.00 Rupees Sixty Two Only

sq.mm. FRLS copper multi stranded conductor for earthing as per

standard colour code. (in Exiting 25 mm dia. PVC pipe) [Wire must be

having box packing] (Conductor resistance should be as per

IS:8130/1984 ). ( For Computer CKT )

9C 2 x 4.0 sq.mm. FRLS copper multi stranded conductor mains with 2.5 850.00 Mtr. 86.00 Rupees Eighty Six Only

sq.mm. FRLS copper multi stranded conductor for earthing as per

standard colour code. (in Exiting 25 mm dia. PVC pipe)[Wire must be

having box packing] (Conductor resistance should be as per

IS:8130/1984 ).( For AC Point CKT Extra )

9D 2 x 6.0 sq.mm. FRLS copper multi stranded conductor mains with 2.5 1000.00 Mtr. 120.00 Rupees One Hundred Twenty Only

sq.mm. FRLS copper multi stranded conductor for earthing as per

standard colour code. (in Exiting 25 mm dia. PVC pipe) (for MCBDB

mains) [Wire must be having box packing] (Conductor resistance

should be as per IS:8130/1984 ) ( For DB To Main Switch )

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

10 Providing and Erecting 2.0 mtr. long Earthing system by making 4.00 Each 7025.00 Rupees Seven Thousand Twenty Five

minimum bore of 225 mm dia. in soft soil. Suitable for doing pipe-in-pipe Only

technology earthing. Earthing electric rod must be made from Corrosion

free hot dip galvanizing pipes having following specification. (A)

Earthing Electrode: outer Pipe: - 88 mm minimum O.D., 'B ' Class ISI

mark of Reputed Brand, Inner pipe: - 42 mm minimum O.D., Pipe B

Class ISI mark reputed Brand. Terminal Size: 70 mm X 100 mm length,

Terminal should be made from inner pipe for that pipe must be pressed

and gave rectangular shape so its work as a terminal. The hot deep

galvanising must be done after above process. Galvanised thickness

must be minimum 75 micron anywhere. SS Nut bolt- 2 nos. with washer

suitable for 14 mm dia. hole must be provided at terminal. Total

minimum Weight (approx.) of earth electrode with inside conductive

material be 26 kg.

(B) Inner chemical (CCM Compound)- Resistivity- 0.2 ohm/ meter

testing as per IEC 62561-2017, Voltage drop:- less then 1 volt at no

load and dry form, Sulphur content:- less then 2 percentage

(C) Back fill Compound- Earthing compound should be capable to retain

moisture for long time. Back Filling Compound weight is 25 Kg. (D)

Chamber and cover- Earthing chamber should be size of 400 mm X

mm X 400 mm depth and Cover should be heavy duty cast iron with

required size of 300 mm X 300 mm X 4 mm thick.

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

Necessary test report must be submitted.

1. Short circuit test by ERDA/ CPRI for 25KA

2. Resistivity test of conducting material from NABL accredited lab.

3. Hot dip galvanised / zinc coating micro test from reputed laboratory.

4. General test report from OEM regarding specification of earthing.

[Make and model approved by EIC Strictly subject to item specification

only] [OEM has to submit all detail & sample for approved before

supplying]

[Water must be poured in bore before starting earthing. Earthing value

must be measured with earth tester. Agency has to bring the earth

resistance to at least 02 ohms and voltage between neutral and

Earthing upto 02 volt. Agency has to maintain earthing and its value for

one year. Earthing must be done in the presence of A.E. (GSPHCL)]

11A Providing and Erecting Mains with ISI marked, 1.5KV grade electrolyte 80.00 Mtr. 141.00 Rupees One Hundred Forty One Only

multi stranded, annealed copper conductor with heat resistant PVC

insulated conforms to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays, power switchgears,

motor starters and control wiring) with required size of copper lugs, nuts

and bolts if required.(g) One Wire 16.00 mm2

11B One Wire 10.00 mm2 (Conductor resistance should be as per 80.00 Mtr. 91.00 Rupees Ninety One Only

11C One Wire 25.00 mm2 (Conductor resistance should be as per 60.00 Mtr. 234.00 Rupees Two Hundred Thirty Four

IS:8130/1984) Only

11D One Wire 35.00 mm2 (Conductor resistance should be as per 60.00 Mtr. 298.00 Rupees Two Hundred Ninety Eight

IS:8130/1984) Only

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

11E One wire 70.00 sq. mm.(Conductor resistance should be as per 50.00 Mtr. 663.00 Rupees Six Hundred Sixty Three Only

12 Supplying and Erecting 8 W LED Lamps with following wattage capacity 30.00 Each 111.00 Rupees One Hundred Eleven Only

of 220 to 240 voltage, minimum 15000 burning hours life, 500v in built-

surge protection, Polycarbonate diffuser , mounting suitable for E14 /

E27 / B22 lamp holders, P.F greater or equal 0.5 (A) LED lamps integral

type with pc diffuser suitable LAMP holder.

