Construction of 2 Nos Type-III Quarters for PWD Staff at Gohar Tehsil Chachiot, Distt. Mandi HP

Amount

Providing form work with steel plates 3.15mm(Three point fifteen millimeter) thick welded with angle iron in frame 30x30x5mm(Thirty millimeter into thirty millimeter into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and bellies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in situ-reinforced concrete and pain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge in:-

Flat surfaces such as soffits of suspended floors, roofs, landings and the like Floors etc. upto any thickness.

Beams, cantilever, girders and lintels sides and soffits of beams, beam hunching, cantilevers, bressumers and lintels in any depth in all height from floor..

Columns, pillars, Posts and struts, Square, rectangular or polygonal in plan

Edge of slab and breaks in floor and walls (under 20 cm width)

Providing and laying cement concrete M-30 1:1.5:3 (1 cement : 1.5 Sand : 3 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work. and reinforcement for reinforced cement concrete work as per Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Suspended floors, roofs ,landings and shelves and their support, balconies, beams, girders, breasumers and cantilevers upto floor level From Floor III to floor IV level

Columns, pillars posts and struts square rectangular polygonal in plain upto floor all level.From Floor III to floor IV level

Providing and laying upto all level reinforced cement concrete 1:2:4 (one cement : two Sand :four graded stone aggregate 20mm nominal size) mechanically mixed and vibrated to give an smooth and even surface including centring and shuttering etc. but excluding cost of reinforcement in String courses, copings, bed plates, anchor blocks, plain windows sills and the like as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . From Floor III to floor IV level

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire up to any level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Brick work using common burnt clay building bricks in super structure in cement mortar 1:6 (1 cement : 6sand) 2nd class brick. Floor III to floor IV level

Half brick masonry in common burnt clay building bricks in super structure in cement mortar 1:4 (1cement : 4sand) 2nd class brick (i) above plinth level Floor III to floor IV level

Providing and fixing anodized aluminum tower bolts (barrel type ) anodized trans parent or dyed to equired shade and colour with screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

200x10mm (Two hundred x ten millimeter)

150x10mm (One hundred fifty x ten millimeter)

100x10mm (One hundred x ten millimeter)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

125 mm (One hundred x twenty five millimeter)

100 mm (One hundred millimeter)

75 mm (seventy five millimeter)

Providing and fixing 100mm (One hundred millimeter) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete.300x16mm (three hundred x sixteen millimetre) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

300x16mm (Three hundred x Sixteen millimeter)

250x16mm (Two hundred fifty x Sixteen millimeter)

Providing and fixing 19mm thick ( Ninteen milimetre) thick terramite resistant water proof commercial board box including shelves and shutters, the back side of cupboard/cabinet of 8mm(Eight milimetre) thick ply and cut portions of shelves shall be finished with 6mm six milimetres) hard board edging. The cut portion of shutters from all the sides shall be finished with 12 mm ( twelve milimetre)thick hard wood edging. the shutters from out side shall be finished with 1mm (one milimetre) thick laminated of approved shade includng piano hinges and magnetic catcher with all ascessories as per detail architectural drawing No. 195/1 to 199/1 including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 10mm (ten milimetre) thick full body vetrified tiles of size 600X600 mm(six hundred into six hundred milimetre) of Nitco or equivalant approved shade and colour in flooring, treads of steps and landings laid over 12 mm (twelve milimetre) thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete.

Floor III to floor IV level

Providing and fixing 10mm (ten milimetre) thick full body vetrified tiles of size 600X600 mm(six hundred into six hundred milimetre) approved shade and colour in skirting 10mm (ten milimetre)(average) thickness base of cement 12mm (twelvw milimetre) mortar 1:3 (one cement:three sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete.

Floor III to floor IV level

Providing and fixing 10 mm (ten milimetre) thick WI-Paraquit or action tesa clip in prelaminated wooden flooring (H.D.F) with poly sheet & thermocoal sheet with door profile and side moulding locks with all fittings ,etc. complete as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.Floor II to III level

Providing and fixing 8 mm (eight milimetre) thick WI-Paraquit or action tesa clip in prelaminated wooden tile (H.D.F) with poly sheet & thermocoal sheet with door profile and side moulding locks with all fittings in riser, skirting, dado etc complete as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying marble work(Table rubbed and polished) in flooring 20mm (twenty milimetre) thick base in cement mortar 1:3(one cement:three sand) including jointing with cement mortar 1:2(one white cement:two marble dust) with an admixure of pigment to match the shade of the marble. 20 mm (twenty milimetre) thick .as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

6mm (Six milimeter) cement plaster to ceiling in cement mortar 1:3 (one Cement : three Sand) as per the directions of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering up to all floor level includingarises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:six sand)as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/concrete/stone wall for interior plastering upto floor all level including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:6 sand) as per the direction of Engineer-in-Charge including carriage of materials within all leads, and lifts other incidentals.

