Vadnagar Aspirational Toilet under SJMMSVY on EPC basis: Re invitation : Design, Development, Construction and Post completion of 30 years Repair, Operation & Maintenance for Aspirational Public Toilet based on heritage theme on Exterior with all necessary amenities, Electrification, Plumbing Works, with amenities and Supplying, Erecting, Testing & Commissioning Decorative Lighting Including 03-[Three] Years Defect Liability Period for Vadnagar Nagarpalika, Tal: - Vadnagar, Dist.: Mehsana, Gujarat Under SJMMSVY" based on VGF

Schedule - B Abstract

Schedule No. Description Amount (In Rs.)

SCHEDULE - B1 Toilet Block

SCHEDULE - B2 Electrification Work

SCHEDULE - B3 Decorative Lights

SCHEDULE - B4 Amenities

SCHEDULE - B5 Demolition Work

Total Project Cost of 4-Nos of Public Toilet Blocks at Vadnagar under SJMMSVY

Item Description Total Qty. Rate. Unit

No. Amount (Rs.)

Excavation for foundation up to 1.5 m depth including sorting out and stacking of useful

materials and disposing off the excavated stuff up to 50 Meter lead. (C) Hard Murrum

Providing and laying cement concrete 1:4:8 (1- Cement : 4- coarse sand : 8- hand broken

2 stone aggregates 40 mm nominal size) and curing complete excluding cost of formwork in 92.00 2,643.35 cu.m

(A) Foundation and Plinth

Brick work using common burnt clay building bricks having crushing strength not less than

3 35 kg./Sq.Cm. in foundation and plinth in Cement Mortar 1:5. (1- Cement : 5 -fine sand) (A) 160.00 3,898.48 cu.m

Providing and laying ordinary cement concrete 1:2:4 (1- Cement 2- coarse sand : 4- graded

stone aggregates 20 mm nominal size) and finishing smooth with, curing etc. complete

including the cost of formwork but excluding the cost of reinforcement for R.C.C work in (B)

Column, Beam, Wall.

Brick work using common burnt clay building bricks having crushing strength not less than

5 35 kg./Sq.Cm. for brick work in superstructure above plinth level up to floor two level (A) 188.00 4,168.81 cu.m

Modular in Cement Mortar 1:5. (1- Cement : 5 -fine sand) (A) Modular

Filling available excavated earth (excluding rock) in trenches. plinth, sides of foundations

6 etc. in layers not exceeding 20 cm. in depth consolidating each deposited layer by ramming 156.00 136.92 cu.m

Filling in plinth with sand under floors including watering ramming, consolidating and

dressing complete

Providing and laying cement concrete 1:4:8 (1- Cement : 4- coarse sand : 8- hand broken

8 stone aggregates 40 mm nominal size) and curing Complete excluding cost of formwork in 16.00 2,643.35 cu.m

(A) Foundation and Plinth, Flooring work

Providing and laying ordinary cement concrete 1:2:4 (1- Cement 2- coarse sand : 4- graded

stone aggregates 20 mm nominal size) and finishing smooth with, curing etc. complete

including the cost of formwork but excluding the cost of reinforcement for R.C.C work in (A)

Lintel, Beam, Column, Slab.

Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding and

placing in position complete up to floor two level

Providing formwork of ordinary timber planking so as to give a rough finish including

centering shuttering strutting and propping etc. Height of propping and centering below

11 supporting floor to ceiling not exceeding 4 M. and removal of the same for in situ reinforced 1208.00 286.87 Sqm

concrete and plain concrete work in. (B) Flat surfaces such as soffits of suspended floor roof

slabs Landings and the like. (2) Columns, Beam, Lintel, Chajja & Floors etc.

