ADDN ALTN TO EE ROOM COMPLEX AND RE ROOFING OF CORRIDOR AND TRANSFORMER ROOM OF A TECH BUILDING AND ASSOCIATED B AND R WORK AT AF STN SAMANA UNDER GE (AF) JAMNAGAR NO 1

Amount

M&L for complete removal of existing treatment of any thickness laid over RCC/Roof chajja cleaning and washing of roof with water to remove dust etc as preparation to receive treatment, brooming down or steel wire brushing, scraping down smoke soot, mouls, moss and efflorescent salts and treating oil and greasy spots complete all as specified and as directed.

M&L for brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and directed.

M&L for PCC in roof pading, coving,filling and mass concrete type B-0, 1:2:4 (using 12.50mm graded stone aggregate) complete all as specified and directed

M&L for plaster/ screed 10mm thick on concrete surface in CM 1:4, finishing the surface even and smooth without using extra cement, including mixing only liquid water proofing compound as per manufacture instruction complete all as specified and directed Note WPC will be measured & paid separately.

Supply only integral water proofing chemical @ 200ml/Bag of cement complete all as specified and directed.

M&L for water proofing treatment to RCC roof slab all as specified below and as directed:- (a) Apply one coat of glass fibre base bitumen felt primer, grade 2 @ 0.25 Kg/Sqm. (b) Laying APP based ploymeric membrane 3mm thick, minimum wt 3.00 kg/Sqm reinforced with polyester non-wove fabric (weighing not less than 150gms/Sqm ) uniformly embedded during manufacturing process, laid on primed roofs & flashing by forced application having side overlap 100mm and at the end 150mm using Butane torch, and sealing all joints and overlaps (c) Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3, complete all as specified and as directed

Dismantling wall and ceiling board (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets and assesories etc. Note:- Quoted rate deemed to carryout work at height upto 8.00 m

S&F 600x600mmx4mm thick false ceiling of Non esbestos fibre cement building boards (E Board) and including anodised aluminium powder coated (minimum thickness of powder coating 50 micron) snap grid frame work of T section (main & cross member) of size 25 mm x 25 mm x 1.5 mm thick in square pattern of grid size 605mm X 605mm . The aluminium frame work will be supported on side wall with the use of aluminium 'L' section of size 25 mm x 25 mm x 1.5 angles etc. Snap grid shall be supported with hangers of 4 mm dia. Galvanised iron wire adjusting level fixed to roof slabs / truss etc by means of ceiling cleats made out of Galvanised iron flat of size 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long, directed by the Engineer-in-Charge. Note:- Quoted rate deemed to carryout wk at height upto 8.00 m

S&F for 12mm thick perforated particle board/ tiles for insula-tion and accoustic purposes, 60x60 cm in size, fixed with screw to timber frame work or with staples on snap grid complete all as specified and as directed

Dismantling timber scantlings, fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section, complete all as specified and as directed.

M&L for second class hardwood in scantling in timber frame work fixed with screw complete all as specified and as directed.

Dismantling of floor, hearth or wall tiling or stone slab laid, bedded & pointed in any mortar including demolition of cement mortar bedding or backing coat, including removal of debries to a distance exc 1.5 km but n.exc 2 Km complete all as spd and directed.

M&L Rendering 10mm thick in CM 1:4 on on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing for skirting/dado etc complete all as spd and directed

M&L for Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6 complete all as spd and directed

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 300X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as spd and directed

M&L for Non skid, coloured ceramic tiles 7 to 8 mm thick (Square / rectangular) polished area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors etc laid over and pointed with coloured cement to match the tiles complete all as spd and directed

M&L for non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

M&L for 2mm thick linoleum, plain coloured, laid on floors, linoleum is sealed down with an approved adhesive including stretching, cutting and fitting, cplete all as specified and directed.

