Addn/Altn to Bldg No. P-04 (Officers Accn) at Escort line at Yol Cantt under AGE B/R-I of GE (KH) YOL

Amount

PART-I:- Dismantling plain or corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof covering, complete all as specified and directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets in ceiling, complete all as specified and directed.

Dismantling boarding, any discription fixed in any postion with nails, complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness, laid bedded and pointed in any mortar in floors, aprons etc. including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish of the premisses, including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins arches, pillars, including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Demolition of cement concrete reinforced of any description in any position complete including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Taking up or down 15mm bore, steel tubing and connections, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking up or down 20mm bore, steel tubing and connections, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking up or down 25 or 32mm bore, steel tubing and connections, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking down cement plaster on brick or stone walls, ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.50 Sqm each and removing from site, complete all as specified and directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.50 Sqm but not exc. 4 Sqm each and removing from site, complete all as specified and directed.

Taking down shutters of any description exc. 1 Sqm not exc. 2 Sqm each and removing from site, complete all as specified and directed.

Taking down shutters of any description exc. 1 Sqm not exc. 2 Sqm each and refixing the same opening/position, complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed stone ware, SWR, AC or RCC pipes) 75 to 110mm dia and removal of demolished materials from the site, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

Mat finish joint less (non skid), Premium class I grade, coloured, printed ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.06 Sqm but not exc. 0.11 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand) or chemical adhesive required to fixed with subbase including necessary cutting and waste as per site requirement, complete all as specified and directed.

Vitrified ceramic tiles light shade, 7 to 8mm thick glossy/mat finish double charged heavy duty (Square/ rectangular) polished, area of each tile exc. 0.18 Sqm but not exc. 0.38 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand), including necessary cutting and waste as per site requirement, complete all as specified and directed by Engr-In-Charge. Note:- The size, shade and design will be approved by GE.

Vitrified ceramic tiles light shade, 7 to 8mm thick glossy/mat finish double charged heavy duty (Square/ rectangular) polished, area of each tile exc. 0.18 Sqm but not exc. 0.36 Sqm, in skirting, dado etc and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick rendering in cement mortar 1:4 (1 cement : 4 coarse sand), including necessary cutting and waste as per site requirement, complete all as specified and directed by Engr-In-Charge. Note:- The size, shade and design will be approved by GE.

Glazed ceramic, premium quality, coloured/printed tiles of size 350mmx250mm /450mmx350mm /1200mmx600mmx7 to 8mm thick as in skirting, dado etc and the like, set and jointed in neat cement slurry or with chemical adhesive having 3mm horizontal spacing between them filled with neat and freshly prepared epoxy filled in the gooves cleaned or printed in white or coloured cement to match the shade of tile, laid over and including 10mm thick rendering in cement mortar 1:4 (1 cement : 4 coarse sand), including necessary cutting and waste as per site requirement, complete all as specified and directed by Engr-In-Charge. Note:- The size, shade and design will be approved by GE.

Black granite 16 to 18mm thick (table rubbed and polished) in steps, jambs, pollars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, laid over and including 15mm thick screed bed in cement mortar (1:6), including necessary cutting and waste as per site requirement pointed in white or coloured cement to match, complete all as specified and directed by Engr-In-Charge.

Rounding to edges of stone slabs of any type one edge, such as in steps cooking platform, cill of window and other simillar situations, complete all as specified and directed.

Machine cut kota stone slab flooring 16-18mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:6 (1 cement : 6 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish, complete all as specified and directed. Note:- Kota stone provided should be as single piece as in riser and treads or in any vertical surface.

Demolition of cement concrete (unreinforced) of any description and any position not otherwise specifically provided for, including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Plain cement concrete M-5 nominal mix, E-2, using 40mm graded mechanically crushed stone aggregate as in foundation, filling and mass concrete, as in sub base layer under floors, sunken floor, complete all as specified and directed.

Plain cement concrete M-7.5, nominal mix, type D-2, using 40mm graded mechanically crushed stone aggregate as in sub base to floor, 75mm thick, surface finished even and fair, complete all as specified and directed.

Rendering cement plaster 10mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (5mm thick first layers and 5mm thick 2nd layer), mixed with WPC @ 3% by weight of cement on fair faces of brick walls or on concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified and directed. Note:- water proofing compound shall be measured and paid seperately.

Supply only integral water proofing compound, complete all as specified and directed.

Providing and applying water profing treatement over terrace using SHALIURETHANE-BTD OF STP MAKE OR EQUIVALENT as approved by GE, high solid content single component water based liquid applied elastomeric water proofing membrene as ASTMC 836 and ASTMD 6083, thickness of the memberane shall be 1.50mm, having solid content of more than 80% elongation of 500+(-) 50% laid over reinforcing layer on non woven geo-textile mesh of 40/50 50gms, including applying self primer coat by diluting with 1:1 ratio @ 0.2 kg per sqm and suface preparation including cleaning of existing treatement, complete all as per specified and directed by Engineer-In-Charge.

Plain cement concrete M-15, nominal mix, type B-0, using 12.50mm graded mechanically crushed stone aggregate as in flooring, 25mm thick, surface finished even and rough for receiving floor finishes, complete all as specified and directed.

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5cm deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), complete all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).

