PROVISION OF WAITING AREA BETWEEN MEDICAL OPD AND ENT OPD BLDG NO P108 LIQUID MEDICAL OXYGEN GAS STORAGE AREA AT INHS KALYANI HARDSTANDING IN FRONT OF BUILDING NO P 150 AT OLD NAUSENABAUGH RCC DRAIN TO CHANNEL THE FLOW OF DRAIN WATER FROM KRANTHI

Amount

Excavating post holes or similar holes, each not exceeding 0.5 Cu. M, getting out in hard / dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 M and making good surface complete all as specified and as directed.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in soft / loose soil complete all as specified and as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick with soils complete all as specified and as directed.

Removing Excavated spoil to a distance execeeding 1.50 km but not exceeding 5 KM and depositing where directed at a level not exceeding 1.50m above the starting point complete all as specified and as directed.

M&L for PCC 1:3:6, Type C2 ( using 40mm graded aggregates) as in bed concrete for foundation etc complete all as specified and as directed.

S&F mild steel hand rails, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

S & F mild steel work as in tubular trusses, trussed purlins and tubular posts including special shaped washers etc., complete using ERW or induction but welded tubes confirming to IS 1161- 1979 grade St 240 with one shop coat of zinc chromate primer paint at contractor's work shop before fabrication complete all as specified and as directed.

M&L for MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment steel of Fe 410-W (Gde E250) quality-B complete all as specified and as directed.

S & F Prepainted Galvalume Aluminium Zinc Coating GI based Plain Steel Sheet 0.5mm thick of any having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws all as specified and as directed.

Supply and Fix Pre-painted galvalume aluminum zinc coating GI based corrugated sheet of 0.50 mm thick[TCT] of any having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed. MAKE : M/s TATA BLUE SCOPE, M/s LLOYD INSULATIONS INDIA LTD, M/s BUILD TECH/ JINDAL

M & L for one coat of Red Oxide Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

Demolition of Unreinforced Cement Concrete any description and in any position not otherwise specifically provided for and and removing rubbish to out side MD land complete all as specified and as directed.

Material and Labour for Walling of random rubble [ KONDALITE STONE], uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and as directed.

Material and Labour for Brick work with fly ash bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for RCC 1:1.5:3 Type A1 (Nominal mix) (using 20mm graded granite stone aggregates) as in Chajjas complete all as specified and as directed.

Use and waste formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and as directed.

M&L for RCC 1:1.5:3 Type A1 (Nominal mix) (using 20mm graded granite stone aggregates) as in Beams, lintels and for encasing MS tubes etc., complete all as specified and as directed.

Use and waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed.

M&L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and as directed.

M&L for Mild steel TMT bars 5 to 10 mm dia., and over cut to length, bent to shape required, as in stirrups, spacers and binders including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and as directed.

M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 and finished even and smooth without using extra cement including mixing of water proofing compound complete all as specified and as directed. Note: Water proofing compound shall be measured and paid separately under relevant item

M&L for Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparing newly plastered surfaces and applying two coats of distemper oil emulsion over one coat of alkali resistant primer on walls complete all as specified and as directed. Make Distemper : Asian / Nerolac / Berger ( All are 1st quality)

M&L for preparing new wall surfaces in any location and applying two coats of exterior weather proof paint over a coat of primer complete all as specified and as directed. Make : Apex Ultima from Asian Paints / All Guard from Berger, Weather Shield Max Exterior Acrylic ICI Dulux

M & L for 100 mm thick, PCC 1:4:8, Type D-2, using 40mm graded aggregate as in Sub base for flooring complete all as specified and as directed.

M & L for 30 mm thick, PCC 1:2:4, Type B-1, using 20mm graded aggregate as in Sub base for flooring complete all as specified and as directed.

M & L for Vitrified ceramic tiles light shade 10 mm thick (Square/ Rectangular) polished, area of each tile not exceeding 0.36sqm in floors etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match including screed bed or bedding layer in cement mortar 1:6, 15 mm thick, complete all as specified and as directed. Make : Johnson / Nitco / Asian Granito / Varmora / Orient Bell

S&F Glazed coloured ceramic tiles in vertical surface 300x450x6 to 7mm thick ,set and jointed in neat cement slurry and pointed in white or cloured cement over and including 10mm thick backing coat CM of 1:3 complete all as specified and as directed. Note : Rate includes for cutting for offsets etc Make : Johnson / Kajaria / Orient / Cera / Asian

