C/O 12 Nos type-II Qtr. of HPPWD at Jail road Mandi HP

Amount

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m (one point five metre) in width or 10 Per square metre (ten square metre) on plan), including dressing of sides and ramming of bottoms, lift upto any metre, including getting out the excavated soil and disposal of surplus excavated soils as directed, within any lead . All kinds of soil 50% & Ordinary rock 50% (taking avg rate of 2.8.1 and 2.9.1) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Earth work in surface excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm (thirty centimeter) in depth, 1.5 m (one point five metre) in width as well as 10 Per square metre (ten square metre) on plan) including getting out and disposal of excavated earth lead upto any metre) as directed by Engineer-incharge. (taking avg rate of 2.6.1 and 2.7.1) All kinds of soil 50% & Ordinary rock 50% including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto any lead, including getting out the excavated soil, and then returning the soilas required, in layers not exceeding 20 cm (twenty centimetre) in depth, including consolidating Each deposited layer by ramming, watering, etc. and disposing of surplusexcavated soil as directed, within any lead. All kinds of soil. Pipes, cables etc. exceeding 80 mm (eighty millimetre) dia. but not exceeding 300 mm (three hundred millimetre) dia including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Centering and shuttering including strutting, propping etc. and removal of form for including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Foundations, footings, bases of columns, Per square metre etc. for mass concrete

Suspended floors, roofs, landings, balconies and acceess platform

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral- staircases

Lintels, beams, plinth beams, girders, Per square metre bressumers and cantilevers

Providing and laying in position cement concrete 1:5:10 (One cement : Five Coarse sand : Ten graded stone aggregate 40 mm (forty millimetre) nominal size) of specified grade excluding the cost of centering and shuttering - All work up to plinth level including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and laying 1:4:8 (One Cement : Four coarse sand) : Eight graded stone aggregate 40 mm (forty millimetre) nominal size) in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (I) All works upto plnth level. (Note :- Cement content considered in this item is @ 330 Per Kilogram/Per cubic metre (three hundred thirty kilogram per cubic metre). Excess/ less cement used as per design mix is payable/recoverable separately) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. ( I ) All works above plinth level upto Floor all level. (Note :- Cement content considered in this item is @ 330 Per Kilogram/Per cubic metre (three hundred thirty kilogram per cubic metre). Excess/ less cement used as per design mix is payable/recoverable separately). including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° (fifteen degree) landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (one cement : one point five coarse sand) : three graded stone aggregate 20 mm (twenty millimetre) nominal size). including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Coursed rubble masonry (second sort) with hard stone in foundation & plinth with : Cement mortar 1:6 (one cement : six coarse sand) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and laying factory made Precast concrete solid blocks of 200 mm (two hundred millimetre) thickness of grade M10 made of C&D waste from approved manufacturer in superstructure above plinth level up to floor all level Cement mortar 1:6 (one cement : six coarse sand) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and laying half block masonry with factory made Precast concrete solid blocks of 100 mm (one hundred millimetre) thickness of grade M10 made of C&D waste from approved manufacturer in superstructure above plinth level up to floor all level: Cement mortar 1:4(one cement : four coarse sand) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Second class teak wood including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm (four millimetre) thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Second class teak wood 35 mm (thirty millimetre) thick including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-incharge. (Note:- Butt hinges and necessary screws shall be paid separately) Second class teak wood 35 mm (thirty five millimetre) thick shutters including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm (twenty five millimetre to forty millimetre) thick : Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side, Grade I, Type II IS: 12823 marked including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm (twenty five millimetre to forty millimetre) thick : Float glass panes. 4 mm (four millimetre) thick glass pane (weight not less than 10 Per Kilogram per Per square metre) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm (one point four millimetre) in both directions with wire of dia 0.63 mm (Zero point sixty three millimetre), for doors, windows and clerestory windows with hinges and necessary screws : 35 mm (thirty five millimetre) thick shutters. with ISI marked M.S. pressed butt hinges bright finished of required size including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing cup board shutters 25 mm (twenty five millimetre) thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked, exterior grade (Grade l Type ll), having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm wide x12 mm (twenty five millimetre wide into twelve millimetre) thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charge