Plain cement concrete M-15, nominal mix, B-0 using 12.50mm graded mechanically crushed stone aggregate as in lintels upto 1.50 metre clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates for serving hold fasts, filling in mild steel frames etc., kerbs, including weathering slighting rounded or chamfered angles and throating, complete all as specified and directed. Note :- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.

Reinforced cement concrete, M-15 (Nominal mix), type B-1, (with 20mm graded crushed stone aggregate as) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips, complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings facias, louvres, parapets and railings and similar work; not exceeding 200mm thick (Horizontal or sloping), etc. For fair finished flat surfaces of concrete, complete all as specified and directed.

Fly ash brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed.

Brick work with old size fly ash bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified and directed.

Walling random rubble masonry with best quality locally available stone, uncoursed, well bonded, bedded, solidly hearted and built in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified and directed.

All as per item No. 40 above but except stone.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (10mm thick first layers and 5mm thick 2nd layer), on fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement with WPC @ 3% by weight of cement, complete all as specified and directed. Note:- water proofing compound shall be measured and paid separately.

Rendering plaster 15mm thick in cement mortar 1:6 (1 cement :6 coarse sand) on other than fair faces of brick wall or stone wall surfaces, surface finished even and smooth without using extra cement, complete all as specified and directed.

Rendering cement plaster 10mm thick in cement mortar 1:3 (1 cement : 3 coarse sand) on ceiling, surface finished even and smooth without using extra cement, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of wall to prepare the surface even and smooth and applying finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), complete all as specified and as directed.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over 2mm thick plaster of paris putty including preparation of surface, complete all as specified and directed.

Preparation of newly plastered ceiling surfaces and applying two coats of oil bound distemper over 2mm thick plaster of paris putty including preparation of surface, complete all as specified and directed.

Material and labour for waterproofing of exterior walls including complete removal of existing plaster, including raking out joints, loose particles complete and applying two coats of acrylic polymer modified high performance coating (ASIAN-Smartcare Ultra Block 2k/BERGER-Home Shield 2k) or equivalent approved make. The treatment shall be done from ground level upto suitable height as directed and providing of 15mm thick cement plaster in CM 1:4 finished even and smooth, complete all as specified and directed by Engr-In-Charge. Note:- All treatment shall be done by applicator authorized by original equipment manufacturer with any mechanical means spray gun/roller. Make:- ASIAN PAINTS /BERGER /NEROLAC.

Preparation of old plastered or unplastered surfaces of wall including complete removal of existing surfaces and applying finishing walls with Acrylic Smooth exterior paint of required shade (Two or more coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), complete all as specified and as directed.

Preparation of old plastered wall surfaces and applying two coats of oil bound distemper over 2mm thick plaster of paris putty including preparation of surface, complete all as specified and directed.

Preparation of old plastered or unplastered surfaces of ceiling including complete removal of existing treatment and applying one coat of oil bound distemper over 2mm thick of wall care putty including preparation of surface, complete all as specified and directed.

Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick walls, complete all as specified and directed.

Mild steel galvanized iron water tubing 15mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor, complete all as specified and directed.

All as per Serial Item No. 53 above but except pipe. (Note:- Serviceable pipe retrieved from Serial Item No. 08 shall be used).

Mild steel galvanized iron water tubing 20mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor, complete all as specified and directed.

All as per Serial Item No. 55 above but except pipe. (Note:- Serviceable pipe retrieved from Serial Item No. 09 shall be used).

Mild steel galvanized iron water tubing 25mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor, complete all as specified and directed.

All as per Serial Item No. 57 above but except pipe. (Note:- Serviceable pipe retrieved from Serial Item No. 10 shall be used).

Mild steel galvanized iron water tubing 32mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor, complete all as specified and directed.

Sink with drainage board made of stainless steel 1.00mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 405mm x 355mm x 178mm of make Cat Part No SSSB-52 (Silver shine) of Blue Star or verall size 940mm x 455mm of make Cat Part No B4622101 (Gloss finish Diana Lite) of Cera, fixed in repair, complete all as specified and directed.

Angle valve/stop valves, cast copper alloy, chromium plated, fancy type, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repairs, complete all as specified and directed. Make: Cat. No.:F360006 of "HINDWARE" or Cat No. F1016201GG of "CERA" or Cat No. 8110 of "PRAYAG" or Cat No. TQT-526N of "ESSCO".

Bib taps, 15mm bore, cast copper alloy, chromium plated, fancy type with crutch or butterfly handle, screwed down high pressure, screwed for iron pipe or for brass ferrule, fixed in repairs, complete all as specified and directed. Make: Cat. No.: F360004 of "HINDWARE" or F2002152 of "CERA" or Cat No. 8108 of "PRAYAG" or Cat No. TQT-512 of "ESSCO".

CP central hole basin mixer with 450mm braided connection pipe (without popup) screwed down for iron pipe and fixed in repair, complete all as specified and directed by Engr-In-Charge. Make: Cat. No.: F2002461 of "CERA" or equivalent cat part of makes mentioned in Appx 'C'.

Sink mixer (wall mounted) with 165mm (6.50'') long swivel spout, connecting legs and wall flanges screwed down for iron pipe and fixed, complete all as specified and directed by Engr-In-Charge. Make: Cat. No.: F1020501 of "CERA" or equivalent cat part of makes mentioned in Appx 'C'.