Demolition of RCC of any descrition such as Kitchen chimniy, chajja, shelves, OHT Tanks,Pilar,wall, column.beam, chajja/ roof projection drops etc and in any position not other wise specially provided for complete all as specified and directed by Engineer in Charge (reinforcement cut as required to facilitate demolition)Note:- Quoted rate deemed to carryout wk at height upto 8.00 m

Reinforcement cement concrete type B1 1:2:4 using 20mm aggregate as in slab supported on walls beams and columns in floor, roof, landing and in shelves, chajja, lintel and similar works complete all as specified and directed by Engineer-in-Charge Note:- Quoted rate deemed to carryout wk at height upto 8.00 m

S&F mild steel TMT bar 10mm dia and over cut to length bent to shape required including cranking bending spirally and binding with and including mild steel wise (annealed) not less than 0.9 mm dia complete all as specified and directed by Engineer-in-Charge

Form work to sofites of suspended slab such as roof slab, floor slab , landing, chajjas, lintel and similar work for rough finish surface.complete all as specified and directed by Engineer-in-Charge

M&L 15 -18mm thick granite stone slab of any type (cut, table rubbed and polished)in steps, jambs, pillars, window cills, cooking platforms and like , bedded & jointed with grey cement slurry & pointing with coloured cement using marble dust with admixture of pigment to match with marble shade; laid over complete all as spd and directed

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm in repair complete all as specified and as directed

Taking down cement plaster of any thickness in cement or cement lime mortar on brick or stone or concrete walls etc. including raking out joints, hacking for key, scrubbing down with water etc, including removal of debries to a distance exc 1.5 km but n.exc 2 Km, complete all as spd and directed Note:- Quoted rate deemed to carryout wk at height upto 8.00 m

M&L for rendering 15 mm thick on stone masonary or concrete surface of walls in cement mortar 1:6 finished complete all as spd and directed

M &L 2 coats of oil bound distemper on new surfaces of walls over a coat of primer including preparation to distempering to match with existing work complete all as specified and directed

M & L rendering 10 mm thick in patches on fair faces of brick or concrete surfaces in CM 1:3 as on ceiling, facia roof projection etc finished even and smooth without using extra cement as directed by Engineer-in-Charge.

M &L 2 coats of oil bound distemper on new surfaces of ceiling including preparation to distempering to match with existing work complete all as specified and directed

M&L for rendering 15 mm thick on stone masonary or concrete surface of walls in cement mortar 1:4 finished complete all as specifed and directed Note:- Quoted rate deemed to carryout wk at height upto 8.00 m

M&L for rendering in cement mortar (1:4), 10mm thick as dubbing out coat on brick work other than fair face or on cement concrete surface including 10mm thick floating coat in CM (1:3) over dubbing out coat mixed with water proffing compound finished even and smooth.complete all as specified and directed Note :- water proofing compound will be measured and paid separately.

S&F welded steel wire fabric weight n. exc. 4 kg per sqm supplied and fixed complete to wood or steel members, conrete/ stone wall surface complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) and pattern (camo) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new/old surfaces walls/fins/facia/soffit/chajja etc complete all as specified and directed Note:- Quoted rate deemed to carryout wk at height upto 8.00 m

M&L for Preparation of old distempered / decorated surfaces of walls and applying Two coat of Distemper oil emulsion complete as specified and directed.

M&L for Preparation of old distempered / decorated surfaces of ceiling and applying Two coat of Distemper oil emulsion complete as specified and directed.

Supply & fix Fibre glass mesh of 145 gsm for plastering work etc complete all as spd all directed

Dismantling mild steel rolling shutter of any description not otherwise specifically provided for complete all as specified & directed.

S&F 1.25mm thick steel rolling shutters, with ball bearing, including top cover, safety lever locks mild steel with 4 levers for rolling shutters as specified, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indi?cated, complete: push pull or manual type

Taking down chowkats or frame with shutter of any description (without taking out shutter from the frame) not exceeding 1.50 sqm each and removal from site complete all as specified and directed Engineer-in-Charge

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 sq. m but n exc 4 sq. m each complete all as specified and directed.

Taking down shutter of any description exc 1.00sqm but n exc 2.00 sqm each complete all as specified and directed by Engineer-in-Charge

Taking down Aluminium/ steel windows/ ventilator with shutters and frames including glass panes/ wire gauge etc complete all as wire gauge etc complete all as specified and as directed

S & F for factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube fixed in opening complete as per manufacturer's specifications and as directed by Engineer-in-Charge

S&F Factory Made Solid PVC Moulded Door Shutter with wood free EPS core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site complete all as specified and directed

S&F 30mm thick. flush shutter, solid core construction with particle board core and ply woood face panels commercial type on both side complete all as specified and directed Engineer-in-Charge

S&F 30 mm thick second class hardwood factory made Glazed and skeleton door shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass / gauge, etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), fitted to chowkats complete.

