DMFT

Drilling of Bore Well by down the hole hammer drilling to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as mediam hard rock formation to hard rock formation,all consolidated formation etc., and drilling in overburdem to dia not less than 200 mm etc., and remaing the bore well to suit insertion of suitable UPVC outer and inner casing pipes etc., including insertion of casing pipe with slotting (with couplilngs,caps any other relevent materials up to required depth as directed by the department including transportion of drilling rigs and supporitng vehicle and including bore development (flusing of bore well at an average pressure of 150 PSI) conducting yield test , consumables charges , crew charges required in fixation of pipe assembly completely done to the satisfaction of depatment and including all labour charges ,the cost of casing pipe,couplings,cap ,Geological survey charges etc.,but excluding taxes .The entire work should be carried out as per IS 2800 part I&II 1979 and amended from time to time. The work is to be carriedout at site/location selected by the department including cost and conveyance of all materials,labour etc, for finished item of work including Over heads and Contractor profit @13.615% but excluding GST .

Supply and Transportation of 5 Star rated Submersible motor pumpsets,confirming ot IS 8034 and Motor confirming to IS 9283 with water proof winding,pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 240 V +/- 10%,Single phase 50 Hz AC supply,etc., complete for Bore well. Makes: Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/AryenVarsha/ Falcon. The work inclusive of all the essential accessories like suction pipe,Valves, Copper cable earthing, end cap, MS clamp, Panel board with standard make etc., The scope including all labour charges, erection charges, cost of all the materials to the extent of departmental satisfaction for finished item of work including Over heads and Contractor profit @13.615% but excluding GST.

Cost, Supply and delivery of HDPE PE-100 6 Kg/Sqcm Pipes as per IS : 4984/2016 including cost and conveyance, excluding taxes etc. complete for 1.00 Rmt. The rate is inclusive of Contractor's Profit @ 13.615 % for pumping main 63mm dia HDPE PE-100 6Kg/cm2

Earth work excavation for pipe line trences (2/3 machinery and 1/3 manual) in all soils except rocky soils including lowering, laying and jointing of pipes with required fittings/specials true to alingment and gradient, refilling with already excavated earth, watering, tamping and removing surplus earth and testing to required hydraulic test pressure etc. complete for finished item of work of 1.00 Rmt of with the rate is inclusive of Contractor's Profit @ 13.615 % for pumping main 63mm dia HDPE PE-100 6Kg/cm2

Construction of 10 KL capacity OHSR of 9.60 mts staging with M30 grade design mix at the site selected by the Department, as per drawings and as specified in Technical Specification including earth work excavation in all types of soils in wet or dry conditions for foundations including cost and conveyance of all materials, cost and fabrication of steel, fixtures, labour charges and testing the reservoir for water tightness etc., complete for finished item of work as per the Standard Specifications and as per the provisions made in the SOR 2022-23. The rate is inclusive of cost of all materials and labour charges and all taxes, duties and levies, etc., complete for finished item of work, but including cost of DI pipes, DI Valves, etc, and excluding GST and Seigniorage charges, including Overheads and Contractors Profit @13.615%.1). All concrete members shall be designed with M30 grade design mix.2) Rate is for OHSRs with RAFT FOUNDATION3) Rate inclusive of three coats of epoxy paint Food Grade of best quality to inner surface of the Reservoir including bottom of roof.4) Rate inclusive of 2 coats of whether proof emulsion painting for external surfaces, lettering, all required fixtures, pipes, bends, valves etc., for pipe connections including cost of pipes, bends and valves as per departmental designs and drawings. 5) The above rates are applicable for basic wind speed of 180 KMPH. Fixtures include :a) RCC or Aluminium ladder inside 0.60 m wide.b) Spiral staircase on the outside shall be provided upto 200 KL.c) Lightening arrestor, including conductor and earthling etc.,d) RCC ventilators with copper or stainless steel fly proof mesh.e) D.I Manholes frame and cover 0.60x0.60m as per IS specifications (light duty) - 2 Nos.f)Water level indicator of good quality with ebonite/copper float of approved pattern-1 No.g) The railing provided to the gallery and staircase shall be with stainless steel of grade 304 for a height of 1.20m. i) D.I swan neck ventilators shall be provided in top dome and slab.j). Bed Blocks of 0.45m x 0.45m x 0.30m in CC M15 Mix below all the duck foot bends k) The rates are inclusive of DI verticals for all inlet, out let, overflow and scour connections( as per estimate diameters) and D.I valves. All valves near inlet, out let and for scour shall be D.I valves of heavy duty conforming to the specification of SoR item No.30

Cost, Supply and delivery of HDPE PE-100 6 Kg/Sqcm Pipes as per IS : 4984/2016 including cost and conveyance, excluding taxes etc. complete for 1.00 Rmt. The rate is inclusive of Contractor's Profit @ 13.615 % for 90mm dia HDPE PE-100 6Kg/cm2

Earth work excavation for pipe line trences (2/3 machinery and 1/3 manual) in all soils except rocky soils including lowering, laying and jointing of pipes with required fittings/specials true to alingment and gradient, refilling with already excavated earth, watering, tamping and removing surplus earth and testing to required hydraulic test pressure etc. complete for finished item of work of 1.00 Rmt of with the rate is inclusive of Contractor's Profit @ 13.615 % for 90mm dia HDPE PE-100 6Kg/cm2

Cost, Supply and delivery of HDPE PE-100 6 Kg/Sqcm Pipes as per IS : 4984/2016 including cost and conveyance, excluding taxes etc. complete for 1.00 Rmt. The rate is inclusive of Contractor's Profit @ 13.615 % for 75mm dia HDPE PE-100 6Kg/cm2

Earth work excavation for pipe line trences (2/3 machinery and 1/3 manual) in all soils except rocky soils including lowering, laying and jointing of pipes with required fittings/specials true to alingment and gradient, refilling with already excavated earth, watering, tamping and removing surplus earth and testing to required hydraulic test pressure etc. complete for finished item of work of 1.00 Rmt of with the rate is inclusive of Contractor's Profit @ 13.615 % for 75mm dia HDPE PE-100 6Kg/cm2

Cost, Supply and delivery of HDPE PE-100 6 Kg/Sqcm Pipes as per IS : 4984/2016 including cost and conveyance, excluding taxes etc. complete for 1.00 Rmt. The rate is inclusive of Contractor's Profit @ 13.615 % for 63mm dia HDPE PE-100 6Kg/cm2

Earth work excavation for pipe line trences (2/3 machinery and 1/3 manual) in all soils except rocky soils including lowering, laying and jointing of pipes with required fittings/specials true to alingment and gradient, refilling with already excavated earth, watering, tamping and removing surplus earth and testing to required hydraulic test pressure etc. complete for finished item of work of 1.00 Rmt of with the rate is inclusive of Contractor's Profit @ 13.615 % for 63mm dia HDPE PE-100 6Kg/cm2

