PROVN OF MAIN IRON GATE H COY 163 INF BN TA, 3X WC (I) TYPE FOR THASGAM AND SPL REP FOR BLDG NO. T-04, T-05, T-09 BLDG T-36 OF HQ 56 MTN BDE AND REPL OF LIGHTS AND WIRING IN BLDG T-124, T-02 OF 12 JAK RIF AT DRASS

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard dense soil.

All as above but depth exc 1.5 m & not exc 3.00 from GL -ditto-

M & L for PCC (1:4:8) type D-2, using 40mm graded stone aggregate as in foundations, fillings as mass concrete, complete all as specified and directed.

M & L for RCC (1:2:4) type B1 using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete. (Reinforcement shall be measured and paid separately)

M & L for RCC (1:2:4) type B1 using 20mm graded stone aggregate in slabs , beams and columns in floors, roofs, landings, canopies , shelves and the like. (Reinforcement and form work shall be measured and paid separately)

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for flat rough finished surface of concrete.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions having square, rectangular or polygonal shape with rough finished surface of concrete.

M & L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M & L for TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

S & F mild steel, plain black sheet 1 mm in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required

S & F MS framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc shall be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as directed conforming to Fe 410 W Gde E-250 A.

M & L for rendering 15mm thick on fair faces of brick work or concrete surface finished even and fair in cement mortar (1:6).

M & L for rendering 15mm thick on fair faces of brick work or concrete surface finished even and smooth without using extra cement in cement mortar (1:4).

M & L for two coats of cement based paint over one coat of primer on newly plastered wall surface including preparation of surface.

M & L for painting to steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces.

Returning, filling in, including spreading, levelling, watering and well ramming of soil in layers not exceeding 25cm thick.

Removing excavated soil to a distance not exceeding 50 mrtres and depositing where directed at a level not exceeding 1.5 m above the starting point.

M & L for PCC (1:2:4) type B1 using 20 mm graded stone aggregate in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete.

M & L for precast cement concrete block masonry with solid blocks, etc. exceeding 10cm in width made out of cement concrete (1:3:6) type C1 using 20mm graded stone aggregate and setting in cement mortar (1:6), complete.

Providing precast cement concrete solid building blocks or slabs 10cm thick in cement concrete (1:3:6) type C1 using 20mm graded stone aggregate (with plain or interlocking joints as directed) setting in cement mortar (1:4), complete, in walls

Earth filling including spreading, levelling and well ramming of soil in layers not exceeding 25 cm thick.

M & L for three coats of white washing on newly plastered surface including preparation of surface.

M & L for 75 mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base, floor, path, pavings etc.

M & L for 30 mm thick PCC (1:2:4) type B1 using 12.5mm graded stone aggregate as in sub base, floor, path, pavings etc.

M & L for screed bed or bedding layer 15mm thick in cement mortar(1:4) for laying floor finishes.

Non skid ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match (Screed will be measured and paid seperately)

M & L for second class soft wood, wrought, in scantlings 40 sqcm and over in section, unframed work.

M&L for second class soft wood plain, solid, straight chowkats and frames, wrought, frame rebated on the solid, rounded or chamfered, put together with glue pinned at joints.

S&F 2nd class soft wood factory made plain framed 35mm thick panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces (The size of rails and style as per IS 1003 (Part I), kiln seasoned and chemically pressure treated), rail and style made of second class hard wood.

S&F glazed and skeleton shutters 30mm thick using second class hard wood open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc; sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24(a); supplied and fitted in chowkats complete.

S & F 100 mm long butt hinges, med weight, cold rolled mild steel, and fixed.

S & F aluminium anodised, barrel tower bolts of extruded section and fixed, length of bolt 100mm.

S & F aluminium anodised, barrel tower bolts of extruded section and fixed, length of bolt 150mm.

S&F 150 mm long mild steel handle cast type

S&F mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, length of bolt 250mm.

S & F sheet glass, 3mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane

S & F 0.63mm thick galvanised mild steel sheeting with zinc coating of 120 gram/Sqm, grade 'O' with two corrugation side lap, with corrugation of Grade 'B' (12.5mm depth) fixed with coach screws and washers, in roofs, walls etc

S & F 0.63mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed).

S&F 75 mm bore cast iron, waste, vent pipe inn any length with or without ears, with cement joints fixed to wall.

S&F 110mm bore pipe PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor , complete all as specified and directed by Engineer-in-charge.

S&F PVC (SWR) P trap of 110/100 m size

S&F PVC (SWR) 110mm bore junction single, (single T) equal or unequal.

S&F vitreous china squatting pan, 'Orissa' pattern, size 580mm x 440mm, white, with integral foot rests including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. in repairs including making good to floor . (Rate exclusive of S& F of cistern)

Dismantling timber scantling 40 Sqcm and over in section, in any position (framed work).