M&L for preparing new surfaces of wood or wood based materials of any description not other wise described over 10 CM width or girth new or previously un treated wooden surfaces and applying one coat of pink primer and two coat of synthetic enamel paint complete all as specified & directed.

M&L for preparation of old painted wooden surfaces, exc 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and as directed by Engineer-In-Charge.

S&F 100mm butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified & directed.

S&F 100 mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified & directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified & directed.

S&F 125 mm in size aluminium handles cast type anodized complete all as specified & directed.

S & F 250 mm mild steel sliding bolt plate type stove enamelled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts four on bolt plate and two on stapple plate and fixed complete all as specified and directed by Engineer-in-Charge

S&F door closer hydraulically regulated designation No 2, aluminium (Die cast) body, universal type suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 Kg fixed in repair complete all as specified & directed.

S&F 200mm, ordinary MS rat tail rod pattern springs including roller and roller plate in repaircomplete all as specified & directed.

S& f aluminium powder coated (of any color, thickness of powder coating not less than 50 micron) frame for door,window and ventilators or similar wk with one or more rebate inc joining cleat for fixing in repair complete all as specified and directed by Engineer-in-Charge

S&F aluminium door shutters powder coated of any color ( thickness of powder coating not less than 50 micron), alumimnium section weighing min. 0.55 Kg/m including necessary joining cleats, glazing clips, rubbers packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc in repair complete all as specified.directed by Engineer - in - Charge.

S&F in repairs aluminium window and ventilator shutters or aluminium partition, powder coated of any colour (Thickness or powder coating not less than 50 micron),fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F aluminium window and ventilator shutters, powder coated of any colour ( thickness of powder coating not less than 50 micron) side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) in repair complete all as specified and as directed

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and as directed

S&F 12 mm prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations complete all as specified and directed by Engineer-in-Charge

S&F sheet glass 4 mm thick ordinary quality (plain/floated/frosted) and glazing with oil putty / wooden beads / aluminium glazing clip in square exc. 0.5 sqm in each pane complete all as specified & directed.

S&F in repair MS louvers of 80 mm wide & 4 mm thick frosted glass including aluminium louver patti for adjusting the louvers fixed in Aluminium ventilators with screws etc complete all as specified and directed by Engineer-in-Charge

S & F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aparture 1.18 mm and fixed with tinned tacks ro galvanised wire stapple complete all as specified and directed by Engineer-in-Charge

S & F in repair floor door stopper 140mm size of aluminium alloy body and tounge, anodised, with hard drawn steel spring complete all as specified and directed by Engineer-in-Charge

Dismantling water tanks exc 500 ltr and n.exc 1000 ltr and removing to store complete all as specified and directed

S&F 1000 ltrs capacity double layer, rotational molded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position over existing PCC platform incl all fitting such as connection pieces with GI tank nipple for inlet, outlet, etc complete all as specified and directed

S&F in repair 25mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed

S&F ball valves CPVC pipe outer diameter 32mm bore in repair complete all as specified and directed by Engineer-in-Charge

Taking up or down 15mm dia steel tubing and connections, including cleaning for refixing or removal from site complete all as spd and directed

S&F 20mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

Taking up or down 20mm dia steel tubing and connections, including cleaning for refixing or removal from site complete all as spd and directed

S&F 32mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

S&F in repair vitreous china wash basin, white, flat back, size 550 mm x 400 mm fixed on and including cast iron cantilever bracket 32 mm dia brass waste coupling and including waste pipe of suitable length complete all as specified and directed by Engineer-in-Charge

S & F in repairs vitreous China squatting pan of Orrissa pattern of approved make of size 580 mm X 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe incl lime concrete bedding and connection to antisyphonage pipe etc including making good to floor complete all as specified and directed by Engineer-in-Charge

S&F in repair vitreous china wash down water closet pan (pedestal pattern) white with CI 'P' or 'S' trap incl water closet seat cover of plastic,jet etc.complete incl necessary PVC waste pipe fitting, complete all as specified and directed by Engineer-in-Charge

S&F in repair 10 Litre capacity PVC symphonic action type flushing cistern, duel flush type (ISI Marked) low level with inlet ball valve, float and handle & PVC flush pipe, fixed in position and connecting complete all as spd and directed

S&F in repairs PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as spd and directed

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as spd and directed

S&F in repair 15mm size angular Stop valves, CP, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as spd and directed

S&F 15mm dia size two way angle valve brass chromium plated, fancy type complete all as specified and as directed.

