ADDITION / ALTERATION TO SENTRY POST, PROVN OF WAREHOUSE FACILITY WITHIN PC EQUIPMENT STORE AND CERTAIN SANCTIONED WORKS AT CG JETTY PORBANDAR UNDER GE (I) CG PORBANDAR

Amount

SCHEDULE 'A'

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cessipts, manholes, pier holes, etc. n exc 10 Sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick using excavated material all as specified.

Removing excavated material to a distance n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point all as specified and as directed by engineer-in-charge.

Forming embankments including raising (or lowering) earth, spreading in layers n exc. 30cm thick; watering, ramming/rolling and finishing to required size, shape, etc., n exc. 1.5m high from base

M&L Hardcore of guage n.exc. 63mm, deposited spread & levelled in layers n.exc.15CM thick, watered & rolled/ rammed to a true surface using broken stone or boulders all as specified and as directed by engineer-in-charge.

Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured)

Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface

Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area

M&L Plain cement concrete, type D2, (1:4:8, using 40mm graded stone aggregates) as in foundation, filling and mass concrete etc all as specified and as as directed by engineer-in-charge. Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in foundation including raft footing foundation beam plinth beam bases for columns etc basement slab under reamed piles and mass concrete Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in Columns,pillars,piers, posts and struts Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in chajjas, floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like. Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in beams,cantilevers, bressumers and lintels over 1.5 mtr span complete all as specified and directed by Engr-in-charge. Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in slabs supported onwalls, beams and colums in floors, roofs, landings, balconies, canopies ,deck slabs and in shelves and the like complete all as specified and directed by Engr-in-charge Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

Supply only water proofing compound with ISI Marking.

M& L Marble Baroda green 18 to 20 mm thick (table rubbed and polishing) as in skirting/dado/ window cills/ jambs, vertical surface over cement rendering and jointed with grey cement,over and including screed bed of 15mm thick in CM 1:4, and making nosing at right angle corner as directed by Engr-in-charge complete.

Formwork to sides of concrete foundations, footings,bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work;vertical or to batter,curved, as in rough finished surfaces of concrete complete all as specified and as directed by engineer-in-charge.

Formwork to sides of pillars, posts, struts, piers, columns (square, rectangular or polygonal) as in fair finished surfaces of concrete complete all as specified and as directed by engineer-in-charge.

Formwork to sides and soffits of floor or roof beams,beam haunchings, girders, bressumers, lintels, cantilevers, shelves including supports, overhangs, chajjas etc also splays between floor and beam and the like for fair finished surfaces of concrete etc complete all as specified and directed by Engr-in-charge.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, roof beam landings and similar work; not exceeding 200m thick for fair finished surface (Horizontal or sloping) etc complete all as specified and directed by Engr-in-charge.

M&L 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and as directed by Engr-in-Charge.

S & F 35mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc but divided into squares, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads etc complete all as specified and directed by Engr-in-Charge.

S & F 35mm thick 2nd class hard wood plain framed panelled shutter (any number of panels) with panels of timber flat on both sides, feather edged or of veneered particle board medium density, wood particle board with commercial face veneer etc complete all as specified and directed by Engr-in-Charge.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC Sheet rainforced with MS square tube complete all as specified and as directed by Engr-in-Charge

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and as directed by Engr-in-Charge

S&F Butt hinges, 100 mm medium weight, cold rolled mild steel complete all as specified and as directed by Engr-in-Charge.

S&F Aluminium, anodised, barrel tower bolts 200 mm long of extruded section and fixed complete all as specified and as directed by Engr-in-Charge.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed by Engr-in-Charge.

S&F aluminum handles cast type anodized 125 mm size complete all as specified and as directed by Engr-in-Charge.

S&F 140mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor

S&F Brass chromium plated finials for curtain rod complete all as specified and as directed by engineer-in-charge.

S&F 20mm dia Powder coated Aluminium anodised alloy curtain rod, of approved make with fixing brackets, all as specified and as directed by Engineer-in-charge. Note: colour of curtain rod shall be approved by Engineer-in-Charge.