13 Supplying and Erecting LED indoor fitting of approximately 4feet 60.00 Each 370.00 Rupees Three Hundred Seventy Only

long with LED of wattage 0.2W to 0.5W assemble on single

MCPCB with housing use as a heat sink shall be made from

Aluminum extrusion having enough strength (sample must be

approved by EIC) with polycarbonate diffuser with following

specification:(A) Company mark/name on the fitting. (B) Rated input

voltage and frequency: 220V to 240 VAC ; 50Hz. (C) Rated input

wattage: max. 24w (D) Rated input current : 0.2 Amp (E) Power Factor :

Min. 0.90 (F) ATHD : Max. 15 persentage (G) Rated Luminous flux: Min.

2420 lm (H) CCT: 6500K (I) CRI: Min. 80Ra

(J) Driver Efficiency: Min. 80 persentage (K) LED life span: Min.

Hrs at L70 (L) Over Voltage protection: Withstand up to 440V/AC for

Hrs. (M)Surge protection : Min. 2KV (N) IP rating: IP

(O) IK rating : IK 02 (P) Short circuit , Open circuit and Reverse Polarity

Protection must be provided (Q) Fixing clamp design and strength

should be sufficient to hold the fitting erected on wall or ceiling. (R)

3 core copper wire of appropriate size with earthing connector (Note:-

The manufacturer/ authorized Channel partner of the manufacturer

has to submit 5 yrs free replacement Guarantee for complete

Fixture) [Approval will be given strictly subject to item specification]

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

14 SITC of Indoor Commercial Recess / Surface mounted (IP20) 24 W 230.00 Each 751.00 Rupees Seven Hundred Fifty One

Cool/Warm white Color LED Down lighter office Lighting Luminaire with Only

separate potted driver with single piece pressure die cast aluminium

alloy housing with corrosion resistant powder coated finish with

PMMA/PS/Injection moulded Polycarbonate diffuser with high

brightness LED complete (only from Philips Lumileds, CREE, Nichia,

Bridgelux, Seoul & Osram) CRI greater than 80, CCT

3000K/4000K/5600K (5400 to 5800K bin). The LED's should be

mounted on back lit metal core PCB for better heat conduction and long

life of LED. The Fixture should comply all International Standarad third

party (LM 79 for complete fixture, LM80 for individual LED). The Fixture

have protection like miswiring, over voltage, over load, wrong wiring,

THD less then 15%,, P.F greater then 0.95, efficiency greater or equal

90 lm/w & driver efficiency greater 85 persentage. For 24 W fixture wide

voltage range from 160 V to 270 V, 50/60 HZ at 240V application, 4 KV

surge protection.

The fixure must have min. 2160 lumen light output. The fixture should

be provided with external separate Potted driver, latest Valid BIS

approved Luminaire and driver. The Fixture efficiency greater equal

lumens/watt only for safety and performance. (L70 at 30,000 Hrs.) The

fixture should be able to easily mount on POP / Grid false ceiling. The

Luminiare should be tested as per IP 20 and following test reports

should be submitted at the time of approval: heat resistant test, thermal

test, Ingress protection test, drop test, Photobiological report with 3 core

X 1.0 Sq.mm. flexible wire as per site requirement [Note:-The

manufacturer / authorized Channel partner of the manufacturer has to

submit 5 yrs. free replacement Guarantee for complete Fixture]

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

15 Providing and erecting max. 10 W LED battern having main housing 10.00 Each 309.00 Rupees Three Hundred Nine Only

aluminium extruded and front cover of polycarbonate. Electrically and

photomatry parameters are as under:240 V, 50 Hz. System

wattage.:10W plus 10 persentage, PFgreater or equal 0.95, system

lumens min. 1000, CCT- 3000K to 6500K, CRIgreater or equal 80, THD

less then or equal 15%, Delivery efficiency greater or equal

persentage , LM 80 certified LED, 30000 Hrs at L70, Electronic CC

driver, insulated copper wire, for internal wiring, IP20 Operating

voltage:160 to 270 V, Surge-2 KV, length of this fitting should be 2ft.

Luminaire efficacy greater then 85 lumens/watt ,LED

LED driver efficiency greater then 85 persentage

( fitting required LM-79 persentage LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED fittings.The

shown.) Tube Light with integral driver 8 Watts, Surge-2 KV, IP-20,

conventional 1 to 2 feet

16 Providing and erecting Polycarbonate body surface mounting LED Bulk 3.00 Each 780.00 Rupees Seven Hundred Eighty Only

head type 9 watt Lighting Fitting with electronic driver having THD less

then 15% ,CRI greater then 80,P.F. greater then 0.95 And lumen output

from luminaire 800lm , input voltage range 90-300VAC , 50Hz cool

white(3000 to 6500k), inbuilt driver having THD greater then 80lm/w., -

20degC to +60degC working temperature, AL frame with Beam Angle

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

17 SITC of Indoor Commercial Recess/Surface mounted (IP20) Max. 45 35.00 Each 2071.00 Rupees Two Thousand Seventy One

watt Cool White Color LED office Lighting Luminaire having size Only

(2'X2')/(4'X1') with suitable seperate metal frame with white powder

coating for installing fitting in gypsum false ceiling with extrernal

separate driver having BIS certification for installation in Gypsum ceiling

with single piece pressure die cast aluminium alloy housing/CRCA

sheet of 0.6 mm thickness with corrosion resistant powder coated finish

Polycarbonate diffuser with high brightness LED complete (only from

Philips Lumileds, CREE, Nichia, Buildglux, seoul and Osram CRI

greater then 80, CCT 3000K/4000K/5600K (Bin 5600-600k). The led's

should be mounted on Metal core based PCB for better heat conduction

and long life of LED. (LM 79 for complete fixture, LM80 for individual

LED, report must be submitted) The Fixture should have protection of

driver like over/under voltage, THD less then 10 persentage ,Fixure

must have Min LA50 Lumen light output. Fixture Efficacy should be

greater or equal 110 Lumens/watt. The fixture should be provided with

external separate driver BIS approved only for safety and performance.

