REPAIRS/PAINTING TO STEEL FURNITURE INCLUDING CHARPOY GI PIPE AT BARRACKPORE UNDER GE BARRACKPORE

Amount

RE-CANNING OF CHAIR VARANDAH WITH CANE PLASTIC (DRG NO.FD-19, FD-256):- :-

Removing of existing old unserviceable cane plastic from chair verandah and re-canning the same with new cane plastic (white colour) 6mm width of approved quality including painting with synthetic enamel paint white all as shown on drawing.

REPAIRS TO CHAIR VERANDAH (DRG NO.FD/MAP-II/15):- :-

SEAT Removing of old unserviceable PVC seat from its existing position of chair verandah and replace the same by supply and fixing with new PVC seat 4mm thick and grooves 90X10mm 10 Nos on seat all as shown on drawing or directed by Engineer-in-charge. (Make:Amco/Harmoney/Comfo as approved)

BACK Removing of old unserviceable back PVC back from its existing position of chair verandah and replace the same by supply and fixing with new PVC 4mm thick back to make completely functional rest all as shown on drawing or directed by Engineer-in-charge. (Make:Amco/Harmoney/Comfo as approved)

HARD RUBBER SHOE Removing of each decayed hard rubber shoe from its existing position of chair varandah and replace the same with new hard rubber shoe all as shown on drawing and directed by Engineer-in-Charge.

PAINTINGS OF CHAIR VERANDAH (DRG NO: FD/MAP-II/15) M&L for applying spray painting two coats with synthetic enamel (white) paint over a coat of red oxide primer with spray gun after removing of existing old worn out paint by any means with proper treatment from chair verandah complete all as directed and shown on drawings.

REPAIRS TO TEAPOY VERANDAH FOR THE FOLLOWING (DRG NO.FD-35, FD-383, FD-208):-

TOP Removing decayed top from its existing position and replace the same with new top made out from 18/19mm thick Prelaminated Particle board (exterior Grade) Grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick well seasoned second class hard wood beading all round the edging provide middle stiffener at the bottom 100mm high between the lower short side rails and provide PVC shoes 25mm dia and 25mm high shall be screwed to bottom of all legs all as shown on drawing.

HARD RUBBER SHOE Removing of each decayed hard rubber shoe from its existing position of Teapoy varandah (FD-35, FD-283, FD-208), Chair CB Steel with arm (FD-75M), Chair CB without arm (FD-75M) and replace the same with new hard rubber shoe all as shown on drawing and directed by Engineer-in-Charge.

PAINTING TO TEAPOY VERANDAH M&L for applying two coats of synthetic enamel (white) paint with spray gun to frame of teapoy verandah including preparation of surfaces complete all as specified and directed.

REPAIR OF ALMIRAH LARGE AND MEDIUM STEEL (DRG NO.FD-67, FD-1032, FD-1033, FD-1031, FD-1034):-

LEGS S&F for new leg made out from MS sheet 1.6mm thick and applying one coat of red oxide zinc chrome primer over two coats of synthetic enamel paint with spray painting by the spray gun after removing of each old worn out legs from its existing portion of Almirah large steel with shelves and Almirah medium steel with shelves and replace the same complete all as specified and directed and as shown on drawing.

HANDLES S&F for new handle made out from mild steel over chromium plated of size 150mm size and weight of each handle should not be less than 185gm of existing pattern after removing of old unserviceable / broken handle from its existing position of almirah large steel with shelves and almirah medium steel with shelves and replace same complete all as specified and directed and as shown on drawing.

LOCKS S&F for new brass, six lever (Make : Godrej) lock with steel CP duplicate keys, weight of each lock should not be less than 260gm after removing of old unserviceable lock from its existing position of almirah large steel with shelves and almirah medium steel with shelves and replace same complete all as specified and directed and as shown on drawing.

SHELVES FOR ALMIRAH LARGE WITH SHALVES STEEL (Drg No. FD-67(M), FD-1031 & FD-1032). S&F for new shelf made out of MS Sheets of 1.00mm thick and applying one coat of red oxide zinc chrome primer over two coats of synthetic enamel paint with spray painting by spray gun after removing of old worn out shelf from its existing portion of almirah large steel with shelves and replace same complete all as specified and directed and as shown on drawing.

