SPECIAL REPAIR TO BUILDING NO 219 AND 220 (OR MD ACCN) INCLUDING CERTAIN MINOR AND REVENUE WORK AT NAHAN UNDER GE CHANDIGARH

Amount

Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, including cutting of trees, shrubs or any type of vegitation upto and including roots complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces , finished even and fair without using extra cement on walls in cement mortar1:4, (using WPC) complete all as specified and as directed. Note:- WPC shall be measured and paid seprately.

M&L for rendering 15 mm thick on brick work or concrete surfaces, finished even and smooth without using extra cement on walls in cement mortar 1:6, in patches complete all as specified and as directed.

M&L for rendering 10 mm thick cement plaster in CM (1:3) on ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing & finishing walls with acrylic smooth exterior paint of required shade(New work)(Two or more coats applied @1.67ltr/10 Sqm over and including priming coat of exterior primer applied @2.20 kg/Sqm complete all as specified and as directed.

M&L for Two coats of acrylic distemper/ distemper oil emulsion (OBD) on new plastered wall surfaces of any description over 2mm thick wall care putty complete all as specified including preperation of surfaces complete all as specified and as directed.

M&L for preparation and applying three coats of white wash on new surfaces of ceiling complete all as specified and as directed.

M&L for preparation and applying three coat of white wash on old ceiling old surfaces complete all as specified and as directed.

M&L for preparing & finishing on old walls with acrylic smooth exterior paint of required shade(New work)(Two or more coats applied @1.67ltr/10 Sqm over and including priming coat of exterior primer applied @2.20 kg/Sqm complete all as specified and as directed.

M&L for two coats of acrylic distemper/ distemper oil emulsion (OBD) on old wall surfaces including complete removal of existing treatment and all necessary preparation with and incl priming plastered surface over 2mm thick wal care putty, complete all as specified.

M&L for preparation of new steel surfaces of any description, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

M&L for preparation and applying two coats of synthetic enamel paint over a coat of pink primer on new wooden surface of any description ,not otherwise described complete all as specified and directed.

M&L for preparation and applying one coat of synthetic enamel paint over old painted steel & iron surfaces of any description, not otherwise described, over 10 cm in width or girth, complete all as specified and as directed.

M&L for preparation and applying one coat of synthetic enamel paint over steel & iron surfaces of any description, not exceeding 10 cm in width or girth, unconnected with other painting or when painted in different tint complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and directed.

S & F in repair vitreous China wash basin, (white) Flat back, size 550x400 mm including cast iron brackets, PTMT waste coupling and PVC waste pipe complete all as specified and directed.

S&F in repair vitreous China Squatting pan, 'orrisa pattern, size 580x440 mm (white) with integral foot rests with and including 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for 15 mm bore iron pipe and fixed complete all as specified and directed.

S&F in repair (centre hole mixer), cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for 15 mm bore iron pipe and fixed complete all as specified and directed.

S&F in repair 15mm dia bib taps CP brass,fancy type,long body, screwed down, screwed for iron pipe complete all as specified and directed.

S&F in repair 15mm dia Angle cock chromium plated brass fancy type, screwed down , high pressure, scrwed both ends for iron pipe complete all as specified and directed.

S&F in repair cast iron Nahani trap(dia of outlet 75 mm), with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S & F Continuous (piano) hinges 30 mm wide , mild steel, bright finish or electro galvanised complete all as specified and directed.

S&F in repair 100 mm Hasp and staple, safety type, aluminium anodised hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S & F 4mm sheet glass ordinary quality and glazing with oil putty in squares n exc 0.5 sqm in each pane complete all as specified and directed.

S & F 4mm Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 in each pane complete all as specified and directed.

S & F in repair 18-19mm thick particle board, interior grade pre-laminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber/aluminium frame work complete.

