CERTAIN REPAIR WORKS AND MAINT OF RWA OF Y N LINE, A E LINE AND J S LINE UNDER ZONE B OF GE (A) AHMEDABAD

Amount

Demolition of Brick work or stone/boulder masonry, build in cement mortar or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 complete all as specified and directed.

Taking down cement or lime plaster of any description from stone or brick walls etc including raking out joints, hacking for key scrubbing down with water and disposing off the rubbish complete all as specified and directed.

M&L for 15mm thick rendering on fair faces of brick/ concrete surfaces in CM (1:4) finished even and fair without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick on any faces of brick work in CM1:6, finished even and fair complete all as specified and directed.

M & L for 5mm thick rendering on cement concrete as in ceiling with cement mortaar 1:3 complete all as specified and directed.

M&L for preparation of new surfaces of ceiling plastered/AC sheet and applying three coat of white wash complete all as specified

M&L for preparation of new plastered surfaces on walls and applying two coats of oil bound distemper and a coat of primer all as specifed.

M&L for prepartion of new plastered surfaces on walls and applying two coats cement based paint on walls all as specified and directed by the Engr-in-Charge

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) and disposing off the rubbish materials where complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-1 using 20mm graded stone aggregate 75mm thick as in plinth protection/path finishing the surface even and smooth w/o using extra cement including bitumen joints complete all as specified and directed.

Taking down chowkats or frame with shutters ( without taking off shutters from the frame) n.exc 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frame) exc 1.5 sqm and n exc 4.0 sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but n. exc 2 Sqm each complete all as specified and directed.

S&F 2nd hard wood 35mm thick glazed, and skeleton shutters open rebated & prepared to receive, glass, gauge etc. divided into squares with plain chamfered or rounded mitred and rebated any numbers and size of members of shutters as specifed in SSR Part I, Section 8, clause 8.24(a); supllied and fitted to chowkahts complete all as specified and directed.

S&F 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F mild steel angle iron work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe290 (Gde-E-165)

S&F Mild Steel butt hinges medium weight 100mm long complete all as specified and directed.

M&L for 150mm long extructed aluminium handle fabricated type complete all as specified and directed.

S&F Aluminium anodised barrel tower bolt of extruded section 150 mm size complete all as specified and directed.

S&F aluminium alloy anodised sliding door bolt with hasp and stapple ( bolt type) and fixing clips of sheet cast or extruded section with fixing bolts and sliding bolt of extruded section 300mm length & dia not less than 12mm with & including 6 Nos of bolts complete all as specified and directed.

S&F factory made solid PVC door, cup board shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded both side plain PVC 'C' channel having a plain PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & b PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail, lock rail & bottom rail panelling of both side plain PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading & jointed together with solvent cement, supply & fixing in the frame at site as per SSR specification & diagram/product drawing shown on ser page No 156 of SSR Part II complete all as specified and directed & directed

S&F solid PVC door, cup board frame size 50mmx47mm made out of 5mm plain PVC sheet reinforced with MS square tube all as per specification and as per drawing shown on ser page No 150 of SSR Part II (for item 884) complete all as specified and directed and directed

S&F Stainless steel wire cloth 0.36mm normal dia of wire and average width of aparture 1.40mm and fixed with tinned tacks or Stainless steel wire stapples complete all as specified and directed.

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and averae width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S & F in repairs Sheet glass ordinary quality and glazing with oil putty in square n exe 0.5 sq m in each pane (Thickness in 3.00mm) complete all as specified and directed.

S&F in repair 3 mm thick frosted glass panes and glazing with oil putty & pins/spring pins complete in squares n.exc 0.50 sqm each panes complete all as specified and directed.

S &F powder coated aluminum ventilator having frame of section 57x52 series-B 20535 and shutters, without sash bars, aluminum sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing anodized aluminum snap, beading screws, anodized aluminum fittings such as peg stays 150mm long (1 No). complete all as specified compete all as specified and as directed.