SHELVES FOR ALMIRAH MEDIUM STEEL WITH SHALVES (Drg No. FD-67(M), FD-1031 & FD-1032). S&F for new shelf made out of MS Sheets of 1.00mm thick and applying one coat of red oxide zinc chrome primer over two coats of synthetic enamel paint with spray painting by spray gun after removing of old worn out shelf from its existing portion of almirah medium steel with shelves and replace same complete all as specified and directed and as shown on drawing.

PAINTINGS OF ALMIRAH LARGE STEEL WITH SHALVES (Drg No. FD-67(M), FD-1031 & FD-1032). M&L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from almirah large steel with shelves complete all as directed shown drawings.

PAINTINGS OF ALMIRAH MEDIUM STEEL WITH SHALVES (Drg No. FD-67(M), FD-1031 & FD-1032). M&L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from almirah medium steel with shelves complete all as directed shown drawings.

PAINTINGS OF BOOK SHELF OPEN LARGE STEEL (Drg No.FD-69) M&L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from book self open large steel complete all as directed shown drawings.

PAINTINGS OF BOOK SHELF OPEN SMALL STEEL(Drg No.FD-69) M&L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from book self open small steel complete all as directed shown drawings.

PAINTINGS OF TABLE OFFICE CLERK STEEL (Drg No.FD-84) M&L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from able office clerk steel complete all as directed shown drawings.

PAINTINGS OF CHAIR CB STEEL WITH ARMS [Drg No.FD-75(M)] M&L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from Chair CB steel with arm complete all as directed shown drawings.

PAINTINGS OF CHAIR CB STEEL WITHOUT ARMS[Drg No.FD-75(M)] M&L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from Chair CB steel with out arms complete all as directed shown drawings.

PAINTINGS OF LOCKER STEEL(GE/BKP/02/07) M&L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from Locker steel complete all as directed shown drawings. .

REPAIR OF CHARPOY GI PIPE (DRG NO.FD-220 AND BKP/TD/168) :-

LEGS M&L for 32mm bore (medium grade) GI tubing leg (ISI marked) of charpoy after removing of old unserviceable leg of charpoy GI pipe from its existing position all as shown on drawing.

LONG RAIL M&L for 32mm bore (medium grade) GI tubing of long rail (ISI marked) size of 1884 mm long of charpoy GI after removing of old unserviceable long rails of charpoy GI pipe from its existing position all as shown on drawing cut to required length of and threading at both ends all as shown on drawing.

SHORT RAIL M&L for 32mm bore (medium grade) GI tubing of short rail (ISI marked) cut to required length of 900 mm long and threading at both ends all as shown on drawing.

ELBOW GI M&L for 32mm bore 3 way GI elbow weight of each GI elbow should not less than 480gms as per ISI specification all as shown on drawing.

CHECK NUT S&F for check nut for fixing the top with charpoy GI all a shown on drawing

PLY TOP 12MM THICK S&F for 12mm thick BWR grade, type BB, both sides commercial ply wood (7 Nos of ply) with 6mm thick well seasoned teak wood duly polished found at round the edging of the top and beading required 4mm dia 65mm long counter shank machine nut, bolt, washer on top including removing of existing top all as directed by Engineer- in -charge. (Make of Ply wood : Century Ply/Greenply/National ply/Kit ply as approved)

MIDDLE STIFFENER M&L for middle stiffener made out of 25 mm GI (medium grad) 900 mm long after removing of old unseriviceable stiifener from its existing position complete all as specified and shown on drawing.

REPAIR OF CHAIR CB STEEL WITH ARMS [DRG NO.FD-75(M)]:-

WOODEN FRAME SEAT S&F for canned with wooden seat frame made out from well seasoned teak wood duly canned as per Godrej pattern with new plastic cane of 2mm to 2.5mm wide half round oval shape for caning and 4mm wide of half round oval shape cane for bedding & applying two coats of black polish after removing of unserviceable /decayed seat frame from existing portion from chair CB steel with arm as replaced all as directed and shown on drawing.

WOODEN FRAME BACK S&F for canned with wooden back frame made out from well seasoned teak wood duly canned as per Godrej pattern with new plastic cane of 2mm to 2.5mm wide half round oval shape for caning and 4mm wide of half round oval shape cane for bedding & applying two coats of black polish after removing of unserviceable /decayed back frame from existing portion from chair CB steel with arm as replaced all as directed and shown on drawing.

