CONSTRUCTION OF MULTIPURPOSE HALL FOR BDDHIST COMMUNITY AT LAKHANWALA, VIKASNAGAR, DEHRADUN

Amount

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with gola sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size).

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx400micron, finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement rounding the edge sand making and finishing the outlet complete.

Providing and laying 60 mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long co mplete as per standard design With common burnt clay F.P.S. (non modular) bricks of classdesignation 7.5

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixedwith water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge :

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge.

Cartage of material by mannual labour inculding loading ,unloading & stacking up to 2km

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 20 mm thick cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 500x500 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 20 mm thick cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 800x800 mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab of all colour and texture except Black, Cherry/Ruby Red

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :110 mm diameter

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.Coupler(110 mm)

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.Bend 87.5 degree 110 mm bend

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.Shoe (Plain) 110 mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs,screwed with M.S. screws of required length including

12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand)

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water tinnable priming coat with cement primer

Finishing walls with water proofing cement paint of required shade New work (Two or more coats applied @ 3.84 kg/10 sqm)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

12 mm cement plaster finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand)

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete..

Providing and fixing soil, waste and vent pipes : 100 mm dia Sand cast iron S&S pipe as per IS: 1729

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), including necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design :With 20x20 mm square bar

Providing & fixing of foot rest in tank

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality 19.19.1 L D- 2.5 Rectangular shape 600x450 mm internal dimensions

Providing & fixing of R.C.C manhole covering tank (600 x 600)

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars 250 mm dia. R.C.C. pipe250 mm dia RCC pipes.

Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :1.68 m deep with SFRC Cover and frame (heavy duty HD20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :

Excavating trenches of required width for pipes, cables, etc including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level.300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200mm

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete .Thermo-Mechanically Treated bars

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge..All works upto plinth level

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge..All works above plinth level upto floor V level

Centering and shuttering including strutting, propping etc. and removal ofform for :Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal ofform for :Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal ofform for :Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal ofform for :Columns, Pillars, Piers, Abutments, Posts and Struts

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper

Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head,comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge.Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for : (i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (ii) Sites with structure height more than 20m for all wind speedsCasement cum fixed panel window having one single casement panel & one fixed panel with S.S 304 friction hinges as per size and weight of sash, multi-point locking system, zinc alloy (zamak) powder coated handles. Using R2 series with frame (39 mm & above ) x (39 mm & above) & sash (39 mm & above) x (60 mm & above) & mullion (39 mm & above) x (60 mm & above). (Height upto 1.2 metre; each openable shutter upto 0.8m width)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :300x16 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :250x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyedto required colour or shade, with necessary screws etc. complete :250x10 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyedto required colour or shade, with necessary screws etc. complete :150X10 MM

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.15 mm dia. nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.20 mm dia. nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.50 mm nominal outer dia Pipes

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore.

Providing and fixing uplasticised PVC connection pipe with brass unions : 15 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :25 mm nominal bore (Horizontal)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked black solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing soil, waste and vent pipes :100 mm dia Sand cast iron S&S pipe as per IS: 1729

Providing and fixing soil, waste and vent pipes :75 mm diameter :

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :for 110 mm dia pipe

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :for 75 mm dia pipe

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Circular shape 450 mm dia

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing double equal plain junction of required degree.100x100x100mm

Providing and fixing double equal plain junction of required degree.75x75x75x75 mm

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete100 mm diameter pipe

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete75 mm diameter pipe

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (including equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles above 25 mm and up to 40 mm

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Supply & fixing of auditorium chair complete in all respects with labor as per direction given by engineer in charge. Make- Geeken, Godrej, Delite.

Supply & fixing of steel almira for books complete in all respects with labor as per direction given by engineer in charge. Make- Geeken, Godrej, Delite.

Supply & fixing of wooden table complete in all respects with labor as per direction given by engineer in charge. Make- Geeken, Godrej, Delite.

Supply & fixing of chair complete in all respects with labor as per direction given by engineer in charge. Make- Geeken, Godrej, Delite.