Wall mixer with bend pipe for overhead shower screwed down for iron pipe and fixed in repair, complete all as specified and directed by Engr-In-Charge. Make: Cat. No.: F2002401 of "CERA" or equivalent cat part of makes mentioned in Appx 'C'.

Vitreous china wash down water closet (pedestal pattern), with flushing cistern (single piece EWC), coloured of size 800mmx375mmx650mm of Jaquar/ 700mmx370mmx745mm of Prayag/ 650mmx360mmx750mm of Hindware/ 720mmx370mmx760mm of Cera any other size as directed and including S traps, trap distance 180mm connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC coloured seat cover and CP jet/health faucet including PVC connection, fixed complete including demolition of old unserviceable WC and provision of PCC M-15, type B-1, using 20mm graded crushed stone aggregate, complete all as specified and directed. Make:- Cat Part No. ARS-WHT-39751P or ARS-WHT-39201 of jaquar, Cat Part No. ARTISAN 4390 of Prayag, Cat Part No. 20122 (S-22) or 20127 (P-18) of Hindware, Cat Part No. A1014112 of Cera. as directed by Engr-in-Charge. Note:- Size, shape and cat part will be approved by GE.

Soap dish approximate size 160x 160x90mm, chromium plated, fixed to plugs with chromium plated, brass screws, fixed in repair, complete all as specified and directed.

Sheet glass shelf assembly 55cm long consisting of 5.50mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, fixed with chromium plated brass screws, fixed in repair, complete all as specified and directed. Make:- Cat Part No ACN-1173N of Jaquar.

Soap dish, chromium plated, fixed to plugs with chromium plated, brass screws and fixed in repair, complete all as specified and directed. Make:- Cat Part No ACN-1131N of Jaquar.

32 mm dia, 450 mm long, galvanised iron, medium grade pipe as in spout of sunken floor, fixed, complete all as specified and directed.

Brass Chromium Plated, Tubular towel rail, 20mm dia, D type, 60cm long between flanges, with brackets, fixed with chromium plated screws, fixed in repair, complete all as specified and directed.

Wash hand basins, vitreous china (oval type, coloured) snow white of size 560x400x205mm, including brackets with 32mm bore waste fittings, brass, chromium plated with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, PVC connections 15mm size with CP brass coupling nuts of length 450mm, grating and union for discharge pipe, waste, chain and plug and porcelain stopper, chain and plug, PVC 32mm dia flush pipe and all accessories fixed in repair, complete all as specified and directed by Engr-In-Charge. Make: Cat. No.: S2030103 of "CERA" or equivalent cat part of makes mentioned in Appx 'C'.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement, dia of outlet 75mm fixed in cement concrete type B-1 (1:2:4), fixed in repair, complete all as specified and directed.

PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement, complete all as specified and directed.

S&F for 32 mm dia HDPE pipes of pressure rating 6 kgf/cm2(Waste pipe connect to Sink/WHB for removal of waste), complete all as specified and directed.

PVC connection 15mm size with PTMT nuts at boths end 600mm long and fixed in repair, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors bore 110mm, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors bore 75mm, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with adjustable clamps of bore 110mm, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with adjustable clamps of bore 75mm, complete all as specified and directed.

PVC (SWR) junction single, (Single T) equal or unequal, 75mm bore, provided with oval access door, fixed in repair, complete all as specified and directed.

PVC (SWR) bends any radius, 110mm bore (fitted with or without oval access door), fixed in repair, complete all as specified and directed.

PVC (SWR) junction single, (Single T) equal or unequal, 110mm bore, fixed in repair, complete all as specified and directed.

PVC (SWR) bends any radius, 75mm bore (fitted with or without oval access door), fixed in repair, complete all as specified and directed.

PVC (SWR) vent cowl 110mm, complete all as specified and directed.

Rotational moulded polyethylene water storage tank 1000 Ltrs capacity four layered (ISI Marked) cylinderical vertical with closed top, hoisted and fixed in position with ball brass valve, high pressure with Brass PVC float valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line, including taking down of old tank, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridge, hips, drip and straight flashing (length and girth fixed), fixed with self tapping screws, complete all as specified and directed.

Rolled mild steel joist channel, angle or tee section fixed independantly without connection plate etc. conforming to grade Fe.410-0.Gde-E-250, steel work, complete all as specified and directed.

S&F false ceiling of Non asbestos(Designer) 4 mm fibre cement building boards, manufactured from homogeneous mixture of cement, quartz and cellulose and cured with high pressure steam using auto claving process confirming to IS-14862, of size 600 mm x 600 mm x 4 mm thick fixed over and including Galvanise iron powder coated (minimum thickness of powder coating 50 micron) snap grid frame work of T section (main & cross member) of size 25 mm x 25 mm x 1.5 mm thick in square pattern of grid size 600mm X 600mm . The frame work will supported on side wall with the used of aluminium 'L' section of size 25 mm x 25 mm x 1.5 angles etc. Snap grid shall be supported with hangers of 4 mm dia Galvanised iron wire adjusting level fixed to roof slabs / truss etc by means of ceiling cleats made out of Galvanised iron flat of size 40 x 3 mm size 60 mm long and expansion hold fasteners 12.50 mm dia 40 mm long complete all as specified directed by the Engineer-in-Charge. Make : Everest or equivalent as approved by GE.

Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 85mm x 35mm double rebated comprises gauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC M-15, type B-0 (04 No's for each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including following fitting welded to frame shutter:-(i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window.(ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf.(iii) MS tower bolt 150mm long - 2 No per leaf(iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf.(v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf.(vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf.(vii) Flat iron fillets of size 20X3 mm for fixing wire gauge.(viii) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 06/07.Make : As per Appendix 'C'.Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day.

Mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed ballusters walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165, complete all as specified and directed.

Pressed steel frames for doors of size 105 mm X 60 mm X 1.25 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed including one shop coat of red oxide zinc chrome primer, complete all as specified and directed.

Pressed steel frames for doors of size 125 mm X 60 mm X 1.25 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed, complete all as specified and directed.

Plain cement concrete M-10, nominal mix, C-0, using 12.50mm graded mechanically crushed stone aggregate as in for filling in pressed steel frame/holdfast and mass concrete, complete all as specified and directed.

Mild steel flat Iron as in holdfast of size 25 x 3 mm thick of Fe 410 or Fe 310, complete all as specified and as directed.

35mm thick flush shutters, solid core construction with block board core and plywood face panels commercial type on one side and one face covered with decorative face veneer with lipping/frame to match type, supplied and fitted to chowkats, complete all as specified and directed by Engr-In-Charge.

Factory made second class hard wood (Sal) glazed and Skelton door shutters 35mm thick open rebated and prepared to receive glass gauge etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass or gauge etc., size of members of shutter as specified in clause 8.24 (a) of part-I, fitted to chowkats, complete all as specified and directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 100 x 50 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately), complete all as specified and directed.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative and designed type flush door shutter of size 30mm thick comprising of solid core single Leaf Flush Door of 25mm thickness, lipped with 15mm (5mm x 3) thick x 30mm width on one stiles and top rails & 10mm (5mm x 2) thick x 30 mm width on the other stiles & bottom rails. The inner panel Laminated with 2mm thick termite proof, water proof & fire resistant moulded PVC sheet with 2,4,6 raised panel design in different plain &/or prelam colors on one side after routing the mouldd design on flush door & 2mm plain and/or prelam PVC sheet on other side using rubber based adhesive on flush door & solvent cement adhesive on the lipping etc. complete as per direction of Engineer-in-charge, manufacture's specification and drawing.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet and edges shall be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 180 of MES SSR 2020 Part-II, complete all as specified and directed.

Factory made fully glazed PVC (frosted/ground/obscured) window/ventilator shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; complete all as specified and directed. Note:- Glass gauges inclusive of quoted rates.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks of galvanised wire staple fixed with stainless steel wire staples, fixed in repairs, complete all as specified and directed.

Sheet glass 3mm thick sheet glass, ordinary quality and glazing with oil putty/ wooden beads in square pane not exc 0.50 Sqm each pane in wooden/ Steel windows complete all as specified and directed.

S&F for 3mm thick figured glass, pin head type and glazing with oil putty/ wooden beads in square pane not exc 0.50 Sqm each pane in wooden/ Steel windows, complete all as specified and directed.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm, fixed in repair, complete all as specified and directed.

Applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surfaces of any description, exc. 10cm width or girth including preparation of surfaces, complete all as specified and directed.

Preparation of old painted wooden surfaces of any description and otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and as directed.

Applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, complete all as specified and directed.

Preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and as directed.

Butt hinges (ISI marked), medium weight, cold rolled, mild steel 100mm long, complete all as specified and directed.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 200mm, fixed, complete all as specified and directed.

Aluminium handles (ISI marked), cast type, anodised of size 150mm, complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 250mm with lipping frame to match, complete all as specified and directed.

Mild steel, 300mm, ordinary rat tail, rod pattern springs including roller and roller plate complete fixed to chowkhats, fixed in repair, complete all as specified and directed.

Taking down cement plaster/decayed concrete from RCC roof projections/upward parapet walls/down facia/soffits and fins of RCC chajjas/beams/columns/balconies etc. and also applying one coat of anti corrision paint to visible reinforcement if any. Supply and fixing by means of nailing wire netting of galvanised wire 1.40mm dia and mesh size 20mm and brushing neat cement slury with 3.00 Kg of cement/sqm and M&L for 20mm thick cement rendering in two layers of 10mm each (top/final layer shall be rendered after final setting of under layer) in Cm 1:3 on concrete surfaces including scaffolding at a height upto 7.00 mtrs etc, complete all as specified and directed.