(L70 at 30,000 Hrs.) The Luminiare should be tested as per IP 20 and

necessary test reports should be submitted at the time of approval.

[Note:- The manufacturer/authorized Channel partner/dealer of the

manufacturer has to submit 5 yrs. free replcement Guarantee for

complete Fixture]

18 Supplying, Installing, Testing & Commissioning of 4K LED Bollard 30.00 Each 3130.00 Rupees Three Thousand One

fittings of minimum height 600 mm and dia.100mm having Hundred Thirty Only

polycarbonate clear/milky diffuser mounted on 3mm thick aluminium

finished powder coated pipe with base plate 160x160mm with erection

by M8x75mm fastner with required RCC foundation.IP65 for 15watt

,surge-4kv- cat-III

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

19 Supplying, Installing, Testing & Commissioning of 4K 30 W LED 4.00 Each 4052.00 Rupees Four Thousand Fifty Two

Outdoor type Post top Lantern light with IP65 protection with housing Only

made of sturdy aluminium die cast housing with radiating cool surface

and milky white high quality PMMA round cover with corrosion resistant

Grey colour powder coating with high efficiency potted driver with

necessary safety precautions, 10 kv surge protection device with high

min. 3300 lumens LED with long life of 30K at L70 (L70 at 30000 hrs.),

Installation bracket as per site requirement, accessories 3C X

Sq.mm copper flexible wire upto terminal box etc. (Note:-The

manufacturer / authorised Channel partner of the manufacturer has to

submit 5 years free replcement Guarantee for complete Fixture)

20 Supplying and erecting Electronic Type Cordless Call Bell erected on 5.00 Each 248.00 Rupees Two Hundred Forty Eight

PVC/Metal board having portable bell push working on D.C. & bell on Only

230V A.C. supply with cells / battery

21 Providing, erecting, testing Ceiling Fan confirming to IS: 374/1979 130.00 Each 1929.00 Rupees One Thousand Nine Hundred

AMDT No. 1 to 6 Class-I, 50 Hz. Specification of Ceiling Fan must be as Twenty Nine Only

per below. (1) Sweep: 1200 mm, (2) Operating Voltage: 180 to 230 V,

(3) Power Factor:greater then 0.9, (4) Power Consumption: maximum

53W, (5) RPM: minimum 330, (6) Service value:min 4.3 m3/min. (7)

Class of insulation: 'B', (8) No. of heavy duty premium quality Ball

bearing: Two, (9) Total Body: Top & Bottom should be alluminium, (10)

Blade: Aluminium approx 1.1 mm thick, (11) Colour: White high grade

powder coating, (12) Canopy: Two Nos. Heavy duty, (13) Condenser:

Min. 1.5 MFD (15 persentage Tolerence) as per IS:1709-1984, (14)

Down road: up to 1.0 mtr as per site requirment, (15) Required fixing

accessories, (16) 3 core 0.75 sq.mm ISI wire as per site requirment,

(17) No vibration and noise due to mechanical parts. (18) Safety wire

provided by manufacturer with ceiling fan. (Agency has to erect safey

wire with ceiling fan and checked with EIC) (OEM has to approved

model as per tender specification and tested at ERDA)

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

22 Supplying and erecting approved make oscillating type bracket fan A.C. 8.00 Each 2509.00 Rupees Two Thousand Five Hundred

230 V. 50 cy/s 400/450 mm sweep wall mounted with height adjustment Nine Only

and rotary tilting device complete with guard, flexible Core plug top

complete erected with lead wires as directed.

23 Providing Fan clamp of 30 x 5 mm flat of required length and 10 mm 130.00 Each 98.00 Rupees Ninety Eight Only

M.S. Bolt & Nuts erected with necessary hook of 10 mm M.S. Round

24 Supplying and erecting approved make low noise Decorative exhaust 20.00 Each 1687.00 Rupees One Thousand Six Hundred

fan having size150/200 mm with 1350 RPM with round / square frame Eighty Seven Only

ABS/metalic body with Grill / inbuilt lowers.

