CA NO. GE/K-52/2025-26 - SPL REPAIR TO BLDG NO T-10 AND T-04 OF 250 FD WKSP COY AND BLDG NO T-08 OF 308 FD HOSP AT DRAS UNDER GE KARGIL

Amount

Dismantling of plain corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern or fibre translucent sheet roof coverings etc complete all as specified and directed by the Engg-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed by the Engg-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed by the Engg-in-Charge.

S&F 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc and fixed with L-type or J-type or cranked hook bolts in lieu of screw complete all as specified and directed by the Engg-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by the Engg-in-Charge.

S&F Fe-290 (Gde E--165) Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed by the Engg-in-Charge.

S&F Fe-290 (Gde E--165) Framed work as in door or gates of angle or other section with gusset plates rails, braces etc, complete, drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fiting (exclusive of steel sheeting or other convering, running rails and guides) and hanging, also fastening and fixing complete all as specified and directed by the Engg-in-Charge.

S&F MS heavy duty adjustable sliding gate roller of suitable dia welded or fixed on site complete all as specified and directed by the Engg-in-Charge.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by the Engg-in-Charge.

M&L for preparing old steel surfaces of any description over 10cm width/girth and applying one coats of synthetic enamel paint complete all as specified and directed by the Engg-in-Charge.

Demolition of Cement Concrete (unreinforced) in ground floor and paving n.exc 15cm thickness (below or above ground level) complete all as specified and directed by the Engg-in-Charge.

M&L for PCC type B-2 1:2:4 (used 40 mm graded agg) as in foundations, filling and mass concrete complete all as specified and directed by the Engg-in-Charge.

M&L for PCC type C-2 1:3:6, 75 mm thick as in plinth protection and sub base or similar works complete all as specified and directed by the Engg-in-Charge.

M&L for coloured chequered cement concrete tiles 300x300x25 mm thick, with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors including 20 mm thick screed bed in CM (1:4) complete all as specified and directed by the Engg-in-Charge.

Demolition of precast concrete articles and precast concrete block walling including all quoins, arches, pillars, etc built in cement mortar of any description not other specifically provided for complete all as specified and directed by the Engg-in-Charge.

M&L for precast cement concrete type C1 (1:3:6) (using 20mm graded crushed stone agg) block masonary with solid blocks exc 10 cm in width Set in CM 1:4, complete all as specified and directed by Engr-in-charge.

M&L for rendering 15mm thick in CM (1:4) finished even & fair without using extra cement on brick/concrete surfaces complete all as specified and directed by the Engg-in-Charge.

M&L for two coats of cement based paint on newly plastered surfaces of walls over a coat of primer including preparation of surfaces complete all as specified and directed by the Engg-in-Charge.

S&F 75mm mild steel butt hinges medium weight, cold rolled welded/ screwed complete all as specified and directed by Engr-in-Charge

Hacking out old broken glass (any thickness,size,quality or description) from wooden frames metal frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed by the Engg-in-Charge.

S&F 3mm thick glass pan ordinary quality and glazing with oil putty in square n exc 0.5 Sqm in each pane complete all as specified and directed by the Engg-in-Charge.

M&L for 25 mm thick PCC type B-1, 1:2:4 (using 20 mm graded aggregate) as in sub base of floors or similar works complete all as specified and directed by the Engg-in-Charge.

M&L for hardcore of gauage n exc 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by the Engg-in-Charge.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone agg) as in foundation, filling and mass concrete complete all as specified and directed by the Engg-in-Charge.

Dismantiling of floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by the Engg-in-Charge.

M&L for non-skid ceramic coloured tiles 600mm x 600mm x 7-8mm thick in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm screed bed in CM 1:6, complete all as specified and directed by the Engr-in-Charge.

M&L for Non skid Ceramic coloured tiles 7 to 8mm thick area of each tiles exc 0.06 sqm but not exc 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm screed bed in CM 1:6 finished even and smooth for receive tiles complete all as specified and directed by the Engg-in-Charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/blankets, any thickness, including cover fillets complete all as specified and directed by the Engg-in-Charge.