Half brick masonry in common brunt clay building bricks having crushing strength not less

12 than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -coarse sand ) for brick work in Extra 362.00 570.42 Sqm

for brick work in superstructure above floor two in superstructure (B) Conventional

Providing 15mm thick cement plaster in single coat on Rough (Similar) side of single or half

13 brick walls for interior plastering up to floor two level and finished even and smooth 3164.00 165.31 Sqm

including curing (ii) Cement mortar 1:4 (1-cement :4-sand)

Providing 20 mm thick double coat Special cement plaster on Exposed Surface of Wall /

Beam / Column, Interior brick / concrete work for plastering comprising of base coat of

14 mm thick cement plaster in cement mortar (1 Cement : 4 coarse sand) in rough finishing and 1000.00 284.33 Sqm

8 mm thick top coat of cement mortar 1:2 (1 Cement : 2 Coarse sand) finished with trovel

including scaffolding curing etc. complete.

Providing and laying white glazed tiles 6mm thick in flooring treads of steps and landing laid

15 on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand ) finishing with flush 632.00 950.53 Sqm

pointing in white cement.

Providing and laying coloured glazed tiles of the size 300 mm x 200 mm x 8 mm / 300 mm x

450 mm x 8 mm in skirting, risers of steps and dedo on 10 mm. thick cement plaster 1:3 (1

cement : 3 coarse sand) & jointed

with white cement slurry.

Supplying of Steel work, welded in built up sections framed work including cutting, hoisting,

17 fixing in position and applying a priming coat of red lead paint. (D) for MS Jali for window, 1267.20 100.75 kg

up to 25 M. span and 15 M. overall height.

Item Description Total Qty. Rate. Unit

No. Amount (Rs.)

Providing and fixing 30mm thick FACTORY MADE SOLID BOTH SIDE PRELAM PANEL PVC

DOOR SHUTTER consisting of frame made out of M.S. tubes of 19 gauge thickness and size

of 19mm x 19mm for stiles, top and bottom rails. M.S. frame shall have a coat of steel

primer of approved made and manufactures. M.S frame covered with 5mm thick heat

moulded prelim PVC ‘C’ channel of size 30mm thickness, 70 mm width of which 50mm shall

be flat and 20mm shall be tapered in 45 degree Angle on either side forming stiles, and

5mm thick, 95mm wide pream PVC sheet out of which 75mm shall be flat and 20mm shall

be tapered in 45 degree on the inner side ot form top and bottom rail and 115mm wide

18 prelim PVc sheet out of which 75nmm shall be flat and 20mm shall be tapered on both side 89.48 2,236.14 Sqm

to form lock rail, Top, bottom and lock rails shall be provided either side of the panel. 10mm

(5mm x 2) thick 20mm wide cross PVC sheet shall be provided as gap insert for top rail and

bottom rails. Panelling of 5mm thick both side prelim PVC sheet to be fitted in the M.S.

frame welded, sealed to the stiles and rails with 7mm (5mm + 2 mm) thick x 15mm wide

PVC sheet beading on inner side, and joined together with solvent cement adhesive. An

additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the ‘C”

channel using PVC solvent adhesive etc. complete as per direction of Engineering in charge,

manufacture’s specification and Drawing.

Providing and fixing M.S. round or square bars with M.S.flats at required spacing in frames

of Gates / windows and clerestory Gates / windows.

Distempering (Two + One coats) with oil bound washable distemper of approved brand and

manufacture and of required shade on wall surfaces to give an even shade, over and

20 including a priming coat with alkali resistance primer of approved brand after thoroughly 1000.00 104.06 Sqm

brushing the surface and other foreign matter and also including preparing the surface even

and sand prepared smooth.

Finishing wall with water proofing cement paint of on wall surfaces (Two coats) to give an

21 approved brand and manufacture and of required shape even shade after thoroughly 2248.00 65.25 Sqm

brushing the surface to remove all dirt and remains of loose powered materials.

Applying priming coat over new steel and other metal surface after and including preparing

the surface by thoroughly cleaning, oil, grease, dirt and other foreign matter and scoured

with brushes fine steel wood, scrapers and sand paper with ready mixed priming paint

brushing red lead. and Painting three coats on new steel and other metal surface with

enamel paint, brushing, interior to give an even shade including cleaning the surface an

even shade including cleaning the surface of all dirt, dust and other foreign matter.