Renovation of Kitchen and Supply & Installation of Modular Kitchen complete all as specified below and as directed by Engr-in-Charge :- Kitchen Cabinet Bottom Unit * :- Providing and fixing of machine crafted box type cabinet bottom unit 560mm depth using 19mm HDHMR board with 0.60mm laminate both sides. The shutters will also be machine crafted with the same HDHMR, with 0.60mm inside with factory laminated while on the out side it will be provided with 0.80mm laminate or 1mm laminate of glossy finish and a machined edge band of 2mm. The hinges will be auto loaded hinges of approved make, which is of IS marked. The shelf is to be adjustable with two slots provided at 300mm spacing so as to accommodate the shelf. The plywood should be of thickness 19mm HDHMR with 0.6mm laminate on top and bottom with machine cut edge band 0.50mm thick. Kitchen Accessories with soft closures :- (a) Cutlery basket 430mmx510mmx100mm (b) Cup & Soucer 430mmx510mmx100mm (c) Plate (Thali) 430mmx510mmx150mm (d) Plain 430mmx510mmx150mm (e) Plain 430mmx510mmx200mm (f) Degergent holder 430mmx510mmx200mm (g) Oil pullout 160mmx510mmx585mm (h) Telescopic drawer channels (j) Dustbin hoder

Renovation of Kitchen and Supply & Installation of Modular Kitchen complete all as specified below and as directed by Engr-in-Charge :- Kitchen Over head wall Unit* :- Providing and fixing of machine crafted box type over head unit 325mmmm depth using 19mm HDHMR board with 0.60mm laminated both sides. The shutters will also be machine crafted with the same HDHMR Board, with 0.6mm inside laminate while on the out side it will be provided with 0.8mm laminate or 1mm laminate of glossy finish and a machined edge band of 2mm. The hinges will be auto loaded hinges of approved make, which is of IS marked. The shelf is to be adjustable with two slots provided at 300mm spacing so as to accommodate the shelf. The plywood should be of thickness 19mm HDHMR board with 0.60mm laminate on top and bottom with machine cut edge band 0.50mm thick. Note:- *All measurement are to be maesured as LengthxHeight. However, the depth of the boxes are to be as per the specifications described above. Also, all the kitchen accesories are of approved make "KAFF/HETTICH/GODREJ and approved bhy Garrison Engineer. This rate includes the cost of dismatling timber framework and boarding in existing position.

100mm Adjustable pivot leg made of stainless steel/PVC ISI certified for holding kitchen bottom cabinet well supported over, complete all as specified and directed.

25mm dia mild steel power coated, fancy type curtain rod including curtain brackets fancy type brackets with rounded fancy type end knob, with antique finish or coloured suitable for holding 25mm dia single curtain rod, fixed in repair, complete all as specified and directed.

2nd class hard wood (Sal/Hollock) plain, solid, straight chowkats and frames, wrought, framed, rebated on solid, rounded or chamfered, put together with glue, pinned at joints with one or more rebates, complete all as specified and directed.

12mm Plywood Grade BWR type BB fixed with screws to timber frame/on walls to receive decorative laminate/mica over it, complete as specified and directed by Engr-In-Charge.

0.90mm thick decorative laminate type 1 of surface finish, colour and pattern as approved mica, fixed with approved adhesive on plywood or board as per manufacturer's instructions, complete as specified and directed by Engr-In-Charge.

Cupboard cabinet stainless steel hinges (Dadoo Kabza) suitable for 12mm thick wooden panel shutter with 4 hole/2 hole full overlay nickel plated to maximum 105' opening well fixed, complete as specified and directed by Engr-In-Charge. Make:- GODREJ, HITACHI

100mm size Aluminium alloy fancy handles, fabricated type, anodised, decorative type, fixed to shutter, complete as specified and directed.

Precast cement M-15 nominal mix, type B-1, using 20mm graded crushed stone aggregate as in landings, cover slab (for manholes etc.), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers, weatherings, throating etc. and setting in cement mortar 1:6 complete with joints to match, complete all as specified and directed.

Plain cement concrete M-10 nominal mix, type C-1 using 20 mm graded mechanically crushed stone aggregate as in surface channel and drains with proper finished surface, complete all as specified and directed.

Taking down point wiring with aluminium/ copper conductor for light point, fan & socket point/ power point etc. complete including switches, sockets, holders, (batten or pendent type), ceiling rose, switch board, bell/buzzer, bell push, and making good to the disturbed surfaces of wall/ floor etc. to match with existing surfaces including white wash/ colour wash/ distempering to match with existing wall/ floor/ ceiling finishes, complete all as specified and directed.

Taking down submain wiring any type and any size and making good disturbed surface by using cement mortar, white cement, putty etc. and match with existing surfaces of walls, floors etc., complete all as specified and as directed.

Taking down sheet metal enclosure DB, MCB, main switch etc and making good distrubed surfaces to match with existing surfaces, complete all as specified and directed.

M & L for Point wiring for one light controlled by one switch with 1.50 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) in and including PVC concealed conduit with sunken box suitable for modular switches and sockets, including 1.50 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) as earth continuity conductor connected to comman earth duly alongwith modular cover plate (inner & outer), complete all as specified and directed. Note-: (a) Insulation test of point wiring. (b) colour coding is to be maintained. (Ph-Red, N-Black, Half -Yellow, Earth- Green). (c) Rate of cutting chases, cement plaster, white wash and making good as existing surface included in quoted rates.

All as per serial item No '132' above, but for ceiling fan/ exhaust fan/ wall fan controlled by one switch 6 Amp, SP, ony way, 240V, complete all as specified and directed.

All as per serial item No '132' above, but for one 3 pin 5 Amps socket outlet on the independent board with 1.50 sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 1.50 sqmm stranded copper conductor cable as continous earth wire, complete all as specified and directed.