S&F 12mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with nails on wall to timber frame work complete all as specified and directed by the Engg-in-Charge.

S&F 9mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with nails on ceiling to timber frame work complete all as specified and directed by the Engg-in-Charge.

Dismantling timber scantlings as in fillets, rails, posts, rafters, purlins, etc under 40 Sqcm in framed work, in any position complete all as specified and directed by the Engg-in-Charge.

M&L for Plain fillets of second class soft wood (KAIL), sectional area exceeding 13 Sqcm but not exceeding 25 Sqcm in square, rectangular or traingular in section, clean sawn secured with nails or brads complete all as specified and directed

M&L for Plain fillets of second class soft wood (KAIL), sectional area exceeding 3 Sqcm but not exceeding 6 Sqcm in square, rectangular or traingular in section, bullnosed, splayed, chamfered or rounded on one edge or face complete all as specified and directed by the Engg-in-Charge.

M&L for Plain fillets of second class soft wood (KAIL), sectional area not exceeding 3 Sqcm in square, rectangular or traingular in section, bullnosed, splayed, chamfered or rounded on one edge or face complete all as specified and directed by the Engg-in-Charge.

Taking down of shutters exc 1.0 Sqm but n.exc 2.0 Sqm each complete all as specified and directed by the Engg-in-Charge.

S&F 30mm thick 2nd class soft wood (KAIL) plain framed panelled shutter (any number of panels) with panels of timber flat on both sides (Feather edge) or of veneered particle board medium density wood particle board with commercial face veneers and fitted to chowkhat complete all as specified and directed by the Engg-in-Charge.

S&F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tacks, or galvanised wire staples including etc complete all as specified and directed by the Engg-in-Charge.

S&F 150mm long Aluminium anodised barrel tower bolt of extruded section and fixed or welded complete all as specified and directed by the Engg-in-Charge.

S&F 100mm mild steel butt hinges medium weight, cold rolled and fixed with screws or welded complete all as specified and as directed by Engr-in-Charge

S&F 125mm extruded aluminium alloy handles fabricated type anodised complete all as specified and directed by the Engg-in-Charge.

S&F 300mm Aluminium alloy, anodised,sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed by the Engg-in-Charge.

S&F in repairs mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by the Engg-in-Charge.

S&F in repair curtain rails anodised aluminium plated with fixing bracketes, stops, rollers etc complete all as specified and directed by the Engg-in-Charge.

M&L for preparation of New surface of wood and wood based material surface of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by the Engg-in-Charge.

Dismantling of PVC drain pipes of any size or any dia and any position/ description, including disposal or removing to store complete all as specified and directed by the Engg-in-Charge.

S&F PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Taking up or down 20 mm dia steel tubing/PPR connections, including cleaning for refixing or removal to store complete all as specified and directed by the Engg-in-Charge.

S&F for 20mm outer dia 3-layer PPR polypropylene random copolymer concealed pipes SDR 7.4 (PN16) UV stablized and antimivrobial fusion welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to wall, ceiling or in floors complete all as specified and directed by the Engg-in-Charge.

S&F in repairs vitreous china squatting pan, 'Orissa pattern, size 580x440mm white, with 'P' or 'S' trap including making connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe or integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and directed by the Engg-in-Charge.

S&F in repairs 10 ltrs capacity PVC valveless syphonic action type low level flushing cistern complete with syphone handle vever PVC bend including connecting to WC and fixing on walls with bracket and including P or S Trap of CI complete all as specified and directed by the Engg-in-Charge.

S&F in repairs vitreous china wash hand basin (flat back) white of size 550x400mm with pedestal including waste coupling & waste pipe and a pair of mild steel angle iron brackets of suitable size complete all as specified and directed by the Engg-in-Charge.

S&F in repair 15mm bore PVC connection 600mm long both ends screwed with brass cap complete all as specified and directed by the Engg-in-Charge.

S&F in repair 20 mm bore Pillar taps of cast copper alloy, with capstan heads, chromium plate, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nut screwed for iron pipe and fixed complete all as specified and directed by the Engg-in-Charge.