Providing and fixing 18 mm (eighteen millimetre) thick, 150 mm (one hundred fifty millimetre) wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, IS : 3087 marked, including top cover of 6 mm (six millimetre) commercial ply wood conforming to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm (twenty millimetre) dia ( heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm (twenty five into three millimetre) M.S. flat 10 cm (ten centimetre) long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm (one hundred millimetre into forty millimetre into forty millimetre) on both inner side of pelmet and rawl plugs 75 mm (seventy five millimetre) long etc. all complete. including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately). 6 mm (six millimetre) thick Cement bonded wood particle board as per IS:14276 including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc. including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing 250x16 mm (two hundred fifty into sixteen millimetre) aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

250x10 mm (two hundred fifty into ten millimetre)

150x10 mm (one hundred into fifty into ten millimetre)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

125mm (one hundred twenty five millimetre)

100mm (one hundred millimetre)

Providing and fixing bright finished brass helical door spring (superior quality) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing 150 mm (one hundred fifty millimetre) bright finished brass hard drawn hooks and eyes including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing 115 mm (one hundred fifteen millimetre) oxidised M.S. hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing PTMT door catcher of length 72 mm(seventy two millimetre) dia. of 42 mm (forty two millimetre) with suitable washers weighing not less than 33 gms (thirty three grams) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Boulder filling under floors tightly hand packed including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Cement concrete flooring 1:2:4 (one cement : two coarse sand : four graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm (forty millimetre) thick with 20 mm (twenty millimetre) nominal size stone aggregate including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm (twenty millimetre) thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 Per Kilogram/ Per square metre (three point three kilogram/Square metre) including grouting the joints with white cement and matching pigments etc., complete Size of Tile 600x600 mm (six hundred into six hundred millimetre) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm (twelve millimetre) thick bed of cement mortar 1:3 (one cement: three coarse sand), jointing with grey cement slurry @ 3.3 Per Kilogram/ Per square metre (three point three kilogram/square metre) including grouting the joint with white cement & matching pigments etc. complete Size of Tile 600x600 mm (six hundred into six hundred millimetre) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing 18 mm (eighteen millimetre) thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm (twenty millimetre) thick base cement mortar 1:4 (one cement : four coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade : Area of slab over 0.50 Per square metre (zero point fifty square metre) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Cement plaster skirting up to 30 cm (thirty centimetre) height, with cement mortar 1:3 (one cement : three coarse sand), finished with a floating coat of neat cement. 18 mm (eighteen millimetre) thick including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 40 mm (forty millimetre) wide and 4 mm (four millimetre) thick including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and laying full body vitrified floor tiles out of single piece tread and riser 150cm (one hundred fifty centimetre) long with anti skid pattern (with matt finish)of approved shade of jhonson/kajaria/AGL/RAK or equavalent, (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm (twenty millimetre) thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 Per Kilogram/ Per square metre (three point three kilogram per square metre) including grouting the joints with white cement and matching pigments etc., complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Applying cement slurry on R.C.C. slab or cement concrete work using 2.75 Per Kilogram. (two point seventy five kilogram)of cement per square metre of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing 0.62mm (zero point sixty two millimetre) thick troughed prepainted steel sheet roofing, with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (twenty) microns over 5 (five) microns primer coating to back coat of polyster of 5 (five) microns over 5 (five) microns primer coating, including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge including all leads, lifts and carriage of materials and other incidentals.

Providing and fixing ridges or hips 60 cm (sixty centimetre) overall with 0.62mm (zero point sixty two millimetre) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 (five) microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6mm (six millimetre) dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charges including all leads, lifts and carriage of materials and other incidentals.