Providing 2nd (Second) class deodar wood work in frames of doors, windows, clerestory, windows and other frames wrought, framed and fixed in position complete as per specification and as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing 40 mm (forty milimetre) panelled glazed or panelled and glazed shutters in 2nd (Second) class deodar wood for doors windows and clerestory windows. Including black enamelled iron butt hinges as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing 40 mm (forty milimetre) thick 2nd (Second) class deodar wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 (eighty five) G. with wire of dia 0.56 mm (zero point fifty six milimetre)for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screw etc complete as per specification and as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals .

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease,dirt and other forein matter sand papering and knotting ready mixed paint with wood priming pink of approved brand and manufacture (Nerolac/Asian Shalimar) conforming to IS: 3536-1966 brushing as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with ready mixed paint brushing to give an even shade including cleaning of oil, grease,dirt and and other foreign matter sand papering and stopingready mixed paint other thanwhite as per direction od Engineer-in-including carriage of materials within all leads, lifts and other incidentals.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Distempering (Two coats) with oil bound washable distemper of approved brand and manufacture of and of required shade of undecorated wall surface to give an even shade over and including a priming coat with alkali resistance primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to give an even shade i/c thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth i/c applying of putty a required for making the surface as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing prepainted roofing with top skin of 0.60mm (Zero point six zero milimetre) thick preprinterd steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) micons primer coating to back coast of polyester of 5 ( five) microns over 5 ( five) microns primer coating including fixing with screws, prepainted iron J or L hooks, bolts and nuts 6mm(six milimetre) dia with prepainted limpet and rubber washer complete with all accessories as required as per specifications and as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts other incidentals.

Providing and fixing ridges or hips 60 cm (Sixty centimeter) overall with 0.60 mm (Zero point sixty millimeter) thick preprinted sandwich puff steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat or regular modified polyester organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with preprinted iron J or L hooks, bolts & nuts 6mm(Six millimeter) dia and preprinted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing valley 6cm (Sixty centimetre overall 0.60mm (Zero six zero milimetre)thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat og regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating including fixing with screws, preprinted iron J and L hooks,bplts & nuts & nuts 6mm (Six milimetre)dia and prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals

Providing and fixing flushing 38cm (Thirty centimeter) overall with 0.60mm ( Zero point six milimetre)thick pre painted sheet in roofing with hot dipped metallic Zink coated sheet with top coat of regular modified polyester organic coating of 20( twenty) microns over 5(five) microns primer coating + back coat of polyster of 5 ( five) microns over 5 ( five) microns primer coating i/c fixing with pre painted J or L hooks, bolts and nuts 6mm(Six milimetre) dia meter & pre painted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-In- charge.

Providing and fixing M.S. BP Sheet 1.66 mm (One point sixty six milimetre) to 2mm (Two milimetre) thick in eves board/ facia/soffit/ceiling including cutting ,fixing and welding to steel roof members and applying a coat of red lead primer complete as per direction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Steel work welded in built up sections, trusses and framed work,including cutting, hoisting fixing in positiobn and applying a priming coat of red lead paint as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals in:

In beams, joists, channels, angles, tees, flats with connection plates or angle plates as in main and cross beams, hip and jack rafter, purlins connected to comman rafter and the like.

Providing and fixing 85cm (eighty five milimetre)height railing with MS rectangular hollow pipe 75x50mm (seventy five into fifty milimetre) of 14 (fourteen)gauge M.S.black sheet make hand rail and M.S. square bars 20mm (twenty milimetre) size ballusters at 30cm (thirty milimetre) centre to centre duly welded with 2 (two) Nos. MS flat 40x6mm(forty into six milimetre) size and 20mm (twenty milimetre)M.S. square bars, lugs 10cm(ten centimetre). long at lower end of ballusters embeded in RCC steps or waist slab including priming coat of steel primer and painting with steel enamal paint other than white as per design and instruction of Engineer-In-Charge.

Providing and fixing on wall face 100mm (One hundred milimetre) dia PVC(D-Plast) rain water pipes of working pressure not less than 4.5Kg/sqm (Four point five kilogram per square metre) including filing the joint with approved adhersive complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing on wall face (D-Plast) accessories for rain water pipes including filling the joint with approved adhesive complete as per the direction of Engineer-in-Charge of materials within all leads, lifts and other incidentals.

PVC Plain Bend 100mm(One hundred milimetre) dia.

Shoe 100mm dia(One hundred milimetre) dia.

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil grease dirt and other foreignmatter and scoured with wire brushes fine steel wool scrubers and sand paper complete with ready mixed priming pant brushing red leadred oxide/zinc oxide chrome as per the direction of Engineer-in-Charge including of materials within all leads,lifts and other incidentals.