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, but excluding GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Supply and fixing of 110mm dia PVC 4kg/sqm pipe cost and conveyance of all material and labour charges etc. Complete

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Supply & Fixing of Name Board The rates are inclusive of cost and conveyance of all materials and labour charges for finished item, but excluding GST and seignourage charges etc., Complete

Drilling of Bore Well by down the hole hammer drilling to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as mediam hard rock formation to hard rock formation,all consolidated formation etc., and drilling in overburdem to dia not less than 200 mm etc., and remaing the bore well to suit insertion of suitable UPVC outer and inner casing pipes etc., including insertion of casing pipe with slotting (with couplilngs,caps any other relevent materials up to required depth as directed by the department including transportion of drilling rigs and supporitng vehicle and including bore development (flusing of bore well at an average pressure of 150 PSI) conducting yield test , consumables charges , crew charges required in fixation of pipe assembly completely done to the satisfaction of depatment and including all labour charges ,the cost of casing pipe,couplings,cap ,Geological survey charges etc.,but excluding taxes .The entire work should be carried out as per IS 2800 part I&II 1979 and amended from time to time. The work is to be carriedout at site/location selected by the department including cost and conveyance of all materials,labour etc, for finished item of work including Over heads and Contractor profit @13.615% but excluding GST .

Supply and Transportation of 5 Star rated Submersible motor pumpsets,confirming ot IS 8034 and Motor confirming to IS 9283 with water proof winding,pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 240 V +/- 10%,Single phase 50 Hz AC supply,etc., complete for Bore well. Makes: Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/AryenVarsha/ Falcon. The work inclusive of all the essential accessories like suction pipe,Valves, Copper cable earthing, end cap, MS clamp, Panel board with standard make etc., The scope including all labour charges, erection charges, cost of all the materials to the extent of departmental satisfaction for finished item of work including Over heads and Contractor profit @13.615% but excluding GST.

Construction of 15 KL capacity OHSR of 9.40 mts staging at Gunkalam Village with M30 grade design mix at the site selected by the Department, as per drawings and as specified in Technical Specification including earth work excavation in all types of soils in wet or dry conditions for foundations including cost and conveyance of all materials, cost and fabrication of steel, fixtures, labour charges and testing the reservoir for water tightness etc., complete for finished item of work as per the Standard Specifications and as per the provisions made in the SOR 2022-23. The rate is inclusive of cost of all materials and labour charges and all taxes, duties and levies, etc., complete for finished item of work, but including cost of DI pipes, DI Valves, etc, and excluding GST and Seigniorage charges, including Overheads and Contractors Profit @13.615%. 1). All concrete members shall be designed with M30 grade design mix. 2) Rate is for OHSRs with RAFT FOUNDATION 3) Rate inclusive of three coats of epoxy paint Food Grade of best quality to inner surface of the Reservoir including bottom of roof. 4) Rate inclusive of 2 coats of whether proof emulsion painting for external surfaces, lettering, all required fixtures, pipes, bends, valves etc., for pipe connections including cost of pipes, bends and valves as per departmental designs and drawings. 5) The above rates are applicable for basic wind speed of 180 KMPH . Fixtures include : a) RCC or Aluminium ladder inside 0.60 m wide. b) Spiral staircase on the outside shall be provided upto 200 KL. c) Lightening arrestor, including conductor and earthling etc.,d) RCC ventilators with copper or stainless steel fly proof mesh. e) D.I Manholes frame and cover 0.60x0.60m as per IS specifications (light duty) - 2 Nos. f)Water level indicator of good quality with ebonite/copper float of approved pattern-1 No. g) The railing provided to the gallery and staircase shall be with stainless steel of grade 304 for a height of 1.20m. i) D.I swan neck ventilators shall be provided in top dome and slab. j). Bed Blocks of 0.45m x 0.45m x 0.30m in CC M15 Mix below all the duck foot bends k) The rates are inclusive of DI verticals for all inlet, out let, overflow and scour connections( as per estimate diameters) and D.I valves. All valves near inlet, out let and for scour shall be D.I valves of heavy duty conforming to the specification of SoR item No.30

Construction of pipelines for water supply with 63mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 75mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 90mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 110mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 160 mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 180mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 75 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 90 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 110 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 180 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of pipelines for water supply with 63mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 75mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 90mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 110mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 140 mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 160 mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 180mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 75 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 90 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Drilling of Bore Well by down the hole hammer drilling to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as mediam hard rock formation to hard rock formation,all consolidated formation etc., and drilling in overburdem to dia not less than 200 mm etc., and remaing the bore well to suit insertion of suitable UPVC outer and inner casing pipes etc., including insertion of casing pipe with slotting (with couplilngs,caps any other relevent materials up to required depth as directed by the department including transportion of drilling rigs and supporitng vehicle and including bore development (flusing of bore well at an average pressure of 150 PSI) conducting yield test , consumables charges , crew charges required in fixation of pipe assembly completely done to the satisfaction of depatment and including all labour charges ,the cost of casing pipe,couplings,cap ,Geological survey charges etc.,but excluding taxes .The entire work should be carried out as per IS 2800 part I&II 1979 and amended from time to time. The work is to be carriedout at site/location selected by the department including cost and conveyance of all materials,labour etc, for finished item of work including Over heads and Contractor profit @13.615% but excluding GST .

Supply and Transportation of 5 Star rated Submersible motor pumpsets,confirming ot IS 8034 and Motor confirming to IS 9283 with water proof winding,pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 240 V +/- 10%,Single phase 50 Hz AC supply,etc., complete for Bore well. Makes: Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/AryenVarsha/ Falcon. The work inclusive of all the essential accessories like suction pipe,Valves, Copper cable earthing, end cap, MS clamp, Panel board with standard make etc., The scope including all labour charges, erection charges, cost of all the materials to the extent of departmental satisfaction for finished item of work including Over heads and Contractor profit @13.615% but excluding GST.