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by Engr-in-Charge.

M&L Porbandar stone masonary, block in course, well bonded and bedded, built in CM 1:6 all as specified and as directed by engineer-in-charge.

M&L Mild steel CRS TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips. etc complete all as specified and directed by Engr-in-charge.

M&L Mild steel CRS TMT bars 6 to 8 mm dia Round Bars cut to length bent to shape required including cranking bending spirally for hooping for colums hooking ends and bending with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed by Engr-in-charge.

All as per above item No.36.00 but 5mm dia and over upto 10mm dia as in stirrups, spacers and binders etc complete all as specified and directed by Engr-in-charge.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered/welded or riveted, or forged into spikes; framed guard bars; Square Bar, Flat Iron, barred iron doors; ladders; framed balusters; walk ways; railings; cutting, welding , framework of water tanks and similar work con-forming to Fe.290.Gde-E-165 in Existing grill work complete all as specified and as directed by the Engineer-in-Charge.

S&F powder coated Anodised aluminium frame (minimum thickness of powder coating 50 micron) for doors, shutters, sliding windows and windows ventilators with or without rebates including joining cleats for fixing etc. complete all as specified and as directed by Engr-in-Charge.

S&F 5mm thick Sheet glass,ordinary qualityand glazing with oil putty in square n exc 0.5sq. m in each pane all as specified and as directed by engineer-in-charge.

S&F Aluminium grill with suitable aluminium anodised frame F/H section manufactured by M/s DECO GRILL as per design No DG-104, 6.5 mm thick. complete all as specified and as directed by Engr-in-Charge.

S&F Neoprene rubber beading of U or C section suitable for 5mm thick glass fixed along with edges of aluminium glass panes of joinery, all as directed by Engineer-in-charge.

S&F UPVC, double flat / groove type, roller for sliding windows all as directed by Engineer-in-charge. Note: Rollers shall conform to the samples kept with the Engineer-in-Charge.

S&F 100mm long powder coated Aluminium starlock for sliding window shutters conforming to the samples held in the office of Engineer-in-charge.

M & L 100mm thick PCC Cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in floor as a sub base for kota stone

M & L 25mm thick PCC Cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in floor as a sub base for kota stone

M&L Joint free coloured ceramic tiles 8 to 9 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry over screed bed 15 mm thick 1:6 and pointed in white or coloured cement to match including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engr-in-Charge.

All as per item ser no 47.00 here-in-before but in skirting/dado or verticle surfaces with back coat bedding layer of 10 mm thick 1:4 and pointed in white or coloured cement to match complete all as specified and as directed by Engr-in-Charge.

M&L Glazed coloured ceramic tiles in verticle surfaces 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match with backcoat bedding layer 10mm thick in cement mortar, 1:4 and pointed in white or coloured cement to match complete all as specified and as directed by Engr-in-Charge.

M&L for 50mm thick Cement concrete type C-1, 1:3:6 (20mm graded aggregate) as in flooring finishing even and smooth without using extra cement.

M&L for 75mm thick Cement concrete type C-1, 1:3:6 (20mm graded aggregate) as in flooring finishing even and smooth without using extra cement.

M&L for 100mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in flooring finishing even and smooth without using extra cement.

M&L Rendering on wall 15mm thick in CM 1:6 on brick work or concrete surfaces finished fair and even without using extra cement.

M&L Rendering on wall 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished fair and even without using extra cement.

M&L Rendering on ceiling 5 mm thick in CM 1:3 on brick work or concrete surfaces finished fair and even without using extra cement.

M&L Two coats of OBD on new plastered surfaces of wall over a coat of chalk white primer including preparation of newly plastered surfaces complete all as specified and as directed by Engr-in-Charge.

M&L Two coats of OBD on new plastered surfaces of ceiling over a coat of chalk white primer including preparation of newly plastered surfaces complete all as specified and as directed by Engr-in-Charge.

