SPECIAL REPAIR TO BLDG NO T126 AND T138 COOK HOUSE AND PROVN OF SEPTIC TANK SOAKAGE WELL AND DRAINAGE LINE BEHIND EXISTING BATHROOM NEAR BLDG NO P58 AT SUNDERBANI UNDER GE NORTH AKHNOOR

Amount

Dismantling of frame work timber scantling 40 Sqcm and over in section, in any position.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for.

Demolition of cement concrete (Un reinforced) in ground floors n.exc 15cm thick (above or below grnd level) complete all as specified.

Demolition of stone/brick masonary built in cement/cement lime mortar.

Demolition of stone slab and tile of bed bedded and pointed in any morter or any description or thickness in floor etc.

Walling of squared rubble regular coursed, well bonded, bedded and solidly hearted built in CM 1:4 complete all as specified.

Ditto all as per item No 06 above but except stones.

Dismantling plain or corrugated AC sheeting, any guage, thickness, roof covering.

25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate, as in sub base of floor complete all as specified and as directed by Engineer-in-charge.

Non skid ceramic coloured tiles grade B-IIa 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 sqm, in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match including 15 mm thick screed bed in cement and sand mortar 1:4 complete all as specified.

Ditto all as per Item No 10 but on vertical surface such as skirting dado and riser to step etc.

Non skid coloured ceramic tiles grade B-IIa 7mm to 8mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in light shade floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces incl 15mm thick screed bed/bedding layers in cm 1:4 all as spd & directed.

Glazed ceramic tile 300 x 200 x 7mm thick (coloured) on vertical surfaces such as dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10 mm thick rendering in cement and sand mortar 1:4 complete all as specified.

Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 20mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified.

Machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and including 10 mm thick rendering in cement and sand mortar 1:4. all as specified.

Demolition of reinforced cement concrete in roofs, floors, slabs, beams, staircase,Landings, chajjas & similar suspended work all as specified.

TMT Bars, 10mm dia over cut to length , bent to shape reqd including cranking bending and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips all as specified .

ditto all as per item No 17 but 6 to 8 mm dia.

Reinforced cement concrete type B1, 1:2:4 (using 20 mm graded crushed stone annulled ston aggregate) as in shelves, deck slabs and in similar works all as specified .

Use and waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick surface horizontal or sloping, fair finished surface of concrete, all as specified.

Form work to sides and sofits or floor beam bunching girders brossuuners lintel cantilevers shelves including supports overhangs etc to obtain rough finished surface of concrete.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws incl ridge all as specified.

Ditto all as per item No 22 above here but plain sheets.

Taking down chowkhat or frames of door/ window / ventilators with shutter(Without taking off shutter from the frame) n.exc 1.50 m each.

Taking down chowkhat or frames of door/ window with shutters (Without taking off shutter from the frame) exc 1.50 m and n.exc 4.00 Sqm each.

Taking down cement plaster from brick or stone walls incl racking out joints hacking for key, scrubbing down with water etc.

Rendering 20 mm thick cement plaster with cement mortar (1:4) on fair faces of stone surface or concrete surfaces and finished even and smooth without using extra cement with using water proofing compound.

Rendering 20 mm thick cement plaster with cement mortar(1:6) on other than fair faces of stone surface or concrete surfaces and finished even and smooth without using extra cement.

Rendering 15 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified

Rendering 15 mm thick in cement and sand mortar 1:6 on other than fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified.

Preparation of new/old treated surfaces and apply two coat of cement base paint to walls over a coat of chalk whiting.

Preparation of old treated surfaces and apply one coat of cement base paint to walls.

Preparation of new/old treated surfaces and apply Two coat of oil bound distemper to walls over one coat of chalk whiting.

Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia thresh old bar and filling hollow of frame with plain cement concrete Type C-0, 1:3:6 (using 12.5 mm graded crushed stone aggregate) of following sizes of frame :- (a) 125 mm x 60 mm

(b) 105 mm x 60mm

Factory made Plain framed, second class hard wood panelled shutter (Two panel), 35 mm thick with lock rail and panel of 12 mm thick veneered particle board with commercial veneering on both face. The size of rail and style as per IS-1003 (Part-I), Kiln seasoned and chemically pressure treated.