Construction of 30 KL capacity OHSR of 9.40 mts staging at Rakodu Village with M30 grade design mix at the site selected by the Department, as per drawings and as specified in Technical Specification including earth work excavation in all types of soils in wet or dry conditions for foundations including cost and conveyance of all materials, cost and fabrication of steel, fixtures, labour charges and testing the reservoir for water tightness etc., complete for finished item of work as per the Standard Specifications and as per the provisions made in the SOR 2022-23. The rate is inclusive of cost of all materials and labour charges and all taxes, duties and levies, etc., complete for finished item of work, but including cost of DI pipes, DI Valves, etc, and excluding GST and Seigniorage charges, including Overheads and Contractors Profit @13.615%. 1). All concrete members shall be designed with M30 grade design mix. 2) Rate is for OHSRs with RAFT FOUNDATION 3) Rate inclusive of three coats of epoxy paint Food Grade of best quality to inner surface of the Reservoir including bottom of roof. 4) Rate inclusive of 2 coats of whether proof emulsion painting for external surfaces, lettering, all required fixtures, pipes, bends, valves etc., for pipe connections including cost of pipes, bends and valves as per departmental designs and drawings. 5) The above rates are applicable for basic wind speed of 180 KMPH . Fixtures include : a) RCC or Aluminium ladder inside 0.60 m wide. b) Spiral staircase on the outside shall be provided upto 200 KL. c) Lightening arrestor, including conductor and earthling etc.,d) RCC ventilators with copper or stainless steel fly proof mesh. e) D.I Manholes frame and cover 0.60x0.60m as per IS specifications (light duty) - 2 Nos. f)Water level indicator of good quality with ebonite/copper float of approved pattern-1 No. g) The railing provided to the gallery and staircase shall be with stainless steel of grade 304 for a height of 1.20m. i) D.I swan neck ventilators shall be provided in top dome and slab. j). Bed Blocks of 0.45m x 0.45m x 0.30m in CC M15 Mix below all the duck foot bends k) The rates are inclusive of DI verticals for all inlet, out let, overflow and scour connections( as per estimate diameters) and D.I valves. All valves near inlet, out let and for scour shall be D.I valves of heavy duty conforming to the specification of SoR item No.30

Construction of pipelines for water supply with 63mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 75mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 90mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 75 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 90 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Drilling of Bore Well by down the hole hammer drilling to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as mediam hard rock formation to hard rock formation,all consolidated formation etc., and drilling in overburdem to dia not less than 200 mm etc., and remaing the bore well to suit insertion of suitable UPVC outer and inner casing pipes etc., including insertion of casing pipe with slotting (with couplilngs,caps any other relevent materials up to required depth as directed by the department including transportion of drilling rigs and supporitng vehicle and including bore development (flusing of bore well at an average pressure of 150 PSI) conducting yield test , consumables charges , crew charges required in fixation of pipe assembly completely done to the satisfaction of depatment and including all labour charges ,the cost of casing pipe,couplings,cap ,Geological survey charges etc.,but excluding taxes .The entire work should be carried out as per IS 2800 part I&II 1979 and amended from time to time. The work is to be carriedout at site/location selected by the department including cost and conveyance of all materials,labour etc, for finished item of work including Over heads and Contractor profit @13.615% but excluding GST .

Supply and Transportation of 5 Star rated Submersible motor pumpsets,confirming ot IS 8034 and Motor confirming to IS 9283 with water proof winding,pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 415 V +/- 10%,Three phase 50 Hz AC supply,etc., complete for Bore well. Makes: Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/AryenVarsha/ Falcon. The work inclusive of all the essential accessories like suction pipe,Valves, Copper cable earthing, end cap, MS clamp, Panel board with standard make etc., The scope including all labour charges, erection charges, cost of all the materials to the extent of departmental satisfaction for finished item of work including Over heads and Contractor profit @13.615% but excluding GST.

Construction of 60 KL capacity OHSR of 12.95 mts staging at Narayanapuram Village with M30 grade design mix at the site selected by the Department, as per drawings and as specified in Technical Specification including earth work excavation in all types of soils in wet or dry conditions for foundations including cost and conveyance of all materials, cost and fabrication of steel, fixtures, labour charges and testing the reservoir for water tightness etc., complete for finished item of work as per the Standard Specifications and as per the provisions made in the SOR 2022-23. The rate is inclusive of cost of all materials and labour charges and all taxes, duties and levies, etc., complete for finished item of work, but including cost of DI pipes, DI Valves, etc, and excluding GST and Seigniorage charges, including Overheads and Contractors Profit @13.615%. 1). All concrete members shall be designed with M30 grade design mix. 2) Rate is for OHSRs with RAFT FOUNDATION 3) Rate inclusive of three coats of epoxy paint Food Grade of best quality to inner surface of the Reservoir including bottom of roof. 4) Rate inclusive of 2 coats of whether proof emulsion painting for external surfaces, lettering, all required fixtures, pipes, bends, valves etc., for pipe connections including cost of pipes, bends and valves as per departmental designs and drawings. 5) The above rates are applicable for basic wind speed of 180 KMPH . Fixtures include : a) RCC or Aluminium ladder inside 0.60 m wide. b) Spiral staircase on the outside shall be provided upto 200 KL. c) Lightening arrestor, including conductor and earthling etc.,d) RCC ventilators with copper or stainless steel fly proof mesh. e) D.I Manholes frame and cover 0.60x0.60m as per IS specifications (light duty) - 2 Nos. f)Water level indicator of good quality with ebonite/copper float of approved pattern-1 No. g) The railing provided to the gallery and staircase shall be with stainless steel of grade 304 for a height of 1.20m. i) D.I swan neck ventilators shall be provided in top dome and slab. j). Bed Blocks of 0.45m x 0.45m x 0.30m in CC M15 Mix below all the duck foot bends k) The rates are inclusive of DI verticals for all inlet, out let, overflow and scour connections( as per estimate diameters) and D.I valves. All valves near inlet, out let and for scour shall be D.I valves of heavy duty conforming to the specification of SoR item No.30

Construction of pipelines for water supply with 63mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 75mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 90mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 110mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 140 mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 75 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 90 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Drilling of Bore Well by down the hole hammer drilling to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as mediam hard rock formation to hard rock formation,all consolidated formation etc., and drilling in overburdem to dia not less than 200 mm etc., and remaing the bore well to suit insertion of suitable UPVC outer and inner casing pipes etc., including insertion of casing pipe with slotting (with couplilngs,caps any other relevent materials up to required depth as directed by the department including transportion of drilling rigs and supporitng vehicle and including bore development (flusing of bore well at an average pressure of 150 PSI) conducting yield test , consumables charges , crew charges required in fixation of pipe assembly completely done to the satisfaction of depatment and including all labour charges ,the cost of casing pipe,couplings,cap ,Geological survey charges etc.,but excluding taxes .The entire work should be carried out as per IS 2800 part I&II 1979 and amended from time to time. The work is to be carriedout at site/location selected by the department including cost and conveyance of all materials,labour etc, for finished item of work including Over heads and Contractor profit @13.615% but excluding GST .

Supply and Transportation of 5 Star rated Submersible motor pumpsets,confirming ot IS 8034 and Motor confirming to IS 9283 with water proof winding,pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 240 V +/- 10%,Single phase 50 Hz AC supply,etc., complete for Bore well. Makes: Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/AryenVarsha/ Falcon. The work inclusive of all the essential accessories like suction pipe,Valves, Copper cable earthing, end cap, MS clamp, Panel board with standard make etc., The scope including all labour charges, erection charges, cost of all the materials to the extent of departmental satisfaction for finished item of work including Over heads and Contractor profit @13.615% but excluding GST.