S& F aluminum power coated framed widows, any fixed/side hung sliding three track using powder coated aluminum section or approved make, with or without sash bars, suitable for 4.00 mm thick glazing and stainless steel alloy wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm wire gauze, including necessary rubber packing, joining cleats, glazing clips, aluminums snap beading, handles, locking arrangement, frame of window should be of 1.5mm thick section & shutter sec like handle/interlocking/top/bottom should be of 1.2mm thick etc. complete all as specified and as directed Note. Rates include all glazing/aluminums wire cloth, rubber packing, joining, cleats glazing clips aluminum snap beading, locking arrangements, handle etc complete all as specified and directed.

S&F Aluminum powder coated floor frame of size 100 x 44x 1.98mm thick with one or more repartees and shutters pull and push type or side huge type (with or without aluminium sash bars) comprising of top & lock rails of section 115 x 44 x 1.98mm thick, bottom rail of section 150 x 44x 1.98mm thick stiles of section 85 x 44 mm x 1.98mm thick including necessary jointing cleat glazing clip, rubber packing anodized aluminium beading, screws anodized aluminium fitting such as floor spring or hangers 100mm size with hydraulic door closed, handles ‘D’ types 125mm, floor door stoppers, tower bolt 200 mm, sliding door bolt 300 mm or mortice lock, hydraulic door closer with 5mm thick tinted glass/ preleminated particle board (Novapan) Panel and making good of wall surface to match excising surface complete all as specified.

S&F cast Iron Body Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed.

S&F Aluminium Mortice lock 4 levers, vertical type, size 100 mm complete all as specified and directed.

S & F in Sheet glass ordinary quality and glazing with oil putty in square exe 0.5 sq m in each pane (Thickness in 4 mm) complete all as specified and directed.

S & F in Sheet glass ordinary quality and glazing with oil putty in square exe 0.5 sq m in each pane (Thickness in 5.5 mm) complete all as specified and directed.

Preparation of new or previously untreated wooden surfaces of any description, not otherwise, described, over 10cm width or girth and applying two coats of synthetic enamal paint over a coat of pink primer complete all as specified.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M & L Non Skid ceramic coloured tiles 7mm to 8mm thick, (square or rectangular) area of each tile exc 0.06 Sqm but n. exc 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over incl screed bed or beeding layers of mortar 15mm thick in CM 1:6 in floors, complete all as specified and directed.

M & L Non Skid ceramic coloured tiles 8mm to 9mm thick, (square or rectangular) area of each tile exc 0.18 Sqm but n. exc 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over incl screed bed or beeding layers of mortar 15mm thick in CM 1:6 in floors, complete all as specified and directed.

All as per item No 1.38 above but on vertical surfaces such as skirtings, dados and risers to steps etc incl rendering 10mm thick on of brick work or concrete surfaces in cement mortar 1:4 complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 300mm X 450mm X 6-7mm thick as in dado/skirting set and jointed in neat cement slurry and pointed in matching pigment over and including 10mm thick CM (1:4) backing coat Tiles shall be of grade B-III as per IS-13712 (1993) of First quality all as specified & directed

M & L for light shade vitrified ceramic tiles 10mm thick, (Square or rectangular) polished, area of each tile n .exc 0.36 sqm in floors etc set and jointed in near cement slurry and pointed in white or coloured cement to match incl 15mm thick screed bed CM 1:6 all as specified

All as per item No 1.41 above but on vertical surfaces such as skirtings, dado abd rusers to steps etc incl rendering 10mm thick on of brick work or concrete surfaces in cement mortar 1:4 complete all as specified and directed.

Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and directed.

M&L machine cut Kota stone slab 20 to 25 mm thick flooring/landing/ kitchen platform laid and jointed with grey cement slurry incl. rubbing and polishing, over and including 20 mm thick CM 1:3 screed bed complete all as specified and directed.(Note: All exposed side of kota stone slab to be rounding)

Dismantling wall and ceiling boards any thickness including cover fillets complete all as specified and directed.

M&L for 6mm thick AC plain building boards as in ceiling complete all as specified and directed.

