REPAIR TO PLASTER ROOF TREATMENT FLOORING ETC AT 105 AD REGT AND 953 WKSP UNDER AGE BR WEST AT GE DEHU ROAD

Amount

Dismantling plain or corrugated steel sheeting any gauge, any thickness including Nainital or similar pattern roof covering , in wall clading and velley gutters complete all as specified and directed.

Dismantling of boarding, any description and fixed in any position with nails complete all as specified and directed.

Dismantling of wrought iron or mild steel work any description and fixed in any position complete all as specified and directed.

Dismantling wall & ceilling boards(fibre pulp insulation etc) or insulation boards/ slabs/blankets, any thickness including cover fillets complete all as specified and as directed.

M&L rolled sections as in main and cross beams, hip rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed witjh angle cleats or other connecting plates Fe 410 W (gde E 250 ) quality complete all as specified and as directed.

S & F 0.50mm thick pre-painted/coloured galvalume aluminium zinc coating GI based corrugated steel sheet of any colour in roofing having tensile strength 550 Mpa fixed with self tapping screws all as specifed and as directed.

All as per item No. 6 above but plain sheet fix in valley gutter / ridge complete all as specified and as directed.

S & F 12mm thick Gypsum board for ceiling, insulation and accoustic purpose 60x60cm in size fixed with screws with staples incl aluminium snap grid frame work 605x605 mm in flat/slopting ceiling with aluminium anodised grid work 35.60x23.60x1.60mm main Tee 23.60x23.60x1.60mm cross section and 26x26x1.60mm angle including 3mm dia GI wire suspender of suitable length aluminium cleats etc complete all as specified and directed.

Taking out existing water proofing treatment including cement plaster(any no of layers) on roof surfaces, cleaning the surfaces and removing the debris outside MOD land complete all as specified and as directed and cleaning the plastered / concrete surfaces with wire brushes and applying water proofing treatment as under :- (a) 15 mm thick cement plaster in 1:4 on concrete surfaces finished even & smooth without using extra cement complete. (b) Apply one coat of oil bituminous primer @ 0.20 kg/Sqm over concrete surface. (c) Laying APP Polimerised modfied membrane not less than 3 mm thick and weighing not less than 3.5 kg per Sqm by torch applicaton method. (d) The overlap for APP membrane shall be 75 mm on longitudinal direction and 100 mm on transverse direction. (e) Finally applying a coat of solar reflective bitumiious aluminium paint @ 0.15 Kg/Sqm over the membrane all as specified and directed by Engineer-in-Charge. (f) The make / treatment shall be from the one of the following manufacturer :- (i) 'Moply FP' of M/s Texsa (I) Pvt Ltd. (ii) 'Hyperplast' pf IWL India Ltd. (iii) 'Super thermpay' manufactured by M/s Shalimar tar product. (iv) 'Hydroflame' of M/s Hydrotech Ltd.

Disconnecting existing U/S PVC water tanks of capacity 500 litres, setting aside (or lowering if required) for replacement complete all as specified and as directed.

S & F rotational moulded polyethylene double layer water tanks (vertical cylindrical with close top) as per IS 12701: 1996 of 500 litres capacity hoisted and fixed in position including provision of 20 mm /15 mm dia medium grade GI pipe spouts for connecting inlet, outlet, over flow and washout pipes all as specified and as directed. MAKE :- SINTEX, ASISH PLAST with ISI MARKED

Taking up or down steel tubing and connections including cleaning for refixing of 15 mm bore of pipe complete all as specified and as directed.

Taking up or down steel tubing and connections including cleaning for refixing of 20 mm bore of pipe complete all as specified and as directed.

M & L for 15 mm bore GI pipe medium grade with all fittings and fixtures and fixed to wall, ceiling, floor complete all as specified and as directed.

M & L for 20 mm bore GI pipe medium grade with all fittings and fixtures and fixed to wall, ceiling, floor complete all as specified and as directed.

S & F in repairs ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore and fixed (minimum weight 210 gms ) complete all as specified and as directed.

S & F in repairs 15 mm dia stop valves cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or union fixed in repair for 15 mm dia GI pipe all as specified and as directed.

S&F in repairs 15 mm dia bib taps cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass furrule and fixed for 15mm dia pipe complete all as specified and as directed.

S & F in repairs 15 mm dia pillar taps fancy type cromium plated with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed for 15 mm dia pipe complete all as specified and as directed.

S & F in repairs 15 mm dia Brass cromium plated shower rose of 125 mm long leg complete all as specified and as directed.

S&F in repairsGrating round 100 mm size of PTMT (Minimum weight 25gms.) complete all as specified and as directed.