Construction of 40 KL capacity OHSR of 12.90 mts staging at Mudidam Village with M30 grade design mix at the site selected by the Department, as per drawings and as specified in Technical Specification including earth work excavation in all types of soils in wet or dry conditions for foundations including cost and conveyance of all materials, cost and fabrication of steel, fixtures, labour charges and testing the reservoir for water tightness etc., complete for finished item of work as per the Standard Specifications and as per the provisions made in the SOR 2022-23. The rate is inclusive of cost of all materials and labour charges and all taxes, duties and levies, etc., complete for finished item of work, but including cost of DI pipes, DI Valves, etc, and excluding GST and Seigniorage charges, including Overheads and Contractors Profit @13.615%. 1). All concrete members shall be designed with M30 grade design mix. 2) Rate is for OHSRs with RAFT FOUNDATION 3) Rate inclusive of three coats of epoxy paint Food Grade of best quality to inner surface of the Reservoir including bottom of roof. 4) Rate inclusive of 2 coats of whether proof emulsion painting for external surfaces, lettering, all required fixtures, pipes, bends, valves etc., for pipe connections including cost of pipes, bends and valves as per departmental designs and drawings. 5) The above rates are applicable for basic wind speed of 180 KMPH . Fixtures include : a) RCC or Aluminium ladder inside 0.60 m wide. b) Spiral staircase on the outside shall be provided upto 200 KL. c) Lightening arrestor, including conductor and earthling etc.,d) RCC ventilators with copper or stainless steel fly proof mesh. e) D.I Manholes frame and cover 0.60x0.60m as per IS specifications (light duty) - 2 Nos. f)Water level indicator of good quality with ebonite/copper float of approved pattern-1 No. g) The railing provided to the gallery and staircase shall be with stainless steel of grade 304 for a height of 1.20m. i) D.I swan neck ventilators shall be provided in top dome and slab. j). Bed Blocks of 0.45m x 0.45m x 0.30m in CC M15 Mix below all the duck foot bends k) The rates are inclusive of DI verticals for all inlet, out let, overflow and scour connections( as per estimate diameters) and D.I valves. All valves near inlet, out let and for scour shall be D.I valves of heavy duty conforming to the specification of SoR item No.30

Construction of pipelines for water supply with 63mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 75mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 90mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 110mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 75 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 90 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 110 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of pipelines for water supply with 63mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 75mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 90mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply ,Supply & Fixing 80mm Nominal Bore GI pipe Medium Grade properties & weight as per IS 1239 with GI fittings such as elbows tees couplings, nipples, plugs including excavation for trenches and refilling the trenches complete except for GI bends union and GI connectors with checkout and socket Tata or Zenith make or equivalent. with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical Specifications (Part-B, Volume-I) . The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and Seigniorge charges, including overheads and Contractor's profit @ 13.615%

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 75 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 90 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 110 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Drilling of Bore Well by down the hole hammer drilling to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as mediam hard rock formation to hard rock formation,all consolidated formation etc., and drilling in overburdem to dia not less than 200 mm etc., and remaing the bore well to suit insertion of suitable UPVC outer and inner casing pipes etc., including insertion of casing pipe with slotting (with couplilngs,caps any other relevent materials up to required depth as directed by the department including transportion of drilling rigs and supporitng vehicle and including bore development (flusing of bore well at an average pressure of 150 PSI) conducting yield test , consumables charges , crew charges required in fixation of pipe assembly completely done to the satisfaction of depatment and including all labour charges ,the cost of casing pipe,couplings,cap ,Geological survey charges etc.,but excluding taxes .The entire work should be carried out as per IS 2800 part I&II 1979 and amended from time to time. The work is to be carriedout at site/location selected by the department including cost and conveyance of all materials,labour etc, for finished item of work including Over heads and Contractor profit @13.615% but excluding GST .

Supply and Transportation of 5 Star rated Submersible motor pumpsets,confirming ot IS 8034 and Motor confirming to IS 9283 with water proof winding,pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 240 V +/- 10%,Single phase 50 Hz AC supply,etc., complete for Bore well. Makes: Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/AryenVarsha/ Falcon. The work inclusive of all the essential accessories like suction pipe,Valves, Copper cable earthing, end cap, MS clamp, Panel board with standard make etc., The scope including all labour charges, erection charges, cost of all the materials to the extent of departmental satisfaction for finished item of work including Over heads and Contractor profit @13.615% but excluding GST.

Construction of 90 KL capacity OHSR of 9.40 mts staging at Padalapeta Village with 12.90 m staging and M30 grade design mix at the site selected by the Department, as per drawings and as specified in Technical Specification including earth work excavation in all types of soils in wet or dry conditions for foundations including cost and conveyance of all materials, cost and fabrication of steel, fixtures, labour charges and testing the reservoir for water tightness etc., complete for finished item of work as per the Standard Specifications and as per the provisions made in the SOR 2022-23. The rate is inclusive of cost of all materials and labour charges and all taxes, duties and levies, etc., complete for finished item of work, but including cost of DI pipes, DI Valves, etc, and excluding GST and Seigniorage charges, including Overheads and Contractors Profit @13.615%. 1). All concrete members shall be designed with M30 grade design mix. 2) Rate is for OHSRs with RAFT FOUNDATION 3) Rate inclusive of three coats of epoxy paint Food Grade of best quality to inner surface of the Reservoir including bottom of roof. 4) Rate inclusive of 2 coats of whether proof emulsion painting for external surfaces, lettering, all required fixtures, pipes, bends, valves etc., for pipe connections including cost of pipes, bends and valves as per departmental designs and drawings. 5) The above rates are applicable for basic wind speed of 180 KMPH . Fixtures include : a) RCC or Aluminium ladder inside 0.60 m wide. b) Spiral staircase on the outside shall be provided upto 200 KL. c) Lightening arrestor, including conductor and earthling etc.,d) RCC ventilators with copper or stainless steel fly proof mesh. e) D.I Manholes frame and cover 0.60x0.60m as per IS specifications (light duty) - 2 Nos. f)Water level indicator of good quality with ebonite/copper float of approved pattern-1 No. g) The railing provided to the gallery and staircase shall be with stainless steel of grade 304 for a height of 1.20m. i) D.I swan neck ventilators shall be provided in top dome and slab. j). Bed Blocks of 0.45m x 0.45m x 0.30m in CC M15 Mix below all the duck foot bends k) The rates are inclusive of DI verticals for all inlet, out let, overflow and scour connections( as per estimate diameters) and D.I valves. All valves near inlet, out let and for scour shall be D.I valves of heavy duty conforming to the specification of SoR item No.30