All as per serial item No '132' above, but for one 3 pin 5 Amps socket outlet on the same board with 1.50 sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 1.50 sqmm stranded copper conductor cable as continous earth wire, complete all as specified and directed.

All as per serial item No '132' above, but for bell/buzzer point controlled by one bell push, 240 volts, complete all as specified and directed.

All as per serial item No '132' above, but for one light point controlled by two way switches, complete all as specified and directed.

All as per serial item No '132' above, but for 5 pin 15 amps socket out let on independent with 2.50 Sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 2.50 Sqmm stranded copper conductor cable as continuous earth wire, complete all as specified and directed.

S & F for modular switch 10A one way, single module, complete all as specified and directed. Make : Havells Cat No AHCSXXW101, or Equivalent.

S & F for modular switch 16A one way 16A one way with indicator, single module, complete all as specified and directed. Make : Havells Cat No AHCSXXW161, or Equivalent.

S & F for modular bell push 10A, single module, complete all as specified and directed. Make : Havells Cat No AHCSBXW100, or Equivalent.

S & F for modular switch two way 10A, single module, complete all as specified and directed. Make : Havells Cat No AHCSXXW102, or Equivalent.

S & F for modular socket for 6A 2/3 pin combined, 2 module, complete all as specified and directed. Make : Havells Cat No AHLKPXW063, or Equivalent.

S & F for modular socket for 6A/16A 3 pin combined, 2 module, complete all as specified and directed. Make : Havells Cat No AHLKCXW163, or Equivalent.

S & F in for lamp holder polycarbonate body(Metal ring) with back bakelite plate suitable for batten fittings, complete all as specified and directed. Make : HPL Cat No EASMBHAWG, or Equivalent.

M & L for ceiling rose 65 x 50mm three terminals, fixed, complete all as specified and directed.

Supply and fixing electronic bell ding-dong AC 230 Volts single pole, complete all as specified and diercted.

Taking down carefully ceiling fan/exhaust fan any size/make with cable and all accessoreis remove from site to store for repair/overhaulling, complete all as specified and diercted.

Preventive maintenance and checking of Ceiling/Exhaust fans of any size/type/make, checking the serviceability of safety pins, clamps, down rods, rubber bushes, nuts, bolts, canopies and electric connections etc. reconnecting/hanging in original position, reconnecting the electric cables and testing, complete, all as directed. (Note : Items required to be replaced, over hauling & rewinding of fan motor if required will be measured and paid separately)

Dismantle the ceiling/exhaust fan of any size/sweep, cleaning, servicing, greasing the fan motor and reassemble the fan, complete all as specified and diercted. (Note : Items required to be replaced & rewinding of fan motor if required will be measured and paid separately)

Dismantling of ceiling fan 1200mm sweep and removing the burnt winding and Material and labour for rewinding the same with supper enamelled copper wire of existing size, gauge and turns including cleaning the slots properly and testing, complete all as specified and diercted.

Dismantling of exhaust fan 300mm sweep and removing the burnt winding and Material and labour for rewinding the same with supper enamelled copper wire of existing size, gauge and turns including cleaning the slots properly and testing, complete all as specified and diercted.

Material and labour for one coat of synthetic enamel paint by spray machine of ceiling fans any size/any make complete including filling cavities with filler, cleaning all dust etc and writing MES Nos, complete all as specified and diercted.

Material and labour for one coat of synthetic enamel paint by spray machine of Exhaust fans any size/any make complete including filling cavities with filler, cleaning all dust etc and writing MES Nos, complete all as specified and diercted.

Replacement of unserviceable louver for 300mm exaust fan, complete all as specified and diercted.

Supply and fixing in replacement of unserviseble condenser ISI marked 2.5 mfd, complete all as specified and diercted.

Supply and fixing in replacement of unserviseble condenser ISI marked 3.15 mfd, complete all as specified and diercted.

Taking down carefully storage type water heaters (Geyser) of any type and make of capacity upto 50 ltrs, after disconnecting their electrical and water connections. De-scaling the inner container, heating element, base assembly using diluted hydrochloric acid and cleaning thoroughly. Filling the inner container with water and detecting leakage including brazing as required to stop the leakage, if any, reassembling the geysers after replacing the u/s spare parts, filling water and testing the geysers by applying pressure by means of hand/foot operated pump, to ensure leak proof. Refixing geyser in the same original position/location and making the electrical/water supply connections incl testing on completion, complete all as specified and diercted. (Note : Items required to be replaced will be measured and paid separately under relevent items of the Schedule)

Supply and fixing Geyser Indicating lamp as per sample, complete all as specified and diercted.

Supply and fixing Thermostat rod suitable for Geyser 25/35/50 ltr, complete all as specified and diercted.

Supply and fixing Geyser Element 1000/1500 Watt. Make:Remson/Microking, complete all as specified and diercted.

Supply and fixing Geyser connection pipe 12/18'' long with sockets in both end, made of steel, complete all as specified and diercted.

Material and labour for Apparatus plate suitable for 25/35/50 ltr geyser all as per sample, complete all as specified and diercted.

Material and labour for painting of geyser of any size at site, white in colour including removing and refixing in its original or any other position properly, complete all as specified and diercted.

