SPL REPAIR TO BLDG NO T 161 TO T 163 AND T 168 PROVN OF EMBANKMENT WORK BY MUD IN SHORT RANGE OF WT SECTION AND PROVN OF PCC FLOOR AND SEATING PLATEFORM IN SQUAD POST OF WT SEC AT IMA DEHRADUN

Amount

Dismantling of AC corrugated or semi corrugated, sheet in roof coverings, complete all as specified.

Dismantling timber scantlings 40 Sqcm and over in any section, in any position, Unframed work, complete all as specified.

M & L for second class hard wood as in scantling, trusses, clean sawn, complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws complete all as specified.

S&F pre-painted galvatume aluminium zinc coating GI based Plain steeel sheet 0.50mm thick an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified.

M & L for 0.80 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with Class-VIII, complete all as specified.

M &L for Non asbestos 4 mm thick fibre cement building boards fixed in ceiling or laid/ inserted to timber/GI/Aluminium framework with screws fixed in repairs complete all as specified.

M & L for Anodised aluminium snap grid frame work for false ceiling all as specified .

M&L for Hangers 6 mm dia G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5mm dia. 40 mm long complete all as specified.

S&F mild steel as in hold fast and like including bolting, cutting drilling complete all as specified.

Taking down cement plaster on brick or stone walling built in cement mortar including raking out joints hacking for key scrubbing down with water etc complete as specified.

M & L for rendering on walls 15 mm thick in cement mortar(1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using using extra cement all as specified and directed.

M& L for Rendering 15 mm thick on fair face of brickwork or concrete surface in cement mortar (1:4) with using WPC and finishing the surface even smoothg without using extra cement. Note:- Cost of WPC shall be included in quoted unit rate of this item.

M & L for complete removal of existing treatment on old decorated surfaces (plastered/un-plastered) on walls including cornices on plastered surfaces,and applying wall putty complete, all as specified and directed.

Preparation of new surfaces and applying two coat of cement paint over a coat of primer on walls etc complete all as specified and directed.

Preparation of new surface of walls and applying two of oil bond distemper (OBD) over a coat of primer complete all as specified and directed.

Preparation of old surfaces of walls and applying one coat of oil bond distemper (OBD), complete all as specified and directed.

Preparation of old surfaces of walls and applying one coat of cement base paint complete all as specified and directed.

M&L preparation of new or previously untreated steel surface of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified.

Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with Creosote complete all as specified.

Preparation old painted wooden surfaces of any description over 10 cm width or girth and applying One coat of synthetic enemelled paint complete all as specified and directed.

Preparation new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enemelled paint over one a coat of pink primer complete all as specified and directed.

Demolition of brick work/ stone masonay built in cement mortar including all quoins jamb pillars etc.

M & L for brick work with sub class 'B' bricks in cement mortar 1:6 straight or curved on plan exc. 6.00 m mean radius with old size bricks complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as directed.

Demolition of cement concrete in ground floor and pavings n.exc. 15 Cm thick below or above ground level. (un renforced).

M&L for 75mm thick PCC (1:3:6 type C-1 (using 40 mm graded crushed stone aggregate) as in plinth protection or similar places, and finishing the surface even and smooth without using extra cement including making joints 12mm wide to the full depth of PCC at every 3 meters and at every change of direction and filling the same with sealing compound grade 'A' including necessary formwork etc and including demolition of existing old cement concrete complete all as specified and directed.

Dismantling Floor,hearth or wall tiles including cement mortar bedding but not backing) complete all as specified.

M & L for Non skid ceremic colour jointless tile 7.00 to 8.00 mm thick (square/rectungular) area exceeding 0.18 Sqm but not exceeding 0.38 Sqm in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match . including 15 mm thick screed bed in cement mortar 1:6, complete all as specified.

M & L for Non skid ceremic colour jointless tile 7.00 to 8.00 mm thick (square/rectungular) area exceeding 0.18 Sqm but not exceeding 0.38 Sqm in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match. including 10 mm thick plaster in cement mortar 1:6, complete all as specified.

M & L for Non skid ceremic colour jointless tile 7.00 to 8.00 mm thick (square/rectungular) area not exceeding 0.11 Sqm, floor set and jointed in neat cement slurry and pointed in white or coloured cement to match. including 10 mm thick plaster in cement mortar 1:6, complete all as specified.

M&L for degital glazed ceramic coloured jointless wall tiles (300x450)x7mm thick as in vertical surfaces including 10 mm thick rendering in cement mortar 1:3 and set jointed in neat cement slurry and pointed in white or colored cement to match the surface of tiles complete all as specified.

M&L for PCC 1:4:8 type D-2 (using 40 mm crushed graded stone aggregate) as in sub base, filling in mass concrete complete finished even and fair all as specified and directed

Excavation in post holes (or similar holes) each n.exc 0.5 Cum getting out returing, filling in and ramming earth or brocken rubble mixed with earth around in layers not exceeding 25 cement mortar complete all as spd and directed.