Glazed and skelton shutters 35 mm thick second class hard wood, opened rebated and prepared to receive wire mesh etc, edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for sucuring witre mesh etc. Size of members of shutters as specified in SSR Part-I, Sec-8, clause 8.24(a).

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top and bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as a gap insert for top rail and bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S frame welded / sealed to the stiles and nails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at side as per specification and drawings.

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specifiecation and drawings.

Aluminium anodised barrel tower bolt 150 mm, extruded section.

Aluminium anodised sliding door bolts with hasp and stapple extruded section or cast aluminium alloy 300 mm long.

100mm butt hinges, medium weight cold rolled mild steel.

Aluminium handle cast type anodised 125 mm long.

Curtain rod, mild steel chromium plated 25mm bore and fixed with brackets all as specified.

Steel windows with side hung shutters incl projecting type hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded.

Steel windows with side hung shutters incl projecting type hinges with steel handle and steel peg stay complete without glazing bars dovetailed or welded.

Steel ventilators with top hung shutters incl e hinges, with steel handle and steel peg stay complete.

Frame work such as grills, frame, gratings etc ends of bars shouldered and/or riveted, welded or forged into spikes, framed guard bars and work conforming to Fe 410-0.

Glazing with sheet, 3mm thick, ordinary quality and glazing with oil putty and glazing pins in squares not exceeding 0.5 Sqm in each pane.

Galvanised steel wire cloth, 0.56mm nominal dia of wire and average with of aperture 1.18mm. And fixed with tinned tack or galvanised wire stapples complete

Preparation of new untreated wood and wood based surfaces of any description, not otherwise described over 10cm width or girth and painting with two coats of synthetic enamel paint over a coat of pink primer

Preparation of old untreated wood and wood based surfaces of any description, not otherwise described over 10cm width or girth and painting with one coat of synthetic enamel paint over existing surface.

Preparation of new steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide premier.

Preparation of old steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and painting with one coat of synthetic enamel paint.

Rolled mild steel section as in main and cross beams, hip and jack,rafters, purlins, where connected to common, rafters and running rails and guiders for sliding doors fixed with angle cleats or other connecting plates conforming to grade Fe 410-W (Gde E-250) quality 'A' all as specified

Plates (plain or chequerred) channels square cut or notched (ordinary and counter sunk) forming holes without any attachment.

Fixing only hand rail half round or other steel section or core for wooden hand rail straight portion, drilled and countersunk for baluster running bars, for door baluster incld embedding in concrete and screwing etc wind ties for roof incld securing bolt post and struts in fencing etc and similar work conforming to Fe-290 Gde E-165

Cutting opening through walls for door, window and other opening etc cutting out defective masonry for underpinning incl providing fixing nad removing , cleaning and removing surplus to store and rubbish off the premises.

Taking up or down 15 mm bore GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

15 mm GI tube medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

Refixing 15mm GI tubing and connection in new or old position(walls, ceiling and floors etc) including all fittings all as specified and directed.

Bib tap cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe 15 mm dia fixed in repairs complete all as specified.

Wash hand basin vitreous china white 550mmx400 mm (flat back or angle back type) including cutting for and pinning in end of the new brackets with 32 mm bore CP waste coupling fixed in repair complete all as specified.

Vitreous china sqatting pan orissa pattern size 580x440mm white with integral footrest including lime concrete bedding fixed as in repair complete all as specified.

PVC valveless syphonic action type flushing cistern, low level white with inlet ball valve flaot and handle including brackets. 10 ltr capacity fixed in repair complete all as specified.

PVC connection 15mm bore size with PTMT nuts of length 450mm.

Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges

32 mm dia PVC waste pipe 90 cm long fexible type for Wash basin

Pillar tap cast copper alloy with capstan head chromium plated fancy type, screwed down high pressure 15mm dia bore fixed in repair complete all as specified.

Angle/stop cock valve of CP any colour high pressure screwed foriron pipe of dia 15 mm.