Echo Wood Panels

Providing & Fixing of ECOWOOD Linear grooved slats sound obsorption panels HDF based melamine finish sound absorption panel on wall or ceiling over existting substrate. The panels are made of fiber rated red color high density fiber board of density about 800 Kg/M3 with low formaldehyde content. The top surface is laminated with melamine finished. Each panel is having tongue and groove structure on the long side with an additional groove. To hold the clip of size 2440mmX128mmX15mm. The back of each panel is pasted with acoustic fleece of density 80Kg/m3. The front of the panel is grooved in width of 2mm and depth of 4mm. while the back is perforated with holes of dia 10mm at a distence approximately 15mm center to center. The installation to be done on an alumunium channel with galvanised steel clip system. The channel is of dimention L-2440 X W-25mm X D-20mm with the clip for each panel of size 43mmX40mm. Each Channel is fixed at a distence of 600mm. Once intallated, the edges of open are covered with L Profile of similar shade etc complete.

Providing & Fixing of Acoustic Wall Panels

Providing & Fixing of Acoustic Wall Panels. Speccifications as given below:- Material 100% Polyster fiber size 1220 X 2440 X 9 mm, Density 1800 Kg/m3, Fire Resistence, Heat insulation, Non Toxic, Light weight etc complete

Providing & Fixing of Laminated Wooden Flooring

Providing & Fixing of Laminated Wooden Flooring. Speccifications as given below:- Grade - AC5, Heavy commrecial, 154.5 x 1195 x 12mm etc complete

Pre Fab Roof Structure

Supply, Fabrication, Paint of Steel structure & eraction (at site with all requirement tools and trackles) for multipurpose hall etc complete.

Mural Art Work

SITC of mural work .While there is no shortage of images to capture in a mural, there are three general types of this kind of art : Photography murals, painted scenery etc complete.

Supply, Installation, Providing design, testing and commissioning of curtain motorised system for stage etc complete.

WGSTLPT Point wiring in PVC conduit, with modular type switch.Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.Group C

WGSTLMIDTC Twin Control point wiring in PVC conduit, with modular type switch:Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.

WGSTLPP2 Power plug wiring in PVC conduit (2x4 sq. mm)Wiring for light/power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring fir curcuit/ submain wiring alongwith earth wire the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring fir curcuit/ submain wiring alongwith earth wire the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.4 X 6 sq. mm + 2 X 6 sq. mm earth wire

Wiring fir curcuit/ submain wiring alongwith earth wire the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair

Supplying and fixing of following sizes of PVC conduit along with accessories in surface / recess including painting in case of surface conduit, or cuttting the wall and making good the same in case of recessed conduit as required.25 mm

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.75 mm X 75 mm X 60 mm deep

PTSWEB S/F modular type switch/ socket: Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

PTSWEB S/F modular type switch/ socket: Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

PTSWEB S/F modular type switch/ socket: Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Telephone socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing 3 pin, 5 amp. ceilling rose on the existing junction box/ wooden block including connection etc. as required

Supplying and flxing brass batten/angle holder including connection etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling / wall, including connection with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq, mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation of exhaust fan upto 450 mm sweep in the existingopening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as required.

Extra for fixing louvers/shutters complete with frame for a exhaust fan of all sizes.

PWTPMCBDB S/F TP MCB DB:Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way (4 + 24), Double door

MCBTPIS S/F TP MCB isolator:Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissoning etc. as required.63 amps

MCBC S/F 'C' curve, SP MCBSupplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc.with charcoal/ coke and salt as required..

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supply of AC 230/250 volts, 50 HZ energy efficient ceiling fan with standard down rod, blades, 3 nos. caps Model-ES 50 (1200 mm Sweep) etc. complete in all aspects as per direction of Engineer in Charge1200 mm sweep

Supply of AC 230/250 volts, 50 HZ exhaust fans including providing nuts, bolts, mounting frame and other accessories etc. complete . Model- Ventil Air - DS (Make : Havells) 300 mm sweep 900 rpm ,complete in all aspects as per direction of Engineer in Charge. 300 mm sweep 900 rpm

SUPPLY OF LED Glass Bulb B22, 15 W ,6000k /4000k/3000K ,230/250 Volt,50 HZ ETC, complete in all aspects as per direction of Engineer in Charge.

Supply and fixing of LED Tube light 1200mm 20W 865 T8 IP20 ,Lumen Output-1600 , 3000, 4000, 6500K ceiling mounted LED batten (E-LITE LED TRIYCA) , extruded aluminium heat sink provided for efficient heat deissipation 7& integrated electronic driver. ( 1x20 W LED Double 6500K) complet in all aspects as per direction of Engineer in charge.