M&L preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of epoxy paint over a coat of red oxide primer complete all as specified and as directed.

M & L for preparing new wooden surfaces of any description, not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer of approved shade complete all as specified and as directed by Engr-in-Charge.

M & L Preparation of new plastered/concrete surfaces of walls applying two coats of exterior acrylic emulsion (weather proof treatment) over one coat of primer, complete all as specified and as directed by the Engineer-in-Charge. ( The tint and shade be as approved by the GE)

M&L 20mm thick cement plaster in cement mortar 1:4 mixed with water proofing compound as in roof treatment when conc is green complete all as specified and directed.

M&L APP based membrane course roof treatment in layers with following provisions:- (i) Applying one coat of bitumen's primer polymerized primer oil based coat, evenly @ 0.3KG/Sqm as priming coat to the prepared surfaces, till the surfaces is properly impregnated and the solvent oil in the base primer shall be allowed to evaporated completely. (ii) Applying APP based pre-fabricated with non woven polyester reinforced membrane stabilized with fibre glass strands and top with grey mineral slates 3mm thick and weight not less than 3.50 Kg/Sqm by torch application method. (iii) Applying a coat of solar reflective bituminous aluminium paint @ 0.10Kg/Sqm over mineral surface.

Forming Contraction (Dummy) joints 50 mm deep x 10mm wide, filled with grade 'A" sealing compound

Taking up or down steel tubing and connections, including cleaning for refixing or removal to store 15 mm dia complete all as specified and as directed by Engr-in-Charge

Taking up or down steel tubing and connections, including cleaning for refixing or removal to store 20 mm dia complete all as specified and as directed by Engr-in-Charge

S&L 25mm OD, CPVC pipes, of SDR -11 & plain CPVC SDR fittings for Hot/cold water for sizes mentioned below including all fittings and solvents and special fittings like brass elbow, brass tee, male threaded brass adaptor, female threaded brass adaptor etc, Unions, Flange and tank adapter all as per manufacturers recommendations and as specified.

S&L 20mm OD, CPVC pipes, of SDR -11 & plain CPVC SDR fittings for Hot/cold water for sizes mentioned below including all fittings and solvents and special fittings like brass elbow, brass tee, male threaded brass adaptor, female threaded brass adaptor etc, Unions, Flange and tank adapter all as per manufacturers recommendations and as specified.

S&F Vitreous China wash downwater closet pan (pedestal pattern), white (including fixing bolts & flush pipe, plastic water closet seat,black, closed pattern with bottom, and cover and mild steel chromium plated or aluminised hinging device etc.) complete all as specified and directed by Engineer-in-Charge

S&F Vitreous china wash basin, white, flat back, size 550 x 400 mm including waste, waste pipe, brackets including cutting for and pinning in ends of brackets or erecting stand in repairs complete all as directed.

S&F Tubular towel Rail CP Brass, chromium plated D type, 600 mm long between flanges all as specified. Make : Prayag (Cat Pat No-BA-40 or or equivalent as approved by Engr-in-Charge

S&F PVC connections 15mm size with PTMT nuts of length 450mm Make : Prayag and equivalent as approved by Engr-in-Charge

M&L 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F 50mm bore High density polyethylene (LDPE) pipes of pressure rating 6kgf/sq.cm laid in trenches or in any position complete all as specified

S&F 1000 litre capacity rotational moulded polythylene water storage tanks (cylindrical, vertical with closed top ) hoisted and fixed in positionall specified in SSR Part-I. complete all as specified and as directed by Engr-in-Charge

S&F Gun-metal, globe or gate valves 25 mm bore, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by Engr-in-Charge

S&F 20mm dia ball valves high pressure of PTMT epoxy coated aluminium rod & high density plastic ball screwed for iron pipes and fixed complete all as specified and as directed by Engr-in-Charge

S&F 15mm pillar taps, cast copper alloy with captain heads chromium plated screw down high pressure with long screwed shanks and fly nuts screwed for iron pipe and fixed Make : Gem/Soma/Parko/Seiko)

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls of bore 110mm (rates includes for making good disturbed surfaces). complete all as specified and as directed by Engr-in-Charge.