M&L machine cut Kota stone slab 20-25 mm as in floors etc laid over cement screed bed jointed with grey cement slurry mixed with pigment to match the shade the slab including rubbing and polishing complete with and incl 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L kota slab 20-25 mm thick in risers of steps, skirting dado and pillar laid over cement screed bed jointed with grey cement slurry mixed with pigment to match the shade the slab including rubbing and polishing complete with and incl backing coat 10mm thick in CM 1:4 complete all as specified and directed.

S&F in repairs factory made Box type steel window steel frame 80mmx60mm(peripheral) and 80mmx75mm(intermediate memebrs)made out out of cold rolled 1.25mm thick sheet having steel window/ventilator shutter of MS tabular section of size 50mmx20mmx1.10mm thick fixed with box type hollow tabular section beading for glazed and wire shutter handle of 100mm size made out of Z section 2 Nos MS stove enameled black bolt of size 120mm 02 Nos, 150mm mild steel hook and eyes, complete all as per drawing No TD-277R sheet 1/4 to 4/4 of HQ CE Chd zone. Note:- the cost of a shop coat of primer shall be admissible on this account.

All as per item No 30 above but without glazing bar as per drawing No TD-276R sheet 1/4 to 4/4 of HQ CE Chd zone.

S & F mild steel ventilator with top hung or fixed half glass and half wire mesh portion and including if required projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded. (The glass and wire mesh will be measured and paid for seperately)

S & F Galvanised mild steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed stainless steel wire staples complete all as specified and directed.

Cutting chases in stone wall, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

M&L 15mm GI tubes medium grade with all fittings & fixed complete to walls or ceilings or laid in floors complete all as specified and directed.

M&L 20mm dia GI tubes medium grade with all fittings & fixed complete to walls or ceilings or laid in floors complete all as specified and directed.

Taking down steel water tubing 15mm to 20 mm with all fittings from walls, ceiling and floors, complete all as specified and directed.

S&F in repair 20-25mm mm dia curtain rod made of aluminium Pipe with decorative lining coating,including brackets and decorative balls / caps at both ends of rod with comp fittings complete all as specified and directed.

S&F ball catchers for cupboard and kitchen cabinets both male & female part (making each set) complete all as specified and directed.

S&F in repair 15mm dia Stop valves, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

M&L for Framed work such as grills,gratings,etc..with ends of bars shouldered and/or riveted,or forged into spikes, framed guard bar, for tank staging , conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F in repairs Brass chromium plated shower rose 125mm size,with complete fitting complete all as specified and directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mmcomplete all as specified and directed.

Dismantling wall and ceiling boards (fibre pulp, insulation, etc) or insulation boards/slabs/blankets any thickness including cover fillets complete all as specified and directed.

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre incl fixing hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long for false ceiling with and incl 12mm thick perforated particle boards or tiles with 02 coats of oil bound distemper on boards for insulation and accoustic purposes, 60cm x 60cm in size all as specified for size of grid 605 x 605mm complete all as specified and directed.

Dismantiling timber scantling in fillets, rail, posts, rafter, purlins, etc under 40Sq.cm in section complete all as specified and directed.

S&F 1000 Ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified.

Dismantling water tanks capacity 1000 ltr complete all as specified and directed.

S & F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S & F in repair Brass chromium plated Tubler towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S & F in repairs 15mm dia bore pipe Ball brass valves high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

Taking down CI soil waste or vent pipe 100mm bore including all fittings like trapes,bends,junctions etc from any situation complete all as per specified and as directed.

Taking down CI soil waste or vent pipe 75mm bore including all fittings like trapes,bends,junctions etc from any situation complete all as per specified and as directed.

S&F 110MM PVC SWR Pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 75 MM PVC SWR Pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors.

S&F in repair 110MM PVC SWR Bends any radius complete all as specified and directed.

S&F in repair 75 MM PVC SWR Bends any radius complete all as specified and directed.

S&F in repair 75MM PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F Door strip (snake guard strip) complete all as specified and directed.