Supply & fixing of steel wall fan 600 mm sweep complete in all respects as per direction given by engineer incharge.

Fire fighting

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.150 mm. Dia

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585. 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.40 m

Supplying and fixing single headed internal hydrant valve with instantaneous unmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :Single headed Stainless steel

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :150mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :Gun Metal

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads. 1620 lpm at 56 m Head

Providing and fixing of ABC type (Stored Pressure) Fire Extinguisher I.S.I marked & T.A.C.approved complete in alrespect. 2 Kg capacity

Providing and fixing of ABC type (Stored Pressure) Fire Extinguisher I.S.I marked & T.A.C.approved complete in alrespect. 4 Kg capacity

Supplying & Fixing Sand Bucket

Solar

Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:- a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. c) Data Monitoring System complete with accessories. d) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. e) Lightning and surge voltage protection. f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required.

VIDEO SYSTEM

Supply, Installation, Testing & Commissioning of 3-chip LCD technology, Brightness - 13,000 Lumens, Panel Size - 1.0 Inch, Dynamic Contrast - Over 2,500,000:1, Mechanical Shutter, SDI (3G) Input and Output, NGC Tag and Simple Stacking - Yes, Filter Less Maintenance Cycle, Laser light source — long life; custom brightness modes, Compact and lightweight for installation flexibility, Fan Noise (Normal/Eco or Quiet)- 32dB/30dB, Sealed light source and optical engine, Access automated tool set with optional camera, Auto colour calibration and screen matching, Motorized lenses with lens position memory, Sealed light source and optical engine — IP5X Rating, Fast Simple Stacking function using remote controller, Easy maintenance — fast access to key units, DMX Art-Net easily integrates with lighting protocols, Mechanical shutter, Laser-based dimming for fade to black, Projectors include HDBaseT, HDMI®, VGA and LAN inputs. SDI inputs and outputs are standard. HDBaseT technology simplifies installation with just one Cat5/6 cable, carrying full HD video, audio, network and control commands, NFC Technology, BUILT-IN MEDIA PLAYER AND OVERLAY EFFECTS etc complete. MAKE - SONY/ EPSON/ PROMARK/Barco/Christie.

Supply, Installation, Testing & Commissioning of Zoom / Focus Powered Lens with shiftVertical: +/- 50% Horizontal: +/- 24%. Aperturef/1.8-2.0. Screen size60" to 600" etc complete. MAKE - SONY, EPSON, PROMARK , Barco,Christie.

Supply, Installation, Testing & Commissioning of Cyclorama screen with all sided 3” alumimum frame with black powder coated finish. Seamless HD 4k Matt white fabric. Perflat flat screen with screen size- 250" diagonal view area. 123/218" with frame 130"/225" max etc complete. Make- PRIMA, EPSON, PROMARK,Elite,Grandview

Supply, Installation, Testing & Commissioning of A/V line switch with Gigabit Ethernet PoE+ Ports, Switch etc complete. MAKE - NETGEAR, D-LINK, TP-LINK , Cisco

Supply, Installation, Testing & Commissioning of HDMI 4X4 Matrix switcher with 18 Gbps (600MHz) or better 4K UHD support or better. HDCP 1.4 and 2.2 compliant or better Supports HD resolutions up to 3840x2160@60Hz (YUV4:4:4,8-bit) or better & 4096x2160@60Hz (YUV 4:4:4,8-bit) or better. Supports 48-bit Deep Color up to 1080p 60 or better. Supports pass-through of LPCM 7.1 or better, bitstream and HD bitstream audio formats over HDMI or better. Controllable via front panel buttons or better, RS-232, Telnet, WebGUI and IR remote or better. Product should be CE and FCC certified etc complete. MAKE - KRAMER, ATEN, EXTRON, CYPRESS, Crestron

Supply, Installation, Testing & Commissioning of HDMI to USB video capture recorder with HDMI bypass can support resolutions upto 18Gbps (600MHz) 4K UHD with HDR (via the by pass path) while simultaneously streaming the audio and video signal at 4K@60 to a USB connected PC for capture or rebroad cast UHD+HDMI to USB-C Capture with HDMI IN and HDMI OUT. HDMI IN /Output HDCP support v1.4 and v2.2. AudioIN support LINEIN and MIC IN. Supports video timing stabilization to help ensure areliable and stable etc complete. MAKE - CYPRESS, ATEN, KRAMER, Crestron