Construction of pipelines for water supply with 63mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Drilling of Bore Well by down the hole hammer drilling to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as mediam hard rock formation to hard rock formation,all consolidated formation etc., and drilling in overburdem to dia not less than 200 mm etc., and remaing the bore well to suit insertion of suitable UPVC outer and inner casing pipes etc., including insertion of casing pipe with slotting (with couplilngs,caps any other relevent materials up to required depth as directed by the department including transportion of drilling rigs and supporitng vehicle and including bore development (flusing of bore well at an average pressure of 150 PSI) conducting yield test , consumables charges , crew charges required in fixation of pipe assembly completely done to the satisfaction of depatment and including all labour charges ,the cost of casing pipe,couplings,cap ,Geological survey charges etc.,but excluding taxes .The entire work should be carried out as per IS 2800 part I&II 1979 and amended from time to time. The work is to be carriedout at site/location selected by the department including cost and conveyance of all materials,labour etc, for finished item of work including Over heads and Contractor profit @13.615% but excluding GST .

Supply and Transportation of 5 Star rated Submersible motor pumpsets,confirming ot IS 8034 and Motor confirming to IS 9283 with water proof winding,pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 415 V +/- 10%,Three phase 50 Hz AC supply,etc., complete for Bore well. Makes: Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/AryenVarsha/ Falcon. The work inclusive of all the essential accessories like suction pipe,Valves, Copper cable earthing, end cap, MS clamp, Panel board with standard make etc., The scope including all labour charges, erection charges, cost of all the materials to the extent of departmental satisfaction for finished item of work including Over heads and Contractor profit @13.615% but excluding GST.

Construction of 60 KL capacity OHSR of 12.95 mts staging at Korukonda Village with M30 grade design mix at the site selected by the Department, as per drawings and as specified in Technical Specification including earth work excavation in all types of soils in wet or dry conditions for foundations including cost and conveyance of all materials, cost and fabrication of steel, fixtures, labour charges and testing the reservoir for water tightness etc., complete for finished item of work as per the Standard Specifications and as per the provisions made in the SOR 2022-23. The rate is inclusive of cost of all materials and labour charges and all taxes, duties and levies, etc., complete for finished item of work, but including cost of DI pipes, DI Valves, etc, and excluding GST and Seigniorage charges, including Overheads and Contractors Profit @13.615%. 1). All concrete members shall be designed with M30 grade design mix. 2) Rate is for OHSRs with RAFT FOUNDATION 3) Rate inclusive of three coats of epoxy paint Food Grade of best quality to inner surface of the Reservoir including bottom of roof. 4) Rate inclusive of 2 coats of whether proof emulsion painting for external surfaces, lettering, all required fixtures, pipes, bends, valves etc., for pipe connections including cost of pipes, bends and valves as per departmental designs and drawings. 5) The above rates are applicable for basic wind speed of 180 KMPH . Fixtures include : a) RCC or Aluminium ladder inside 0.60 m wide. b) Spiral staircase on the outside shall be provided upto 200 KL. c) Lightening arrestor, including conductor and earthling etc.,d) RCC ventilators with copper or stainless steel fly proof mesh. e) D.I Manholes frame and cover 0.60x0.60m as per IS specifications (light duty) - 2 Nos. f)Water level indicator of good quality with ebonite/copper float of approved pattern-1 No. g) The railing provided to the gallery and staircase shall be with stainless steel of grade 304 for a height of 1.20m. i) D.I swan neck ventilators shall be provided in top dome and slab. j). Bed Blocks of 0.45m x 0.45m x 0.30m in CC M15 Mix below all the duck foot bends k) The rates are inclusive of DI verticals for all inlet, out let, overflow and scour connections( as per estimate diameters) and D.I valves. All valves near inlet, out let and for scour shall be D.I valves of heavy duty conforming to the specification of SoR item No.30

Construction of pipelines for water supply with 63mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 110mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 75 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 90 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Drilling of Bore Well by down the hole hammer drilling to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as mediam hard rock formation to hard rock formation,all consolidated formation etc., and drilling in overburdem to dia not less than 200 mm etc., and remaing the bore well to suit insertion of suitable UPVC outer and inner casing pipes etc., including insertion of casing pipe with slotting (with couplilngs,caps any other relevent materials up to required depth as directed by the department including transportion of drilling rigs and supporitng vehicle and including bore development (flusing of bore well at an average pressure of 150 PSI) conducting yield test , consumables charges , crew charges required in fixation of pipe assembly completely done to the satisfaction of depatment and including all labour charges ,the cost of casing pipe,couplings,cap ,Geological survey charges etc.,but excluding taxes .The entire work should be carried out as per IS 2800 part I&II 1979 and amended from time to time. The work is to be carriedout at site/location selected by the department including cost and conveyance of all materials,labour etc, for finished item of work including Over heads and Contractor profit @13.615% but excluding GST .

Supply and Transportation of 5 Star rated Submersible motor pumpsets,confirming ot IS 8034 and Motor confirming to IS 9283 with water proof winding,pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 415 V +/- 10%,Three phase 50 Hz AC supply,etc., complete for Bore well. Makes: Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/AryenVarsha/ Falcon. The work inclusive of all the essential accessories like suction pipe,Valves, Copper cable earthing, end cap, MS clamp, Panel board with standard make etc., The scope including all labour charges, erection charges, cost of all the materials to the extent of departmental satisfaction for finished item of work including Over heads and Contractor profit @13.615% but excluding GST.

Construction of 40 KL capacity OHSR of 12.90 mts staging at Kondakarakam Village with M30 grade design mix at the site selected by the Department, as per drawings and as specified in Technical Specification including earth work excavation in all types of soils in wet or dry conditions for foundations including cost and conveyance of all materials, cost and fabrication of steel, fixtures, labour charges and testing the reservoir for water tightness etc., complete for finished item of work as per the Standard Specifications and as per the provisions made in the SOR 2022-23. The rate is inclusive of cost of all materials and labour charges and all taxes, duties and levies, etc., complete for finished item of work, but including cost of DI pipes, DI Valves, etc, and excluding GST and Seigniorage charges, including Overheads and Contractors Profit @13.615%. 1). All concrete members shall be designed with M30 grade design mix. 2) Rate is for OHSRs with RAFT FOUNDATION 3) Rate inclusive of three coats of epoxy paint Food Grade of best quality to inner surface of the Reservoir including bottom of roof. 4) Rate inclusive of 2 coats of whether proof emulsion painting for external surfaces, lettering, all required fixtures, pipes, bends, valves etc., for pipe connections including cost of pipes, bends and valves as per departmental designs and drawings. 5) The above rates are applicable for basic wind speed of 180 KMPH . Fixtures include : a) RCC or Aluminium ladder inside 0.60 m wide. b) Spiral staircase on the outside shall be provided upto 200 KL. c) Lightening arrestor, including conductor and earthling etc.,d) RCC ventilators with copper or stainless steel fly proof mesh. e) D.I Manholes frame and cover 0.60x0.60m as per IS specifications (light duty) - 2 Nos. f)Water level indicator of good quality with ebonite/copper float of approved pattern-1 No. g) The railing provided to the gallery and staircase shall be with stainless steel of grade 304 for a height of 1.20m. i) D.I swan neck ventilators shall be provided in top dome and slab. j). Bed Blocks of 0.45m x 0.45m x 0.30m in CC M15 Mix below all the duck foot bends k) The rates are inclusive of DI verticals for all inlet, out let, overflow and scour connections( as per estimate diameters) and D.I valves. All valves near inlet, out let and for scour shall be D.I valves of heavy duty conforming to the specification of SoR item No.30