S&F 4mm thick coloured textured designer ceiling board (Everest) of size 595X595 mm fixing with screws/clips including Tee grid suspension system of size 600 mm x600 mm type-1 made out of roll framed hot dipped galvanised steel zinc coated of not less than 120 gm/sqm ,main runner shall be 0.3 mm thick of section 24 mmX33 mm cross runner 0.3 mm thick of section 24 mmx25 mm,wall angle shall be 0.63 mm thick of section 24 mmx24 mm grid shall be suspended by 4 mm dia adjustable quick fit hanger rod ,system exposed portion shall be pre painted polyster coated in off white/white in colour complete with material,fixing, jointing etc complete all as specified and directed.

Preparation of new or previously untreated steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamal paint over a coat of red oxide primer complete all as specified.

S&F for 25 mm Stainless Steel curtain rod with fixing bracket and knobs fixed in repairs.

S&F in repair vitreous china wash down water closet pan (pedestral pattern), white including connection trap and to flushing pipe, anti-syphnoge pipe etc complete all as specified and as directed.

S&F 10 ltrs capacity PVC valve less, syphonic action type flusing cistern, low level white with inlet ball valve float and handle including brackets fixed in repairs complete all as specified and directed.

Taking up or down steel tubing and connections of any description and from any position incl cleaning for refixing or removing from site.

15mm bore of pipe

20mm bore of pipe

S&F galvanised steel tubes medium grade together with tube fittings ( such as bents, elbow, tees, short piece,conection, caps plugs and unions etc and fixed with clips wall hooks, wooden plug etc fixed complete to walls, ceilings or in floors etc., any type of pipe all as specified.

15mm bore of pipe

20 mm bore of pipe

S&F in repairs Rotational moulded polyethylene water storage tanks 500 Liters (cylindrical vertical with closed top) hoisted and fixed in position all specified in SSR Part I

All as per item No 1.58 but 1000 Litres capacity complete all as specified and directed.

Cleaning and removing all acale and dirt etc from tanks and moulds of cerculating pipe etc and dispose the all scale dirt, sludge etc where directed and clean the surrounding area of the tank neat and clean of capacity exc 250 ltr and not exc 500 ltr complete all as specified and directed by Engineer-in-charge.

All as per item No 1.60 above but capacity exc 500 ltr and not exc 1000 ltr complete all as specified and directed.

S&F in repairs stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe of 15mm bore all as specified.

S&F in repairs bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe 15mm bore chromium plated (fancy type) all as specified.

S&F in repairs pillar tap, cast copper alloy, with capstan head, chromium plated scrwed down high pressure with or without letter 'Hot' or 'Cold' with long shank and fly nuts screwed for iron pipe of bore 15mm all as specified.

S&F in repairs angle stop valve of cast copper alloy chromium plated (fancy type) screwed for iron pipe of 15mm bore all as specified.

S&F PVC connection size 15 x 600mm with PTMT symet nuts complete all as specified and directed.

S & F sheet glass assembly consisting of 5mm thick sheet glass self wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S & F grating doom 125 mm dia of PTMT complete all as specified and directed.

S&F Viterous china wash hand basin, white, flat back, size 550mm X 400mm including CI brackets complete all as specified and as directed by Engr In Charge fixed as in repairs.

S &F viterous china water closet Squatting Orissa patern white size 580 x 440mm with integral foot rest with P or S trap including etc compete all as specified.(excluding cost of flush tank).

S&F 32 mm dia PVC waste pipe fixed in repairs. Including Cup bracket complete all as specified and directed.

S&F 40 mm dia PVC waste pipe fixed in repairs. Including Cup bracket complete all as specified and directed.

S & F 110mm PVC (SWR) pipes single socketed in any length with bends & rubber ring joints fixed to walls.

S&F 110mm dia PVC (SWR) branch piece single (single 'Y') equal or unequal with acess door.

S & F 75 mm PVC (SWR) pipes single socketed in any length with bends & rubber ring joints fixed to walls.