Painting two coats (excluding priming coat) on new steel and other metal surfces surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foregin matters Enamel paint other than white as per the direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing bright finished brass 100mm.(One hundred milimeter) Mortice latch and lock and a pair of levers, handles with necessary screws etc. complete (indian make of approved quality) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing glazed with glass panes of 4 mm (four milimetre) thickness weight not less than 10.00 kg/sqm (ten point zero zero kiogram per suqare metre) as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing bright finished hard drawn hooks and eyes as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.200mm(Two hundred milimeter)

Providing and fixing 115mm (one hundred fifteen milimeter) bright finished brass heaps and stapples (safety type) with necessary screws etc complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 150mm (one hundred fifty milimeter) oxidized M.S. single acting spring hinges with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. .

Applying cement slurry on RCC slab or cement concrete work using 2.75 Kg. (two point seventy five kilogram) of cement per square metre of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surface complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying cement concrete 1:6:12 (one cement : six sand : twelve) graded stone aggregate 40mm (forty milimetre)nominal size and curing complete exluding cost of centring and shuttering in foundation and plinth as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing to wall ceiling and floor galvanized mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floors as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

15mm (Twenty Millimetre) nominal bore

Making connection of galvanized steel distribution branch with galvanized mild steel main 20mm(Twenty Millimetre) to 40mm (Forty Millimetre) nominal size bore by providing and fixing tee including cutting and threading the pipes complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing vitreous China wash down, water closet European type. W.C. pan No 200049 in white shade with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1 (1 cement : 1 sand) of Parryware/Hindware/Jaguar or its equivalent as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing white plastic seat and cover for wash down water closet with C.P. Brass hinges and rubber buffers of Parryware/Hindware/Jaguar complete as per the direction of Engineer in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT White colour high density polyethylene / poly propylene 10 (ten) litres capacity ( full flush) European standard control low level flushing cistern No. 2602 of Parryware/Hindware/Jaguar with fittings with a pair of brackets with fittings such a lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm (forty milimetre) dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) .as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT jet spray of Cera/Hindware/jaguar with 1.5 mtr. Tube complete.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing vitreous China wash basin with single hole for pillar tap with cast iron or mild steel brackets painted white including cutting holes and making good the same but excluding fittings flat back:-(i) 550mmx400mm (six hundred thirty into four hundred fifty millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing vitreous China pedestal for wash basin complete recessed at the back for the reception of pipes and fittings as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing stainless steel kitchen sink of size 610 x460 x 200 No. 1022 of Paryag Polymers mm of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same (but excluding fitting) of Parryware/Hindware/Jaguar as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 32 mm (thirty two millimetre ) dia diametre C.P brass waste for wash basin or sink of approved brand and menufature as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing M.I. Union for wash basin or sink 32mm (thirty two millimetre ) dia size including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 32 mm (thirty two millimetre ) dia C.P. Bottle Trap for wash basin or sink as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 600mm x 450 mm ( six hundred x four hundred fifty millimetre) beveled edge mirror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing C.P. Brass Towel rail No 1581 of Jaguar complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws 600mm x 20mm (six hundred x twenty millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 600mm x 120 mm (six hundred x one hundred twenty millimetre) glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing toilet paper holder No 1533 of Jaguar/ESS-Ess or its equivalent in C P Brass as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing CP brass soap dish of Jaguar or its equivalent with brass bracket fixed on wooden cleat complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 15 mm (Fifteen millimetre) dia C.P. Brass bib tap with Capstan head of Jaguar as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 15 mm (Fifteen millimetre) dia C.P. Brass pillar tap with Capstan head 15 mm dia of Jaguar as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing P.V.C. connection with Brass unions 300/450 mm (three hundred/four hundred fifty millimetre) length15 mm(fifteen millimetre) nominal size as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing brass full way valve with wheel as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

15 mm (fifteen millimetre) nominal bore

Providing and fixing brass ball valve (horizontal plunger type) High pressure with polythene plastic floats 15 mm (fifteen millimetre) nominal bore as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete.110X90 mm (one hundred ten into ninty millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing high pressure PVC spigot and socket waste and ventilating pipes confirming to ISI -15328 SN8 of Supreme/Fenolex/Kitech marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 110 mm (one hundred ten) dia.

Providing and fixing 110 mm (one hundred ten millimetre) dia PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete /including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110 mm (one hundred ten millimetre) dia PVC door bend with oval access door insertion rubber washer 3 mm (Three millimetre) thick bolts and nuts ISI market complete including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110 mm (one hundred ten millimetre) dia PVC Collar ISI marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing 110 mm (one hundred ten millimetre) dia PVC plain bends ISI marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing 110 mm(one hundred ten millimetre) dia PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing PTMT grating sound of approved quality and collar 100 mm nominal dia.

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm (fifteen milimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level 1000 litres(one thousand litres) net capacity tank as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

M/S KESHAV CONSTRUCTIONS

ROOP LAL

MANOJ KUMAR

PAWAN KUMAR

DUGLA RAM