25 Providing and erecting Switch board for modular Computer or electric 160.00 Each 1122.00 Rupees One Thousand One Hundred

apparatus consisting of following items in single board erected on 20 Twenty Two Only

G. G.I. company fabricated metallic box erected with appropriate front

plate modules erected flushed with wall as directed. 1 no. 6/16 Amp.

universal Socket, 1 no. 13 Amp. international socket, 2 nos. 16 Amp.

indicator switch, 2 nos. 6 Amp. Switch & 2 nos. 6 Amp. 5 pin Plug. For

Computer power Supply board. Cat.-III

26 SITC of specified make Cat - 6 voice /data cable to be done in prelaid 6000.00 Mtr 47.00 Rupees Forty Seven Only

PVC pipe / raceway , but without the cost of raceway or pipe ( the wire

is to be drawn from MFD/ JB to outlet point) (a) CAT - 6-Y Colour ( For

Voice Cabling ) and X -Colour(For Computer Data Cable ) .(

Molex/Avaya/Systimax/Legrand make)

27 SITC of CAT6 UTP 24AWG PATCH CORD:1M,Plug 30U' Snag less 160.00 Each 155.00 Rupees One Hundred Fifty Five Only

(Avaya / Molex / Dax make only)

28 SITC of CAT6 UTP 24AWG PATCH CORD:2M,Plug 30U' Snag less 160.00 Each 199.00 Rupees One Hundred Ninety Nine

(Avaya / Molex / Dax make only) Only

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

29 SITC of 24 x 10/100/1000BASE-T ports 4 x Gigabit RJ45/SFP Combo 6.00 Each 15247.00 Rupees Fifteen Thousand Two

ports Advanced L2 switching and security features L2 plus Static Hundred Forty Seven Only

Routing Optional “standard mode” or “surveillance mode” management

user interface. 24 Port. [Make and model approved by EIC as per

specification]

30 SITC of Patch Panel Cat 6 UTP Keystone Type- 24 Port-Fully Loaded 6.00 Each 4357.00 Rupees Four Thousand Three

(Including five year free maintenance with guarantee) (Molex / Avaya / Hundred Fifty Seven Only

Systimax / Legrand make)

31 Supply and installation of 9U steel rack for installing 4 nos. Ethernate 3.00 Each 11441.00 Rupees Eleven Thousand Four

switches/Hubs. The Rack should be fully enclosed steel housing Hundred Forty One Only

fabricated with 14 SWG sheet and powder coated with glass doors and

having wire management systems. The rate includes the Exhaust Fan,

2 nos. 4 socket and 1 switch power strip and all the wiring in the rack.

(APW president, APC, ELIXIR, Valrack make)

32 Providing and erecting Tag Box for Telephone Lines suitable for 20 3.00 Each 1355.00 Rupees One Thousand Three

Pairs Krone type complete with Krone and locking arrangements. Hundred Fifty Five Only

33 Providing and erecting Tag Box for Telephone Lines suitable for 50 3.00 Each 1730.00 Rupees One Thousand Seven

Pairs Krone type complete with Krone and locking arrangements. Hundred Thirty Only

34 Supplying and erecting approved make Telephone Cable electrolytic 150.00 MTR 65.00 Rupees Sixty Five Only

copper conductor PE insulation twisted in two pairs, and wrapped with

FRLS PVC tape and sheathed with FRLS PVC or HFFR outer Jacket

suitable for telephone wiring and confirming to C-DOT erected in

existing pipe. of following size of conductors and nos.of pairs. With

necessary connections.(a) Unarmoured [A] Conductor Size 0.5 mm (5)

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

35 Supplying and erecting approved make Telephone Cable electrolytic 150.00 MTR 126.00 Rupees One Hundred Twenty Six

copper conductor PE insulation twisted in two pairs, and wrapped with Only

FRLS PVC tape and sheathed with FRLS PVC or HFFR outer Jacket

suitable for telephone wiring and confirming to C-DOT erected in

existing pipe. of following size of conductors and nos.of pairs. With

necessary connections.(a) Unarmoured [A] Conductor Size 0.5 mm (6)

Twenty Pairs

36 Providing and erecting approved make single phase Double Door metal clad 22.00 Each 5869.00 Rupees Five Thousand Eight

D.B. as per relevant indian standards ammended upto date. Supplying and Hundred Sixty Nine Only

fixing following way single phase MCB distrubution board of company fabricated

with sheet box with powder coated inside and outside after apply seven tank

chemical process of CRCA sheet (MCBDB Door, Backside and Body must be

made of 1.2 mm thick CRCA sheet )cover complete with suitable integral single

piece construction tinned copper busbar and link with all necessary

interconnection and with necessary size MS frame for mounting MCBDB.

Manufacturer must be provided (1) IP 43 and as per IS:8623-1 and 3, IEC

61439-1 and 3 having D type PU gasket. (2) Seven tank Powder coating

Certificate (3) Tinned Copper/Brass make neutral and Earthing link with

isolation and Protecting Cover for 240 Volts on surface / recess complete with

loose wire box, terminal connectors for all incoming and outging circuits, with

suitable size FRLS PVC insulated copper conductor up to terminal blocks and

internal connection, tinned coppper bus bar, 1 no. tinned copper neutral link,

tinned copper earth bar, din bar, detachable gland plate, interconnections,

powder painted including earthing etc. Single phase incoming and horizontal

single phase outgoing. For 16 Way MCBDB: Including 40 Amp. 30 mA double

pole ELCB (ELCB confirming to IS:12640/1988 having sensitivity of 30 mA and

breaking capacity of 10 KA), MCB 40 Amp. double pole switch (C curve

confirms to IS:8828 having breaking capacity of 10 KA) and S.P. MCB of rating

6 to 32 Amp 12 Nos. with NL suitable to operate on 240 Volt A.C. power. (6/25

(The DBs should be used of same company of MCB / ELCB to be used)