S/F in repairs Vitreous china wash basin white flat back size 550 x 400mm including , waste pipe and plug and porcelain stopper and brackets incl cutting for and pinning in ends of brackets or erecting stand along with 32mm dia CP waste coupling and PVC waste pipe of required length complete all as directed by Engineer-in-Charge.

S& F in repairs stainless steel Sinks for kitchen or laboratory with plugs, washers and wastes; including beding in cement mortar overall size 495mm x 420 mm bowl size 410 mm x 330 mm x 160 mm complete including fixing cantilever brackets and connecting union to waste pipe and coupling complete all as specified and as directed.

S & F in repairs for PVC connection pipe 15mm dia with PTMT nuts of length 450mm complete all as specified and as directed.

S&F as in repairs PVC low/high level flushing cristern white 10 litre capacity incl PVC inlet pipe with brass check low level full both sides alongwith PVC flush pipe 32mm dia jointed to WC and handle incl brackets all as directed.

S&F vitreous china squatting pan ORRISA PATTERN size 580x440mm white with integral foot rests excluding flushing cistern & fush pipe fixed in repairs complete all as specified and as directed.

Dismantling / taking down AC waste/vent pipes fixed to walls with all fittings/ accessories 100 mm dia pipes all as specified and directed by Engineer-in-Charge.

S&F, PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls, or laid in trenches bore of pipe 110 mm dia complete all as specified and directed by Engineer-in-Charge.

S&F,110 mm dia PVC (SWR) bends, any radius with access door complete all as specified and directed by Engineer-in-Charge.

S&F, 110 mm dia PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), all as speicfied and directed.

M & L non skid coloured ceramic tiles 7 to 8 mm thick area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm , in floors, etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L for vitrified coloured tiles 10mm th (square/rectangular) polished area of each tile 0.36 sqm but n exc 0.42 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed.

Ditto as per item No 34 above but on skirting with 10 mm thick rendering backing coat in CM 1:4 complete all as specified and as directed.

M & L Glazed ceramic tiles in vertical surface 450mm x300x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles with and incl backing coat 10mm thick in CM 1:4 all as specified and direced.

Dismantling of stone slabs and tiles of any description or thickness in floors aprons laid and bedded and jointed in cement mortar complete all as specified and as directed.

M&L for Marble work green marble 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like 10mm thick screed bed in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with green marble shade complete all as specified and as directed.

M&L for 20-25mm thk machine cut cuddappah stone slab flooring over cement screed bed laid and jointed with grey cment slurry mixed with pigment to match the shade of the slab including grinding polishing complete laid over and including 15 mm thick screed bed or bedding in layer in cement mortar 1 :6, all as specified and as directed.

Demolition of cement concrete ( unreinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M & L for 75 mm thick cement concrete 1:3:6 Type C2 (using 40mm graded aggregates) as in plinth protection finished top surface even and smooth without using extra cement complete all as specified and as directed.

M & L for 100 mm thick Cement concrete 1:4:8 type D-2 (40 mm graded aggregate) as in hard standing complete all as specified and as directed.

M & L for Chequered cement concrete tiles of 20 cm x 20cm x 25 mm thick with grey cement and pigment,set and jointed in neat cement slurry in floors over and including 15 mm thick screed bed or bedding layers in cement mortar 1:6 complete all as specified and as directed.

M & L for 60mm thick precast concrete interlocking paver block rubber moulded any shape and size confirming to IS 15658-2006 of M-40 Grade with grey cement and pigment over and including 50 mm thick sand cushioning complete all as specified and as directed.

Taking down chowkhats or frame with shutter (without taking off shutter from the frames) & removing from site exc. 1.5 Sqm but n. exc. 4 Sqm each.

–Ditto- as item No 40 above but n.exc. 1.50 sqm each

Taking down shutter only exc 1.00 sqm but n.exc 2.00 sqm

Taking down steel window and ventilators of any size and any specification.

S&F for pressed steel door frames with one or more rebates incl necessary fixing lugs, hinges, lock strike plates of size 125 X 60mm

S&F for pressed steel door frames with one or more rebates incl necessary fixing lugs, hinges, lock strike plates of size 105 X 60mm

M/L for PCC 1:3:6 type C1 in door frame filling all as specified and directed.

S&F factory made 35 mm thick plain framed paneled shutter (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with Commercial veneered on both faces the size of rail and style as per IS-1003 ( Pt-I) kiln seasoned and Chemically pressed of 2nd class hard wood.

S & F factory made 35 mm thick glazed & skeleton shutter of 2nd class hard wood open rebated and prepared to receive gauge (divided into squares with sash bars) edges of framing plain chamfered or rounded, fitted without & fitted beads for securing glass etc, sizes of members of shutters as specified in SSR Pt-I Sec-8 clause 8.23 (a) and fitted to chowkhats complete all as specified.

