NIQ01

Amount

LT PANEL :- Fabrication, painting & Supply at site including riverine (3rivers) & erection of INDUSTRIAL TYPE stand alone vertical, angle iron frame made LT PANEL with 14SWG CRCA sheet maded ........A, 500V , electrolytic COPPER bus bar chamber indoor suitable for use on 433 Volts 3-phase, 4 wire, 50 Hz system having required fault capacity, housed with incoming & outgoing interconnection etc. with indication lamps, accessories etc. devices are as follows :- I/C :- ………….A, 433V, 50 Hz , FP switch disconnector FUSE IN SS ENCLOSER -- 1no, 1 No. 3phase Kwh meter. , O/G :- FP, SS ENCLOSURE ………………...A, 433V, SWITCH DISCONNECTOR FUSE …….. ....nos , 415 V,32 A TPN M.S with HRC fuses - 1NO, 1 Set phase indication lights (R, Y, B) Solid state type (LED). 1 No. Volt Meter with VSS & control fuses. Make - AE., 1 No. Ammeter with ASS & CT's. make :- Meter - AE, CT - Kappa., 50mm x 6mm GI EARTH BUS BAR of required length with suitable terminal points.

Supply of 1C, ………...mm2, COPPER, 1.1KV grade unarmoured CABLE with PVC/XLPE insulation & seathed cable for drawing power to the luminairs at head frame of each high mast from HMLBD. ………….meter

Supply of 2C, 1.1KV grade, XLPE insulated & seathed ……….…..mm2 Aluminium armoured cable. …….……….meter. for drawing power to the luminairs at head frame of each high mast from HMLBD. ………….meter

Supply of 4C, 1.1KV grade, XLPE insulated & seathed ………………..mm2 Aluminium armoured cable. ………………...….meter.

Supply of 3.5C, 1.1KV grade, XLPE insulated & seathed ………….mm2 Aluminium armoured cable. ……………………………...meter LT PANEL TO HMLDB

Supply of 3.5C, 1.1KV grade, XLPE insulated & seathed ………………...mm2 Aluminium armoured cable. ………….meter LT PANEL TO HMLDB

Supply of 3.5C, 1.1KV grade, XLPE insulated & seathed …………………...mm2 Aluminium armoured cable. ………….meter. LT PANEL TO HMLDB

Supply of 3.5C, 1.1KV grade, XLPE insulated & seathed ………………..mm2 Aluminium armoured cable. For WBSEDCL'S METER TO LT PANEL……... …………. meter.

Laying of cable above 3½ core ……. sqmm and upto 3½ core ……… sqmm on wall/surface including S & F MS clams with earthing attachment in 2 x 10 SWG GI (Hot Dip) Wire, making hole etc. as necy., mending good damages and painting. ………….meter.

Laying of cable ........CORE………...SQMM to ….. core …….. sqmm on metallic structure /mast/pole/wall/surface /UG incl. S & F GI saddles with earthing attachment in 10 SWG GI (Hot Dip) Wire, making holes etc. as necy. mending good damages and painting complete. ………….meter.

Laying only Cable …………..CORE……………..SQMM to ………... sqmm through existing RCC/Hume/ GI Pipe/open masonary trench for single, 2, 3, 3½ & 4 core. ………….meter.

Laying of one No. cable .....CORE...........mm2 & upto ............sqmm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed. ………….meter.

Laying of two cables ............C ........... sqmm and to ................ sqmm in an underground trench in single tier formation (horizontal), the trench size : 680 mm x 760 mm average depth, with brick protection on the top of each cable 8 (eight) Nos. bricks per Mtr. and 4 (four) Nos. bricks per Mtr. as separator between the bricks and cables and also trench to be filled up with shifted soil, levelling up and restoring surface duly rammed. ………….meter.

Laying of THREE Nos. cable .........CORE above ........ sqmm and upto ............ sqmm in underground trench 680mm wide x 760mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per Mtr. including filling the space between the bricks and cable and also the trenchwith shifted soil, leveling up and restoring surface duly rammed. ………….meter.

COMPRESSION GLANDS :- Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC armoured cables for ………CORE, ……….mm2. …………nos

Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC armoured cables For 2C/3½/4C core ………………SWMM to ……………. Sqmm. …………nos.

…...DO ..upto ……………. Sqmm. …………nos.

….DO….upto ……………….. sqmm …………nos.

……DO……...upto ……………….. sqmm …………nos.

…….DO…….Upto ………………….sqmm ……...……nos.

Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials : 1C ……..SQmm …………nos.

…….do……2 core ………. sqmm cable …………nos.

…….do…... 3½ core …………….sqmm cable …………nos.

……do…..3.5 core ………………….. sqmm cable …………nos.

……do…..3.5 Core ……………………. sqmm cable …………nos.

……do…..4 Core ……………………. sqmm cable …………nos.