S&F in repairs fancy type chromium plated, long shank & cup (concealed type) 15mm bore dia Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as spd and directed

S&F in repair 100 mm chromium plated swivel shower rose with or without swivel joints any size for fixing with 15mm pipe incl shower arm 15mm size, 195mm long with bend of 45 degree.

S&F in repair 15mm dia size Bib taps, CP, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as spd and directed

S&F in repair 15 mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as spd and directed

S&F in repair chromium plated soap tray any type and fixed to plugs on wall with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge

S & F in repair Tubular towel rail, 20mm dia, D type, 600mm long between flanges chromium plated complete all as spd and directed

S&F in repairs PVC waste pipe flexible type suitable for couplings 32 / 40 mm dia and 750 mm long complete all as spd and directed

Dismantling and disconnecting of existing cast iron or reinforced concrete drain pipes, jointed in cement mortar 75/100 mm dia bore fixed to wall,laid in trenches complete all as specified and directed Engineer-in-Charge

S&F PVC (SWR) pipes 75mm dia single socketed in any length with rubber ring joints laid in trenches or in floors in repair complete all as specified and directed

S & F 75 mm bore of pipe PVC (SWR) bends of any radius / shoe fixed to PVC pipes in repair complete all as specified and directed by Engineer-in-Charge

M&L for 75 mm dia of PVC (SWR) floor trap plain with grating incluing jointing with solvent cement in repair complete all as specified and directed by Engineer-in-Charge

S&F PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed on walls including clamp complete all as specified and directed

S&F PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed

S & F 110 mm bore of pipe PVC (SWR) bends of any radius / shoe fixed to PVC pipes provided with access door in repair complete all as specified and directed by Engineer-in-Charge

S & F 110 mm bore of pipe PVC (SWR) junction single,(Single T) equal or unequal fixed to PVC pipes with access door in repair complete all as specified and directed by Engineer-in-Charge

S & F 110 mm bore of pipe PVC vent cowl fixed to PVC pipes complete all as specified and directed by Engineer-in-Charge

Demolition of ashlar facings, dressed stonework, precast concrete articles and precast concrete block walling etc fixed in cement mortar including all quoins, pillars, arches etc. all as specified and as directed.

M&L for providing precast cement concrete (1:5:8) (using 20mm graded stone aggregate) solid building blocks exe 10 cm thick, in width (with plain or inter locking joints as directed) setting in CM 1:6 complete in wall or pillars or kerbstone all as specified and directed.

M&L for providing cement concrete type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges, coping etc, complete all as specified

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

Excavation in post holes in hard/dense (or similar holes) each n.exc 0.5 cum, getting out, returning, refilling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm in any type of soil removing surplus soil to a distance n exc 50 m complete all as specified and directed.

M&L for PCC 1:2:4 type C 2 using 40mm graded stone aggregate as in foundation, filling, mass concrete complete all as specified and as directed.

S & F Steel work in tubular/rectangular MS Pipe such as vertical post,trusses, rafter, purlins etc. including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1998 grade St-240 complete all as specified and directed Engineer-in-Charge

S&F Plates (Plain or chequered) channels,squarecut or notched (ordinary and counter sunk) forming holes, w/o any attachment conforming to FE-410-W( Gde-E-250 )quality -Acomplete all as specified and directed Engineer-in-Charge

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel, flat sections or plates etc) including distance pieces, cleats etc. Fe 410 -W (Gde-E- 250) quality- A complete all as specified and directed

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spiked framed guard bars barred iron doors ladders framed blasters walkways railings framework of water tanks and similar work conforming to Fe 290 Grade E-165

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/clading to wall, molding/folding in circular/semicircular of any position and height fixed with self tapping screws as specified, As directed by Engr-in-charge

S&F for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, and crumple joints fixed with self tapping screws complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings not exc 15cm thickness below or above ground level, including removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

M&L for 75mm thick cement concrete Type D2 ( 1:4:8) using 40mm graded stone aggregate as in subbase complete all as specified and as directed.

M&L for 100mm thick PCC 1:2:4 type B-2( using 20 mm graded stone aggregate) in loor hardstanding laid in alternate bay system, finish the surface fair and even and fair all as per specified.