S&F 5.00mm thick glass corner shelf set (one piece) having stainless steel perimeter border all as specified and as directed.

M&L Cement concrete type B -1, 1:2:4 type B-I (20mm graded stone aggregate) 25 mm thick, complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) with old size bricks disignation 10 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L ceramic coloured tiles 8-9mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L coloured vitrified tiles (scratch and strain resistant tiles) 10mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and include 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises

M&L Glazed ceramic coloured,,tiles 450x350x6-7mm thick in vertical surfaces such as skirting,dados and risers to steps over and including 10mm thick in CM (1:4) complete all as specified and directed.

M&L Black Granite stone 18-20 mm thick as in kitchen platform work (table rubbed and polished) and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admix ture of pigment to match with shade of granite including 15 mm thick screed in CM 1:3 complete all as specified and directed.

Dismanntling of plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering complete all as specified and directed.

S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws complete all as specified and as directed.

S&F prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges, valleys, gutters etc. fixed with self tapping screws complete all as specified and as directed.

S&F Fe 410-w(Gde E 250)quality B rolled mild steel roof trusses (framed) trussed, purlins, crane gantries, rails and framing (beam, tee, angle, channel or flat sections) including distance pieaces cleats etc complete all as specified and directed.

Taking down Chowkhats or frames without taking off shutters from the frame not exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkats or frames without taking off shutters exc 1.50Sqm but n exc 4.00Sqm complete all as specified and directed.

S&F factory made solid PVC Door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening as per specified.

S&F factory made solid panel PVC Door shutter 30mm thick (stiles)consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain cover PVC 'C' channel having PVC strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rails on either side & as gap insert for top rail & bottom rails, panelling of plain colour PVC sheet to be the fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing in the frame at site as per specification and drawing.

S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F 100mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 125mm size, Stainless Steel, D type with back plate, handle and fixed with screws complete all as specified.

S&F 250mm long mild steel, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including bolts and nuts complete all as specified.

Supply and fix 30mm thick flush shutters, solid core construction, with block board core and plywood face one face is covered with decorative face veneer with lippling/frame to match including cupboard partitions/shelves etc complete all as specified and directed.

Supply and fix 2nd class hard wood factory made glazed and skeleton shutters 30mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in clause 8.24 (a) of SSR Part-I; supplied and fitted to chowkhats complete all as specified and directed.

M&L stone walling built in CM 1:6 of random rubble uncoursed, well bonded, solidly hearted built in retaining walls, abutment and sililar work complete all as specified and directed..

M&L stone walling built in CM 1:6 of random rubble uncoursed, well bonded, solidly hearted built in retaining walls, abutment and sililar work but except(old stone received) complete all as specified and directed.

Flush pointing to random rubble, uncoursed or brought up to coursed CM 1:4 complete all as specified and directed.

Demolition of brickwork or stone/boulder masonary, built in lime mortar including quoins arches, pillers etc, but excluding ashlar facings, dressed stone work and precast concrete article built in cement mortar or cement lime mortar complete all as specified and directed.

M&L for 75 mm thick cement concrete type C-2, 1:3:6 using 40mm graded stone aggregate as in plinth protection, finishing the cement concrete surface even and smooth without using extra cement complete all as specified and as directed.

Forming contraction (dummy) joints 25 mm deep x 10mm wide, filled with sealing compound Grade A complete all as specified and as directed.

M&L providing for PCC 1:3:6 Type C-1 using 20mm aggrgate as in coping, apex stone, complete all as specified and directed.

M&L Cement concrete in surface channels and drains in cement concrete 1:3:6 type C2 (20 mm graded stone aggregate) complete all as specified and directed.

Extra for forming fair finished drain or channel 60 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed.

Demolitioin of cement conc in ground floors and pavings n.exc 15cms thickness (below or above GL).

Demolitioin of cement conc(reinforced) in ground floors and pavings n.exc 15cms thickness (below or above GL).