Providing and fixing water closet squatting Pan (Indian type W.C. Pan) size 580mm and in

Cement Mortar 1:3 (1-Cement : 3-coarse sand)a, pair of white vitreous China 250mm x

130mm x 30mm footrest to long pattern squatting pan water closet (A) Vitreous China.(I)

Long pattern = White colour, 100mm size P or S trap for water closet squatting pan including

jointing the trap with the pan and soil pipe in cement Mortar 1:1 (1-Cement : 1-Fine sand)

(A) Vitreous China, .

Providing and fixing wash down water closet (European type, W.C. Pan) with integral P or S

trap including jointing the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand)

24 (Seal and cover to be measured and paid for separately)(A) vitreous China Pattern : (i) in 16.00 1,648.15 Each

white colour with plastic seat and cover for wash down water closer with C.P. brass hinges

and rubber buffers. (B) Matched colour plastic seal and cover.

Providing and fixing Urinal or approved quality including connecting the Urinal with waste

25 pipe, tap etc. complete. (A) White earthenware flat back or corner type size 430mm x 12.00 1,074.86 Each

Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S. brackets

painted white including setting holes and making good the same but excluding fittings. (A)

26 Vitreous China: (ii) Flat Back washbasin 550 mm x v 400mm size. (i) In white colour with 24.00 1,697.98 Each

C.P. brass waste for washbasin or sink. (B) 40mm dia and M.I. fisher union for washbasin or

sink. (A) 32mm dia.

Providing and fixing C.P. brass towel rail complete with C.P. brass brackets fixed to wooden

plugs with C.P. brass scews.(B) 600mm x 20mm size.

Item Description Total Qty. Rate. Unit

No. Amount (Rs.)

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm

28 distance from wall of standard shape with bracket of the same materials with snap fittings 24.00 142.67 Each

of approved quality and colour, weighing not less than 105 gms.

Providing and fixing 600mm x 450mm bevelled edge mirror of superior glass mounted on

29 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge with C.P. brass screws 20.00 859.41 Each

and washers completed

Supplying and fixing of enamel indication board with Male, Female, PWD figure of not less

than size of 35 cm x 35cm

31 Supplying and Fixing of hanger hook in walls 16.00 250.00 Each

32 Supplying and fixing of indication board engraved in Granite Stone slab 4.00 25,000.00 Each

Construction of 10,000 ltr. Capacity Under Ground Sump with Providing and applying

33 integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC 4.00 62,600.00 Each

structures like water tanks.

Providing and laying cement concrete flooring 1:2:4 (1-cement : 2-coarse sand : 4-graded

34 stone aggregate 20mm nominal size) laid in one layer and finished with a floating coat of 344.00 352.01 Sqm

neat cement. (B) 50mm thick.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE

having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal

bore tube fittings and clamps including making good the wall, ceiling and floor

etc.complete. [D] 32mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE

having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal

bore tube fittings and clamps including making good the wall, ceiling and floor etc.

complete. [C] 25 mm.

Providing and fixing screw down bib taps of following size. (C) Gun metal screw down bib

tap. (i) 15mm dia.

38 Providing and fixing Gun metal check or non-return full way wheel valve. (C) 25mm dia. 16.00 420.63 Each

39 Providing and fixing M.I. / G.I. fisher union (A) 32mm dia. 16.00 78.75 Each

Providing erecting and fixing double coated ISI water tank of required capacity each with all

necessary fittings and connection etc. complete on terrace.

Providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks

and back nuts. (ii) 20mm dia.

42 Providing and fixing brass screw down stop tap. (A) 15mm dia. 16.00 205.83 Each

43 Providing Water connection from the nearest available Points. 4.00 2,500.00 Each

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight

44 C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square 20.00 1,246.92 Each

mouth traps. (B) 150mm x 100mm size P or R type

Providing and fixing cast iron (Spun) Nahni trap of the following nominal diameter of self

45 cleaning design with C.I. screaed down or higned grating including cost of cutting and 16.00 634.17 Each

making good the walls and floor 100mm inlet and 50mm outlet. (C) 100mm dia.