WOODEN ARM FOR CHAIR CB STEEL WITH ARMS S&F for new arm made out from well seasoned teak wood and apply two coats of black polish including removing broken arm from its existing portion of chair CB steels with arm all as directed and shown on drawing.

STIFFENER FOR CHAIR CB STEEL WITH ARM S&F for new MS flat of stiffener size 520mmx15mmx4mm by welding including two coats of synthetic (Olive Green) paint over one coat of red oxide zinc chrome primer including removing of old worm out MS cleat from its existing position from chair CB steel with arm complete all as directed and shown on drawing.

REPAIR OF CHAIR CB STEEL WITH OUT ARMS [DRG NO.FD-75(M)]

WOODEN FRAME SEAT S&F for canned with wooden seat frame made out from well seasoned teak wood duly canned as per Godrej pattern with new plastic cane of 2mm to 2.5mm wide half round oval shape for caning and 4mm wide of half round oval shape cane for bedding & applying two coats of black polish after removing of unserviceable /decayed seat frame from existing portion from chair CB steel without arm as replaced all as directed and shown on drawing.

WOODEN FRAME BACK S&F for canned with wooden back frame made out from well seasoned teak wood duly canned as per Godrej pattern with new plastic cane of 2mm to 2.5mm wide half round oval shape for caning and 4mm wide of half round oval shape cane for bedding & applying two coats of black polish after removing of unserviceable /decayed back frame from existing portion from chair CB steel without arm as replaced all as directed and shown on drawing.

STIFFENER S&F for new MS flat of stiffener size 420mmx15mmx4mm by welding including two coats of synthetic (Olive Green) paint over one coat of red oxide zinc chrome primer including removing of old worm out MS cleat from its existing position from chair CB steel without arm complete all as directed and shown on drawing.

REPAIRS TO COMPUTER CHAIR/REVOLVING CHAIR WITH ARMS (DRG NO - TP &FD/E6/MAP/01 )

WHEEL Removing of old unserviceable revolving wheel from its existing position of computer chair and revolving chair and replace the same by supply and fixing with revolving wheel PVC 40mm.to make completely functional rest all as shown on drawing or directed by Engineer-in-charge.

HYDRAULIC SYSTEM Removing of old unserviceable hydraulic system from its existing position of computer chair and revolving chair and replace the same by supply and fixing with new hydraulic system to make completely functional rest all as shown on drawing or directed by Engineer-in-charge.

BASE Removing of old unserviceable base from its existing position of computer chair and revolving chair and replace the same by supply and fixing with new base to make completely functional rest all as shown on drawing or directed by Engineer-in-charge.

SEAT Removing of old unserviceable seat from its existing position of computer chair and revolving chair and replace the same by supply and fixing with new seat to make completely functional rest all as shown on drawing or directed by Engineer-in-charge.

BACK Removing of old unserviceable back from its existing position of computer chair and revolving chair and replace the same by supply and fixing with new back to make completely functional rest all as shown on drawing or directed by Engineer-in-charge.

ARMS Removing of old unserviceable arms from its existing position of computer chair and revolving chair and replace the same by supply and fixing with new back to make completely functional rest all as shown on drawing or directed by Engineer-in-charge.

REPAIR TO BOOK CASE STEEL (DRG NO. FD-1028):-

SHUTTER Removing of old unserviceable shutter from its existing position of book case steel and replace the same with new shutter as shown on drawing or directed by Engineer-in-charge.

SHUTTER GLASS Removing of old unserviceable shutter glass from its existing position of book case steel and replace the same with new shutter glass as shown on drawing or directed by Engineer-in-charge.

HANDLE Removing of old unserviceable handle from its existing position of book case steel and replace the same with new handle as shown on drawing or directed by Engineer-in-charge.

LOCK Removing of old unserviceable lock from its existing position of book case steel and replace the same with new lock 6 lever brass all as shown on drawing or directed by Engineer-in-charge. (Make : Godrej/Link as approved)

PAINTINGS OF BOOK CASE STEEL (Drg No.FD-1028) M&L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from book case steel complete all as directed shown drawings.