Construction of pipelines for water supply with 63mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 75mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 90mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 110mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 160 mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 250 mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 75 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 90 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Drilling of Bore Well by down the hole hammer drilling to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as mediam hard rock formation to hard rock formation,all consolidated formation etc., and drilling in overburdem to dia not less than 200 mm etc., and remaing the bore well to suit insertion of suitable UPVC outer and inner casing pipes etc., including insertion of casing pipe with slotting (with couplilngs,caps any other relevent materials up to required depth as directed by the department including transportion of drilling rigs and supporitng vehicle and including bore development (flusing of bore well at an average pressure of 150 PSI) conducting yield test , consumables charges , crew charges required in fixation of pipe assembly completely done to the satisfaction of depatment and including all labour charges ,the cost of casing pipe,couplings,cap ,Geological survey charges etc.,but excluding taxes .The entire work should be carried out as per IS 2800 part I&II 1979 and amended from time to time. The work is to be carriedout at site/location selected by the department including cost and conveyance of all materials,labour etc, for finished item of work including Over heads and Contractor profit @13.615% but excluding GST .

Supply and Transportation of 5 Star rated Submersible motor pumpsets,confirming ot IS 8034 and Motor confirming to IS 9283 with water proof winding,pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 240 V +/- 10%,Single phase 50 Hz AC supply,etc., complete for Bore well. Makes: Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/AryenVarsha/ Falcon. The work inclusive of all the essential accessories like suction pipe,Valves, Copper cable earthing, end cap, MS clamp, Panel board with standard make etc., The scope including all labour charges, erection charges, cost of all the materials to the extent of departmental satisfaction for finished item of work including Over heads and Contractor profit @13.615% but excluding GST.

Construction of 60 KL capacity OHSR of 12.95 mts staging at Reemapeta Village with M30 grade design mix at the site selected by the Department, as per drawings and as specified in Technical Specification including earth work excavation in all types of soils in wet or dry conditions for foundations including cost and conveyance of all materials, cost and fabrication of steel, fixtures, labour charges and testing the reservoir for water tightness etc., complete for finished item of work as per the Standard Specifications and as per the provisions made in the SOR 2022-23. The rate is inclusive of cost of all materials and labour charges and all taxes, duties and levies, etc., complete for finished item of work, but including cost of DI pipes, DI Valves, etc, and excluding GST and Seigniorage charges, including Overheads and Contractors Profit @13.615%. 1). All concrete members shall be designed with M30 grade design mix. 2) Rate is for OHSRs with RAFT FOUNDATION 3) Rate inclusive of three coats of epoxy paint Food Grade of best quality to inner surface of the Reservoir including bottom of roof. 4) Rate inclusive of 2 coats of whether proof emulsion painting for external surfaces, lettering, all required fixtures, pipes, bends, valves etc., for pipe connections including cost of pipes, bends and valves as per departmental designs and drawings. 5) The above rates are applicable for basic wind speed of 180 KMPH . Fixtures include : a) RCC or Aluminium ladder inside 0.60 m wide. b) Spiral staircase on the outside shall be provided upto 200 KL. c) Lightening arrestor, including conductor and earthling etc.,d) RCC ventilators with copper or stainless steel fly proof mesh. e) D.I Manholes frame and cover 0.60x0.60m as per IS specifications (light duty) - 2 Nos. f)Water level indicator of good quality with ebonite/copper float of approved pattern-1 No. g) The railing provided to the gallery and staircase shall be with stainless steel of grade 304 for a height of 1.20m. i) D.I swan neck ventilators shall be provided in top dome and slab. j). Bed Blocks of 0.45m x 0.45m x 0.30m in CC M15 Mix below all the duck foot bends k) The rates are inclusive of DI verticals for all inlet, out let, overflow and scour connections( as per estimate diameters) and D.I valves. All valves near inlet, out let and for scour shall be D.I valves of heavy duty conforming to the specification of SoR item No.30

Construction of pipelines for water supply with 63mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 75mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 90mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 110mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 140 mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 75 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 90 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 110 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of pipelines for water supply with 63mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 75mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 90mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 110mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 140 mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 180mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply ,Supply & Fixing 50 mm Nominal Bore GI pipe Medium Grade properties & weight as per IS 1239 with GI fittings such as elbows tees couplings, nipples, plugs including excavation for trenches and refilling the trenches complete except for GI bends union and GI connectors with checkout and socket Tata or Zenith make or equivalent. with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical Specifications (Part-B, Volume-I) . The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and Seigniorge charges, including overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply ,Supply & Fixing 50 mm Nominal Bore GI pipe Medium Grade properties & weight as per IS 1239 with GI fittings such as elbows tees couplings, nipples, plugs including excavation for trenches and refilling the trenches complete except for GI bends union and GI connectors with checkout and socket Tata or Zenith make or equivalent. with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical Specifications (Part-B, Volume-I) . The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and Seigniorge charges, including overheads and Contractor's profit @ 13.615%

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 75 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 90 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 110 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Supply and Transportation of 5 Star rated Submersible motor pumpsets,confirming ot IS 8034 and Motor confirming to IS 9283 with water proof winding,pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 240 V +/- 10%,Single phase 50 Hz AC supply,etc., complete for Bore well. Makes: Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/AryenVarsha/ Falcon. The work inclusive of all the essential accessories like suction pipe,Valves, Copper cable earthing, end cap, MS clamp, Panel board with standard make etc., The scope including all labour charges, erection charges, cost of all the materials to the extent of departmental satisfaction for finished item of work including Over heads and Contractor profit @13.615% but excluding GST.