S&F -ditto- all as per item No 80 above, but 75mm dia.

S&F PVC (SWR) bends any radius of 75mm bore. complete all as specified and as directed by Engr-in-Charge.

-ditto- all as per item No 82 above, but 110mm bore.

S&F in repair 110 mm dia PVC (SWR) branch piece, single (single Y) equal or unequal

S&F in repair 110 mm diaPVC (SWR) branch piece, double (double Y), equal or unequal

S&F PVC (SWR) branch piece, single(Y) equal or unequal of 75mm bore.complete all as specified and as directed by Engr-in-Charge.

S&F PVC (SWR) junction single (single T) equal or unequal of 75mm bore complete all as specified and as directed by Engr-in-Charge.

S&F PVC(SWR) vent cowl as specified of dia 75mm bore complete all as specified and as directed by Engr-in-Charge.

S&F Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device.

S&F vitreous China Urinal, Half stall type, white (excluding flushing cistern and flush pipe and waste pipe) complete all as specified and as directed.

S & F 15 mm bore Stop Valve (Concealed Type) Cast Copper Alloy fancy type, Chromium plated with long shank and cup, high pressure, with crutch, screwed both ends for iron pipe or for unions and fixed. Make : Prayag (Cat Pat No-8518) or equivalent as approved by Engr-in-Charge

S&F 15mm dia Bib taps, with flange chromium plated cast copper alloy with crutch or butterfly handle complete all as specified and directed. Make : Prayag (Cat Pat No-8306) or equivalent as approved by Engr-in-Charge

S&F 10 lit.capacity PVC valveless, syphonic action type, flushing cistern,low level, white, with inlet,ball valve, float and handle including brackets complete all as specified. Make : Prayag (Cat Pat No-501) or equivalent as approved by Engr-in-Charge

S&F 15mm Angle Cock, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Make : Prayag (Cat Pat No-8510) or equivalent as approved by Engr-in-Charge

S&F Glass Shelf 500 x 60mm (with ABS Brackets) 450 x 125 x 6mm complete all as specified & directed. Make : Prayag (Cat Pat No- BEA-47) and equivalent as approved by Engr-in-Charge

S&F Corner Glass Shelf 300mm (with ABS Brackets) 300 x 600mm complete all as specified & directed. Make : Prayag (Cat Pat No- BEA-46) and equivalent as approved by Engr-in-Charge

S&F Soap Dish CP Brass complete all as specified & directed. Make : Prayag (Cat Pat No-BA-45) or equivalent as approved by Engr-in-Charge

S&F 7" over head shower with 225mm with flange complete all as Specified. Make : Prayag (Cat Pat No BS-78) or equivalent model as approved by Engr-in-Charge

S&F Health Faucet square with 1 mtr tube and hook complete all as specified and as directed by Engr-in-Charge, fixed in repair. Make : Prayag (Cat Pat No-BEA-85) as approved by Engr-in-Charge

S&F Toilet Paper Holder, complete all as specified and as directed by Engr-in-Charge, fixed in repair. Make : Prayag (Cat Pat No BA-18) or equivalent from makes given in list of makes.

S&F stainless steel grating cover fixed in repairs to suit the 100mm dia nahani trap fixed with cement.

S&F 32mm dia PVC (flexible) waste pipe, 800mm long for WHB/Kitchen sink/Urninal complete.

S&F 40mm dia PVC (flexible) waste pipe, 800mm long for WHB/Kitchen sink/Urninal complete.

S&F 32mm dia CP waste fittings, brass chromium plated for glazed ware sinks, basins, etc, with long screwed shanks & fly nuts, flange end based in red lead cement complete all as specified & directed.

S&F 40mm dia CP waste fittings, brass chromium plated for glazed ware sinks, basins, etc, with long screwed shanks and fly nuts, flange end based in red lead cement complete all as specified & directed.