M&L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade 'A'

Taking down carefully any aluminum /copper point wiring with conduits/casing caping & removing material/debris for taking credit and making good the disturbed surface of walls & floors etc to match with the original existing finish complete all as specified and as directed.

Taking down carefully by unscrewing from fitting and fixtures as switches,ceiling roses, pendents,regulators,bells, sockets, tube light fittings,false celing light fittngs,DB,MCB etc, for scdule of credit as directed by Engr in charge

Taking down carefully by unscrewing from fitting and fixtures as switches,ceiling roses, pendents,regulators,bells, sockets, tube light fittings,false celing light fittngs , AC duct grill any size,DB,MCB etc, for reuse at site or carrying to the store( To be found measured only when found serviceable in all rspect for reuse) and refixing all as specified and as directed

Taking down carefully by disconnecting smoke detectors, fire alam sensors,sounder, remote indicators ,fire alarm panel to store carefully and refixing re-install and testing it as per the direction of engineer in charge ) and refixing it all as specified and as directed

M & L for point wiring complete with 1.5 sqmm single core multistranded copper conductor FRLS, PVC insulated and unsheathed cable 650 /1100 volts grade drawn through & including super deluxe casing caping (not less than 25 mm wide) with all its accessories like bends, tees, suitable module PVC boxes o etc fix on wall or ceiling surfaces all as specified including 1.5 sqmm , FRLS type , copper multistranded cable as earth wire and plastic laminated PVC box with cover plate as specified and directed by Engr -in charge:

(a) One light / fan / exhaust fan point controlled by one, one way switch.

(d) One 3 pin socket out let 5 Amps on the independent board.

All as per item No 119 above but with 4.0 sqmm multistranded copper multistranded conductor FRLS cable with 4 sqmm earth wire for one 6 pin socket outlet 15 amps on independent board as specified and directed by Engr -in charge:

S & F switch Piano 5 Amps, flush button type, SP, one way, 230 Volts complete as specified and directed by Engr -in charge.

S & F Switch socket combination multipurpose 5 pin 5 Amps, flush type, 230 / 250 Volts complete as specified and directed by Engr -in charge.

S & F switch socket combination ,6 pin ,15 amps, flush type, multipurpose, 230 / 250 volts complete as specified and directed by Engr -in charge.

M&L for Ceiling rose, 3 terminal polycarbonate body 6 Amps, 250 volts AC, including connecting complete as specified and directed by Engr -in charge.

S & F stepped type electronic fan regulator flush type as diretecd by engineer in charge.

Supply and fix sheet metal enclosure MCB DB, single pole and neutral, 12 ways double door 240 volts having 200 Amps rated bus bar with balnking plates wherever required and degree of protection I.P 43 -IK 09 with acrylic cover as including all connectionsas directed by engineer in charge

Supply and fix MCB single pole 240 volts 6 to 32 Amps (to be fixed as per load requirement) 220V with 'C' curve complete as including all connectionsas directed by engineer in charge

Supply and fix MCB Single pole Neutral 240 volts 40- 63 Amps (to be fixed as per load requirement)220V with 'C' curve complete as including all connectionsas directed by engineer in charge

Supply & Fix energy efficient LED tube light fitting with built in LED & integral LED driver 20 watt, channel housing & diffuser of length 1200 mm (approx) with all accessories, fixing arrangement internally pre-wired, fixed in position & connecting complete all as specified and directed by Engg –in-charge.

Supply & Fix false celing light 600mmx600mm ,36 watt LED fitting with driver and , fixing arrangement internally pre-wired, fixed in position & connecting complete all as specified and directed by Engg –in-charge.

S&F LED building security in repair light fitting 60 Watt system efficiency not less than 100 lumen / Watt, IP66 protection, consisting of high / low voltage cut off, maintenance free isolated Electronic driver circuits, Low THD, PMMA grade high quality Transmittance lens, Epoxy powder coated Die Cast Aluminium housing with weather proof gasket for lamp & driver compartment, Heat resistance toughened glass fitted in cast aluminium housing with SS screws, pipe, bracket on building,

Supply and fixing for precast cemenet concrete(1:5:8)( usinng 20mm graded stone aggregate) solid building blocks of size 300mmx200mmx125mm for fixing of insulators,strip etc complete on wall/roof/pillers completed all as directed

Supply and fixing copper earth strip of size 20 x 3 mm with epoxy insulators and fixing screws etc on wall/ roof/ground etc including taking down old strip all as directed by Engr-in-charge

Taking down copper/aluminum strip any size with epoxy insulators and connecting itemsa from wall/floor/roof etc to store and refixing it with new insulators and connecting items along with brazing, bolting ,screwing as direted by engineer in charge.