S & F Aluminium anodised snap grid frame work for false ceiling of grid size 605 x 605 mm with Aluminium "T" section of size 38 x 25 x 1.50 mm thick for main runners, 25 x 25 x 1.5 mm thick for cross runners and angle of size 25 x 25 x 1.50 mm thick along the walls suspended with and including 4 mm dia., Galvanized mild steel wire (as in suspenders of ceiling members fixed in proper position) including providing and fixing Gypsum Board 12 mm thick in ceiling fixed with screws as per manufacturer's instructions and applying two coats of plastic emulsion paint complete all as specified and as directed. Make of Gypsum board : Saint Gobain/ Gypsum India

S&F Aluminium frame for doors, door shutters, windows, ventilators, fixed partitions etc., with one or more rebates with powder coating of minimum 50 micron thick including joining cleat for fixing etc., complete all as specified and as directed. Make : Jindal / Indal / Hindalco

S & F Anodised Aluminium window and ventilator shutters, sliding type without sash bar, aluminum section weighing 0.55 Kg/ RM including necessary joining cleats, glazing clips, rubber packing, anodised aluminum snap beading, screws, anodised aluminum fittings such as suitable handle (1 No.) etc., complete all as specified and as directed. Make: HINDALCO / INDALCO/JINDAL

S & F 125mm long medium weight Stainless Steel Butt hinges complete all as specified and as directed.

S&F Aluminium extruded section body Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and as directed. Make : Godrej / Everite / Priya

S & F 7 mm thick Aluminium grill of make "Deco grill" and DG - 104 model fitted in to suitable Aluminium channel and fixed to windows / ventilators complete all as specified and as directed. Make : Jindal / Indal / Hindalco

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples / wooden beading complete all as specified and as directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

S & F 12 mm thick, Prelaminated Particle Board, interior grade, prelaminated on both Sides with Decorative Choice Lamination , fixed to aluminium frame work / shutters complete all as specified and as directed. Make : Anchor / Novopan / Deco Board / Bhutan Board / Kitply / Eco Board / Archidlam / Asis / Greenply Industries

Demolition of Unreinforced Cement Concrete in ground floors and Pavings not exceeding 15cm thick [below or above ground level] and removing rubbish to out side MD Land complete all as specified and as directed.

S&F mild steel angles, bars, flats / round / square etc., as in supports for stiffening of fencing, wall ties, hold fasts, clamps and similar small articles conforming to Fe 410-W Grade E-250 complete all as specified and as directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n. exc. 5cm long with dia of neck 5 to 10 mm complete all as specified and as directed.

Supply only 4mm dia PVC coated GI wire chain link fencing of any size mesh complete all as specified and as directed.

Fixing only PVC Coated chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and as directed.

S & F Framed work such as in gates, grills, gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

M & L for loose filling with broken stone boulders of gauge 40mm to 80mm deposited, spread complete all as specified and as directed.

Surface Excavation not exceeding 30 Cm deep and averaging 15 Cm deep and getting out in Soft/ Loose soil complete all as specified and as directed.

M & L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and leveled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M &L for 100 mm thick Cement concrete type B2, 1:2:4 (using 40 mm graded stone aggregate) in flooring/ hard standing and finishing the concrete surface even and fair without using extra cement complete all as specified and as directed.

M & L for forming Contraction [Dummy] Joint 65 mm Deep X 10 mm Wide filled with Sealing Compound Grade "A" complete all as specified and directed.

M&L for PCC 1:3:6, Type C2 ( using 40mm graded aggregates) as in bed concrete for foundation etc complete all as specified and as directed.

M&L for Reinforced Cement Concrete (Nominal Mix) Type A1, 1:11/2:3 (using 20 mm graded stone aggregate) as in foundations, footing for columns, plinth beams, bases for columns and the like complete all as specified and as directed.

M&L for Reinforced Cement Concrete (Nominal Mix) Type A1, 1:11/2:3 (using 20 mm graded stone aggregate) as in columns, piers, posts and the like complete all as specified and as directed.

M&L for Reinforced Cement Concrete (Nominal Mix) Type A1, 1:11/2:3 (using 20 mm graded stone aggregate) as in walls, retaining walls ballast walls and the like complete all as specified and as directed.

Use and waste of Fair finished flat Form work to sides of concrete foundations, rafts, plinth beams and similar work, vertical or batter complete all as specified and as directed.

Use and wasted formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed.

Use and waste of Fair finished flat Form work to faces of retaining walls, parapets, staircase railings and similar work, vertical or batter complete all as specified and as directed.