S&F Cabinet Mirror 400 x 500 mm, Make : Prayag (Cat Pat No 554) or equivalent as approved by GE. complete all as specified and as directed by Engr-in-Charge

M & L for Demolition of reinforcement cement concrete of any description and in any position not otherwise specifically provided, including errection of double steel scaffolding, covering with green cloth and all the safety measures/precautions and complete all as specified and as directed by Engineer-in -Charge. (i) Note: Contractor should take all precautions and ensure no damage to building structure & using steel scaffolding.

Demolition for Brickwork or stone/boulder masonry, build in cement or lime mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and as directed.

M&L for 18 to 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over screed bed or bedding layer of 15 mm thick 1:6 etc. complete all as specified and as directed by Engr-in-Charge

Taking down carefully aluminium/copper point wiring (light,fan,socket or power) concealed and casing caping complete including fittings and fixtures such as switches,ceiling roses,pendants,regulators,sockets light fittings and making good the disturbed surfaces of walls/ceiling/floor etc.

Disconnecting of unserviceable sub main wiring of any size and accessories & removing from site and making good the disturbed surfaces.

Disconnecting electric connections and taking down old unserviceable MCB SPN/SP/TP and DB's of any capacity.

M & L Light/Fan point wiring complete with 1.5 Sqmm single core PVC insulated but unsheathed multi stranded copper conductor FRLS cable 650/1100 Volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit (minimum 20 mm dia (external) but shall be increased as per actual site requirement in accordance with clause 19 125 of SSR Part I) ISI marked with wall thickness not less than 1.8 mm including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling etc including 1.5 Sq mm PVC insulated but unsheathed multi stranded copper conductor FRLS cable as earth continuity wire including sunken type pressed steel terminal boxes of suitable size with 3 mm thick bakelite sheet white/coloured top cover complete all as specified and directed.

Ditto all as per item no. 1 above, but for 3 pin 5 amps switch socket outlet on Same board complete.

Ditto all as per item no. 1 above, but for 3 pin 5 amps switch socket outlet on Independent board complete.

Ditto all as per item no.1 above, but for 3 pin 15 amps switch socket outlet with 4 sqmm multi stranderd copper conductor cable on independent board complete.

Supply & fix ceiling rose, surface bakelite, three terminals (ISI Marked) complete all as specified and as directed.

S & F switch piano flush button single pole one way 5 amps complete.

S & F switch socket combination multipurpose 2 in 1, 5amps flush type complete all as specified and directed by EIC.

S & F switch socket combination multipurpose 2 in 1, 3 Pin 5 and 15 Amps flush type universal complete.

S & F in repairs Ceiling fan regulator electronic stepped type, AC, 230 Volts, flush type

Taking Down Ceiling fans 1200/1400 mm sweep and transporting to store for safe custody for reuse or for depositing at the MES Yard.

Fixing only ceiling fan 1200/1400 mm sweep as obtained from taking down vide Ser No 122 herein before including painting of celing fan

S & F wall mounted LED Tube light fitting 1x20W LED Tube T8, 4 feet including making connections with 2 core flexible copper wire 0.50 Sq mm from ceiling rose after fixing fitting in position at site on 02 Nos new round/sqare blocks complete all as specified and directed. Make Wipro - CAT PT No- WIO831208G1or equivalent to Bajaj/Havells

M&L for sub main wiring with two single core 4 Sqmm PVC (FRLS) insulated multistranded flexible copper conductor cable 660/1100 volts grade down in through including Concealed PVC Conduit with all accessories, PVC insulated 2.5 Sqm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed. Note : 1. Two runs of cable, one run of earth wire, one run of PVC conduit will be measured and paid one unit.

S & F MCB DB 8 way SPN, double door, vertical type, IP - 53 with 200 Amps rated bus bar, Concealed and connecting up complete all as specified.

Supply and fixing of MCB SP, 240 volt, 6 to 32 Amps complete all as specified.

Supply and fixing of MCB SPN, 240 volt, 40 Amps complete all as specified.