Material and labour replacement for earthing complete with galvanized iron earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m deep below normal ground connected to galvanized steel wire 4 mm dia by means of bolts nuts check nuts and washer of galvanized steel, watering pipe of 20 mm bore, galvanised iron, light grade, and 15 mm bore galvanised iron light grade for earth wire protection including all excavation earth work in any type of soil, PCC pit in PCC 1:2:4 type B-1 and RCC 1:2:4, type B1 for precast chamber cover 50 mm thick, reinforced with welded steel wire fabric or XPM Jali (weight not less than 4.00 Kg / sqm), with charcoal, salt, funnel complete all as shown in the electrical plate No 3 of SSR part –I and testing on completion. ( Note- Quoted rates are deemed to include for earth strip with protection pipe up to 7.5m length)

Disconnecting & Taking out LT underground cable(aluminum conductor of size 25 to 70 sqmm any core from trenches including cable cover,tubes if any etc complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and n.exc 1.5m in depth for foundation / fixing pole / laying cable and pipe line etc or for man hole etc not exc 10 sqm on plan and getting out in soft / loose soil all as specified.

Returning filling in including spreading leveling, watering and well ramming in layers not exc 25 cm thick using suitable excavated soft / loose soil all as directed.

Removing excavated soil to a distance exc 50 m but n.exc 100 m and depositing where directed at a level n.exc 1.5m above the starting point.

M&L for providing dry river sand as in sand cushioning to under ground PVC cable including punning down of sand in layer all as specified and directed by Engg-in-Charge. (Note: for measurement purpose any punned thickness of sand will be considered.)

Supply & laying ISI marked & conforming to IS - 5820 - 1970 unreinforced precast concrete cable cover Class LV , Type I , flat size 250 mm X 150 mm X 40 mm in trenches as protection to LT UG cable all as specified and directed by Engr-in-Charge.

Supply & laying XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable, with aluminium conductor 1100 volt grade of size 70 Sqmm 3.5 core laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing etc complete all as specified & directed.

Supply, install, testing and commissioning and testing factory made and tested (including CPRI type test certified) in replacement, LT feeder pillar box (KIOSK) outdoor type, platform mounted, suitable for 415 Volts 3 phase 4 wire, 50 Hz AC supply system, all as specified and directed, having bus bar chamber with insulated copper bus bars 350 amps rating installed on porcelain insulators. The panel shall be dust and vermin proof, made of 3.15mm CRCA MS sheet 75mm x 30 mm thick MS Channel frame, duly powder coated finish. Front opening type with aprons for cable entry with double door shutter and locking arrangement, danger plate and earthing terminal . The scope of work includes pcc foundation and provision of the following :-Incoming (a) MCCB 4 pole 200 Amps, 36 KA, 415V -01 Nos (b) Bus bar (copper strip) 350Amp, 4 pole, for in comp supply 01 No (c) digital panel meter including CTs -01 No. Outgoing (b) Isolator TPN 63 Amp 9/10 KA, 415 V 50 HZ - 01 Nos (c) MCCB 63 amp 16 KA, 415 V 50 Hz - 04 No. (e) Existing cable (For various Bldg supply cable of sizes ) connect with busbar properly with suitable size copper Lug .

Supply and fix Light Grade 40 mm GI pipe for laying under roads , PCC, wall , pits, chambers etc either by boring or excavating surface and make it re-surfaced after laying

Material and labour in replacement for provision of earthing complete with galvanized iron earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m deep below normal ground connected to galvanised mild steel strip 25*4 mm by means of bolts, nuts, check nuts and washer of galvanized steel, watering pipe of 20 mm bore galvanised iron medium grade and 40 mm bore galvanised iron light grade for earth strip protection including.....