(MCBDB must be erected in line and level with spirit level and finish the external

edge with box cutting plaster) (Same colour MCB(SP/DP) should be used as

same as MCBDB) [Including Necessary numbering / marking on box done with

red colour radium sticker as per site requirement and instructions given by EIC

on site. Font / number size given by EIC on site as per requirement]

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

37 Providing and erecting weather proof, dust and vermin proof, floor 3.00 Sq.Mtr 16230.00 Rupees Sixteen Thousand Two

mounted front operated indoor type cubical panel board having IP42 Hundred Thirty Only

and above protection as per require made from 2 mm. thick CRCA M.S.

sheet for outer body and doors, 1.5 mm. thick CRCA M.S. sheet for

internal partitions with necessary supporting angles, flats including

skirting, bending, drilling, welding, riveting with internal partitions and

cable alley as per requirements and instruction of engineer-In-Charge

with erection of supplied switchgears, busbars with suitable size of

interconnecting PVC copper wire / Copper-Aluminium strips, rubber

gromets, rib, control wires, backelite control fuses, measuring

instruments, earth bus and earth bolts, foundation flange-bolts-base

plates, sufficient nos. of hinged doors, handle with locking arrangement,

rubber gasket complete with Required Nos. heavy Duty Connector.

heavy duty end terminal connection,danger notice board,necessary

ventilation,earthing strip complete.The panel shall be supplied with

Seven Tank chemical process which shall be carried out before

applying painting, painted with powder coating. (The rates excludes the

cost of switchgears, busbars, interconnecting mains and Copper /

Aluminium strip, fuse, meters etc. The dimension shall be measured

excluding base beams) Factory inspection for verification of

quality,workmanship and as per drawing and testing before dispatch the

material as per tender condition. The standard companies switch gear

shall be used and only manufacturers at CPRI approved factory as per

IEC 61439 and shall be certified by that company whose switch gears

are used after fabrication for beneficial use. With 350 mm depth

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

Panel manufacturer have to give 3 years maintenance and service

support if in case of breakdown or fault. Panel manufacturer have to

submit electrical meter calibration report. Agency should design the

panel in such a way that there should not be any excess in panel area

(sq.mtr) and length of bus bar (mtr), if any excess occurs draw attention

to GSPHCL at the time of approval of G.A. drawing. Loading and

unloading of above item shall be done by hydra and skill work force

under supervision of electrical engineer and guidelines given by

manufacturer to avoid damage to the item. Picture of it to be submitted

in running bill / final bill.

Size of door and Ele. room / Pump room shall be checked by agency's

engineer before giving order. If found any problem in size discuss with

GSPHCL engineer for rectification before giving order. [Including

Necessary numbering / marking on PANEL done with red colour radium

sticker as per site requirement and instructions given by EIC on site.

Font / number size given by EIC on site as per requirement]

38A Supplying and erecting tripple pole and neutral 440V / 500 V Panel 2.00 Rn. mtr. 1942.00 Rupees One Thousand Nine Hundred

mounting Copper Busbars with four equal Nos. of electrolyte bus having Forty Two Only

current density not more than 1.6 Amp. / sq.mm (Rated current / cross

section area) duly wraped with colour insulating tape for phase

sequence of following current carrying capacity, erected with necessary

bus bar supports / insulators, main cable socket to each bar, erected in

existing cubical panel with necessary connections. For electrolyte

copper busbars suitable for 100 Amp. capacity

38B Suitable for 300 Amp. capacity 2.00 Rn. mtr. 4861.00 Rupees Four Thousand Eight

Hundred Sixty One Only

39 Supplying and erecting approved make Four Pole 415 V change over 1.00 Each 12120.00 Rupees Twelve Thousand One

switch interior for panel mounting with operating mechanism A.C.23 Hundred Twenty Only

duty confirming to I.S.S. for 200 Amp.

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

40 Supplying and Erecting Approved make Four pole moulded case circuit 1.00 Each 16061.00 Rupees Sixteen Thousand Sixty One

breaker having breaking capacity ICU of 35 K.A. at 415 V. having Only

normal current rating 200 A. with Variable thermal & magnetic release

suitable to work on A.C.supply 50 c/s. with all internal connections

spreader tinned copper & complete erected in existing 16 G.M.S.

housing. housing. ICS equal 100 persentage of ICU only.

41 Supplying and Erecting Approved make Four pole moulded case circuit 4.00 Each 6112.00 Rupees Six Thousand One Hundred

breaker having breaking capacity ICU of 25 K.A. at 415 V, having Twelve Only

normal current rating 25 A to 100 A. with Fixed thermal & magnetic

release suitable to work on A.C. supply 50 c/s. with all internal

connections spreader tinned copper & complete erected in existing

G.M.S. housing. ICS equal 100 persentage of ICU only.