S&F Rolled Mild steel as in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe-290 (Gde E-165) complete all as specified and as directed.

M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement including mixing of water proofing compound complete all as specified and as directed. Note: Water proofing compound shall be measured and paid separately under relevant item

M&L for rendering 5mm thick in cement mortar (1:4) on ceiling finished even and smooth without using extra cement complete all as specified and as directed

M&L for Preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed.

Supply only Integral water proofing compound [ISI marked] complete all as specified and as directed. Make : Acco proof / Impermo / Lik proof / Scott No. 1

M&L for two coats of synthetic enamal paint over a coat of red oxide zinc chrome primer on new steel surfaces over 10 cm width or girth including preperation of surfaces complete all as specified and as directed. Make :M/s. Asian Paints [Apcolite], M/s. Berger Paints [Luxol], Jenson & Nicholson [Brolac] all are 1st quality.

S & F 20 mm bore Galvanized Steel tubes, medium grade (ISI Marked) for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors / trenches and testing complete all as specified and as directed. Make : Prakash / Tata / Zenith / Jindal

S & F 15 mm bore Galvanized Steel tubes, medium grade (ISI Marked) for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors / trenches and testing complete all as specified and as directed. Make : Prakash / Tata / Zenith / Jindal

S & F 15 mm bore chromium plated bib tap of fancy type, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed. Make : M/s Hindware / Orient / Seiko / Dripless

Excavating over areas not exceeding 1.5m deep and getting out in hard / dense soil complete all as specified and as directed.

M & L for Plain Cement Concrete Type D2, 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed.

S&F Colored designer machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thick, M-40 Grade finished with grey cement and pigment complete all as specified and as directed. Make : Ultra, Eurocon, Duracrete, Mehatab as approved by GE.

M&L for providing PCC type B-1, 1:2:4 (using 20mm graded granite stone aggregates) as in kerbs, chamfered on edges / sides of path etc complete all as specified and as directed.

Excavating over areas and getting out in hard / dense soil for depth exceeding 1.5m and not exceeding 3.0m complete all as specified and as directed.

Removing Excavated spoil to a distance execeeding 250 M but not exceeding 500 M and depositing where directed at a level not exceeding 1.50m above the starting point complete all as specified and as directed.

M&L for RCC M-30 (design mix) as in foundations, including rafts, footings, foundations beams plinth beams, bases for columns, etc, basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L for RCC M-30 (design mix) as in walls, and the like complete all as specified and as directed.

M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and as directed.

M & L for preparation of newly plastered wall surfaces and applying two coats of Cement Based paint over a coat of primer complete all as specified and as directed. Make : Super-Snocem / Durocem / Aquacem

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), complete all as specified and as directed

Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc and removal of rubbish to the out side MD land complete all as specified and as directed.

M & L for Vitrified ceramic tiles (double charged) of approved shade 10 mm thick (Square/ Rectangular) polished, area of each tile exceeding 0.36 Sqm and not exceeding 0.42sqm in floors etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match including screed bed or bedding layer in cement mortar 1:4, 15 mm thick, complete all as specified and as directed. Make : Johnson / Nitco / Asian Granito / Varmora / Orient Bell

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (Square /rectangular) area of each tiles exceeding 0.06 sqm but not exc 0.11 sqm in floors set and jointed in neat cement slurry and pointed in coloured cement to match including screed bed 15 mm thick in cm(1.4) complete all as specified and as directed. Make : Johnson / Kajaria / Orient / Cera / Asian

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (Square /rectangular) area of each tiles exceeding 0.11 sqm but not exc 0.18 sqm in floors set and jointed in neat cement slurry and pointed in coloured cement to match including screed bed 15 mm thick in cm(1.4) complete all as specified and as directed. Make : Johnson / Kajaria / Orient / Cera / Asian

M & L for 25 mm thick, PCC 1:2:4, Type B 1, using (20 mm graded aggregate) as in sub base of flooring complete all as specified and as directed.

M&L for coloured glazed ceramic tiles 350 x 250 x 7 mm / 450 x 350 x 7 mm thick on vetical surfaces such as dados etc over 10 mm thick rendering in CM 1:3 as in backing coat for fixing tiles on vetical surfaces such as dados etc complete all as specified and as directed. Make : Johnson / Kajaria / Orient / Cera / Asian

M & L for machine cut Kota stone slab 20 to 25 mm thick as in flooring laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including screed bed in cement mortar 1:6 20mm thick, complete all as specified and as directed.