M & L Marble work 18 to 20 mm thick (table rubbed and plished) in steps, jambs, pillars, windowwcills, cooking platform and like cement mortar (1:4) including in pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble share of following type-Green marble complete all as specified and directed.

S & F in repair 75 mm bore PVC (SWR) branch pieces, single ( equal or unequal), ordinary or inverted ( spigot or socket type) or with parallel branches.

S&F in repairs 75mm bore PVC (SWR) floor trap long body type with grating including jointing with solvent cement.

M&L for preparation of existing treatment and applying One Coat of white wash on wall complete all as specified and dircted.

M&L for preparation of existing treatment and applying One Coat coat of Oil Bound Distemper complete all as specified and dircted.

M & L finishing walls with textured interior / exterior paint of required shade : New Work (Two or more coats applied @ 3.28 ltr/10 Sqm) over and including priming coat of interior / exterior primer applied @ 2.20kg/10 Sqm complete all as specified and directed.

M&L for preparation of existing treatment and applying one coat of white wash on ceilings complete all as specified and directed.

M & L for preparation of old painted wooden surfaces of any description postion and location not otherwise described over 10cms width or girth and applying one coat of synthetic enamel paint (ordinary tint) complete all as specified and directed

M & L for preparation of old painted steel surfaces of any description postion and location not otherwise described over 10 cms width or girth and applying one coat of synthetic enamel paint (ordinary tint) complete all as specified and directed

Removing of existing un-serviceable water proofing treatment , taking down cement plaster etc, of any description and claening of top surfaces of cement concrete flushing out junction of parapet walls and washing down with water complete all as specified and directed.

M&L for water proofing treatment to non accessible RCC roofs by providing 10mm thick screed in CM 1:3 mixed with & including water proofing compound @ 3% by weight of cement & applying one coat of bituminous primer @ 0.30 kg/sqm & laying APP based polymer modified membrane with polyster non woven reinforced of weight not less than 3 kg/sqm 3mm thick with polythene finished sealing with side over laps of 75mm & 100mm laps at the ends of membrane by torch application method & applying two coats of aluminium paint as per the makes approved by the Engr-in-Charge.

M&L PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in, levelling coarse complete all as speificed and directed

S&F in repair 1 mm thick stainless steel plate rack for utensils of size 31"x36"x10" of approved pattern and design complete all as specified and directed.

S & F in repair for fibre glass reinforced tansculent sheet 2mm thick in repair any colour fix to iron frame complete all as specified and directed.

S&Fin repair stainless steel kitchen sink with draining board, made out of 1mm thick sheet, over all size 915 x 460mm with bowl size 410 mm x 330mm x 160mm, including fixing brackets, waste coupling, waste pipe, washers, connecting union etc complete all as specified and directed.

M & L for 2mm thick wallcare putty on walls complete all as specified and directed.

Dismantling asbestos cement (corrugated or semi corrugated, etc) sheets in roof covering complete all as specified and directed.

S & F prepainted galvalume aluminium zinc coating GI base corrugated steel sheet 0.50 mm thick of green colopur having tensile stength of 550 Mpa as in roof covering / clading to wall, fixed with self tapping screws complete all as specified and directed (Note : Corrugation colour and shape of sheet shall be approved by GE

S & F prepainted galvalume aluminum zinc coating GI base plain steel sheet 0.50 mm thick of any colour having tensile stength of 550 Mpa as in ridge, fixed with self tapping screws aincluding neoprane and EPDM washers completed all as specified and directed

S&F in repair Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm- 45gms 32mm bore

S&F roof trusses (framed), trussed purlins crane grantries, rails and fastenings and heavy racket framing (Beam, tee, angle channel or flat sections) incl distance pieces ,cleats etc Fe410-W (Gde-E-250) quality A complete all as specified and directed.

S&F in repair Waste coupling of PTMT (half or full threaded) . (Minimum weight40mm-60 gms) 40mm bore complete all as specified and directed.

yesh construction (BID ID -3336260)

SNEH TRADERS (BID ID -3343149)