42 Providing and Erecting Extended operating rotary handle with pad lock 2.00 Each 865.00 Rupees Eight Hundred Sixty Five

with three position trip,off,on suitable for 25A to 250 A panel mounting ( Only

company must be same as switchgher company).

43 Supplying and erecting Approved make Earth fault Relay suitable to 1.00 Each 4934.00 Rupees Four Thousand Nine Hundred

mount with inter connection to moulded case circuit breaker having CT Thirty Four Only

ratio & MCCB rating as following along with shunt trip 220 V AC with all

internal connections and complete erected in existing M.S.housing (2)

125 - 200 Amp., CT Ratio 1/200 [make and model approved by EIC

strictly as per tender specification]

44 Supplying and erecting approved make panel mounting type Digital 1.00 Each 1263.00 Rupees One Thousand Two Hundred

Voltmeter having 3 x 1/2 digits LED display, 0 to 750 AC Volts range Sixty Three Only

having 0.5 class accuracy erected on existing panel board with all

connection, wiring etc. with manufacturers calibration certificate.

45 Supplying and erecting approved make panel mounting type Digital 1.00 Each 1543.00 Rupees One Thousand Five Hundred

Ammeter having 3 digits LED display, external CT operated, calibrated Forty Three Only

for 0 to 1000 Amps. suitable to operate on 500 Volt AC having 0.5 class

accuracy erected on existing panel board with all connection, wiring

etc. with manufacturers calibration certificate.

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

AC Supply 500 V on existing panel board with necessary connections. Only

47 Supplying and erecting approved make set of indicator lamps of LED 3.00 Each 43.00 Rupees Forty Three Only

type lamp, lense cover, Bakelite holder complete erected with

necessary connections.

48 Providing and erecting L.T. Current Transformer with bar primary 50/5 3.00 Each 272.00 Rupees Two Hundred Seventy Two

to 1000/5 ratio 15 VA burden erected in existing CRCA box duly Only

secured with insulating materials connected to the meter 0.50 Class

49 Providing and erecting 240 V MCB Double pole switch for Motor & 24.00 Each 327.00 Rupees Three Hundred Twenty

Inductive Load (c curve) having 10 KA breaking capacity and confirms Seven Only

to IS:8828 in Existing M.S. box having following capacity. For 40 Amp.

50A Providing and erecting 415 V MCB Four Pole for Motor & Inductive 2.00 Each 730.00 Rupees Seven Hundred Thirty Only

Load (C Curve) having 10KA breaking capacity and confirms to IS

:8828 in existing box having following capacity [c] 63 Amp.

50B For 40 Amp. FP MCB 2.00 Each 662.00 Rupees Six Hundred Sixty Two Only

51 Providing & erecting XLPE (IS : 7098) (I)-88 ISI marked armoured 400.00 Mtr 361.00 Rupees Three Hundred Sixty One

Copper cable for 1100 volt to be laid 90 cms. Under ground or to be laid Only

on wall with suitable G.I. heavy guage 1.0mm thick cable clamp or in

existing DWC pipe underground or road crossing or floor. (a) For

core x 4 sq.mm.

52 Providing and fixing Double compressed heavy duty flange type brass 20.00 Each 43.00 Rupees Forty Three Only

cable gland with rubber ring for P V C insulated armoured cable

complete with outgoing tails, insulating tape etc. For following size

cables. For 2 to 4 core x 4.0 Sq. mm (Sigma, MCI, Comet, HMI Make

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

53 Providing and fixing Solderless crimping type Copper lugs conforming to 80.00 Each 8.00 Rupees Eight Only

IS suitable for cable of following size evenly crimped with high pressure

tool & connected to switchgear terminals with brass/cadmium plated nut

bolts in an approved manner. [a] 1.5/2.5 to 6 Sq.mm

54 Providing and laying HDPE Double walled corrugated pipes (DWC) 350.00 Mtr. 117.00 Rupees One Hundred Seventeen

(conforming to IS: 16205 (part 24) 2018)) with minimum load required of Only

450N capacity with anti rodent and ultra violet material properties with

necessary connecting accessories of same material at required depth

to be laid 90 cms. under ground for laying of cable below ground / road

surface for enclosing cable and back filling the same to make ground as

per original. (A) For Outer dia. 50 mm and Inner dia. 38 mm. (Test

Certificate to be Submitted)

55 Supplying and erecting approved make Octagonal pole made from HR 10.00 Each 6917.00 Rupees Six Thousand Nine Hundred

sheet steel. The pole should be made as per IS. and shall be coated Seventeen Only

with hot dip galvanizing as per IS 2629/2633/4759, suitable suspend

local wind speed with integral Junction box with Hot Deep Galvanised

door having 2 nos. 180° operated hinges and 2 nos. Ln key locking with

silicon rubber gasket. Consist of terminal plate of min 6mm Hylam

sheet, standard profile 35 mm X 7.5 mm Din-Rail and MCB, Brass stud

type terminal and arrangement for cable termination to be erected on

RCC foundation as per details given by manufacturer and EIC

considering site requirement.

