C/O High Court Guest House at Dharamshala in Distt. Kangra HP

Amount

Steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of red lead paint In beams joists channels, angle tee flat with connecting plates or angles cleate in beams or cross beams, hip or jack rafters, purlins connecting ,common rafter and in gratings framed guard bars, ladders, railling, brackets and similar works within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the compressive strength of 20N/mm2 (twenty newton per square millimeter) with cement contents not less than 330 kg (Three hundred thirty kilogram) per cubic meter to give an smooth surfaces mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in foundation, footings, bases of columns and the like and mass concrete in all depth / thickness upto all floor level within all leads, lifts of materials and other incidentals. as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing Tor steel reinforcement of Sail / Tisco for reinforced cement concrete work including bending, binding, straighting, cutting and placing in position complete including cost of binding wires complete for all floors within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Supplying and fixing rolling shutters of approved make made of 80 mm X 1.25mm (eighty millimetre into one decimal twenty five millimetre) M.S laths interlocked together through their entire length and joined together at the end by end locks mounted on specially designed pipe shaft,with brackets side guides and arrangements for inside and outside locking with push pull operation complete but excluding the cost of the top cover and spring within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Excavation in foundation, trenches etc. in earth work in all classification of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, including shoring, shuttering and pumping out water upto any depth or any quontam of water including slush which may be arise during de-watering removal of slush and stacking the serviceable and un-serviceable material clear from the edge of excavation as direction of Engineer-In-Charge and retuning the stacked soil in 15cm (Fifteen centimeter) layers, when required into plinths, sides of foundation etc; consolidating each deposited layer by ramming, watering and then disposing of all excavated earth as directed by the Engineer-in-Charge, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rates inclusive of octori, royality, Malkhana, toll taxes, GST and any other taxes imposed by the Government.

Second class brick work using common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:6 (One cement isto Six sand) within all leads, lifts of materials and other incidentals, as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

15mm (Fifteen milimetres) thick cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering upto all floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto six sand) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:5:10 (One cement; Five sand; Ten graded broken/crushed stone aggregate 40mm (Forty milimetres) nominal size) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Foundation footings, bases of columns and mass concrete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Applying Birla / J.K white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Finishing wall with Apex weather proof exterior grade emulsion of Asians Paints / Exterior Emulsion of Nerolac Suraksha paint as per approved shade approved design (Apexultima) on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 0.60mm (Zero decimal Six Zero milimetres) thick prepainted steel sheet ISI marked - Z 120 of tata / sail / reliance / jindal in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyster of 5 (five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks,bolts and nuts 6mm (Six milimetres) diametres with prepainted limpet and rubber washers complete with all accessories as required within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing ridges or hips 60 cm (Sixty centimetres) over all with 0.60cm (Zero decimal Sixty centimetres) thick prepainted steel sheet ISI marked - Z 120 of approved make in ridges (Factory made) of sail / relience / Jindal shall be having proper Gola/Shape of steel sheet Tata/ Sakti with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating of back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six milimetres) diametres with prepainted G.I. limpet and bitumen washers complete with all accessories as required within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing M.S. Grills of requirerd pattern in frames of windows and ventilators etcetra; with M.S. flat 20x5mm (Twenty into Five milimetres) and 8x8mm (Eight into Eight milimetres) solid, square or round bars with round headed bolts and nuts etcetra; or by screws, within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and placing water tank make P.V.C. SINTEX or equivalent having capacity of 1000 (One thousand) liters each tank with necessary fittings including over flow pipe scour pipe etcetera and pads required for in let and out let ball valve with cover and locking arrangements complete in all respect within all leads, lifts of materials and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Rajeev Kumar

Naveen Kumar

Munish Kumar

AMAN GORLA

Ashok Kumar

Kapil Sharma