Dismantling timber scantling in fillets, rails, posts, rafters, purlins etc under 40 Sqcm in section (unframed work).

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards / slabs / blankets, any thickness, including cover fillets.

S&F 9 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with nails to timber frame work complete, all as specified and directed by Engr-in-Charge

S & F 12mm thick, prelaminated particle board, interior grade, prelaminated one side with decorative lamination and other side balancing white lamination fixed with nails to timber frame work, complete all as specified and directed by Engr-in-Charge.

M&L for Plain fillets of second class soft wood (KAIL) sectional area exceeding 13 Sqcm and not exceeding 25 Sqcm, square, rectangular or triangular in section, clean sawn, secured with nails, complete all as specified and directed by Engr-in-Charge.

Taking down carefully copper or aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches ceiling roses, pendants, sockets bulk, head fitting, tube light fitting by unscrewing carefully from boards etc and making good, distrubed surface of walls floors etc. , complete all as specified and directed by Engr-in-Charge..

Point wiring with multi-stranded copper conductor PVC insulated and unsheathed cable in PVC casing and capping, 1.5 Sqmm with all fittings/accessories and including 1.5 Sqmm PVC insulated copper earth wire connected to common earth including closed recessed wooden terminal Boxes of suitable size made of 2nd class hard wood for mounting switches, sockets etc with 3mm thick laminated sheet cover for one light point or bell/buzzer point controlled by one switch, complete all as specified and directed by Engr-in-Charge..

All as per above item but for one 3 pin 5 Amps switch socket on same board -ditto-

All as per above item but for one 3 pin socket outlet 5 Amps on independent board -ditto-.

All as per above item but for one 3 pin 15 amps socket outlet independent with copper conductor cable FRLS, PVC insulated & unsheathed multistrand 2.5 sqmm including 1.5 Sqmm PVC insulated copper earth wire -ditto-

S&F Switch piano 5 Amps, single pole one way flush type, complete all as specified and directed by Engr-in-Charge..

S&F Switch socket combination 2 in 1, and 3 and 2 pin, 5 Amps Flush type, complete all as specified and directed by Engr-in-Charge.

S&F Switch socket combination 2 in 1, 5 and 15 Amps, Flush type, complete all as specified and directed by Engr-in-Charge.

S&F Ceiling rose surface bakelite 65x50mm, two to three terminals, complete all as specified and directed by Engr-in-Charge.

Sheet metal enclosure for DB's Single door, single pole and neutral, 240V, 8 way with 200 Amp rated bus bar including blanking plates where required, complete all as specified and directed by Engr-in-Charge.

S&F isolator SPN 240 volt 40Amp 10 KAcomplete all as specified and directed by Engr-in-Charge.

S&F MCB, single pole, 5 to 32 Amp, 240V, 10KA, complete all as specified and directed by Engr-in-Charge.

M&L for exhaust fan complete with plastic body, 240 V single phase of size 300 mm sweep incl making hole etc and fixation with 04 nos fully threaded bolt grouted in wall , nut and proding , wire mesh from out side complete with connection, complete all as specified. and directed by Engr-in-Charge

Rectangular block of second class hard wood of size 30 x 25 x 5 cm depth, closed recessed, complete all as specified and directed by Engr-in-Charge.

Supply and fixing LED 18 Watt Tubelight fitting decorative ultra slim square profile linear with extruded polycarbonate environment friendly Make Havells Cat part LHEXBTP7INW018, complete all as specified and directed by Engr-in-Charge.

Earthing complete with galvanised steel earth plate electrode 600mm x 600mm and 6mm thick buried directly in ground not less than 2.25 mtr deep below normal ground level with top edge of plate not less than 1.5 metres below normal ground level, connected to the Galvanized iron earth wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron protected by provision of G I light grade pipe 40mm bore including provision of concrete pit in PCC 1:2:4 type B1 using 20mm grade stone aggregate with 40mm thick cover of RCC 1:2:4 reinforced with XPM (weight not less than 4Kg/Sqm) and frame of angle iron 25x25x6mm with lugs two number and with 6mm dia MS bar handle made to shape and GI medium grade 20mm bore pipe for watering perforated at bottom 1.75m long placed on top edge of earth plate, common salt and charcoal filling, test point made out of 40mmx8mm flat iron with fixing arrangement funnel wire mesh and earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50M all as per electric plate No 3 of SSR Part-I conected to earth test point as specified or indicated including testing on completion.

S&F insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area 10 Sqmm 2 core complete all as specified

S&F insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with copper conductor, 1100 volts, grade cross sectional area 6 Sqmm 2 core complete all as specified

S&F housing service bracket (hook type) complete with 3.00 m long GI pipe 40 mm dia med grade, 2 Nos bend, MS hook & stay complete all as specified & directed.

Note : - Contract sum will be derived after deduction of Rs. 64280.00 as listed in Schedule `A` Part -II (Schedule of credit).

M/S Azad Construction