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends

with bricks having crushing strength not less than 35Kg/ Cm2 in C.M. 1:5 C.I. cover with

frame (Light duty) 455mm x 610mm internal dimensions total weight of cover with frame to

be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slab with

1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation

concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a

floating coat of neat cement on walls and bed concrete etc. complete. (iii) Inside

dimensions 600mm x 850 mm and 450mm deep for pipe lines with three or more inlets.

Item Description Total Qty. Rate. Unit

No. Amount (Rs.)

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse sand : 4-graded

stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1-cement : 3- coarse

sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:3 (1-

Cement : 3-coarse sand) finished with a floating coat of neat cement and making channels in

cement concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate 20mm nominal

47 size) finished smooth complete including curing and fasting (i) Inside size 900mm x 1200mm 8.00 19,349.63 Each

and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover

and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With

230mm thick walls of brick masonry using brick having crushing strength not less than 35Kg.

/ Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand)

(2) B type depth 1.50 Metre for 150mm diameter sewer.

Providing and laying (to level or slopes) and jointing with stiff mixture of Cement Mortar in

48 proportion 1:1 Salt glazed stoneware pipes including testing of pipes and joints complete. 160.00 317.28 Rmt

Providing and laying (to level or slopes) and jointing with stiff mixture of Cement Mortar in

49 proportion 1:1 Salt glazed stoneware pipes including testing of pipes and joints complete. 160.00 225.44 Rmt

Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine sand :10-Graded stone

aggregate 40mm nominal size) bedding for stoneware pipes of following internal diameters

with necessary formwork and curing complete. (B) 150mm dia.

Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine sand :10-Graded stone

aggregate 40mm nominal size) bedding for stoneware pipes of following internal diameters

with necessary formwork and curing complete. (A) 100 mm dia

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene

pipes of the following outside Dia. Low density, complete with special flange compression

type fittings, wall chipset.

including making good the wall ceiling and floor. (G)110 mm

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure

pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared

for collar joints including testing of joints complete. (D) 300mm

54 Providing and fixing toilet paper holder. (A) C.P. Brass 16.00 427.99 Each

55 Providing and fixing Hand Dryer 8.00 15,000.00 Each

56 Providing and fixing Sanitary Napkin Machine 4.00 20,000.00 Each

57 Providing and fixing incinerator Machine 4.00 40,000.00 Each

58 Providing and fixing Submersible Pump 4.00 10,000.00 Each

Providing and laying marble stone slab Partition / flooring over 20mm (average)base of

cement mortar 1:6 (1-cement : 6 coarse sand) or L.M. 1:1.5(1- lime putty : 1.5 - coarse sand)

laid and jointed with grey cement slurry including rubbing and polishing complete. (A)

Marble slab 25mm thick

Providing and fixing tiles roofing / Weather shade with manglore tiles including teak reepers

of sizes 50mm x 25mm.

Providing and fixing and carving with heritage and Architectural Look as required on Site

with Indian teak wood and as Directed by Engineer In charge.

2 Electrification Work

Providing, Supplying and fixing all electrical wiring internally or surface mounted completed

with PVC channels/tubes, 5/10/20 Amp Double gang switch, LED tube & Bulb, Spot Light

with all light fixtures and Motion detectors, Exhaust fan and Fresh air fan with all fittings,

vents, Covers and all other necessary electrical items and Fixing etc. completed.

3 Decorative Lights

Item Description Total Qty. Rate. Unit

No. Amount (Rs.)

Providing, supplying, and fixing of outdoor decorative lighting fixtures including all electrical

cabling, connections, mounting accessories, control systems, and instrumentation required

for proper functioning. The scope includes installation, testing, and commissioning of energy-

64 efficient decorative lights as per approved design and specifications, complete in all 4.00 66,000.00 Job

respects. All associated works such as conduit laying, junction boxes, switchgear, anchoring

hardware, and integration with existing electrical panels shall be included if required as per

Providing and fixing of 0.5 Ton split-type inverter air conditioner (minimum 3-star rated)

with both indoor and outdoor units, including refrigerant piping, electrical connections,

copper piping, drain pipe, supports, mounting frame, vibration isolation pads, and all

accessories as required for installation and operation. The work shall also include testing,

commissioning, and handing over in working condition, complete in all respects.