S&F in repair 20 mm dia chromium plated fancy type Bip tap with round handle screwed down for iron pipe or brass ferrule complete all as specified and directed by the Engg-in-Charge.

S&F in repair 20 mm dia chromium plated fancy type stop valves/ angle cock screwed down high pressure, screwed for iron pipe complete all as specified and directed by the Engg-in-Charge.

S&F in repair 20 dia PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and directed by the Engg-in-Charge.

M&L for PCC type C-1 (1:3:6) use 20mm graded agg 75 mm thick as in copings slightly rounded or chamfered angles and throating, complete all as specified and directed by the Engg-in-Charge.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed by the Engg-in-Charge.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m depth for foundation etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting outand getting out in hard/dense soil (for foundation or laying of UG Cables or similar works) complete all as specified and directed by Engr-in-Charge.

Removal of surplus hard/dense soil to a distance not exceeding 50m and deposting where directed at a level not exceeding and depostiting where directed at a level not exceeding 1.50m above the starting point complete all as specified and directed by the Engg-in-Charge.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

M&L for machine cut Kota stone slab flooring 20-25mm thick, over cement screed bed or bedding layer of cement mortar 20 mm thick in CM for laying floor finishes base laid and jointed with grey cement slurry mixed pigment to match the shade of the slab including rubbing and mirror polishing/ preparation complete all as specified and as directed by Engr-in-charge.

Taking down chowkats or frames exc 1.5 Sqm but n.exc 4.0 Sqm with shutters (without taking off shutters from the frames) complete all as specified and directed by the Engg-in-Charge.

Taking down chowkats or frames not exc 1.5 Sqm with shutters (without taking off shutters from the frames) complete all as specified and directed by the Engg-in-Charge.

S&F 2nd class soft wood plain, solid straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed by the Engg-in-Charge.

S&F 30 mm 2nd class softwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed by the Engg-in-Charge.

S&F 100mm long aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and directed by the Engg-in-Charge.

S&F 100mm extruded aluminium alloy handles febricated type anodised complete all as specified and directed by the Engg-in-Charge.

M&L rendering 15mm thick in CM (1:6) finished even & fair without using extra cement on brick/concrete surfaces complete all as specified and directed by the Engg-in-Charge.

M&L for preparationof new plastered surfaces on walls and applying two coats of OBD over a coat of 1mm thick putty complete all as specified and directed by the Engg-in-Charge.

Taking down carefully copper or aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches ceiling roses, pendants, sockets bulk, head fitting, tube light fitting by unscrewing carefully from boards etc and making good, distrubed surface of walls floors etc complete all as specified and directed by the Engg-in-Charge.

M&L for Point wiring for light/fan/bell with FRLS cable of 1.5sqmm PVC insulated (red/blue/yellow for phase, black for neutral and green for earth) unsheathed multistranded copper conductor 1100 volts grade in and including not less than 2mm thick PVC casing caping with all accessories and 1.5sqmm green in colour PVC insulated multistranded copper conductor FRLS cable for earth continuity connected to common earth dolly incl MS/GI sunken box with 3mm thick pre laminated hylum sheet/PVC box with back plate,flush/surface type for mounting fittings such as switches,socket,and regulator complete all as specified and directed a) for one light point or bell/buzzer point controlled by one switch.

All as per Srl item No 73.00 here in before but for one 3 pin 5 Amps switch socket on same board complete all as specified and directed by the Engg-in-Charge.

All as per Srl item No 73 here in before but using cable size 2.5 Sqmm for one 3 pin socket outlet 5 Amps independent board complete all as specified and directed by the Engg-in-Charge.

All as per Srl item No 02 here in before but using cable size 2.5 Sqmm for one 3 pin socket outlet 15 Amps independent board complete all as specified and directed by the Engg-in-Charge.

S&F in replacement of Switch piano flush type 5 Amps, single pole one way complete all as specified and directed by the Engg-in-Charge.

S&F in replacement socket outlet 2 in 1, 6 Amp flush type complete all as specified and directed by the Engg-in-Charge.

S&F in replacement of Switch socket combination 2 in 1, and 3 and 2 pin, 5 Amps flush type complete all as specified and directed by the Engg-in-Charge.