Supplying & fixing medium gauge GI Pipe ( ISI-Medium) Protection with necessary fittings and jointing metarials if required …….. mm dia……………….m

Supply & installation of 1000 W to 1500 W LEDFlood light luminaires with all accessories . Luminaire should be manufactured from High powerede LED Chip . Approved make for chip are of OSRAM / Nichia / Cree / Lumilad . Luminaire housing should be made up of PDC Aluminium / Extruded Aluminium with Glass cover and should confirm protection class of IP 66 and IK 08 . Lumen output of the fittings should not be less than 120 lumen per watt in CCT 5500+/- 365 deg K and CRI > 80% . Life expectancy of the luminaire should be 50,000 hrs at LM 70 . Luminaire should be supplied with 5kV internal and 10 kV external surge protection . Dimmable Driver should be constant current potted type with THD < 10% and PF > 95% . Bidder to submit LM 79 report from NABL approved test house and BIS certificate for both fittings and driver (supply quantity that is numbers of fittings to be supplied may be reduced as per direction of the authority concerned as per availablity of fund)........................numbers.

Thorough testing & Commissioning of the luminairs & overall systems by adjusting the positions & angles etc. so that the propoer & uniform illumination is achieved over the football ground as per FIFA guidelines 2011 for the Non televised Class I& class II levels of events for 200lux & 500LUX. Horizontal uniformities U1( Min/Max) = 0.5 & U2 = (Min/Avg)= 0.7.

Design, manufacturing, supply, erection of Hot dip galvanised, polygonal high masts with fixed head frame suitable for mounting ........... nos. of .......... KW LED Flood light and 1 no. AOL LED light fixtures complete with all accessories as required. The height of the mast from base upto top of head frame shall be ............... mtrs. The mast has been designed considering base wind speed as 230KM/HR (as per the client requirement). There shall be step ladder for High mast to access the top platform or Man-rider unit required.

Errection of the Hot dip galvanised, polygonal HIGH-MASTs with fixed head frame ( suitable for mounting 0f minimum ........nos. of .................KW LED Flood light fixtures ) supplied at the said site using suitable crain or suitable derick arrangement with own tools tackles & man power with all safety arrangement complete as demanded in the site as per direction of the EIC. The design of HIGH MASTS foundations must be vetted by the agency concern from any IIT or Jadavpur University.

Supply of foundation bolts manufactured from special steel along with nuts, washers, anchor plate and common template.

Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding literate or sand stone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom bailing out water as required complete. a) Depth of excavation not exceeding ................ mm. ………………..CUM.

Cement concrete (1:4:8) with graded stone chips (20 mm size) excluding shuttering and reinforcement if any in ground floor as per relevent IS codes. ………………………..CUM

Controlled Cement concrete with well graded stone chips (20 mm nominal size) excluding shuttering and reinforcement with complete design of concrete as per I456 and relevant special publications, submission of job mix formula afterpreliminary mix design after testing ofconcrete cubes as per direction of Engineer incharge.Consumption of cement will not be less than 300 Kg of cement with Super plasticiser per cubic meter of controlled concrete but actual consumption will be deter mined on the basis of reliminary test and job mix foumula. In ground floor and foundation. [using concrete mixture] (b) M 25 Grade a) Pakur Variety -- ………………………..CUM.

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape , placing in proper position and binding with 16 swg black annealed weir at every intersection , complete as per drawing and direction. a) In foundation,basement and upto roof of gr.floor/ Upto 4 Mtr. Tor/mild steel. ................MT.

Hire and labour charges for shuttering with centering and necessary staging upto 4metres using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels, curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor). .....................SQM

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below: (a) By ISI-Medium GI pipe......................SET.

Excavation of soil for installation of Earth Electrode and filling & ramming. (a) For Soft Soil………...……………….CUM

Extra for providing masonery enclosure on the top of the earth electrode of overall size 86.36 cm x 86.36 cm x 46 cm deep (below Ground level) complete with cemented brick work(1:6) of 25 cm width duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 cm x 35.56 cm with locking arrangement, GI reducer including drilling of 46 nos. 12 mm dia holes on the GI pipe...................SET

Extra for treatment of soil by using salt & charcoal or coke for plate electrode……………NOS.

Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 40 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required………………METER.

Connecting the equipments to earth busbar including S & F 4SWG GI (Hot Dip) wire of size as below on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damages.....................METER.

Connecting the equipments body to earth busbar incl. S & F 50 mm x 6 mm Galvanized (Hot Dip) MS flat on wall/floor with GI saddle as required and connection to equipments with incl. drilling holes, bolts, nuts,washers etc………………..METER.

Supply & inatallation of Low intensity LED type aviation obstruction luminaires to be mounted on high masts with nececery connectors, plugs ect & own tools tackles everything complete as per direction of the EIC……………….NUMBERS.

Testing commissioning of all the above items properly as per direction of the EIC & till the satisfaction of the EIC. & training of the operators.

Comprehensive maintenance of the whole system for 5 five years as & when required basis.

Bajaj Electricals Limited

VARIANT INFRATECH PVT LTD