Approved Make: [Daikin / Hitachi / Voltas / Carrier or approved equivalent

Supplying and installing vertical display refrigerator with front glass door, suitable for

showcasing beverages/snacks, with following specifications: Type: Upright vertical

refrigerator with double-layered tempered glass door, anti-fog and UV-protected. Capacity:

Minimum 300–400 litres, suitable for commercial/light commercial use. Finish: External

Body: Powder-coated / stainless steel body in black or silver finish. Internal Liner: Food-

grade white plastic or stainless steel. Door: Self-closing hinged type with lockable handle,

66 clear glass front panel with aluminum frame. Cooling System: Static or fan-assisted cooling. 4.00 1,70,000.00 Each

Operating temperature: +2°C to +8°C. Digital temperature controller and display. Shelves:

Adjustable powder-coated wire shelves (min. 4 nos.). Lighting: Internal LED strip lighting

with auto on/off function. Power: 230V, 50Hz, single phase, energy-efficient (Star-rated /

inverter compressor preferred). Accessories: Lockable castor wheels, drainage tray, and

branding provision as per design.

Approved Makes: Western / Blue Star / Voltas / Elanpro / Trufrost or equivalent

Providing, supplying, and fixing of soft‑drink dispensing machine, including installation of

syrup pumps (hard‑plumbed or cartridge system), CO₂ carbonator, chilled water or ice‑plate

cooling system, dispenser tower or gun, drain line, electric power connection, mounting

frame/supports, and all accessories. The scope includes testing, commissioning, calibration

for portion control, and handing over in complete working. Valves: 4‑8 flavour (push‑button

or lever operated), Cooling: Chilled cold‑plate or built‑in ice bin (capacity 80‑100 lb) Power

Supply: 230 V, 50 Hz, Single Phase condition.

Approved Make: Lancer IBD / Coca‑Cola Freestyle / Approved equivalent

Providing, supplying, and installing a fully automatic commercial tea and coffee vending

machine suitable for continuous use in institutional or office environments. The machine

shall be capable of dispensing at least 2 hot beverages (tea and coffee), with options for

additional flavours such as cardamom tea or cappuccino, depending on model

configuration. The scope includes: Machine with minimum 2 to 4 canister configuration

(multi-lane), Automatic water refill system (bottle-fed or direct line), Digital controls and

68 display panel, Integrated hot water tank and heating system, Dispensing mechanism for 4.00 65,000.00 Each

premix-based or bean-to-cup operation, Initial calibration, testing, and commissioning. One-

time training for operational use. All required accessories such as stand (if needed), water

filter (where applicable), drain pipe, stabilizer (if required), etc.Power Supply: 230V ±10%,

50Hz, Single Phase, Capacity: Minimum 100–300 cups/day (customizable), Warranty:

Minimum 1-year onsite warranty. Approved Makes: Café Desire / Atlantis / Nestlé / Chai

Point or equivalent approved make

Item Description Total Qty. Rate. Unit

No. Amount (Rs.)

Providing, supplying, and installing a commercial-grade stainless steel gas stove (gas top)

with high-efficiency brass burners and heavy-duty cast iron pan supports. The unit shall be

suitable for use with LPG or PNG as per site requirements and equipped with flame control

knobs, drip trays, and anti-skid legs. The scope includes: Fabricated stainless steel body

(minimum 304 grade), 2/3/4 burner configuration (as per site requirement), ISI-marked

brass burners and nozzles, Cast iron pan supports, Integrated drip trays and splash guard (if

applicable), Inlet nipple and pipe connection for gas inlet, Testing and commissioning for

leak-proof operation, Fuel Type: LPG/PNG (as specified), Material: SS 304 body with brass

burners, Warranty: Minimum 1-year warranty on manufacturing defects. Approved Makes:

Bharti / Sarna / Sunrise / Tandoor King / Approved equivalent.