Foundation Details: (1) Grade of RCC 1:2:4, (2) Grade of steel

rainforcement of RCC FE 415, (3) Clear cover to rainforcement 50mm,

(4) Concrete vibrated, (5) use suttering / farma, (6) Hot deep galvanized

average 70 Micron, (7) Detail drawing will be given by corporation (C)

Mtr. Long 70 mm Top X 130 mm bottom dia, 3 mm thickness with

mm X 200 mm X 12 mm base plate, 4-M16 Bolts and 600 mm long hot

deep galvanized J-Bolt, nuts, washers with 800 mm under ground and

200 mm above ground level and Foundation in 1:2:4 proportion as per

details given by manufacturer and EIC considering site requirement.

Approx Pole weight 46 kg. ( RR Ispat, Bajaj, Transrail, Ambica,

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

56 Providing and Fixing of wall and terrace bracket consisting of ISI mark 10.00 Each 487.00 Rupees Four Hundred Eighty Seven

"B" class G.I. Pipe 4.2 cm outside diameter and length suitable for Only

building face for fixing the brackets and having spread of Upto

mtr. length with suitable degree angle as per site situation suggested by

EIC. vertical plane and suitable welded stiffner reducer and nipple with

check nut complete painted with one coat of red oxide and two coats of

alluminium paint with . complete with 150*150*2mm thick G.I plate with

4no heavy duty galvanized jasti khila of required size or Single arm

bracket (pipe in pipe type) suitable for terrace as per design given by

EIC Considering parfait, height ,width and total height of building and

type of led fitting (a) For single arm bracket. (Jindal / Asian / Tata /

Surya Prakash make Only) (Fabricators:- Impression / Fab / Bajaj /

Impression equipment Only) (Test certificate to be submitted) ( For

Wall Mounted Fitting-Bracket )

57 Supplying and erecting street light pole bracket bracket consisting of 10.00 Each 487.00 Rupees Four Hundred Eighty Seven

ISI mark "B" class G.I. Pipe 4.2 cm outside diameter complete with Only

suitable B class G.I. Sleeve tubing of 2 mm. thick and required size and

approx. 45 Cms length suitable for 76.5 / 80 mm. required size of pole

top having nuts and bolts for fixing the brackets and having spread of

Upto 0.7 mtr. length with 110 deg. with vertical plane and suitable

welded stiffner reducer and nipple with check nut complete painted with

one coat of red oxide and two coats of alluminium paint. or Single arm

bracket suitable for terrace as per design given by EIC (b) Single Arm

bracket. (Jindal / Asian / Tata / Surya Prakash make Only) (Fabricators:-

Impression / Fab / Bajaj / Impression equipment Only) (Test certificate

to be submitted) ( For Street Light Pole Fitting-Bracket )

58A Supplying & erecting approved make SMC press moulded composite 10.00 Each 890.00 Rupees Eight Hundred Ninety Only

FRP. loop-in, loop-out approx. 2mm thick box complete with Bakelite

connector strip 5way(3P+N+E),DIN rail for mounting mob & hinged

doors as per requirement having locking arrangements with mounting

clamp with nuts, bolts & washers suitable for erection on pole with cable

clamps& earth bolt of following size of box..For (A) 300mm x 200mm x

100mm [deep]

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

58B (D) 140 x 140 x 100mm [deep] 4.00 Each 295.00 Rupees Two Hundred Ninety Five

59 SITC of Outdoor aesthetically designed LED Street Light Luminaire with 10.00 Each 3512.00 Rupees Three Thousand Five

total consumption of Max. 45 W with single piece die cast aluminium Hundred Twelve Only

housing, high power LED shall be mounted on high quality metal core

PCB with extremely precison designed heat sink complete with IP66

protection Class with polycarbonate / thoughened glass cover the fixture

should be suitable for pole/bracket mounting. The fixture to comply both

LM79 and LM 80 guidelines with LED module min. 130 lumen/watt with

toughen Glass L70 at 50,000 hrs, provided with high quality

polycarbonate lenses for better light distribution. The Fixture Should be

able to be Pole Mounted and also bracket mounted, provided with high

quality driver for protection against high and low Voltage cut Off,

opertional for high amibient and high humid envirnoments, THD of

driver should be less than 10 persentage and P.F greater than 0.95.

Also the Fixture should meet the following technical criterias Oprating

range Voltage 160 to 270 V, system efficiency greater or equal

lm/w, and total lumens not less then 4950, CCT greater 5000K, CRI

greater 65, beam angle 120 deg, 4kV integral and non integral surge

immunity level at least 10 KV.The Separate Potted driver should have

over current, over voltage protection, short circuit protection so that the

fixture recovers once the fault is removed. In addition to the above

product should be operational in the temperature range of 0 deg to

deg and humidity range of 10 persentage to 90 persentage RH.(Note:-

The manufacturer/authorized Channel partner of the manufacturer has

to submit 5 yrs free replcement Guarantee for complete Fixture)

60 Providing and Erecting Flexible PVC insulated multistrand multicore 1.1 150.00 Mtr. 46.00 Rupees Forty Six Only

kv grade ISI marked copper wires of following size to be erected as

directed. 3 core 1.5 sq.mm. PVC insulated round copper wire ISI mark.