Supply only with replacement of inner container fabricated out of copper plate of 1.3 mm thick as per the existing size and suitable for up to 50 lts capacity vertical type geyser of any make as per the existing, complete all as specified and diercted.

S&F in replacement, insulating materials (new glass wool) fixed/punned properly in existing geysers of capacities 25 to 50 ltrs, complete all as specified and diercted.

M & L for LED tube light fitting 20 watt, 6000 K, 230 volt, box type complete bipin holders, connector block and retro LED rod of 20 watt polycarbonate diffuser having high efficacy (double side connection) complete with all accessories internally pre wired batten (double side connection) including connecting up with three core twisted flexible copper conductor cable of suitable size from ceiling rose to connector of light fitting including mounted on PVC square block, complete all as specified and diercted. Make : Havells Cat No LHEXAWP7UN1W020, or Equivalent. Note: (i) Contractor shall produce LM 79 & LM 80 test report form OEM owned NABL accredited laboraory. (ii) Contractor shall give gurantee of complete fitting/ fixtures for minimum of 2 years form the date of completion. (iii) Contractor shall conduct the inspection of company representative at site before installation of fittings/fixtures at no extra cost.

All as per Item No 167 above but LED light fitting mirror type with high output diffuser 2 feet, 10 watt, 6000 K, 220 volts, AC decorative type with extruded polycarbonate having efficiency 120 lumens /watt with driver holder including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and diercted. Make : Havells Cat No LHEXACP7IN1W010, or Equivalent.

Supply and fixing 17 Watt inverter Led Bulb 6500K, 1785lm, 230 volts, 50Hz, complete all as specified and diercted. Make : Wipro, Philips, Crompton or Equivalent. Make : Havells Cat No LHLDDDHBID3R017, or Equivalent.

Supply and fixing 20 Watt Led Bulb, 6500K, 2000lm, 230 volts, 50Hz, complete all as specified and diercted. Make : Havells Cat No LHLDDDHNID2R020, or Equivalent.

Supply and fixing round shape 18 watt, 230 volts, 6500 k, AC Surface type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and diercted. Make : Havells Cat No LHEAAHP7IL1W018, or Equivalent.

Supply and fixing LED security light of capacity 50 watt, 230 volts, 6500K, housing made of die cast aluminum with street optic lens with all accessories and connecting up with and including provision of 3 core flexible copper wire of size 1.50 sqmm from ceiling rose to security light drawn through GI light grade security light bracket not less than 1.50 mtrs in length alongwith fixing on wall, complete all as specified and diercted. Make : Havells Cat No LHETAVU7PA7J050, or Equivalent.

Supply and fixing for AC Ceiling Fan, single phase, 230 volts, 1200 mm sweep including grouting the ragged bolts in wall, fixing the frame on the exhaust side and connecting up with PVC insulated three core 1.50 sqmm copper cable from ceiling rose to exhaust fan, complete all as specified and diercted.

Supply and fixing for AC Hi speed Wall Fan, single phase, 230 volts, 400 mm sweep including grouting the ragged bolts in wall, fixing the frame on the exhaust side and connecting up with PVC insulated three core 1.50 sqmm copper cable from ceiling rose to exhaust fan, complete all as specified and diercted. Make : Havells Cat No FHWSW4SIVR16, or Equivalent.

Supply and fixing for AC exhaust fans, Steel body, single phase, 230 volts, 300 mm sweep including grouting the ragged bolts in wall, fixing the frame on the exhaust side and connecting up with PVC insulated three core 1.50 sqmm copper cable from ceiling rose to exhaust fan, complete all as specified and diercted.

Supply and fixing for AC exhaust fans, plastic body, single phase, 230 volts, 250 mm sweep including grouting the ragged bolts in wall, fixing the frame on the exhaust side and connecting up with PVC insulated three core 1.50 sqmm copper cable from ceiling rose to exhaust fan, complete all as specified and diercted.

S & F for MCB SP 6 to 32 amps 240 Volt,10 KA, 'B' series, complete all as specified and diercted.

S & F for MCB SPN 40 amps 240 Volt,10 KA, 'B' series, complete all as specified and diercted.

S & F MCCB four pole 125 amps adjustable type, 415 volts, 50 Hz ,breaking capacity, 16 KA including making all connections using bottle /pin copper thimbles, complete all as specified and diercted.

Supply and fixing sheet metal enclousre for DBs when MCB to be used double door powder coated factory made flush fixed complete with 200 amps rated bus bar 240 volts single phase 16 ways, complete all as specified and diercted. Note: MCBs shall be measure and paid seprately.

S & F of sheet metal enclosures distribution boards, double door, VTPN, 415 volts 4 ways, as per IEC 61439-3, degree of protection IP-43 (one incoming three phase & twelve out goings single phase) for MCCB & MCB,s comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed and comprising of the following:- (a) MCCB FOUR POLE 160 amps, AC, 415 VOLTS 25 KA=01 No (for incoming). (b) MCB SP 06- 40 amps = 12 Nos (for outgoings) complete with 250 amps fully insulated copper bus bar for each phase and neutral link, prefitted masking sheet fixed flush in wall including chases wall for fixing DB, complete all as specified and diercted. Note :- (i) The DB shall be VTPN series of Make : Indoasian Cat No 811888, or Eqvl make of L&T/ ABB/legrand. (ii) Connection of the MCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble properly crimped. (iii) All the vacant holes of the DB shall be provided with blank plates of appropriate size. (iv) Double continuous earth wire shall be provided for each three phase DB from earthing mains duly. (v) Cutting chasing shall be part of job at no extra cost. (vi) MCCB & MCB shall be measured and paid seperately.