Construction of 30 KL capacity OHSR of 12.75 mts staging at Korukondapalem Village with M30 grade design mix at the site selected by the Department, as per drawings and as specified in Technical Specification including earth work excavation in all types of soils in wet or dry conditions for foundations including cost and conveyance of all materials, cost and fabrication of steel, fixtures, labour charges and testing the reservoir for water tightness etc., complete for finished item of work as per the Standard Specifications and as per the provisions made in the SOR 2022-23. The rate is inclusive of cost of all materials and labour charges and all taxes, duties and levies, etc., complete for finished item of work, but including cost of DI pipes, DI Valves, etc, and excluding GST and Seigniorage charges, including Overheads and Contractors Profit @13.615%. 1). All concrete members shall be designed with M30 grade design mix. 2) Rate is for OHSRs with RAFT FOUNDATION 3) Rate inclusive of three coats of epoxy paint Food Grade of best quality to inner surface of the Reservoir including bottom of roof. 4) Rate inclusive of 2 coats of whether proof emulsion painting for external surfaces, lettering, all required fixtures, pipes, bends, valves etc., for pipe connections including cost of pipes, bends and valves as per departmental designs and drawings. 5) The above rates are applicable for basic wind speed of 180 KMPH . Fixtures include : a) RCC or Aluminium ladder inside 0.60 m wide. b) Spiral staircase on the outside shall be provided upto 200 KL. c) Lightening arrestor, including conductor and earthling etc.,d) RCC ventilators with copper or stainless steel fly proof mesh. e) D.I Manholes frame and cover 0.60x0.60m as per IS specifications (light duty) - 2 Nos. f)Water level indicator of good quality with ebonite/copper float of approved pattern-1 No. g) The railing provided to the gallery and staircase shall be with stainless steel of grade 304 for a height of 1.20m. i) D.I swan neck ventilators shall be provided in top dome and slab. j). Bed Blocks of 0.45m x 0.45m x 0.30m in CC M15 Mix below all the duck foot bends k) The rates are inclusive of DI verticals for all inlet, out let, overflow and scour connections( as per estimate diameters) and D.I valves. All valves near inlet, out let and for scour shall be D.I valves of heavy duty conforming to the specification of SoR item No.30

Construction of pipelines for water supply with 63mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 75mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 90mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 75 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 90 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Drilling of Bore Well by down the hole hammer drilling to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as mediam hard rock formation to hard rock formation,all consolidated formation etc., and drilling in overburdem to dia not less than 200 mm etc., and remaing the bore well to suit insertion of suitable UPVC outer and inner casing pipes etc., including insertion of casing pipe with slotting (with couplilngs,caps any other relevent materials up to required depth as directed by the department including transportion of drilling rigs and supporitng vehicle and including bore development (flusing of bore well at an average pressure of 150 PSI) conducting yield test , consumables charges , crew charges required in fixation of pipe assembly completely done to the satisfaction of depatment and including all labour charges ,the cost of casing pipe,couplings,cap ,Geological survey charges etc.,but excluding taxes .The entire work should be carried out as per IS 2800 part I&II 1979 and amended from time to time. The work is to be carriedout at site/location selected by the department including cost and conveyance of all materials,labour etc, for finished item of work including Over heads and Contractor profit @13.615% but excluding GST .

Supply and Transportation of 5 Star rated Submersible motor pumpsets,confirming ot IS 8034 and Motor confirming to IS 9283 with water proof winding,pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 240 V +/- 10%,Single phase 50 Hz AC supply,etc., complete for Bore well. Makes: Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/AryenVarsha/ Falcon. The work inclusive of all the essential accessories like suction pipe,Valves, Copper cable earthing, end cap, MS clamp, Panel board with standard make etc., The scope including all labour charges, erection charges, cost of all the materials to the extent of departmental satisfaction for finished item of work including Over heads and Contractor profit @13.615% but excluding GST.

Construction of 10 KL capacity OHSR of 9.40 mts staging at Koradapeta Village with M30 grade design mix at the site selected by the Department, as per drawings and as specified in Technical Specification including earth work excavation in all types of soils in wet or dry conditions for foundations including cost and conveyance of all materials, cost and fabrication of steel, fixtures, labour charges and testing the reservoir for water tightness etc., complete for finished item of work as per the Standard Specifications and as per the provisions made in the SOR 2022-23. The rate is inclusive of cost of all materials and labour charges and all taxes, duties and levies, etc., complete for finished item of work, but including cost of DI pipes, DI Valves, etc, and excluding GST and Seigniorage charges, including Overheads and Contractors Profit @13.615%. 1). All concrete members shall be designed with M30 grade design mix. 2) Rate is for OHSRs with RAFT FOUNDATION 3) Rate inclusive of three coats of epoxy paint Food Grade of best quality to inner surface of the Reservoir including bottom of roof. 4) Rate inclusive of 2 coats of whether proof emulsion painting for external surfaces, lettering, all required fixtures, pipes, bends, valves etc., for pipe connections including cost of pipes, bends and valves as per departmental designs and drawings. 5) The above rates are applicable for basic wind speed of 180 KMPH . Fixtures include : a) RCC or Aluminium ladder inside 0.60 m wide. b) Spiral staircase on the outside shall be provided upto 200 KL. c) Lightening arrestor, including conductor and earthling etc.,d) RCC ventilators with copper or stainless steel fly proof mesh. e) D.I Manholes frame and cover 0.60x0.60m as per IS specifications (light duty) - 2 Nos. f)Water level indicator of good quality with ebonite/copper float of approved pattern-1 No. g) The railing provided to the gallery and staircase shall be with stainless steel of grade 304 for a height of 1.20m. i) D.I swan neck ventilators shall be provided in top dome and slab. j). Bed Blocks of 0.45m x 0.45m x 0.30m in CC M15 Mix below all the duck foot bends k) The rates are inclusive of DI verticals for all inlet, out let, overflow and scour connections( as per estimate diameters) and D.I valves. All valves near inlet, out let and for scour shall be D.I valves of heavy duty conforming to the specification of SoR item No.30

Construction of pipelines for water supply with 63mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 75mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 75 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of pipelines for water supply with 63mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 75mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Supply and delivery of "Resilient Seated Soft Sealing" Gate Valves (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, Replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The Valves should be Vacuum tight and 100% leak proof with face to face dimensions as BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN-3202F4/BS:5163 Type A Flange drilling as per IS:1538, complete for finished item of work The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of work, construction of valve chamber but excluding GST and Seigniorge charges as specified in Technical specifications including overheads and Contractor's profit @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 75 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Drilling of Bore Well by down the hole hammer drilling to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as mediam hard rock formation to hard rock formation,all consolidated formation etc., and drilling in overburdem to dia not less than 200 mm etc., and remaing the bore well to suit insertion of suitable UPVC outer and inner casing pipes etc., including insertion of casing pipe with slotting (with couplilngs,caps any other relevent materials up to required depth as directed by the department including transportion of drilling rigs and supporitng vehicle and including bore development (flusing of bore well at an average pressure of 150 PSI) conducting yield test , consumables charges , crew charges required in fixation of pipe assembly completely done to the satisfaction of depatment and including all labour charges ,the cost of casing pipe,couplings,cap ,Geological survey charges etc.,but excluding taxes .The entire work should be carried out as per IS 2800 part I&II 1979 and amended from time to time. The work is to be carriedout at site/location selected by the department including cost and conveyance of all materials,labour etc, for finished item of work including Over heads and Contractor profit @13.615% but excluding GST .