Providing and fixing valley 90 cm (ninety centimetre) overall 0.62mm (zero point sixty two millimetre) thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 (five) microns primer coating back coat of polyster of 5 microns over 5 microns primer coating inclluding fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-charge including all leads, lifts and carriage of materials and other incidentals.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millimetre) gap for thermal expansion, 110 mm (one hundred ten millimetre) diameter Single socketed pipes including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing 110 mm (one hundred ten millimetre) bend on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millimetre) gap for thermal expansion including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

ProvProviding and fixing 100 mm (one hundred millimetre) diameter M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm (ten into ten into ten centimetre) of 1:2:4 mix (one cement : two coarse sand : four graded stone aggregate 20 mm (twenty millimetre) nominal size) and cost of cutting holes and making good the walls etc. including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing 15 cm (fifteen centimetre) wide, 45 cm (forty five centimetre) overall semicircular plain G.S. sheet gutter with iron brackets 40x3mm (forty into three millimetre) size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. 0.63 mm (zero point sixty three millimetre) thick with zinc coating not less than 275 gm/m² (two hundred seventy five grams/square metre) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm (one point sixty six millimetre to two millimetre) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm (twenty into ten into two millimetre) and braced with flat iron diagonals 20x5 mm (twenty into five millimetre) size, with top and bottom rail of T-iron 40x40x6 mm (forty into forty into six millimetre), with 40 mm (forty millimetre) dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 Per square metre (zero point ninety litre/ten square metre) over an under coat of primer applied @ 0.80 ltr/ 10 Per square metre (zero point eighty litre/ten square metre) of approved brand and manufacture including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Applying priming coat with ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 Per square metre (zero point ninety litre/ten square metre) over an under coat of primer applied @0.75 ltr/10 Per square metre (zero point seventy five litre/ten square metre) of approved brand and manufacture including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

6mm (six millimetre) cement plaster of mix: 1:3 (one cement : three Fine sand) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

15 mm (fifteen millimetre) cement plaster on rough side of single or half brick wall of mix: 1:6 (one cement: six coarse sand) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

15 mm (fifteen millimetre) cement plaster on fair side of single or half brick wall of mix: 1:6 (one cement: six coarse sand) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 Per square metre (one point sixty seven litre/ ten square metre) over and including priming coat of exterior primer applied @ 2.20 Per Kilogram/10 Per square metre (two point twenty kilogram/ ten square metre) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

15 mm (fifteen millimetre) cement plaster on rough side of single or half brick wall finished witha floating coat of neat cement of mix : 1:4 (one cement: four fine sand) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Making plinth protection 50mm (fifty millimetre) thick of cement concrete 1:3:6 (one cement : three coarse sand (zone - III) : six graded stone aggregate 20 mm (twenty millimetre) nominal size) over 75mm (seventy five millimetre) thick bed of dry brick ballast 40 mm (forty millimetre) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall. 15x22 cm (fifteen into twenty two centimetre) in cement mortar 1:6 (one cement : six sand) and inside plastring with cement plaster 1:3 (One Cement : Three Sand) including earth work and laying 10 cm (ten centimetre) cement concrete in 1:5:10 (One Cement : Five Sand : Ten graded stone aggregate) of 40 mm (forty millimetre) nominal size) and 7.5 cm (seventy five centimetre) cement concrete 1:2:4 (one Cement : twenty Sand : forty Graded stone aggregate of 20 mm (twenty millimetre) nominal size) and finished with a floating coat of neat cement complete as per standard design including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm (one hundred millimetre) sand cast Iron P or S trap, 10 (ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm (five hundred eighty into four hundred forty millimetre) with integral type foot rests including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing toilet paper holder : CP Brass including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing wash basin with C.I. brackets, 15 mm (fifteen millimetre) dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China Wash basin size 550x400 mm (five hundred fifty into four hundred millimetre) with a 15 mm (fifteen millimetre) CP Brass single hole basin mixer including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm (forty millimetre), including painting of fittings and brackets, cutting and making good the walls wherever required, Kitchen sink without drain 610x 460 mm (six hundred ten into four hundred sixty millimetre) bowl depth 200 (two hundred) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing in position 25 mm (twenty five millimetre) diameter mosquito proof coupling of approved municipal design including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing CP brass Waste Coupling for wash basin and sink, of approved quality.Waste coupling 31 mm dia of 79 mm (thirty one millimetre diameter of seventy nine millimetre) length and 62mm (sixty two millimetre) breadth weighing not less than 45 gms (forty five grams) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing 600x450 mm (six hundred into four hundred fifty millimetre) beveled edge mirror of superior glass (of approved quality) complete with 6 mm (six hundred millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm (four hundred fifty millimetre) long towel rail with total length of 495 mm, 78 mm (four hundred ninety five millimetre, seventy eight millimetre) wide and effective height including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing 600x120x5 mm (six hundred into one hundred twenty into five millimetre) glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm (forty millimetre) long screws, rawl plugs etc., complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and Fixing CP Soap dish of approved quality complete in all respect including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing C.P. brass shower rose with 15 or 20 mm (fifteen or twenty millimetre) inlet 100MM (one hundred millimetre) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm (fifteen millimetre) nominal bore including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm (forty five centimetre) length 15 mm (fifteen millimetre) nominal bore including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing brass stop cock of approved quality including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