M & L for submain wiring in and including PVC conduit 1.8 mm thick, 25 mm dia with two run of PVC insulated, unsheathed multistranded copper conductor of 10 sqmm (FRLS) and one run of PVC insulated, unsheathed multistranded copper conductor 10 sqmm (green in colour) for earth continuity conductor and connected to common earth dolly with thimble etc, complete all as specified and directed. (Two run of 10 sqmm plus one run 10 sqmm of earth wire will be measured as 1RM). Note: (a) Insulation test of point wiring to be carried out on completion of work. (b) Proper colour coding is to be maintained. (Ph-Red, N-Black,Earth- Green) (c) Two runs of single core cable with one run of earth cable and suitable size of conduit shall be measured as one RM. (d) Cutting chases for sub main wiring concealed PVC rigid conduit shall be deemed to be included in the quoted rate of item.

M & L for submain wiring in and including PVC conduit 1.8 mm thick, 20 mm dia with two run of PVC insulated, unsheathed multistranded copper conductor of 4 sqmm (FRLS) and one run of PVC insulated, unsheathed multistranded copper conductor 4 sqmm (green in colour) for earth continuity conductor and connected to common earth dolly with thimble etc, complete all as specified and directed. (Two run of 4 sqmm plus one run 4 sqmm of earth wire will be measured as 1RM). Note: (a) Insulation test of point wiring to be carried out on completion of work. (b) Proper colour coding is to be maintained. (Ph-Red, N-Black,Earth- Green) (c) Two runs of single core cable with one run of earth cable and suitable size of conduit shall be measured as one RM. (d) Cutting chases for sub main wiring concealed PVC rigid conduit shall be deemed to be included in the quoted rate of item.

Supply and laying Rigid Non-metallic PVC conduit for TV socket/telephone line 25mm external dia exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories nuts, saddles, pipe hooks etc, complete all as specified and diercted.

Supply and fixing of junction boxes for TV socket/telephone line (1 to 4 way), complete all as specified and diercted.

Supply and fixing of TV socket/telephone socket is fitted in Robust designed assembly plates smug fit on the wall with assembly plates with suitable modules, white in colour, dust free glossy finish, complete all as specified and diercted.

Supply and laying in trenches/through pipes or bare in road crossings/paths/drains/ ducts/floors/along poles/walls/ ceilings/ equipments etc. Cable Under ground, Heavy duty, armoured, XLPE insulated with stranded aluminium conductor, 25 sqmm x 4 core, 1100 Volts grade, complete all as specified and diercted.

Excavation in trenches in hard/dense soil not exceeding 1.5m wide and not exceeding 1.5m in depth for laying of cable and not exceeding 10 Sqm on plan for poles, struts, stays etc. and not exceeding 1.5m in depth and getting out, complete all as specified and diercted.

Returning, filling in, trenches including spreading leveling, watering and well ramming in layers not exc 25 cm, complete all as specified and diercted.

Removing excavated material to a distance not exc 50 mtrs and depositing where directed at a level n.exc 1.5 mtr above the starting point, complete all as specified and diercted.

Sand cushioning to under ground cables, 8cm thick layer before laying and testing the cable and 15cm thick after laying and testing of the cable in trenches complete all as specified in Clause 19.75 of MES SSR 2009 Part-I, complete all as specified and directed by Engr-in-Charge.

Supply and Laying Un-reinforced precast concrete cable cover class LV Type 1, flat size 250mm x 150 mm x 40 mm thick, complete all as specified and diercted.

Supply and fix Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, 230 volts, complete all as specified and diercted.

M & L for earthing complete with galvanised steel earth plate electrode, 600mm x 600mm x 6mm thick, buried directly in the ground (earth pit not less than 2.25m deep below normal (ground level) with top edge of the plate not less than 1.50m below ground level connected to galvanized iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point, GI tubing 15mm bore light grade protection pipe, GI watering pipe 20mm bore medium grade with funnel and wire mesh, charcoal and salt, 40mm thick pre-cast RCC (1:2:4) type B-0 (Nominal mix) cover reinforced with XPM (weighing n.less than 4 Kg/Sqm) with suitable steel handle, and angle iron 40X40X3mm frame and chamber of PCC (1:3:6) type C-0 (including earth work in any type of soil, removal of surplus soil to a distance n.exc.50m) and connecting, testing on completion, all as shown on electric plate No. 03 of SSR-2009 Part-I, complete all as specified and diercted. Notes: 1. Earth lead & protection pipes length upto & including 7.50 metre is included in the quoted rate. 2. Soil should be free from stone, boulders, aggregate, gravels etc.

RIHANA ENGINEERS (BID ID -3278569)

KISHAN CONTRACTOR (BID ID -3278157)

M/S SURINDER KUMAR MAHAJAN (BID ID -3282424)

Eshaan Construction Co. (BID ID -3278586)

MM Constructions (BID ID -3282348)