S&F in replacement of Switch socket combination 2 in 1, 3 pin, 5 and 15 Amps flush type complete all as specified and directed by the Engg-in-Charge.

S&F in replacement of in Ceiling rose on PVC Square Block surface bakelite 65x50mm, two to three terminals complete all as specified and directed by the Engg-in-Charge.

S&F in repair LED white colour 1x18 Watt, 220V, AC, Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use, connecting up with two/three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by the Engg-in-Charge.

S&F in replacement of Lamp holder, PVC/Polycarbonate type on square block with back plate suitable for batten fittings complete all as specified and directed by the Engg-in-Charge.

S&F in replacement of LED bulb 09 watt, 230 volts complete all as specified and directed by the Engg-in-Charge.

S&F in replacement Sheet metal enclosure for DB's Double door, single pole and neutral, 240V, 12 way with 200 Amp rated bus bar including blanking plates where required complete all as specified and directed by the Engg-in-Charge.

S&F in replacement 240 V 10 KA C curve miniature circuit breaker (MCB) SPN 40 to 63 Amp in the MCB DB complete all as specified and directed by the Engg-in-Charge.

S&F in replacement 240 V 10 KA C curve miniature circuit breaker (MCB) SP 5 to 32 Amp in the MCB DB complete all as specified and directed by the Engg-in-Charge.

S&F in replacement LED light fitting 1x9W/1x10W bulkhead luminaries including LED light driver holder connecting up three core flexible copper conductor cable of suitable size.

S&F in replacement of LED Flood light fitting 70 watt 5000 k green/natural white , IP>66, grey powder coated die cast aluminium housing , inbuilt energy efficent surge protected electronic driver, with all connected accessories complete all as specified and directed by the Engg-in-Charge.

S&F in replacement exhaust fan, steel body, AC single phase, 230 V of size 300mm sweep with blades and frame and louvers complete with cutting of suitable size of hole on wall with all connected accessories and making surface good after fixing omplete all as specified and directed by the Engg-in-Charge.

M&L for submain wiring comprising single core ,2 Runs of 6.0 sqmm nominal cross sectional area multi stranded FRLS copper conductor cable, PVC insulated unsheathed 1100 Volts grade drawing in and including min 25 mm dia PVC conduit ISI Marked(heavy duty) and its fittings on surface/recessed complete including provision of 1X6.0 sqmm nominal cross sectional area multi stranded FRLS copper conductor cable, PVC insulated unsheathed 1100 Volts grade as earth wire and using color code as per IS complete all as specified and directed by Engr-In-charge. ( Note :- Extra length of cables/ wire required for connection to MCBs shall not be measured and the rate quoted by contractor for per unit shall be deemed accordingly)

M&L for LT UG cable 2 core x 16 sq mm 1100 Volts grade XLPE insulated , armored, heavy duty with aluminium conductor laid in trenches or fixed to walls/ poles or passing through pipes with and including,cable gland lugs/ thimbles/ ferrules including taking down and connecting, testing and commissioning complete at site all as specified and as directed. Notes: (a) Excavation,RFR and protection pipe etc. Shall be measured and paid separately under relevant item of schedule

Returning filling, including spreading, levelling, watering and well remming in layers not exceeding 25cm thick complete all as specified and directed by Engr-In-charge.

Supply and laying in replacement double wall corrugated HDPE (DWC) pipe of size DN 40,pressure rating PN-8, in trenches for protection of cable complete all as specified and directed by Engr-In-charge.

S&F in replacememnt GI tubing light grade 40 mm bore as in cable protection fixed to poles/walls or laid in trenches/under road crossing etc complete all as specified and directed by Engr-In-charge.