Supply, Installation, Testing & Commissioning of i5 desktop pc with 500GB SSD, 8GB RAM with keyboard and mouse. (i5 Desktop PC) etc complete. MAKE - PROMARK, DELL, HP, Lenovo

Supply, Installation ,testing and commissioning of 32 UA/V Rack with 19" 600mm(W) 650mm(D), Front Glass door 32u, Rear steel door 32u, Coaster Wheel with front brake, Fan 90cfm 230vac, 19" two stationary shelf 375mm depth, PDU 7x2 points etc complete. MAKE - VOLRACK, MTS, FINETRACK

Supply, Installation, testing and commissioning of projector ceiling Mount kit as per site.

Supply, Installation, testing and commissioning of projector ceiling Mount kit as per site.

Supply, Installation, testing and commissioning with cables and connectors programming.

AUDIO SYSTEM

SITC of High Power 2-Way Loudspeaker with 1x15” LF & Rotatable Horn,1x15” LFfull range two-way speaker, Coverage Pattern: 90°x50°, rotatable wave guide, Frequency Range= 34Hz–20kHz, Frequency Response (±3dB): 40Hz – 20kHz, Maximum SPL =130dB Peak (Passivemode), Passive Crossover Frequency: 1.2 kHz, Sensitivity = 96dB SPL (Passive mode), 2400W peak at Passive mode,Should have Bi-amp mode, High Frequency Driver:1.5 in etc complete. MAKE - JBL/L-Acoustics/ Promark/D&B

SITC of Custome Mounting Arrangement etc complete.

SITC of Four-channel, 2200W per channel@4Ω and 1,300Wx4 @ 8ohm Power Amplifier, Voltage Gain at 1kHz:38 at 4 ohm, Frequency Response(at 1W, 20Hz to 20kH zinto 4 Ω) : ±0.5dB, THD(at 20Hz–20kHz) 0.35% , SNR Analog input>104dB ,Damping Factor (20Hz to 100Hz) :>1000, CROSSTALK > 80dB, Network Control at RJ4 5, DIGITAL SIGNAL PROCESSING:96kHz, 32-bit floating point, Shall have GPIO port for 3rd party control, Shall have LCD display and signal LED's for input/output etc complete. MAKE - Crown/ L-Acoustics/Promark/D&B

SITC of High Power Subwoofer 2x18",Frequency Range:28Hz –1kHz,Power Rating :9600W Peak, Maximum SPL 30 to 500HZ=142dB Peak, Sensitivity 30 to 500HZ =102dB Peak, Nominal Impedance: 4ohms, Input Modes: Drivers Parallel/ Drivers Discrete etc complete. MAKE - Crown/ L-Acoustics/Promark/D&B

SITC of Power Amplifier, Input Channels :2 or better Power output : 3000watts 2ohm stereoperch, 2100 watts 4ohm stereoperch,1200watts 8ohm stereoperch, 4200watts 8ohm bridge mono, 6000watts 4ohms bridge-mono or better, Sensitivity (for full rated power at 4ohms): 1.4VRMS or better, Frequency response (at 1watt,20Hz-20kHz):+0dB,– 1dB or better, S/NRatio (below rated 1kHz power at 8ohms): 103dB or better, THD:<0.5% or better, Damping factor (20H z to1kHz):> 500 or better, Crosstalk (below rated power):20kHz-1 kHz:>70dB or better, maximum input signal: +22 dBu typical or better, etc complete. MAKE - Crown/L-Acoustics/Promark/D&B

SITC of compact 2‐Way Loud speaker, Shall have Frequency Range: 58Hz-20kHz (-10dB), Frequency Response: 68Hz–19kHz (±3dB),Coverage Pattern- 120°x60°, System Sensitivity (dBSPL, 1W@ 1m)-92dB ,Maximum SPL: 113dB, Nominal Impedance: 8Ohms, Power Handling (Programme): 500W, etc complete. MAKE - JBL/L-Acoustics/Promark/D&B

SITC of Wall Mount Bracket for above Loud speaker, Wall Mount kit should be made by same speaker OEM, Should have powder coating, etc complete. MAKE - JBL/L-Acoustics/Promark/D&B