Supply and Transportation of 5 Star rated Submersible motor pumpsets,confirming ot IS 8034 and Motor confirming to IS 9283 with water proof winding,pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 240 V +/- 10%,Single phase 50 Hz AC supply,etc., complete for Bore well. Makes: Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/AryenVarsha/ Falcon. The work inclusive of all the essential accessories like suction pipe,Valves, Copper cable earthing, end cap, MS clamp, Panel board with standard make etc., The scope including all labour charges, erection charges, cost of all the materials to the extent of departmental satisfaction for finished item of work including Over heads and Contractor profit @13.615% but excluding GST.

Construction of pipelines for water supply with 63mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 75mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 90mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 110mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 140 mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Supply and delivery of "Resilient Seated Soft Sealing" Gate Valves (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, Replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The Valves should be Vacuum tight and 100% leak proof with face to face dimensions as BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN-3202F4/BS:5163 Type A Flange drilling as per IS:1538, complete for finished item of work The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of work, construction of valve chamber but excluding GST and Seigniorge charges as specified in Technical specifications including overheads and Contractor's profit @ 13.615%.

Supply and delivery of "Resilient Seated Soft Sealing" Gate Valves (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, Replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The Valves should be Vacuum tight and 100% leak proof with face to face dimensions as BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN-3202F4/BS:5163 Type A Flange drilling as per IS:1538, complete for finished item of work The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of work, construction of valve chamber but excluding GST and Seigniorge charges as specified in Technical specifications including overheads and Contractor's profit @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 75 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 90 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 110 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of pipelines for water supply with 63mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 75mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 90mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 110mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 75 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 90 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 110 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Drilling of Bore Well by down the hole hammer drilling to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as mediam hard rock formation to hard rock formation,all consolidated formation etc., and drilling in overburdem to dia not less than 200 mm etc., and remaing the bore well to suit insertion of suitable UPVC outer and inner casing pipes etc., including insertion of casing pipe with slotting (with couplilngs,caps any other relevent materials up to required depth as directed by the department including transportion of drilling rigs and supporitng vehicle and including bore development (flusing of bore well at an average pressure of 150 PSI) conducting yield test , consumables charges , crew charges required in fixation of pipe assembly completely done to the satisfaction of depatment and including all labour charges ,the cost of casing pipe,couplings,cap ,Geological survey charges etc.,but excluding taxes .The entire work should be carried out as per IS 2800 part I&II 1979 and amended from time to time. The work is to be carriedout at site/location selected by the department including cost and conveyance of all materials,labour etc, for finished item of work including Over heads and Contractor profit @13.615% but excluding GST .

Supply and Transportation of 5 Star rated Submersible motor pumpsets,confirming ot IS 8034 and Motor confirming to IS 9283 with water proof winding,pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 240 V +/- 10%,Single phase 50 Hz AC supply,etc., complete for Bore well. Makes: Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/AryenVarsha/ Falcon. The work inclusive of all the essential accessories like suction pipe,Valves, Copper cable earthing, end cap, MS clamp, Panel board with standard make etc., The scope including all labour charges, erection charges, cost of all the materials to the extent of departmental satisfaction for finished item of work including Over heads and Contractor profit @13.615% but excluding GST.

Construction of pipelines for water supply with 63mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 75mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Supply and delivery of "Resilient Seated Soft Sealing" Gate Valves (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, Replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The Valves should be Vacuum tight and 100% leak proof with face to face dimensions as BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN-3202F4/BS:5163 Type A Flange drilling as per IS:1538, complete for finished item of work The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of work, construction of valve chamber but excluding GST and Seigniorge charges as specified in Technical specifications including overheads and Contractor's profit @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 75 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 90 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Drilling of Bore Well by down the hole hammer drilling to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as mediam hard rock formation to hard rock formation,all consolidated formation etc., and drilling in overburdem to dia not less than 200 mm etc., and remaing the bore well to suit insertion of suitable UPVC outer and inner casing pipes etc., including insertion of casing pipe with slotting (with couplilngs,caps any other relevent materials up to required depth as directed by the department including transportion of drilling rigs and supporitng vehicle and including bore development (flusing of bore well at an average pressure of 150 PSI) conducting yield test , consumables charges , crew charges required in fixation of pipe assembly completely done to the satisfaction of depatment and including all labour charges ,the cost of casing pipe,couplings,cap ,Geological survey charges etc.,but excluding taxes .The entire work should be carried out as per IS 2800 part I&II 1979 and amended from time to time. The work is to be carriedout at site/location selected by the department including cost and conveyance of all materials,labour etc, for finished item of work including Over heads and Contractor profit @13.615% but excluding GST .

Supply and Transportation of 5 Star rated Submersible motor pumpsets,confirming ot IS 8034 and Motor confirming to IS 9283 with water proof winding,pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 240 V +/- 10%,Single phase 50 Hz AC supply,etc., complete for Bore well. Makes: Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/AryenVarsha/ Falcon. The work inclusive of all the essential accessories like suction pipe,Valves, Copper cable earthing, end cap, MS clamp, Panel board with standard make etc., The scope including all labour charges, erection charges, cost of all the materials to the extent of departmental satisfaction for finished item of work including Over heads and Contractor profit @13.615% but excluding GST.

Construction of pipelines for water supply with 63mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 75mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Construction of pipelines for water supply with 90mm dia, 6 Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation manually for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B,Volume-I) and as per drawing (as per standard drawings). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding GST and seignourage charges but including Overheads and Contractor's profit @ 13.615%

Cut opening of Cement Concrete road surface with concrete saw cutter and removal with breaker etc., including all charges compete, including overheads and controctor's profit @ 13.615%, GST and seignourage charges

CC 1:2:4 concrete mix including cost and conveyance of all materials and labour charges, complete for restoration of Cement Concrete road cutting, including overheads and contractor's profit @ 13.615 %, but excluding GST and seignourage charges

Supply and delivery of "Resilient Seated Soft Sealing" Gate Valves (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, Replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The Valves should be Vacuum tight and 100% leak proof with face to face dimensions as BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN-3202F4/BS:5163 Type A Flange drilling as per IS:1538, complete for finished item of work The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of work, construction of valve chamber but excluding GST and Seigniorge charges as specified in Technical specifications including overheads and Contractor's profit @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 75 mm dia main with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 63mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and anufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.