M & L for machine cut Kota stone slab 20 to 25 mm thick in in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including backing coat in cement mortar 1:3, 10 mm thick, complete all as specified and as directed.

Taking down chowkats or frames not exceeding 1.5 sqm each with shutters without taking off shutters from frame complete all as specified and as directed.

Taking down chowkats or frames exceeding 1.5 sqm but not exceeding 4sqm each with shutters without taking off shutters from frame complete all as specified and as directed.

S & F 35 mm thick, Factory Made Second Class Hard Wood, Kiln Seasoned and chemically pressure treated plain framed, panelled shutter [any number of panels] with lock rail and panel of 9 mm BWP Commercial ply or 12 mm veneered particle board with commercial face veneers on both faces or 10 mm bison panel complete all as specified and as directed.

S&F factory made second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S & F 300mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixedcomplete all as specified and as directed

S & F 200mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and as directed.

S & F 150 mm long Brass handles, cast type, polished bright fixed complete all as specified and as directed.

S & F 125 mm long Butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed, type B-11 and fixed complete all as specified and as directed.

M&L for preparation of new wood and wooden based surfaces of any description , over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. Make :M/s. Asian Paints [Apcolite], M/s. Berger Paints [Luxol], Jenson & Nicholson [Brolac] all are 1st quality.

S&F Anodised Aluminium frame for doors, windows, ventilators, [ ISI Marked ] fixed partitions etc., with one or more rebates including joining cleat for fixing etc., complete all as specified and as directed. Make : Jindal / Indal / Hindalco

S & F Anodised Aluminium window and ventilator shutters, side hung/siding type without sash bar with powder coating of any colour of minimum 50 micron thick, aluminum section weighing 0.55 Kg/ RM including necessary joining cleats, glazing clips, rubber packing, sliding rollers, anodised aluminum snap beading, screws, anodised aluminum fittings such as peg stays 150 mm long (1 No.), hinges type B-21 100 mm long (2 Nos.), suitable handle (1 No.) if any complete all as specified and as directed. Make: HINDALCO / INDALCO/JINDAL

S&F Anodised aluminium deco grill DG-102 of 5mm dia hexagonal channel, including joining cleat for fixing and necessary fixing arrangements as required, complete all as specified and as directed. Make : Jindal / Indal / Hindalco

S & F PVC solid ventilator frame size 55 X 47mm with wall thickness of 5mm made out of extruded 5mm PVC sheet, mitre cut at two comers and jointed with 2 Nos of 150mm long brackets of 15 x 15mm MS square tube the two vatted profiles are to be reinforced with 19 x 19mm MS squre tube the 50% of bottom portion is fixed with 4mm pin headed glass and balance 50% of top portion is fixed with 4mm thick pin headed glass lowers and cover with 0.36mm dia stainless steel wire mesh at top portion including necessary PVC beading with screws and 3 Nos 12mm dia MS guard, bars fixed in ventilator frame including two coats of synthetic enamel paint over a coat of red oxide primer to MS guard bars etc complete all as specified and as directed. Make: SINTEX / NANDI / Rajshri plastiwood

S & F 5.5 mm thick Sheet glass, ordinary quality and glazing with oil putty fixed to aluminium windows in squares exceeding 0.5 Sq. M in each pane complete all as specified and as directed. Make: Saint Gobain / Modi Guard / Asahi

M & L for prepolished Granite (of any type) work 20 mm thick machine cut (table rubbed and polished) in floorings, steps, jambs, pillars, window-cills, cooking platforms, skirting / dado and the like including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite laid over and including backing coat in cement mortar 1:4, 10 mm thick and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of stone complete all as specified and as directed.

S&F Solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and as directed.

S&F in 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and as directed. Note for Item No. 102 & 103 : Make : Sintex / Nandi / Rajshri Plasti Wood.

M&L for point wiring with two runs of single core 1.5 Sq.mm (Nominal area) PVC insulated unsheathed [ISI marked] FRLS grade stranded copper conductor cable 1100 Volts grade drawn through and including concealed PVC rigid conduit non-metallic 20 mm bore Medium grade including 1.5 Sq.mm PVC insulated unsheathed FRLS grade copper cable solid conductor as earth lead including MS consealed/ semi concealed terminal boxes made of 2mm thick MS sheet covered with 3mm thick laminated sheet complete all as directed for One light / fan / Bell point controlled by one way switch

All as per item No. 104 above but with 2.5 Sqmm FRLS copper cable for one 15 Amps power point including 2.5 Sq mm FRLS copper conductor cable as earth continuity conductor and connecting it to earth dolly complete all as specified and as directed.