S & F Pressed steel frames 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. including making good to existing surface jamb/floor complete in all respect including demolished flooring /tiles making jambs, giving existing type of surface finish etc so as to mach the existing surface, as specified

S & F Pressed steel frames 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. including making good to existing surface jamb/floor complete in all respect including demolished flooring /tiles making jambs, giving existing type of surface finish etc so as to mach the existing surface, as specified

S&F in repair kitchen Plate Rack stainless steel having size 600mm x900mm x250mm (approx) incl fixing to walls with fasteing screws, rubber/PVC beading /capping complete to sustain utensils weight upto 8-10 Kg complete all as specified and directed.

S&F in repairs waste pipe 32mm dia flexible for Sink all as specified and as directed.

Demolition and breaking up drain pipe 100mm bore salt glazed stone ware/AC/PVC pipe complete all as specified.

M&L Cement concrete (1:3:6) type C2 using 40mm graded crushed stone aggregate as in bed to drain pipes 100mm bore including packing under and haunching against the sides of pipes after laying and testing complete all as specified

M&L 100mm bore (internal dia) salt glazed stone ware pipes grade A laid in trenches on concrete bed to required slope jointed complete all as specified.

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre deep and n exc 10 sqm on plan and getting out in soft and loose soil complete all as specified.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm complete all as specified.

Removal of excavated soil to a distance not exc 50 metre and depositing where directed at a level not exc 1.5 metre above the starting point complete all as specified.

Dismantling mild steel work of any description not otherwise provided for in any location and any position complete all as specified and directed.

M&L RCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in , cover slab , slab for septic tank , shelves supported on walls, etc

Formwork to soffits of suspended slabs such as roof slabs, floor slab, landings and similar work not exceeding 200mm thick, horizontal or sloping finished rough complete.

TMT bars 10mm dia and over cut to length , bent to shape required including , cranking hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips complete.

M&L for Rough excavation not exceeding 1.5 m deep in Hard/Dense soil and getting out, complete all as specified and as directed By Engr-In-Charge.

M&L for removing surplus excavated material exc 1.50m but not exc 5.00km and depositing where directed.

Sand filling under floors or in foundations including watering and consolidation

Material & labour for 60mm thick non skid pre polished coloured interlocking paver block made with electro vibro technology with rubber/ PVC moulded of not less than compresive strength 30 Kg/Cm and shape and size confirming to IS 15658-2006 of M-35 Grade with grey cement and pigment complete all as specified and directed by Engineer in Charge.

Material & labour for providing cement concrete Type B1 1:2:4 (20mm graded crushed stone aggregate) kerbs or mut stops, rounded or chamfered on edges etc complete including necessary form work complete all as specified and directed.

M&L for Hard core of gauge exc. 63mm but not exc 100mm,deposited,spread and levelled in layers not exc. 15 cm thick, watered and rammed/rolled to a true surface complete all as specified.

M & L 75 mm thick Cement concrete type D2,1:4:8 (40mm graded stone aggregate) as in sub base,path,floor, hardstanding complete as as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including ,fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. all as specified and directed.

Taking down MCB DB /Old Meter box of any size and disposal under schedule of credit and making good disturbed surfaces all as specified and directed.

Taking down old unserviceable light fittings any type and removal from site and making good disturbed surfaces of walls, ceiling etc complete all as specified and directed by Engineer-in-Charge to match with existing surface all as directed.

M&L for point wiring using approved colour coding as per IS ( for Phase and neutral) with copper conductor 1.5 sqmm ( Cross sectional area) single core multistranded FRLS ,PVC insulated and unsheathed cable 1100 volts grade,conforming to IS drawn and including PVC concealed coduit with fittings ISI marked ,terminated in modular switch boxes incl 1.5 sqmm (cross sectional area ) single core ,multistranded ,FRLS PVC insulated and sheathed cable as earth continuity conductor connected to earth dolly for one light point control by one way switch complete all as specified and directed.Note: 1.colour code of wiring should be ( for phase ,red,neutral ,black & earth wire green) 2.Modular switch sockets fan regulators shall be measured and paid separately under respective items deemed to be included in the quoted rates.