15mm (fifteen millimetre) dia

20mm (twenty millimetre) dia.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

90mm dia (ninety millimetre) diameter

110mm dia (one hundred ten millimetre) diameter

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm (three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

90mm dia (ninety millimetre) diameter

110mm dia (one hundred ten millimetre) diameter

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

90mm dia (ninety millimetre) diameter

110mm dia (one hundred ten millimetre) diameter

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete including fixing with approved adhesive etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

90mm dia (ninety millimetre) diameter

110mm dia (one hundred ten millimetre) diameter

Providing and fixing PVC single equal branch , ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete including fixing with approved adhesive etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

90mm dia (ninety millimetre) diameter

110mm dia (one hundred ten millimetre) diameter

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc.complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

90mm dia (ninety millimetre) diameter

110mm dia (one hundred ten millimetre) diameter

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm (ten into ten into ten centimetre) of 1:2:4 mix (one cement : two coarse sand : four graded stone aggregate 20 mm (twenty millimetre) nominal size), including cost of cutting holes and making good the walls etc. including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

90mm dia (ninety millimetre) diameter

110mm dia (one hundred ten millimetre) diameter

Providing and fixing 110mmX90mm (one hundred ten millimetre into ninety millimetre) PVC floor trap of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing 125 mm (one hundred twenty five millimetre) nominal dia with 25 mm (twenty five millimetre) waste hole CP grating of approved quality. Circular type including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one point five coarse sand (zone-III) : three graded stone aggregate 20 mm( twenty millimetre) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone-III) : eight graded stone aggregate 40 mm (forty millimetre) nominal size), inside plastering 12 mm (twelve millimetre) thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20 mm (twenty millimetre) nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm (ninety into eighty centimetre) and 45 cm (forty five centimetre) deep including C.I. cover with frame (light duty) 455x610 mm (four hundred fifty five into six hundred ten millimetre) internal dimensions, total weight of cover and frame to be not less than 38 Per Kilogram (thirty eight) (weight of cover 23 Per Kilogram (twenty three kilogram) and weight of frame 15 Per Kilogram (fifteen kilogram)) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL-PE Composite tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 1000 ltr (one thousand litre) tank including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing 15mm dia (fifteen millimetre diameter) G.I. Pipes complete with G.I. fittings and clamps, including making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing 20 mm dia (twenty millimetre diametre) G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing 15 mm (fifteen millimetre) nominal bore ball valve (brass) of approved quality, High or low pressure, with plastic floats complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge.

SURENDER PAL

DHARMENDER KAPOOR