REPAIRS TO TABLE OFFICE CLERK STEEL (DRG NOFD-84, FD-381, FD-1004):-

LEG Removing of old unserviceable leg from its existing position and replace the same with new leg made out of MS square pipe 25mm 16 gauge all as shown on drawing.

DRAWER Removing of old unserviceable drawer from its existing position and replace the same with new drawer made out of 20 gauge MS sheet all as shown on drawing.

LOCK & KEYS Removing of old unserviceable lock of table office clerk steel and supply and fixing with new brass six lever Godrej pattern lock with steel CP duplicate keys all as shown on drawing. (Make : Godrej/Link as approved.)

TOP Removing decayed top from its existing position and replace the same with new top made out from 18mm thick veneered particle board (exterior grade), grade-I quality, with commercial veneers on both sides with 1.00mm thick plastic laminated sheet (plain & wood grain)pasted over particle board with approved synthetic resin adhesive with 6mm thick well seasoned second class hard wood beading all-round the edging all as shown on drawing. (Make of Ply wood : Century Ply/Greenply/National ply/Kit ply as approved)

REPAIRS TO TABLE OFFICE OFFICER STEEL (DRG NO.FD-84, FD-1003):-

LEG Removing of old unserviceable leg from its existing position and replace the same with new leg made out of MS square pipe 25mm 16 gauge all as shown on drawing.

DRAWER Removing of old unserviceable drawer from its existing position and replace the same with new drawer made out of 20 gauge MS sheet all as shown on drawing.

LOCK & KEYS Removing of old unserviceable lock of table office clerk steel and supply and fixing with new brass six lever Godrej pattern lock with steel CP duplicate keys all as shown on drawing. (Make : Godrej/Link as approved.)

TOP Removing decayed top from its existing position and replace the same with new top made out from 18mmthick veneered particle board (exterior grade), Grade-I quality, with commercial veneers on both sides with 1.00mm thick plastic laminated sheet (Plain & wood grain) pasted over particle board with approved synthetic resin adhesive with 6mm thick well seasoned second class hard wood beading all-round the edging all as shown on drawing. (Make of particle board : Century Ply /Greenply/ National ply/Kit ply as approved)

PAINTINGS OF TABLE OFFICE OFFICER STEEL(DRG NO.FD-84, FD-1003):- M&L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from table office officer steel complete all as directed shown drawings.

REPAIRS TO LOCKER STEEL (FD-257& GE/BKP/02/07):-

LEGS M&L after removing of each old worn out legs from its existing position of locker steel and replace the same by supply and fixing with new leg made out from MS sheet 1.6mm thick and applying one coat of red oxide zinc chrome primer over two coats of synthetic enamel paint with spray painting, complete all as specified & directed and as shown on drawing.

HINGES Removing of old unserviceable hinges from its existing position and replace the same with new hinges all as shown on drawing.

HANDLES S&F for 100mm long aluminium handle of existing pattern after removing of old unserviceable/broken handle from its existing position of locker steel complete all as directed.

HASP & STAPLE S&F for 75mm long hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with steel wood screws.

HANGING ROD Removing old broken hanging rod from its existing position and replace the same with new hanging rod made out from 20mm external dia aluminium anodized conduit with a pair of sockets all as shown on drawing.

REPAIRS TO TABLE DINING ORS STEEL (DRG NO.FD-165):-

LEG Removing of old unserviceable leg from its existing position and replace the same with new leg made out of MS square pipe 25mm 16 gauge all as shown on drawing.

TOP Removing of decayed top from its existing position and replace the same with new top made out from 18mm thick veneered particle board (exterior grade), Grade-I quality, with commercial veneers on both sides with 1.00mm thick plastic laminated sheet (Plain & wood grain) pasted over particleboard with approved synthetic resin adhesive with 6mm thick well seasoned 1st class hard wood (Teak/Seasam) beading all-round the edging all as shown on drawing. (Make of Ply wood : Century Ply/Greenply/National ply/ Kit ply as approved)

PAINTING OF TABLE DINING ORS STEEL(FD-165) M&L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from table dinning ORs steel complete all as directed shown drawings.

REPAIRS TO CHAIR SCHOOL WITH HAND BOARD (DRG NO.FD/E6/MAP/05):-

SEAT & BACK Removing of old unserviceable seat & back from its existing position and replace the same with new seat & back made out of blow plast or equivalent approved by E-in-C’s Branch all as shown on drawing.