SITC of Compact 2-way Loud speaker with 2x8” LF, 2-way loud speaker system with 1500W Peak, 2x8" LF driver, Coverage Pattern=120°x60°, Frequency Range=54Hz-20kHz, SPL=120dB, System Sensitivity 1:94dB SPL/1W/1m, Crossover: 2.1kHz, etc complete. MAKE - JBL/L-Acoustics/Promark/D&B

SITC of Wall Mount Bracket for above Loud speaker, Wall Mount kit should be made by same speaker OEM, Should have powder coating, etc complete. MAKE - JBL/L-Acoustics/Promark/D&B

SITC of multichannel network based power amplifier :- Four-channel, 2200W per channel @ 4Ω and 1,300Wx4 @ 8ohm Power Amplifier, Voltage Gain at 1kHz:38 at 4 ohm, Frequency Response(at 1W, 20Hz to 20kHz into 4 Ω): ± 0.5dB, THD (at 20Hz–20kHz) 0.35% , SNR Analog input>104dB, Damping Factor (20Hz to 100Hz):>1000, CROSS TALK >80dB, Network Control at RJ4 5, DIGITAL SIGNAL PROCESSING : 96kHz, 32-bit floating point, Shall have GPIO port for 3rd party control, Shall have LCD display and signal LED's for input/output, etc complete. MAKE - Crown/L-Acoustics/Promark/D&B

SITC of Compact 2-way Loud speaker with 2x8” LF, 2-way loud speaker system with 1500W Peak,2x8" LFdriver, Coverage Pattern= 120°x60°, Frequency Range=54Hz -20kHz, SPL=120dB, System Sensitivity 1:94dB SPL/1W/1m ,Crossover:2.1kHz, etc complete. MAKE - JBL/L-Acoustics/Promark/D&B

SITC of Wall Mount Bracket for above Loud speaker, Wall Mount kit should be made by same speaker OEM, Should have powder coating, etc complete. MAKE - JBL/L-Acoustics/Promark/D&B.

SITC of 15"Two-Way Stage Monitor and Loud speaker System, Frequency Range(-10dB):55Hz- 19kHz, Frequency Response(±3dB):66Hz- 16kHz ,Coverage Pattern: 90° x50° nominal, Crossover Mode: Passive, Crossover Frequency:2.2kHz, Power Rating: 300W/600W/1200 W, 2hrs (Continuous/Program/Peak), Maximum SPL: 122dB SPL continuous (128dB SPLpeak), System Sensitivity (1w 1m): 98dB SPL, LFDriver: 1x15", HF Driver: 1x1", Nominal Impedance: 8 ohms, Enclosure: Asymmertical, 18 mm, birch/poplar plywood, etc complete. MAKE - JBL/L-Acoustics/Promark/D&B

SITC of Two-way 5.25”speaker with wide 100°x100° coverage, Frequency Response(+/-3dB):85Hz- 17kHz, Power Rating :Continuous 75W (300Wpeak), SPL:116dB, Sensitivity 90dB, 1W/1m, Impedance: 8ohms, Transformer Taps: 100V/70V:30W, 15W, 7.5W, 3.7W 100V:30W, 15W, 7.5W, HighFrequency Driver: 75In, CrossoverType :2nd order low pass, 3rd order high- pass, Outdoor Capability IP-44, Drivers: LF:1x5.25In, HF:1x0.75 in Safety Agency: ROHS-compliant, Transformers UL Recognized per UL1876, High Impact Polystyrene (HIPS) Enclosure, etc complete. MAKE - JBL/L-Acoustics/Promark/D&B

SITC of Two channel, 500W@4Ω Power Amplifier, Voltage Gain:35, Sensitivity (for full rated power at 4Ω):1.4V, Signal-to-Noise Ratio (ref. rated power, 8Ω, 1kHz): >103dB, Total Harmonic Distortion (THD) (1kHz): < 0.5%, Crosstalk (below reated 8ohms power) at 1kHz: >85 db, etc complete. MAKE - Crown/L-Acoustics/Promark/D&B