All as per item No. 104 above but with 4.0 Sqmm FRLS copper cable for one geyser/AC/ Water cooler point including 4.00 Sq mm FRLS copper conductor cable for earth continuity conductor cable as earth continuity conductor and connecting it to earth dolly complete all as specified and as directed. Note for item Nos 104, 105 & 106 : Make of Cable : Finolex, Polycab, Plaza, Gloster, Harsh all are ISI marked and FRLS cables Make of Conduit : Avon Plast,Precision, Finolex all are ISI marked.

S & F Switch socket combination 3 pin, 5A /15 A flush type complete all as specified and as directed. Make : Anchor / Bajaj / Cona

S&F ceiling rose surface bakelite 65 X 50mm two to three terminals complete all as specified and as directed. Make : Cona / Anchor / Legrand

S & F switch piano flush type single pole 5 Amps oneway AC 230V, 50HZ supply complete all as specified and as directed. Make : Anchor / Cona / Bajaj

S&F Concealed Sheet metal enclouser single pole and neutral enclosure with two pin and earth plug and socket complete with one single pole MCB 20 amps capacity complete all as specified and as directed. Make : INDO ASIAN / STANDARD / HAVELLS

S & F Ceiling fan 1200mm sweep suitable for single Phase 230 Volts with all accessories, stepped by electronic regulator and making suitable hook for fixing of ceiling fan and making good the existing surface complete all as directed. Make: Bajaj / Crompton Greaves / Usha

S&F Distribution Board, SPN 8 Way ,Double door 240V with 200Amps rated bus bar, True IP 43 protection with test reports complete all as specified and as directed. Make : Indo Asian cat part No. 811807[Optipro] / Standard / Havells

S & F MCB SPN 63 Amps 240 Volts C curve, complete all as specified and as directed. Make: Indo Asian STANDARD / HAVELLS/Schneider

S & F MCB SP 6 to 32 Amps, 240 Volts, C curve, complete all as specified and as directed. Make: Indo Asian Cat part No. 811122 to 811129 / L&T / C&S / Schneider / Legrand

S & F recessed mount LED down lighter 2' x 2' , 36 W ultra modern designed architectural LED Luminaire which provide soft-light and glaire free symmetrical illumination suitable for Armstrong / grid ceiling complete all as specified and as directed. Make: Crampton Cat No. LCPL-36-CDL/TL (2x2) or its equivalent in Bajaj / Philips / Havells / HPL

Supply and install hi wall split units indoor / out door complete with cordless remote control unit and with in built air ioniser and plasma filter for better indoor air quality with Eco Friendly R 410 A Refrigent gas minimum 5 star rating and EER 3.2 of capaccity 2.0 TR complete all as specified and as directed. Make : Carrier / Blue Star / Hitachi

Supply and Fix wall mounted voltage stablizer for automatic operation single phase naturally air cooled indoor type and design for input variation between 170V to 250V with accuracy + 2.5% and of 5 KVA capacity complete all as specified and as directed. Make : V Guard / Servo / Kee line

M & L for Sub main wiring with 2 runs of 6 Sqmm PVC insulated FRLS Copper conductor cable including PVC conduit of 20mm dia along with one run of 6.0 Sq.mm FRLS copper cable for earth continuity conductor as earth lead and connecting to common earth dolly complete all as specified and as directed. Note: Two runs 6 Sq.mm. cable, one run of 6 Sq.mm cable and one run of PVC conduit will be measured as one unit. MAKE :(i) Make of Cable : Finolex/Polycab/Plaza/Gloster/Harsh all are ISI marked and FRLS cables (ii) PVC CONDUIT : AVON PLAST, PRECISON, FINOLEX [ALL ARE ISI MARKED]

S&F PRV (Pressure reduction valve) of Brass including making new joints or connection for union and nipple to the existing 20 mm pipes alongwith errection and dismantling double steel scaffolding with platform at every PRV (Pressure reducing valve) joint upto the height of 10th storey of bldg alongwith setting the required pressure of water at every PRV joint including cost of union and specials as required at site complete all as specified and directed. Make: Kirloskar / L & T / Upadhyay / Leader / Zolotto

K SATYANARAYANA ENTERPRISES

Sri Vayuputra Constructions

K K INFRA