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

61 Providing and Erecting Flexible PVC insulated multistrand multicore 1.1 100.00 Mtr. 77.00 Rupees Seventy Seven Only

kv grade ISI marked copper wires of following size to be erected as

directed. 3 core 2.5 sq.mm. PVC insulated round copper wire ISI mark.

62 Providing and fixing of ABC Type Store Pressure Fire Extinguisher 12.00 Each 1991.00 Rupees One Thousand Nine Hundred

Having capacity 6 kg Filled with Mono Ammonium Phosphate Powder Ninety One Only

50 persentage confirms to IS 4308, Stored Pressure Type, UGTS

Pressure Gauge, Can Height 530 mm, Diameter 150 ± 10mm,

Discharge Time 24 Sec, Controllable discharge mechanism, Jet Range

5 Meters, Average Discharge is 92 persentage, applicable on Class A,B

and C and electrically started Fire, Fire Rating 4A:144B, Can

Construction : Deep drawn and CO2 Mig welded, EPDM(Ethylene

Propylene Diene Monomer) Rubber Hose with both end Aluminum

clamped, Internal Coating - Epoxy Powder coating, External Coating -

Pure Polyester Powder coating (UV Resistant),Brass forged CE Marked

valves with NRV and Auto Safety Release with safety Pin is of SS

material, Made up from 1.6mm thick sheet, Extinguishers confirmed to

IS 15683:2018 and ISI marked. Referance Weight:-Gross Weight

Kg, Empty Weight 2.9 Kg, 1. Necessary certificate and and guarantee

must be attached, 2. OEM has to provide wall mounting heavy duty

bracket/clamp, screw, hardware for installation. 3.Following printed

marking Manufacturing Date and Expiry Date must be mention on

Extinguisher 4. Refilling period must be of 3 Years. Following Printed

marking on equipment must be required:- Model No, Capacity, Gross

Weight, Content, Fire Rating, Batch No, Serial no, Mfg Month, Refilling

Due. [with necessary numbering / marking with oil paint by painter as

instructions given by G.S.P.H.C.L engineer] (Make: KANEX,

MINIMAX,CEASEFIRE)

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

63 Providing and fixing of CO2 type High Pressure Portable 4.5 kg Fire 12.00 Each 6526.00 Rupees Six Thousand Five Hundred

Extinguisher, filled with Co2 Gas as per IS 15222, Control discharge Twenty Six Only

mechanism fitted with 1 Meter Wire Braided Hose & Electrical non-

conductor Polyethylene Flat Horn with Diffuser Nozzle for dispersed

discharge of CO2, Discharge Time 12 Sec, Average Discharge is

persentage, Applicable on Class B, C and electrically started Fire, Fire

Rating 55B, Internal coating is not applicable and External coating is of

enamel spray painting, Powder Coated Handle, Valve Confirm to IS

3224 ISI Marked, CO2 Cylinder construction: hot spinning by seamless

pipes and bearing ISI mark, Body confirms to IS 7285 and PESO (

Petroleum and Explosives Safety Organization) APPROVED, Minimum

Wall Thickness 4 to 4.2 mm, Extinguishers confirmed to IS 15683:2018

and ISI marked. Referance Weight:-Gross Weight 16.4, empty weight

11.9 Kg, 1. Necessary certificate and guarantee must be attached,

OEM has to provide wall mounting heavy duty bracket/clamp, screw,

hardware for installation. 3.Following printed marking Manufacturing

Date and Expiry Date must be mention on Extinguisher 4. Refilling

period must be of 5 Years. Following Printed marking on equipment

must be required:- Model No, Capacity, Gross Weight, Content, Fire

Rating, Batch No, Serial no, Mfg Month, Refilling Due. [with necessary

numbering / marking with oil paint by painter as instructions given by

G.S.P.H.C.L engineer] (Make: KANEX, MINIMAX,CEASEFIRE)

64 Providing, erecting, fabricating the M.S. structure as per requirement of 100.00 kg 75.11 Rupees Seventy Five And Paise

site as per structure design Including proper size approved by EIC of Eleven Only

M.S. angles, flats, bars, square pipe, channels, sections (Tata, Jindal,

Asian, JSI Make) complete with cutting, welding, grinding and finishing

duly painted with Asian/Nerolac make premium quality oil paint and true

care red oxide metal primer,asian paint make with erection on site as

per direction of engineer in charge with necessary grouting cementing,

plastering and finishing complete. All hole opening of square pipe end

must be closed with M.S plate welding. Payment will be done on KG as

per Actual weight.

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

65 Dismantling the existing switchgears, DB and Busbar of any size 20.00 Each 7.00 Rupees Seven Only

complete with / without board or angle iron frame.

66 Dismantling the existing any type of indoor light fittings. 500.00 Each 5.00 Rupees Five Only

67 Dismantling the existing light, fan, bell, , independent plug point, wiring 15000.00 Point 1.00 Rupee One Only

with mains of all types along with accessories etc. complete and handed

over to dept.

68 Dismantling the existing cables of all types and sizes. 1000.00 Mtr. 6.00 Rupees Six Only

Signature of Contractor Executive Engineer (Ele)

GSPHCL Gandhinagar