Excavation in trenches n. exc 1.5m wide and n. exc 1.5 min deapth for foundation or for shaft etc n. exc 10 sqm on plan and n.exc 10 sqm in depth and getting out in soft/ loose soil complete all as specified & directed.

Returning, Filling in, with excavated soil including spreading leveling, watering and well ramming in layers not exc 25cm thick in soft/ loose soil complete all as spesified & directed.

Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed at a level n exc 1.5m above the starting point.

S&F Structural steel, rolled section as in main and cross beams, hips and jack rafters, purlins, hollow section, tubular section where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates conforming to Fe-410 W (Gde-E-250)all as specified and directed by Engineer-in-Charge.

S & F Rolled MS in Joist,Channel, angle or TEE sections fixed independently without connecting plates complete all as specified and directed confoming to Fe-290 Gde E-165.

M & L for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes,with riveted, bolted or welded attachment Fe- 290 (Gde E- 165).

M&L for Steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt weled tubes conforming to IS. 1161-1998 grade St-240.

M&L for PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) filling in post holes, etc similar work complete all as specified.

M&L for Hardcore of broken stone or boulders of gauge n exc. 63mm, deposited, spread and leveliled in layers n exc. 150mm thick, watered and rammed to a true surface below floor sub base and plinth protection, all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D2 (using 40mm graded crushed stone agg) as in sub-bases all as specified and directed.

M & L for 25 mm thick Cement concrete 1:2:4 type B-1 (using 40mm graded crushed stone aggregate) as in floor for levelling surfaces complete all as specified.

M&L for Vitrified exterior colour tile (parking tiles) of size 30 cm x 30 cm x 8 to 9 mm thick set jointed and pointed in neat cement slurry in floors with white cement and pigments over and including screed bed or bedding layer or mortar 15 mm thick in cement mortar 1:6 including dismantling existing floor/tile complete all as specified and directed.

M&L for Rubberised prepolished coloured precast cement concrete Interlocking paver blocks of any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 grade complete with and including 25mm thick sand cushioning layer including dismantling of existing damaged flooring etc complete, all as specified and directed. Make:- Tulip infrastructure saharanpur, Mehtab tiles, NTC tiles Panchkula

M & L for RCC 1:2:4 Type B-1 (using 20mm graded crushed stone agg) as in lintels upto 1.50 M clear span cills, steps seismic and other similar bands, plinth coarses, string courses, lacing courses parapet and railing upto 60 Cm in height, cooping, kneelers, apex stone, bed plates, kerbs, roof curved, rouded or chamfered on edges complete all as spd. and directed.

M & L for mild steel TMT bars,8mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed ) not less than 0.9mm dia or securing with clips quality conforming to Grade-I IS-432 (Part -I), complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from frame) area n'exc 1.5 Sqm complete all as specified and directed.

Taking down chowkats or frame exc. 1.5 Sqm but n.exc 4 Sq m each with shutters (without taking off shutters from the fames)

S&F Pressed steel frames for doors(125x60) mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed etc complete.

S&F 2nd class hard wood 35mm thickness of factory made plain framed, panelled shutter with lock rail and panel of 9 mm BWP commercial ply or 12mm veneered partical board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified.

S & F 35mm thick factory made IInd class hard wood glazed/guage skeleton shutters, open rebated and prepared to receive glass, gauge etc. (with sash bars), divided in to square, edges of framing plain, chamfered or rounded ,fitted with cut and mitered bead for securing glasses etc, window ventilators etc are provided with stiles and rails as specified in SSR Part-I, 1991, Section- 8, Clause 8.20(b), complete all as specified and directed.

S & F Steel windows box type with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars dovetailed or welded incl cutting holes in wall for inserting holdfast and making good to the dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required. Make:-M/S Ashish Ind Ghaziabad M/S Ashwani & sons, E-16, Patel Nagar-II, Ghaziabad M/S Trishul Industries Ltd Meerut

S & F Steel windows box type with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded incl cutting holes in wall for inserting holdfast and making good to the dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required. Make:-M/S Ashish Ind Ghaziabad M/S Ashwani & sons, E-16, Patel Nagar-II, Ghaziabad M/S Trishul Industries Ltd Meerut

S & F framed work such as grills, gratings, etc .with ends of bars shouldered and/ or riveted , or forget into spikes ; framed guard bars barallel iron doors and similar work conforming to Fe.290.Gde-E-165

Supply and fix 100mm long butt hinges medium weight stainless steel all as specified and directed. Make:- Aluminium Udhyog New Delhi Mohan Metal Industries (Brand- Crown) Argent Industries New Delhi

S & F 200mm long stainless steel barrel tower bolts specified and directed.Make:- Aluminium Udhyog New Delhi,Mohan Metal Industries (Brand- Crown) Argent Industries New Delhi

S & F 150mm long stainless steel handle, complete all as specified. Make:- Aluminium Udhyog New Delhi Mohan Metal Industries (Brand- Crown) Argent Industries New Delhi

M & L 300mm long aluminium alloy anodised sliding door bolt, plate type stove enamelled black with bright bolt not less than 12mm dia and including minimum 6 bolts and nuts etc all as specified and directed. Make:- Aluminium Udhyog New Delhi Mohan Metal Industries (Brand- Crown) Argent Industries New Delhi

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing .

S & F steel Ventilator with Top hung shutters including projecting type hinges with steel handle, and steel peg stay complete with glazing bars dovetailed or welded comlete all as spd and directed.

S & F 3mm thick sheet glass ordinary quality glazing in square exc. 0.5 sqm in each pane all as specified.

S&F galvanized mild steel wire cloth 0.56 mm nominal dia and average width of aperture 1.18 mm and fixed with tinned tacks, complete all as specified.

S & F in repairs PVC connection 15mm size & length 450mm long with PTMT nuts, complete all as specified.

S & F in repairs PVC (SWR) bend 75 mm any radius complete all as specified.

S & F in repairs PVC (SWR) junction single,(Single T) 75 mm equal or unequal,complete all as specified.

S & F in repairs 75 mm dia PVC (SWR) pipes sigle socketed in any length with rubber ring joints Fixed to walls complete all as specified and directed.

S & F in repairs for 100 mm dia of grating doom of PTMT (minimum weight 25 gms) all as

S & F in repairs PVC waste pipe of 32 mm dia PVC socket complete all as specified and directed.

S & F in repairs 15 mm bore pillar cock fancy type cast copper alloy with capastan head,chromium plated, screw down, high pressure, screwed for iron pipe of 15 mm bore with all complete all as specified. Make:-Make:- Jaquar Essco (Orbit series)/ Cera(Victor series)/Prayag (7000 series Salasa)

S & F in repairs and 15 mm bore fency type bib tap chromium plated screwed down high pressure with crutch or capastan handle screwed both ends for iron 15 mm bore pipe or for unions all as specified. Make:-Make:- Jaquar Essco (Orbit series)/ Cera(Victor series)/Prayag (7000 series Salasa)

S & F in repairs 15 mm bore stop valves/angle cock cast copper alloy chromium plated fency type screwed down high pressure, with crutch or capastan handle screwed both ends all as specified. Make:-Make:- Jaquar Essco (Orbit series)/ Cera(Victor series)/Prayag (7000 series Salasa)

S & F in repairs 15mm bore galvanized steel tubing, medium grade with all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and directed.

S & F in repair rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoised and fixed in position of capacity 500 Ltr all as spd incl dismantling of existing water tank.

S & F in repairs 15mm ball brass valve high pressure with polyethlene float flynut complete screwed with iron pipe or brass ferrule and all as specified.

M & L in repairs floor Trap, plain with grating including jointing with solvent cement.

M&L for liquid soap container of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified.

S & F in repairs vitreous China wash down water closet pan (Pedestal Pattern) white with plastic water closet seat, black, closed pattern with recessed bottom, and cover mild steel chromium plated or aluminised hinging device(excluding fixing bolt flushing cistern and flush pipe Complete all as specified.

S&F 10 litre capacity PVC valve less syphlonic action type flusing cistern low level white with inlet ball valve, float, handle including brackets etc fixed in repairs complete all as specified..

S & F Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms).

S&F stainless steel curtain rod, 25 mm dia,decorative incl brackets, decorative finials at both ends. Incl. dismantling of existing rod.etc.

M & L for screened (stone, aggregate free) earth filling in depressed area of short range and embankment including leveling, remming, watering and consolidation in layers n.exc 25Cm thick,incl rolling incl excavation and removal of existing soil complete all as directed. Earth shall be taken from out side of defence land up to 10 km distance. Note :- Rate shall be included excavation earth work, transportation and depoiste material to given site

M&L for rendering 15 mm thick on fair face of brick work or concrete surface in cement mortar 1:4 finishing surface fair and even upto the height of 7.5 m complerte all as specified all as specified.

M&L for preparation of new surfaces and applying two coats of cement base paint over one coat primer on wall/ceiling, complete all as directed, upto height of 10 mtr.

M & L for 40 mm thick PCC (1:2:4) type B-1 (using 20 mm graded crushed stone agg) as in floor and finished the surface even and smooth with using extra cement all as specified.

M&L for 18 to 20mm thick machine cut kota stone slab 605 mm x 605 mm size on floor top, step etc over and incl 15mm thick bedding layer cement mortar 1:6 in roughening of old concrete floor surfaces by picking , sweeping clean and washing down with water to remove dust including brushing neat cement slurry with 3 kg/sqm with pigments to match the shade of slab including cutting, rubbing and mirror/granite finish polished complete all as specified and directed.

All as per item No 90 above but on vertical surfaces such as skirting, dado, riser etc over and including 15mm thick cement plaster in cement mortar 1:4 rough finisher surface to receive tiles.

Aggrawal Builders and Furnishers

M/s Vinod Singh Negi

M/s RK ENTERPRISES

G S CONSTRUCTIONS

M/S PUNDIR BUILDERS

Sharda Enterprises

Alankar Traders