Providing, supplying, and installing of commercial-grade induction cooktop, suitable for

heavy-duty cooking in institutional, restaurant, or pantry settings. The unit shall have high-

efficiency electromagnetic heating technology with temperature and power control

features, durable build, and overload protection.The scope includes: Induction cooktop with

stainless steel body and ceramic/glass top. Minimum 2000W–5000W power rating (as per

site requirement), Multiple power and temperature levels, Overheat and voltage protection,

Digital display with timer settings, Touch or knob controls, Provision for ventilation if

required, Testing and commissioning at site, Power Supply: 230V/415V, 50Hz, Single/Three

Phase (as applicable). Approved Makes: Philips / Cookkart / Sunrise / Electrolux / Panasonic

/ Approved equivalent

Providing, supplying, and fixing of indoor decorative lighting fixtures including all electrical

cabling, connections, mounting accessories and instrumentation required for proper

functioning. The scope includes installation, testing, and commissioning of energy-efficient

71 decorative lights as per approved design and specifications, complete in all respects. All 4.00 50,000.00 Each

associated works such as conduit laying, junction boxes, switchgear, anchoring hardware,

and integration with existing electrical panels or automation systems shall be included if

required as per site.

Providing, supplying, and installing a heavy-duty mixer juicer grinder, suitable for

commercial kitchen use with robust motor capacity, stainless steel jars, and overload

protection. The unit shall be capable of performing blending, grinding (wet and dry), and

juicing operations efficiently. The scope includes: Motor unit with minimum 750W to 1200W

capacity, Stainless steel jars: minimum 3 (wet grinding, dry grinding, and chutney), Juicer

attachment with pulp separator (if applicable), ABS shock-proof body and anti-skid feet,

Overload protection with auto cut-off feature, Power cable with 3-pin plug and accessories

as required, Testing and commissioning at site, Power Supply: 230V, 50Hz, Single Phase.

Approved Makes: Bajaj / Preethi / Philips / Usha / Maharaja Whiteline or approved

Providing, supplying, and installing of a commercial-grade sandwich toaster with non-stick

or cast iron grilling plates, suitable for heavy-duty usage in cafeterias, pantries, or

commercial kitchens. The unit shall be capable of grilling multiple sandwiches

simultaneously, with adjustable temperature control and an insulated body. The scope

includes: Grill Type: Single or double plate (as per requirement), Body: Stainless steel outer

73 body with heat-resistant handles, Heating Plates: Cast iron / non-stick coated, ribbed or flat, 4.00 4,000.00 Each

Features: Adjustable thermostat, indicator lights, auto cut-off, drip tray,

Accessories: Power cord with 3-pin plug, legs/stand if applicable, Installation: Placement,

connection to power, testing and commissioning, Power Supply: 230V ±10%, 50Hz, Single

Phase, Power Rating: Approx. 1500W to 2500W (depending on size and plate type)

Approved Makes: Toastmaster / Skyline / Glen / Kent / Havells / Approved equivalent

Item Description Total Qty. Rate. Unit

No. Amount (Rs.)

Providing, supplying, and installing of commercial-grade OTG (Oven Toaster Grill) for baking,

grilling, and toasting applications in kitchen or pantry settings. The unit shall be equipped

with a temperature-controlled heating system, convection fan (if applicable), timer, and

multiple heating modes (top, bottom, or both). The scope includes: Stainless steel outer

body with heat-resistant glass door, Internal chamber with chrome-plated or stainless steel

racks and crumb tray, Heating elements (top and bottom) with separate temperature

controls, Timer (minimum 60-minute range) with auto shut-off and indicator, Accessories:

baking tray, grill rack, skewer rods, crumb tray, Installation, testing, and commissioning at

site, Capacity: 30 to 60 litres (as per requirement)

Power Supply: 230V, 50Hz, Single Phase, Power Rating: Approx. 1500W–2200W.