HAND BOARD Removing of old unserviceable hand board from its existing and replace the same with new hand board made out from 18mm thick pre laminated particle board exterior grade-1 hinged at right hand side of chair arm screwed to 25mm dia MS pipe inserted in 20mm dia MS rod welded to frame . Standard PVC edging 1.6mm thick shall be provided all-round the hand board, rest all as shown in drawing.

BASKET(JALI) Removing of old unserviceable steel basket (Jali) from its existing position and replace the same with new basket (Jali) made of 6mm MS rod all as specified and shown on drawing

REPAIRS TO CHARPOY FOLDING IP HARD TOP (DRG NO.FD/388(R):-

TOP Removing of old unserviceable top from its existing position and replace the same with new top of 9 mm thick BWR Phenoled commercial plywood (un-polished) cut into two pieces to facilitate folding of bed all as shown on drawing. (Make of Ply wood : Century Ply/Greenply/National ply/Kit ply as approved)

FLAT IRON Removing of old unserviceable flat iron from its existing position and replace the same with new mild steel flat iron of size 220mmx60mmx32mm cut to shape and bent @ 150 to avoid fouling with leg all as shown on drawing

REPAIRS TO TABLE BED SIDE (DRG NO.FD/E6/MAP/15(R):

TOP Removing decayed top from its existing position and replace the same with new 18/19mm thick Prelaminated Particle board (exterior Grade), grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination. Standard PVC edging 1.6mm thick shall be provided all-around the top of table bed side all as shown on drawing. (Make of Ply wood : Century Ply/Greenply/National ply/Kit ply as approved)

BACK Removing decayed each back of table bed side from its existing position and replace the same with new back made out from 6mm thick plywood (five Nos of ply), type BB, BWR grade of required size all as shown on drawing. (Make of Ply wood : Century Ply/Greenply/National ply/Kit ply as approved)

DRAWER Removing decayed drawer and replace the drawer made out from 12mm thick pre-laminated particle board (exterior grade), grade-I quality, one side decorative of front, side and back , bottom shall be made out from 6mm thick ply wood (five Nos of ply), type BB, BWR grade of required size as approved by Engineer-in-Charge and rest all as shown on drawing. (Make of Ply wood : Century Ply/Greenply/National ply/Kit ply as approved)

HANDLES S&F for 100mm aluminium handle of existing pattern after removing of old unserviceable / broken handle from its existing position complete all as directed.

HARD RUBBER/PVC RING Removing of each decayed hard rubber/PVC ring from its existing position of Table bed side and replace the same with new hard rubber/PVC ring all as shown on drawing and directed by Engineer-in-Charge.

REPAIRS TO HOT FOOD TROLLEY (DRG NO.FD-133 (M)):

TUBULAR HEATING ELEMENT S&F for tubular heating element of 1250 Volt, 240 AC/DC of hot food trolley after removing of old unserviceable heating element complete all as directed and shown on drawing.

RECEDING DOOR S&F for new receding door (stainless steel) of hot food trolley (as per drawings) after removing of old unservicebale receding doors complete all as directed and shown on drawing.

RACK S&F for new movable refrigerator type stainless steel rack after removing of old unservicebale stainless steel rack complete all as directed and shown on drawing.

MULTI-STAGE ROTARY SWITCH M&L for new multi-stage rotary switch for heat control of hot food trolley after removing of old unservicebale multi-stage rotary switch complete all as directed and shown on drawing.

FOOD VESSLES S&F for new stainless steel food vessles of 200mm dia wide and 200mm deep with dud settings of hot food trolley after removing of old unservicebalestainless steel food vessles complete all as directed and shown on drawing.

WHEEL Removing of old unserviceable revolving wheel from its existing position of hot food trolley and replace the same by supply and fixing with revolving rubber wheel ball bearing type 200mm dia to make completely functional rest all as shown on drawing or directed by Engineer-in-charge.

M/S NEHAL ENTERPRISES

BANERJEE ENTERPRISE

M/S PAUL CONSTRUCTION

M/S Manna Construction

S S ENTERPRISE

PIONEER TRADING

TIMBA

TAMALIKA ENTERPRISE