- Ditto - all as per item No - 119 above but controlled by two way switch.

- Ditto - all as per item No - 119 above but one call bell point controlled by one bell push point.

- Ditto - all as per item No - 119 above but for one ceiling fan/exhaust fan point.

- Ditto - all as per item No - 119 above but for one 3 pin 5 amp socket on same board all as directed.

- Ditto - all as per item No - 119 above but for one 3 pin 5 amp socket on indipendant board all as directed.

- Ditto - as per item No 119 here in before but with 4 sqmm copper conductor for 15 amp socket with 4 sqmm earth continuity conductor

S&F of Modular snap switch SP one way 5/6 Amps suitable for 1 Module complete all as specified and directed.

S&F of Modular snap switch SP two way 5/6 Amps suitable for 1 Module complete all as specified and directed.

S&F of Modular Bell push ,SP 5/6 A suitable for 1 Module complete all as specified and directed.

S&F of Modular socket 5 pin 5/6 Amps suitable for 2 Module complete all as specified and directed.

S&F of Modular snap switch SP one way 15/16 Amps suitable for 1 Module complete all as specified and directed.

S&F of Modular socket 5/6 pin 15/16 Amps suitable for 2 Module complete all as specified and directed.

S & F of Modular Fan step Regulator electronic, 120 watts,2 Module complete all as specified and directed.

Supply and fixing of Modular Indicator lamp, 2 Module size complete all as directed.

S&F of Modular blanking plate suitable for 1 Module complete all as specified and directed.

S&F of Modular white cover plate incl Modular base frame & powder coated Modular sheet metal concealed box for 12/8 module complete all as specified and directed.

All as per Item No-135 above but 6 module complete all as specified and directed.

All as per Item No-135 above but 3/4 module complete all as specified and directed.

All as per Item No-135 above but 2 module complete all as specified and directed.

S&F of ceiling rose surface backalite 65mm x 50 mm, two to three terminals complete all as specified and directed.

Supply and fixing of lamp holder insulated body with back plate suitable for any type of fitting incl one No of LED Bulb 15-18 Watts Base B-22 retrofit type all as specified and directed.

S&F of Electric bell, AC, 230volts, single phase, Ding Dong type complete all as specified and directed.

Supply and fixing of Indoor Decorative LED box type suitable for fixing ceiling/wall with aluminium base directly retro fit LED tube Light , 22 watt, , Color: Cool day light 4 ft white Operating Voltage: 140-270 volts complete with all accessories internally pre wired and including up with three core PVC copper flexible cable of size 23/0.0076 from ceiling rose to connector block complete all as specified and directed LED batten & LED tube rod shall be of same brand.

Supply and fixing of LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. complete all as specified and directed. Make :Halonix Model No:HLBH-15-10-CW-INV or equivalent in CG/Philips/Havell's.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC,decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing of 25 watt LED batten with opal diffuser ,IP20, battery backup upto 4 hrs.Fitting should have inbuilt 2 No's of Li-on battery of 2600mA each.Housing of fixture should be of extruded aluminium Efficacy of fixture >100LPW,P>F>0.9,THD<30% complete all as specified and directed.Make: Halonix Model No: HLB-08-25-CW-INV or Equivalent in Crompton Greaves,Bajaj,Philips,Havell's.