S&F aluminium powder coated window sliding type (3 track) with frame size100x35x1.2mm and shutter 39.40x17.70x1.2mm with two glass shutter & one mesh shutter incl necessary jointing cleats glazing clips, rubber packing,and locking arrangement powder coated aluminium snap beading screws including 3mm plain float glass & 0.36 mm dia and 1.4 mm width of aperture, Stainless Steel wire mesh, fittings etc complete all as specified and as directed.

S & F in repairs galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.00mm fixing to steel window with nut bolt complete all as specified and directed.

S & F, Stainless Steel wire cloth ,0.36 mm nominal dia of wire and avg width of aperture 1.40 mm and fixed with tinned tacks or galv, Wire stapples complete all as specified and directed.

S & F in repair 3 mm thick sheet glass, ordinary quality and glazing with oil putty/wooden beading in square n.exc. 0.5 sqm in each pane

S&F in repairs 25 mm dia Stianless steel curtain rod with side knobs and fancy type brackets of stainless steel of 20mm dia in pair of required size all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing

S&F30mm factory made PVC solid panel door shutter 30mm thick (style) connecting of frame made out of MS tube for top and bottom rail. MS frame shall be coverd with heat moulded plain colour PVC 'C' channel having a PVC sheet strips of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail of either side and as gap insert for toprail and bottom rail panellinn of plain colour PVC to be fitted in the ms frame welded/ sealed in the stiles and rail with suitable PVC sheet and loading and jointed together with solvent cement, supplying and fixing in the frame at site all as directed by Engineer -in -charge.

S & F 150 mm size extruded aluminium alloy handles,fabricated type anodised.

S & F aluminium anodised, barrel tower bolts of extruded section and fixed, length of bolt 150mm

S & F aluminium anodised, barrel tower bolts of extruded section and fixed, length of bolt 100mm

S& F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinges pin anodised and fixed type B-12 all as specified and directed

S & F aluminium alloy , anodised , sliding door bolt with hasp , staple ( bolt type ) & fixing clips of sheet, cast or extruded section & fixing bolts & sliding bolts of extruded section or cast aluminium alloy & fixed - length of bolt 250 mm complete all as specified.

S & F 25mm thick in repairs pre-laminated particle board exterior grade prelaminated one side with deocrative choice lamination & other side balancing white lamination, fixed with screws to timber frame work incl 6mm thick teak wood lipping patti complete all as specified and directed.

S & F of 100 mm size brass hasp and staple safety type, with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed.

M&L for rendering cement plaster 10 mm thick in CM 1:6 on fair faces of brick walls finished even and smooth w/o using extra cement complete all as specified and as directed.

M&L for rendering cement plaster 15 mm thick in CM 1:4 on fair faces of brick work or conrete wall surfaces finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M & L for Preparation of newly plastered surfaces of wall and appling two coats of oil bound distemper on walls over a coat of primer on plastered surfaces complete including 3mm thick wall care putty complete all as specified and as directed.

M & L for Preparation of newly plastered surfaces of wall and appling two coats of cement base paint on walls over a coat of primer on plastered surfaces complete all as specified and as directed.

M&L for preparation for two coats of synthetic enamel paint over a coat of pink primer including preparation of new wooden surfaces of 10cm width or girth.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide

Complete removal of existing treatment from old decorated surfaces of walls prepration of surfaces and applying two coats of distemper oil emulsion over and including a coat of priming plastered complete all as specified and directed by Engineer - in - Charge.

Complete removal of existing treatment from old decorated surfaces of walls prepration of surfaces and applying two coats of cement base paint over and including a coat of priming plastered complete all as specified and directed by Engineer - in - Charge.

M&L applying one coat of white wash on old decorated surfaces of ceiling including preparation of surfaces complete all as specified & directed by Engineer-in-Charge.

M&L preparation of old painted wooden surfaces of any description not exceeding 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old painted steel surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified & directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in Suken portion exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M & L cement conrete 1:7:12 type F2 (uisng 40mm graded aggregate) as in sunkun filling complete all as specified and directed.

Providing and carrying out water proofing treatment to toilet ,sunken slabs ,wet areas etc,after proper surface prepration ,carry out cementitious ingection grouting at leakage point using Cebex 100 plasticised expanding grouting admixture ,application of polymer modified at slab wall junction using Nitoband SBR latex screed modifier cum bonding agent and application ot two coats of brushbond RFX two part acrylic polymer modified cementitious elastomeric waterproof and protective coating etc,complete including 15 mm thick cement plaster in CM 1:4 all tools and plants as per manufacturer's specification paint complete all as specified and directed.

H S TAKHI

AVS CONSTRUCTION

L.K.R.TIWARI CONSTRUCTION

tulsani associates