SITC Wired Gooseneck Microphone with Desktop base unit and on/off switch for Podium, Desktop gooseneck Mic with programmable Function pushtotalk, pushtomute, push on/off, lowcut on/off, Audio frequency bandwidth 70-18000Hz, Polar pattern Cardioid, Max. SPL 125dB (for1%THD), Equivalent noise level<21dB‐A, Signal to Noise:>73dB, Impedance <=600ohms, Recommended load impedance>=2,000ohms, Length500 mm, Voltage 9V to 52V Power Interface, Current 3mA, Connector 3-pin male XLR, etc complete. MAKE - Promark/Shure/Beyer Dynamic/AKG

SITC of Wireless Hand held Microphone System, Wireless Micro phone system with MHZ carrierfrequency band, Upto 16preprogrammed frequencies with in the same frequency band, Audio band width 35- 20,000Hz, THD at 1kHz:<0.3% (Receiver), Signal-to noise: 120dB(A) (Receiver), Wide band FM Modulation, Upto 48 Simultaneous channels, Upto 14 hours operation with one single AA battery or better, Pilot Tone, transmission to know the transmitter battery status, Receivers hould have microphone level and line level output, Transmitter should have display to show the battery and LED to show the Muted/Unmuted status, Sensitivity 6.3 dBV/-100dBm, Should have Micro processor controlled diversity, T.H.D.:0.7% (Transmitter), Infrared programmable, RF output,power: 10 or 50 mW, etc complete. MAKE - Promark/Shure/Beyer Dynamic/AKG

SITC OF Wireless Lavalier Microphone System, Wireless Microphone system with MHZ carrier frequency band, Upto 16 preprogrammed frequencies within the same frequency band,Audiobandwidth35- 20,000Hz,THD at 1kHz:<0.3% (Receiver), Signal-to noise: 120dB(A) (Receiver), Wide band FM Modulation, Up to 48 Simultaneous channels, Upto 14 hours operation with one single AA battery or better, Pilot Tone transmission to know the transmitter battery status, Receiver should have microphone level and line level output, Transmitter should have display to show the battery and LED to show the muted/unmuted status,sensitivity 6.3dB V/100DBM should have microprossesor controled diversity,T.H.D,0.7% (transmitter),infrared programmable,RF output power : 10 or 50 mW etc complete. MAKE - Promark/Shure/Beyer Dynamic/AKG

SITC of Antenna power splitter, Active Antenna Power Splitter for upto 4 receivers, Antenna power splitter with an extended frequency range from 470 to 952 MHZ,Cable lengthadjustmentwithavailable,Support upto 4 receivers etc complete. MAKE - Promark/Shure/Beyer Dynamic/AKG

SITC of Active Omni directional wide band UHF receiving antenna, Switching bandwidth (from/to) : 470 to 952 MHz, Antenna gain 17dBi Cable length can be upto 300M, Covering angle: 360 grid ,recommended load impedande : 50 ohms etc complete MAKE - Promark/Shure/Beyer Dynamic/AKG

SITC of Antenna Booster for Switching bandwidth 470 to 952 MHz, Switching bandwidth (from/to) 470 to 952MHz RF input (50Ohms), Recommended load impedance : 50 Ohms, Can compensate 3.5 to 17.5dB of cable attenuation etc complete MAKE - Promark/Shure/Beyer Dynamic/AKG

SITC of Wired Dynamic Vocal Microphone, Dual shock mount microphone capsule, Super cardioid vocal microphone, Audio frequency bandwidth :70- 20000Hz, Sensitivity 2.6mV/Pa, Electrical impedance: 600Ohms, Recommended loadimpedance:2000Ohms,XLR connector etc complete. MAKE - Promark/Shure/Beyer Dynamic/AKG

SITC of Wired Dynamic Instrument Microphone, Cardioid Dynamic Instrument Microphone, Audiofrequency bandwidth 50- 20000Hz ,Sensitivity at 1000Hz 2.5 mV/Pa(–52dBVre 1V/Pa), Equivalent noise level 18 dBA, Max. SPL for1% THD 147dB SPL, electrical impedance≥ 600ohms ,recommended load impedance ≥ 2000ohms,XLR connctor etc complete MAKE - Promark/Shure/Beyer Dynamic/AKG