Supply and fixing of 60 watt LED inverter RTC(street light with inbuilt RTC (Real Time clock) for Auto on/Auto Off. Housing made of Pressure die cast aluminium ,top maintainable and with clear heat resistant toughned glass , have secondary lens for better optics, should have LM80 certified LED of CREE,NICHIA, OSRAM,SEOUL make only with constant current RTC enabled electronic driver with 5KV SPD,IP66. Street light shall have inbuilt Li-on battery of 5200mAH and shall have>1.5 hrs battery backup at inverter load in case of power failure,Efficacy > 100LPW,CRI>70,THD<10%,PF>0.95,cut off voltage at 300 Volt + 10% and suitable for 50mm mounting GI Pipe complete all as specified and directed.Make: Halonix Model No: HLSLD-ML04-60-CWL-INV-RTC or Equivalent in Crompton Greaves,Bajaj,Philips,Havell's..

Supply and fixing of security light fitting bracket made up of 25/32 mm dia medium grade pipe of length 0.9 mtr with bending in shape by hot or cold method with 2 nos 50x4 mm MS flate clamps with nut bolts and washer etc all as directed

Supply and fixing of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, TPN 04 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc flushed on the existing wall , to match with existing surface and making all necessary connections complete all as directed.Make : L&T / Legrand Lexic Hager/Havell's/Indo Asian.

All as per item No: 148 but MCB DB SPN 8 way complete all as specified and directed.

S & F of isolator TPN 4 pole 63 amp 415 Volt complete all as specified and directed.

S & F of isolator DP 2 pole 63 amp 230 Volt complete all as specified and directed.

S & F of isolator SP, 6-40 Amps, 230 Volts complete all as specified and directed.

M&L of blanking plate suitable for MCB DB's SPN/TPN complete all as specified and directed.

S & F in replacement of Sub main wiring with PVC insulated, FRLS cable 2 single core 6 Sq mm 1100 V grade with stranded copper conductor on and incl PVC rigid non metalic conduit (ISI marked) in concealed incl all specials like joint, elbow , Tee ,junction , bend etc and provision of PVC insulated copper conductor single core 6 sq mm for earth continuity conductor including taking out UNSV sub main wirng alongwith conduit and accessories complete all as directed.Note: Two run of 6 sqmm and one run of 6 sqmm earth continuity conductor shall be measured as one unit.

Earthing complete with Galvanised steel earth plate electrode of size 60cmx 60cm x 6mm thick electrode buried directly in ground (earth pit not less than 2.25 meters deep below the normal ground level) with top edge of the plate not less than 1.5 m below normal Ground Level connected to GI earth wire 4 mm dia by means of bolts, nuts, check nuts and washers and earth lead protected by 15mm dia GI pipe medium grade connected to main distribution board/ earthing test point all as shown on electrical plate No-03 of SSR Part-1 and all as specified including testing on completion.Note: The unit rate shall also include for excavation, earth work in hard/dense soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bars @ 150mm c/c both ways , GI funnel with watering pipe 20 mm dia, wire mesh, salt and charcoal, protection pipe for earth lead upto 7.50m long complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified in SSR part-II earth lead wire and protection pipe beyond 7.5m shall be measured and paid separately.

M & L for Brick protection for LT cable with sub class "B" bricks laid dry and flat abutting each other with gaps between adjacent bricks not exceeding 10mm with width equal to length complete all as specified and directed by Engr-in-Charge

M & L for sand cushioning to PVC under ground cable with screened and washed sand and punning to provide a required cover.

Supply and laying of GI tubing, light grade, 50 mm bore dia as cable protection fixed on walls/poles/laid in trenches complete including dismantling corroded GI pipe all as specified and as directed.

Supply, laying , jointing ,testing and commisioning LT underground cable 1100 volts grade XLPE insulated and steel strip or wire armoured heavy duty with multistranded aluminium conductor 16 Sqm 4 core size including taking out unserviceable complete all as specified and directed. Note:- (i) Excavation and earth work cable protection and sand cushioning shall be measured and paid seperately .

Taking down and re fixing the existing water geyser/ Ceiling fan/exhaust fan any type and any size after necessary servicing/greasing complete incl painting all as specified and directed by Engr-in-Charge to match with existing surface complete all as specified and directed.