Dismantling and M&L for Earthing complete with galvanised steel earth plate electrode of size 60cm×60cm× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to and including GI iron wire of size 4 mm dia by means of GI bolts, nuts, check nuts and washers, protected by 15mm bore GI light grade ISI marked pipe upto and including test points. Earth plate shall be surrounded by alternate layer 15cm thick of charcoal or coke and common salt all around bottom and top , 20mm bore GI medium grade ISI marked pipe for watering and including funnel,wire mesh,PCC chamber pit made with PCC(1:3:6) type C-1(using 20mm graded stone aggregate) including necessary form work, excavation and earth work in any type of soil, returning filling and disposal of surplus soil to a distance not exceeding 50M, CI pit cover duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified & shown in electrical plate No.3 of SSR 2009(Part-I) and all as directed. Note:- (i) Protection pipe and earthing strip upto test point from top of the earth plate and further upto the body of electrical equipment shall be included in the unit rate of this item. (ii) Earth testing arrangement should be done by contractor as per direction of Engr-In-Charge.

S&F in replacement of Switch socket combination with box piano type with bake plate 2 in 1, and 3 and 2 pin, 5 Amps complete all as specified and directed by Engr-In-charge.

S & F in replacement of Switch socket combination box piano type with bake plate 2 in 1,3 pin, 5 and 15 Amps complete all as specified and directed by Engr-In-charge.

M&L in replacement of sub main wiring for high bay lights of PVC insulated and PVC Round Sheathed 3-core Copper Conductor (flexible) industrial cable for Voltage Grade 1100 Volt, 2.5 sqmm in and including heavy grade PVC conduit of size 25 mm ISI mark and its accessories with fixing arrangements on pole surface, wall, ceiling etc complete all as specified and directed. Note : One run of 3-core Copper Conductor (flexible) industrial cable ,one run of PVC conduit together taken as one length for measuring unit length.

M&L in replacement for submain wiring comprising single core, 2 Runs of 4.0 sqmm nominal cross sectional area multi stranded FRLS copper conductor cable, PVC insulated unsheathed 1100 Volts grade drawing in and including min 25mm dia. PVC conduit ISI Marked(heavy duty) and its fittings on surface/recessed complete including provision of 1X4.0 sqmm nominal cross sectional area multi stranded FRLS copper conductor cable, PVC insulated unsheathed 1100 Volts grade as earth wire and using color code as per IS complete all as specified and directed by Engr-in-Charge. (Note :- Extra length of cables/ wire required for connection to MCBs shall not be paid separately and the rate quoted by contractor for per unit shall be deemed accordingly)

S&F in replacement High Bay Light, 150 watt, 6500 k , cool day Light , Suitable for ceiling(Surface/Suspended) mounted, IP>66 ,Black powder coated die cast aluminium housing, in built energy efficent surge protected electronic driver, with suitable size of clamp to fix/hang with ceiling and other all connected accessories to fix complete all as per sample at site and all as specified and directed . Make - Philips Cat part no. BY515P LED150S 5700 NB S1 PSU GR or equivalent in Crompton Cat part no LHB11-150-CDL/60-HPM or equivalent in Wipro Cat part no. LH21-182-060-57-X2

S&F in replacement Sheet metal enclosure for DB's Double door, single pole and neutral, 240V, 8 way with 200 Amp rated bus bar including blanking plates where required complete all as specified and directed by Engr-In-charge.

S&F in replacement load line distribution board double door type, TPN, vertical, 8 way, 415 V complete with incomming frame three pole , including bus bar, neutral link, blanking plates etc complete all as specified and directed. Make - Legrand Cat part no. 507747 or equivalent

S&F in replacement MCCB 3 Pole, 415V, 25 A to100 A,16KA complete all as specified and directed by Engr-In-charge.

S&F in replacement 240V 10 KA C curve miniature circuit breaker (MCB) SPN 32 Amp in the MCB DB complete all as specified and directed by Engr-In-charge.

S&F in replacement 1100 volts grade heavy duty 16 sqmm 2 core flat cable PVC insulated aluminium stranded conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended with suitable size of PVC conduit and saddle for whole length to fix on wall/surface complete all as specified and directed by Engr-In-charge.

Note : Deduction for amount of Rs. 2,01,346.50 as listed in Schedule 'A' Part-II (Schedule of Credit) shall be made while awarding of contract.

Ms/ ladakh technical services (BID ID -3390089)

KASHMIR FAIR DEAL SERVICES (BID ID -3389879)