SITC of 32Channel Digital mixing console, 32-in/32- out USB Interface, iPadControl ,40-input Mic/Line, 31 Output busses, 8 VCAs+ 8 Mute groups, 26 motorized faders (24 input+LR/Mono), 5" touch screen display, Should Support MADI/Dante/cobranet Cards, 20sub-group/auxbusses, Multi-Color LCD Channel Displays on each etc complete. each input fader ,4stududio -gradeeffect engines and dedicated FX Busses ,4mono/sterio matrix Busses upto 80channels to mix MAKE - Promark/Shure/Beyer Dynamic/Soundcraft/Yamaha/Allen & Heath

SITC of Control Room head phone for FOH Monitoring, Professional studio grade closed back head phones with automute technology, Max. Input Power 200mW, Audio frequency band width=16-28000Hz, Sensitivity headphone =104dB SPL/v,should have detachable cable etc complete. MAKE - Promark/Shure/Beyer Dynamic/AKG

SITC of Powered loud speaker for Monitoring, 5"Two-Way Powered Monitor Speaker, Frequency Range 43Hz-20 kHz, Max PeakSPL 108dB, LFDriver Power Amp41W Class D, HFDriver Power Amp 41W Class D, Input Types :1xXLR,1xTRS Balanced, 1x5" LFDriver ,1x1" HF Driver etc complete. MAKE - JBL/L-Acoustics/Promark/D&B

SITC of 12x8 Networked Digital Signal Processor, DSP with 12 inputs and 8 outputs, 12 Control Inputs and 6 Logic Outputs for GPIO Integration, 48V phantom power on all analog inputs, THD:<0.01%20Hz to 20KHz, +10dBu output, Cross talk: <-75dB, Open architecture software configurable, Separate logic Processing power, 2 digital audio bus RJ45Port, 1 Ethernet port for Monitoring and configuration, Capable to handle + 5V unloaded logic output voltage, at least 6, Should have speech sense engine, Capable to control 3rd party devices with TCPIP and RS232, Should have 1 nos of RS232 port for integration With controle system,should have Bi-directional locate functionality,should have 48 or more digital audio channels bus ,should have monitoring LED for COM,STAT,ERR and PWR etc complete. MAKE - BSS/L-Acoustics/Promark/D&B

SITC of USB Audio to BLU link Interface, 2x2 plug'n'play operation, 48 kHz, 8x8 operation, 48/96kHz etc complete. MAKE - BSS/L-Acoustics/Promark/Cypress/Crestron

SITC of Integrated Controller, Dual Network Interface card, Should support IPv6, Shall Supports IEEE Standard for Port-based Network Access Control with the ability to grant or deny network access to devices wishing to attach to a LAN based on credentialstied to the device rather than to a user, Should have High Performance Architecture, Flexible Programming Platform Java, Should have ability to manage secure port TLS and SSH communications with a remote device or server, Enhanced Diagnostics On Serial and IR Ports, Hardware/Software should be Built for 24/7/365 Operation, Should have Ultra- Fast 1600 MIPS processor, 512MB Onboard RAM, 1M Non-Volatile Memory, 8GB SDHC flash memory,1RU ruck space ,10/100 LAN interface ,for digital I/O ports,1RS-232/422/485 port,3RS-232-only port, 4IR/serial output port ,4relay port, shal be supplied with OEM recommended power supply regulatory complince: RoHS, WEEE etc complete. MAKE - Promark/RGB Spectrum/Extron/AMX/Cypress/Crestron

SITC of 7” Table top Touch Panel, fully configurable, Capacitive Touch Screen, Built in Web Browser and document Viewers, Adjustable Security Modes, Resolution (WH) Landscape :1280x800, Aspect Ratio(WH )Landscape: 16:9, Brightness 330cd/m2, Contrast Ratio 800:1, SD RAM 2GB, Flash 16GB, Ethernet10/100 AutoMDI-X port, RJ-45connector, USB(1) USB host2.0, TypeA ports, Speakers 4ohm, 2Watt, 300Hz cutoff frequency , Supported Video Codecs: MPEG, MPEG-2-TS:H.264, Shall be able to decode two active video streams,viewer applications -PDF,JPEG,BMP,PNG,TIFF,GIF,Power point,DOC,DOX,XLS,XLSX,PPT,PPTX etc complete MAKE - Promark/RGB Spectrum/Extron/AMX/Cypress/Crestron

SITC Of 24 Ports POES with etc complete MAKE - Netgear/Cisco/D-Link

Makin Developers Pvt. Ltd. (BID ID -387154)