Steel chromium plated round grating 100mm dia, fixed in position in cement mortar (1:3) complete all as specified.

Dismantling water tanks exc 250 ltr but n.exc 500 ltrs capacity and removing to store complete.

Rotational moulded HDPE water storage tanks (Cylindrical vertical closed top), double wall construction,hoisted and fixed in position or placed in position inside or outside the bldg connecting up pipes and security access covers complete 500 ltrs complete all as specified.

Ball valve high pressure of PTMT withepoxy coated Aluminum rod & high density plastic ball screwed for iron pipe or brass ferrule and fixed in repair 25mm bore complete all as specified.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness including cover fillets.

GI frame work 605 x 605 mm for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soft it at approx x 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 centre to centre including 4 mm thick designer ceiling board in grid.

Granite (of any type) as on kitchen plateform tiles 18-20 mm thick machine cut, bedded andjointed with grey cement slurryand pointed with white cementwith admixture of pigment tomatch the shade of granite stoneincluding grinding and polishing complete all as specified.

Mild steel springs for doors, 150 mm, ordinary rat tail rod pattern springs including roller and roller plate complete.

Providing cement concrete type C-1, 1:3:6 ( using 20mm graded stone aggregate), 50 mm thick , 75cm wide as in plinth protection laid in bays not exceeding 2 Sqm each and finishing even and fair on top without using extra cement with 6mm wide joints throughout the thickness of plinth protection in concrete bays and in between the walling and plinth protection, filling the joints with mastic filling comprising of one part of heated bitumen 85/25 or 95/10 grade and 3 parts of sand ( all by weight).

Mild steel flat iron for wind ties for roof including securing bolts necessary drilling bolting or riveting etc and similar work conforming to Fe 210 Gde E-165

Supply only integral water proofing compound.

Septic tank for 25 user, excavation in ordinary soil, foundation in PCC (1:2:4), brick work in cement mortar (1:4), RCC slab covering in M-25 including RCC precast manhole cover having 6mm plate embedded all around/fiber reinforced cover with angle iron frame vent shaft and sludge chambers complete as per drawing No CE/TD-1202/2003 Sheet 1/2 & 2/2 including upto date amendments

Soakage wells, excavation in ordinary soil, foundation in PCC (1:3:6) wells of Honey Combed and solid in M-25 concrete, including intercepting chamber, sreen chamber, brick work in cement mortar (1:4), RCC cover slab in M-25 /RR masonry / filing with brick bats complete of size 1.80 mtr internal dia and 3.00 mtr deep as per drawing No CE/TD-1202/2003 Sheet 1/2 & 2/2 including upto date amendments

PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in foundations filling and mass concrete complete all as specified.

PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregates as in foundations filling and mass concrete complete all as specified.

Providing cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregates as in beds of SGSW pipe 150mm bore, laid to required slope including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed by Engineer-in-Charge.

150mm bore (internal diameter) salt glazed stone ware drain pipes grade ‘A’ laid in trenches on concrete bed to slopes, jointing and testing including fittings complete all as specified and as directed by Engineer-in-Charge.

Brick work with sub class "B" bricks straight or curved on plan exceeding 6 metre mean radius in cement mortar 1:4 , all as specified .

Brick work with sub class "B" bricks straight or curved on plan exceeding 6 metre mean radius in cement mortar 1:6 , all as specified .

Ditto al as per item No 90 but except brick

Plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregates as in cills,lintels upto 1.50 metre clear span , copings etc. and in similar works including weathering,slightly rounded or chamfered angles and throating and necessary form works, all as specified in clause 4.11.16.2(e) of MES Schedule Part-I.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement all as specified

Providing precast cement concrete (1:2:4 Type B-1 using 20mm graded aggregate) as in cover slabs for drains etc and set in cement mortar (1:6) complete all as specified.

Providing cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in surface channel and drain including necessary form work complete all as specified.

Extra for forming fair finished drain or channel not exc 50 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc. all as specified.