Material and labour for road / path way any type (Concrete) cutting , including excavation, returning filling in, spreading, leveling, well ramming in layers, soiling with broken boulders/ stones, WBM 7.5 cm thick coarse aggregate received from dismantling the existing road, premix, carpeting 25 mm thick using ready mix patch mate material, rolled and compacted for road patch repair work, complete all as directed.

M&L in replacement of fabrication of sheet metal enclouser to accommodate 04 Nos electric meters of size 800 mm x 500 mm x 150 mm deep and 1.6 mm thick MS sheet, powder coated, bakelite sheet with side hung shutter including provision of locking arrangement and niche covered with 4 mm thick plain glass , including locking arrangement & open Wiring coverd with Flexible Pvc Pipe of suitable size complete all as specified and as directed.

Supply and fixing of Exhaust fan 300 mm sweep heavy duty complete with self closing MS louvers, mounted in suitable opening arrangement and suitable for operation on 230/240 Volts single phase, 50 Hz,1400 RPM , AC supply with and including two core PVC insulated, PVC sheathed copper conductor flexible cable 24/ 0.2 mm and making all necessary connection and fixed by using 4 Nos 100 mm long 10 mm dia bolts, nuts and washers and grouted in wall in CM 1:3 (including opening of wall etc) completed all as directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 300m and making all electric connections complete all as specified and directed.

Supply and fixing of Water heater (Geyser) Storage type , vertical type 5 star rating electric 230 volts AC,50 Hz capacity 25 ltrs with 15 Amps plug top fixed on wall by means of anchor fastners-04 Nos ,12mm dia and 150mm long grouted into wall and making good the disturbed surfaces with existing finishes complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and ccessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) ® with provision of cable PVC insulated and sheathed FRLS grade 3 core 1.0 sqmm copper conductor flexible wire 1100 volts grade from porcelain connector /ceiling rose to ceiling fan complete all as specified and directed.

Supplying and fixing smart single phase two wire dual source prepaid energy meters BIS 15884 marked in existing meter board / florr panels with pre payment capacity touch keypad based digital having current range 10-60 Amp 240 Volt accuracy class 1.0 alongwith parallel home display split unit with inbuilt load control switch containing provision for TOD and RTC, inbuilt feature to sense the DG mode through PLSI, dual source registration wrt grid as well as DG supply and dynamic load allocation facility from grid and DG, capable to define for tariff slabs, happy hours and holiday definition making all electric connections complete all as specified and directed.Make: Securemeter/L&T/Schneider Elect.Note: The UNSV old one Item Srl No 163 to 167 is MES property and will be handed over to MES Store Yard .

Supply and Fixing 10 to 15 Watt LED decorative wall mounting type light fitting incl 01 No, 7 – 15 watt LED retrofit bulb complete with all accessories internally pre wired and including up with three core PVC copper flexible cable of size 23/0.0076 from ceiling rose to connector block complete all as specified and directed.

Taking out existing unserviceable old CI/MS pipe line of 300 mm bore with all fitting and Supply, laying, jointing and testing of MS ERW pipe line medium grade 300 mm dia (ISI marked) both end flanged with and including MS flange 20 to 25 mm thick consisiting 12 holes with 12 Nos bolts and nuts, washer and compressed fiber board 3 mm thick rubber sheet and all MS fitings including sufficient no's of holes on the pipe line (perforated pipe) as per requirement for filtration purpose complete all as specified and as directed by Engr-in-Charge. Make :- Jindal/ Tata/ Electro steel. Note:- (i) Excavation and earth work shall be measured and paid seperately under respective item of this schedule. (ii) Fittings for repair such as elbow,union, tee, nipple,flange,Gasket ,nuts,bolt etc included in this quoted rate (iii) Welding machine,welding rods,DG Set,JCB,lifting crane and manpower required for this job is included in quoted rate (iv) The repair work carried out all as per direction of Engr-In- Charge .(v) The work will be carried out in river bed/inside of the river as per requirement.