.....all excavation, earth work in any type of soil, PCC pit in PCC 1:2:4 type B-1 and RCC 1:2:4, type B1 for precast chamber cover 50 mm thick, reinforced with welded steel wire fabric or XPM Jali (weight not less than 4.00 Kg / sqm), with charcoal, salt, funnel complete all as shown in the electrical plate No 3 of SSR part –I and testing on completion. Note : (i)Earth result after installation completely should be less than 5 Ohm (Note - Quoted rates are deemed to include for earth strip with protection pipe up to 7.5m length)

S&F in repair aluminium three track Powder coated of any color ( thickness of powder coating not less than 50 micron) sliding window with three sliding shutter , the size of outer frame three track 92 x 31.5x 1.20mm ( using two track for glazed window shutter and one track for wire gauged ) , the section shutter size 37x 18x 1.2mm)and glazing with 4 mm thick glass ( plain/floated) including all-around suitable rubber gasket and MS wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4mm and fixed on aluminum flat and inserted in the frame of shutter with tracking arrangement each sliding window shall be provided with one number handle including locking arrangement & 2 numbers’s sliding rollers of nylon with including all necessary fittings complete all as specified and directed by Engineer-in-Charge

S&F sheet glass 4 mm thick ordinary quality(plain/floated/frosted) and glazing with oil putty / wooden beads / aluminium glazing clip in square n.exc. 0.5 sqm in each pane complete all as specified & directed.

S&F in repairs Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F 100 mm size mild steel body Mortise lock, vertical type, with 4 brass liver, fixed to aluminium door complete.

M&L for light shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors/dado /skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as spd and directed

M&L Green Marble work 15 to 18 mm thick (table rubbed and polished) in steps, jambs, pillars, window/door cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as spd and directed

M&L for preperation old decorated surfaces of walls, plastered or unplastered, roof etc by brooming down or steel wire brushes, scrapping down smoke soot, moulds, efflorescent salts etc and applying Two coat of Acrylic emulsion (exterior weather coat) paint in camouflage pattern (as approved by EIC) of any tint as approved complete all as specified and directed by Engr-in-charge. (Note :- Quoted rate deemed to carryout wk at height upto 8.00 m )

M&L for Preparation of old distempered / decorated surfaces of walls including washing, rubbing down and stopping holes, trading oil and greasy spots and applying Two coat of Distemper oil emulsion complete all as specified and as directed by Engr-In-Charge. (Note:- Quoted rate deemed to carryout wk at height upto 8.00 m)

M&L for Preparation of old distempered / decorated surfaces of ceiling including washing, rubbing down and stopping holes, trading oil and greasy spots and applying one coat of Distemper oil emulsion complete all as specified and as directed by Engr-In-Charge. (Note:- Quoted rate deemed to carryout wk at height upto 8.00 m)

M&L for prepration of old painted steel or Iron surfaces, exc 10 cm width or girth and applying one coat of synthetic enamel paint etc. all as specified and as directed by Engineer-In-Charge.

M&L for providing cement concrete type D-2, 1:4:8 (using 40mm graded aggregate) as in foundation filling and mass concrete etc complete.

M&L preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed

Dismantling of plain or corrugated steel sheeting any gauge, thickness, from roof coverings etc complete all as specified and directed.

Supply and fix sheet metal enclosure MCB DB, single pole and neutral, 04ways double door 240 volts having 200 Amps rated bus bar with balnking plates wherever required and degree of protection I.P 43 -IK 09 with acrylic cover as including all connectionsas directed by engineer in charge

Supply & Fix energy efficient bulk head LED fittings, 10 watt, with all accessories & fixing arrangements, internally prewired, fixed in position & connecting complete all as specified and as directed.

S&F LED building security in repair light fitting 100 Watt system efficiency not less than 100 lumen / Watt, IP66 protection, consisting of high / low voltage cut off, maintenance free isolated Electronic driver circuits, Low THD, PMMA grade high quality Transmittance lens, Epoxy powder coated Die Cast Aluminium housing with weather proof gasket for lamp & driver compartment, Heat resistance toughened glass fitted in cast aluminium housing with SS screws, pipe, bracket on building,

M & L for sub main wiring with two single core PVC insulated and unsheathed cable 2.50 sqmm with multi stranded copper conductor , FRLS type cable drawn through and includingPVC conduit complete with all accessories alongwith provn of 2.50 sqmm PVC insulated and unsheathed ,multi stranded copper conductor , FRLS type cable as earth wire and connecting to tbe BD with proper size of lugs/thimbles etc comnplete all as specified and directed.

Sagathiya Builders (BID ID -3171607)

Nitesh Enterprise (BID ID -3166054)