Cement concrete work in pavement standing of flexural strength 40 Kg/Sqcm in field using 400Kg of cement per cum thickness of concrete 25cm or less

Finishing surface of concrete by brooming

Forming 12mm thick expansion joints filled with pre formed bituminous filler and top 30mm primed and sealed with sealing compound grade "A" complete all as specified.

Taking down carefully, copper / aluminium conductor unserviceable / perished point wiring (any type) for light/ fan/ light socket or power socket etc complete with fittings such as switches, sockets, ceiling roses, pendant holders, bracket holder, light fittings, regulators etc, including making good to disturbed surfaces of wall/floor etc, complete, all as specified & directed.

Taking down main switches, distribution boards etc of any type and capacity along with the existing boards, and removing the same from site and making good the disturbed surfaces/portion of walls etc. all as directed.

Point wiring with multi stranded FRLS PVC insulated unsheathed copper conductor cable single core of 1.5 Sqmm drawn into and including PVC casing and caping 'ISI marked' of 20/30mm size as required, terminated in MS sunken box suitable for housing of switches, socket, regulator etc, covered with 3mm thick bakelite 'hylam' laminated sheet cover complete with all accessories, fixing arrangements on wall /roof/floor by means of drilling by heavy duty hand drill and fixing with PVC rawl plug and screws including single core FRLS PVC insulated unsheathed multi stranded copper conductor cable of 1.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one light/fan point controlled by one way switch, complete all as specified & directed.

All as per Srl item No. 102 above but for one 3/5 pin 5 Amps socket outlet on same board .

All as per Srl item No. 102 here-in-before but for one 3/5 pin 5 Amps socket outlet on independent board.

Point wiring with multi stranded FRLS PVC insulated unsheathed copper conductor cable single core of 2.5 Sqmm drawn into and including PVC casing and caping 'ISI marked' of 20/30mm size as required, terminated in MS sunken box suitable for housing of switches, socket, regulator etc, covered with 3mm thick bakelite 'hylam' laminated sheet cover complete with all accessories, fixing arrangements on wall /roof/floor by means of drilling by heavy duty hand drill and fixing with PVC rawl plug and screws including single core FRLS PVC insulated unsheathed multi stranded copper conductor cable of 2.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one 3/5 pin socket outlet 15 Amps independent, complete all as specified & directed. Notes for Srl Item No. 102 to 105 (i) Unit rate includes for cutting chases whereever required and sinking for boxes, making good to walls / floors etc., complete, including white wash / colour wash as directed. (ii) Uniform coding of wiring i.e red / yellow / blue for phase black for neutral and green for earth is to be maintained.

Switch socket combination, two in one, 6 pin type, 5 & 15 Amp, flush type universal, complete all as specified & directed.

Switch socket combination, two in one, 5 pin type, 5 Amp, flush type universal, complete all as specified & directed.

Socket outlet two in one, 5 pin type, 5 Amp, flush type, complete all as specified & directed.

Ceiling rose surface type, bakelite 65mmx50mm, 3 terminals, complete all as specified & directed.

Switch piano flush type 5 Amps 240 Volt, single pole one way, complete all as specified & directed.

Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified & directed.

LED lamp in white colour of 7 watt, base Cap B-22, complete all as specified & directed. Make : Philips/ Crompton/ Bajaj/ Wipro/ Syska Led/ GE Lighting/ Surya/ Havells

Sheet metal enclosure, factory made for DBs, protection class IP-36, phosphatised powder coated, double door when MCB's to be used, single pole & neutral, 240 volts with 200 amps rated copper bus bar & neutral link earthing stud, 12 way, complete all as specified & directed.

Sheet metal enclosure, factory made for DBs, protection class IP-36, phosphatised powder coated, double door when MCB's to be used, single pole & neutral, 240 volts with 200 amps rated copper bus bar & neutral link earthing stud, 8 way, complete all as specified & directed.

MCB, single pole & neutral, 32 to 63 Amp, AC, 10 KA repturing capacity, 240 Volt, 'C' series, complete all as specified & directed.

MCB, single pole, 6 to 32 Amp, AC, 10 KA repturing capacity, 240 Volt, 'C' series, complete all as specified & directed.