Taking out existing unserviceable old GI pipe line of 50 mm bore with all fitting Supply, laying, connecting & testing of 50 mm bore steel water tubing galvanized medium grade, with all fittings & fixtures (ISI marked) laid in trenches or fixed along walls or in any position complete all as specified and as directed . Make :- Jindal/Tata/ Electro steel.

Taking out unserviceable old gun metal gate or globe valves of 50 mm bore with all fitting and S & F gun metal gate or globe valves heavy duty yoke type, full way openig with iron wheel head screwed with both end of GI tubing 50 mm bore ISI marked all as specified and directed.

Taking out unserviceable old NRV of 50 mm bore with all fitting and S & F as in repair cast steel body reflux valve (non return butterfly valve) with by pass arrangement having dia 50 mm heavy duty class 300 all as specified in repair.

Excavation in trenches in hard dense soil n. exc 1.50 mtr wide and n.exc 1.50 mtr in depth for foundation for laying of pipes complete all as specified and as directed

Add to item no 173 above for each additional 1.5m or part thereof in depth beyond the first 1.5 m complete all as directed.

Material and Labour for Broken stone or boulders Hand packing (more than 150mm) at back of walls over arches or in river etc. and raising (or lowering) to the required level complete all as specified and directed.

Material and Labour for Broken stone or boulders Loose filling with aggregates of gauge 80 to 150 mm in soakage pits, soakage well or bore well in river for filtration purpose complete all as specified and directed.

Material and Labour for Broken stone or boulders Loose filling with aggregates of gauge 40 to 80 mm in soakage pits, soakage well or bore well in river for filtration purpose complete all as specified and directed.

Matrial and Labour Graded coarse aggregate 20mm size complete all as directed

Matrial and Labour Graded coarse aggregate 12.5mm size complete all as directed

Supply, installing , testing of 5HP Borewell Submersible pump set 3.7 KW, electric driven 415 V, TP suitable for 250/300mm borewell, outlet dia 50mm,discharge capacity 475-120 LPM, radial flow,head range: 17-60m complete all as specified and directed. Make: ComptonTexmo / CG/Kirloskar/Havell's.

Supply,installing,commissioning of 5 HP three phase DOL submersible pump panel , size 220mmx140mmx120mm, pickup voltage minimum 70% of coil rating,operational voltage: 280-440volt,ambient temprature -25C to +55C,relay: Make-1 4P,current rating : 9-14Amps complete all as sppecified and directed.

Material and labour for 4 sqmm ,3 core coppper multistaranded flat cable suitable for submersible pump 5HP complete all as specified and directed.

S & F Rigid non-metallic PVC conduit exclusive 2 mm thick 25 mm dia of boxes junction/terminal) but inclusive of all tees, bends, elbows, educers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. etc complete all as specified and directed.

M & L 100 mm thick Cement concrete type C-2, 1:3:6(40mm graded stone aggregate) as in sub base,path,floor, hardstanding complete as as specified and directed.

Material & labour for reinforced cement concrete M-20 (design mix) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete. complete all as specified and directed. Note : Reinforced if any used in subject item shall be measured and paid separately.

Material & labour for reinforced cement concrete M-20 (design mix) as in columns, pillars, piers, posts and struts complete all as specified and directed. Note : Reinforced if any used in subject item shall be measured and paid separately.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

Material & labour for mild steel high yield strength TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers, binders etc cut to length bent to shape required, including cranking, hooking ends, bending and binding with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L Cement concrete (1:3:6) type C2 using 40mm graded crushed stone aggregate as in bed to drain pipes 100mm bore including packing under and haunching against the sides of pipes after laying and testing complete all as specified and directed.

Two coats of cement base paint on old wall and all necessary preparation and wetting and curing, complete all as specified and as directed.

M/S SHANTI SARUP DINESH CHAND