Preferred Makes: Morphy Richards / Bajaj / Philips / Borosil / Wonderchef / Approved

Providing, supplying, and installing of a commercial-grade microwave oven suitable for

cooking, heating, and defrosting applications in office pantries, institutional kitchens, or

food service areas. The unit shall be durable, energy-efficient, and equipped with advanced

safety and control features. The scope includes: Stainless steel inner and outer body, Digital

control panel with preset cooking modes and power levels, Minimum 5 power levels with

75 timer settings, Cavity capacity: 25–30 litres (or as specified), Turntable / flatbed heating 4.00 25,000.00 Each

system, Accessories: Glass tray, roller ring, starter kit (if any), Installation, testing, and

commissioning at site, Power Supply: 230V ±10%, 50Hz, Single Phase, Power Rating:

800W–1200W (Microwave Output), Type: Microwave / Microwave with Grill / Microwave

with Convection (specify).

Preferred Makes: Panasonic / IFB / LG / Samsung / Bosch or approved equivalent

Supplying, fabricating, and installing custom-designed reception table with counter top,

including all necessary supports, storage units, and footrest, as per approved design and

drawings. The reception table shall include the following specifications: Top Surface (Work

Top and Transaction Counter): 18mm thick marine-grade plywood finished with 6mm thick

solid surface (e.g., Corian or equivalent) in approved shade, including edge rounding and

seamless joints. Structure and Vertical Panels: Internal frame of 19mm BWP-grade plywood,

laminated with 1mm thick high-pressure laminate (HPL) in approved wood grain / solid color

finish. Drawer Units / Storage (if applicable): Soft-close telescopic channels, 18mm BWP ply

with both internal and external surfaces finished in 1mm HPL, with 0.8mm white laminate

76 for inner faces.Modesty Panel (Front Cladding): Finished in back-painted toughened glass 4.00 2,00,000.00 Each

(6mm thick) / decorative fluted MDF panels or acrylic panel in approved color and pattern.

Edge Banding: All exposed ply edges to be finished with PVC edge banding tape (2mm) of

matching shade. Hardware: All necessary hardware including SS screws, locks, handles, wire

manager, CPU trolley, footrest, etc., of approved make (Hettich / Hafele / equivalent). Base

Skirting: 75mm high brushed stainless steel skirting (grade SS304) with groove detail,

finished flush to flooring. Electrical Provision: Necessary cutouts and concealed conduits for

cable routing, sockets (1 Nos. 6A + 1 Nos. USB charger point), with wiring termination to

junction box below table. Note: All materials to be used shall be of approved brand and

shade. Shop drawings must be submitted for client/architect approval prior to fabrication.

5 Demolition Work

Demolition including stacking of serviceable materials and disposal of unserviceable

materials with all lead and lift. (i) R.C.C. work

Demolition of Brick work and stone masonry including stacking of serviceable materials and

disposal of unserviceable materials with all lead and lift.(ii) In Cement Mortar

Dismantling tiled of stone floors laid in mortar including stacking of serviceable materials

and disposal of unserviceable materials with all lead and lift.

Dismantling wood work, wrought framed and fixed in frames trusses including stacking the

materials with all lead and lift.

Dismantling doors, windows, ventilators etc. (wood or steel) shutters including chowkhats

81 architraves, holdfasts and other attachment etc. complete and stacking them within all lead 20.00 191.85 Each

and lift. (i) Not exceeding 3 Sq.M. in area.

Item Description Total Qty. Rate. Unit

No. Amount (Rs.)

Dismantling doors, windows, ventilators etc. (wood or steel) shutters including chowkhats

82 architraves, holdfasts and other attachment etc. complete and stacking them within all lead 10.00 257.48 Each

and lift. (ii) Exceeding 3 Sq.M. in area.

Dismantling C.I. pipes G.S.W. pipes abd A.C. rain water pipes with fittings and clamps

including stacking the materials with all lead and lift ( for any dia, of pipe)

Dismantling sanitary fittings like wash basin. W.C. pan Indian and European type, flushing

tank etc. including stacking the materials with all lead and lift.

Structural steel work (Confirming to IS 4923-1997) riveted, bolted or welded in built-up for

all type sections, in framed work, including cutting, hoisting, fixing in position and applying a

priming coat of approved steel primer all complete as per the structural designs and

directions of Engineer in charge.