Fan regulator, deluxe socket type (electronic step type) for 1200/1400 sweep AC ceiling fan, complete all as specified and directed.

Earthing of galvanized steel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr depth below normal ground level) with top edge of earth not less than 1.5 mtr below normal ground level, surrounded on all sides by 150mm thick charcoal & common salt starting from ground below earth plate upto 150mm above GI plate in alternate layers connected to and including earth lead wire 4.0mm (8SWG) by means of steel bolts, nuts, check nuts and washers, test point made of GI strip 40x8mm, 10cm long PCC 1:2:4, type B-1 in pit with precast RCC 1:2:4 type B-1 in cover reinforced with XPM not less than 4 Kg per Sqm with 15mm bore GI light grade protection pipe, 20mm bore GI medium grade watering pipe with funnel including charcoal, dust, salt, all as shown in electrical plate No 3 of SSR Part-I (2009) complete with necessary earth work in any type of soil, removal to a distance not exceeding 50 mtr, including testing on completion, complete all as specified & directed. Note : (a) The cost of earth work, PCC pit of size shown in electrical plate No.3, funnel, watering pipe, wire mesh, charcoal, dust, common salt, 20mm bore medium grade watering pipe & 15mm bore light grade GI pipe as protection to earth lead wire etc shall be deemed included in the unit rate for earthing. (b) After completion, during testing, if the earth resistance equal or less 2 ohms is not obtained, earthing will be regenerated at no extra cost till the desired earth resistance is obtained.

Energy saving 10W LED bulk head luminaires, IP-65, oval shape, surface mounted with all other accessories prewired and making connections with copper flexible twisted twin cord of appropriate gauge and length,230v, 50Hz including taking down old unserviceable fitting including taking down old unserviceable fittings, complete all as specified & directed. Make. Havells, Cat Part No.RUGBYNEONFT10WLED760SSYMBOPC or equivalent in Philips/ Crompton/ Bajaj/ Wipro/ Syska Led/ GE Lighting/ Surya

Surface & wall mounted, LED tube light fitting, 20W, glare free, smooth light distribution, 230v, box type, epoxy powder coated CRCA sheet housing with reflector cover channel, aesthetic looking end cap and HPF LED driver with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size, complete all as specified & directed. Make. Havells, Cat Part No. ENDURALINEARNEOBS20WLED865SPCWH or equivalent in Philips/ Crompton/ Bajaj/ Wipro/ Syska Led/ GE Lighting/ Surya

Taking down existing ceiling fan of any size and refixing the same after repair of building including provision of three core flexiable copper cord of size 23/0.0076 of required length from ceiling rose or connector to ceiling fan, complete all as specified & directed.

XLPE insulated, armoured heavy duty electric cable (heavy duty) with aluminium conductor, 1100 volts grade, cross-sectional area 10 Sqmm 2 core connected with suitable cable gland and aluminium lugs, laid in trenches or passing through pipes including testing, complete all as specified and directed. (Earth work, brick protection and sand cushioning shall be measured and paid for separately)

Excavation in trenches n.exc 1.5m in width and n.exc 1.5m in depth and getting out in any type of soil for laying pipe line complete all as specified.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete, all as specified.

Removing excavated/surplus material not exceeding . 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified.

Galvanised iron tube 32mm bore light grade (ISI marked) for cable protection to poles/under floor/under roads/alongwith walls complete including sealing of pipe ends with approved sealing compound, complete all as specified and directed.

Sand cushioning to under ground cable, laid in trenches 8cm thick below the cable and 15cm thick above the cable after laying and stretching the cable complete punned to 18cm, complete all as specified and directed. Note:- Punned thickness of sand will be measured and paid.

Brick well burnt locally available sub class 'B' laid over sand cushioning for mechanical cable protection in trenches with width of brick perpendicular to the length of cable, complete all as specified & directed.

Taking out old unserviceable service connection or cable

Rectangular heavy duty PVC block of size 40 x 30 x 5 cm depth complete all as specified.

ASIA ENTERPRISES

M/S K K ENTERPRISES