ADDN ALTN IMPROVEMENT TO COOK HOUSES OF OFFICERS MESS AND AIRMEN MESSES AT AFS BAREILLY UNDER GE (AF) BAREILLY

Amount

B/R PORTION Dismantling timber fillets, rails, posts, rafters, purlins, etc. 40 sqcm and over in section in any position (unframed work) complete all as specified

Dismantling structural steel work in cluding doors, gates but excluding framed truss etc. complete all as specified.

Dismantling plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof coverings complete all as specified.

M&L for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS:1161-1979 grade St.-240 complete all as specified.

S&F for prepainted galvalume aluminum zink coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self coaching screw complete all as specified.

Excavation in trenches in soft /loose soil not exc 1.50 m wide and not exc1.50 mtr in depth for foundation etc or for shafts, wells, cespits , manholes, pier holes etc not exc 10 sqm on plan and getting out complete all as specified.

Removing excavated material (soil) to a distance exc 250 meter but not exc 500 meters and depositing where directed at a level not exc 1.5 mtr above from the starting point complete all as specified.

Returning, filling in including spreading, levelling watering and well ramming in layer not exc 25 cm thick complete all as specified.

Spreading and leveling in layers (soil obtained from item No 6.00 above) not exc. 25 cm thick, well ramming including watering as required.

M&L for hardcore of broken stone broken or boulders gauge not exc. 63 mm, deposited, spread and levelled in layers not exc15 cm thick watered and rammed to a true surface complete all as specified.

M&L for plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete, sub base for flooring etc. all as specified.

M&L for 100 mm thick cement concrete 1:2:4 type B-1 (using 20 mm grade stone aggregate) as in floor including finishing surface even and smooth with using extra cement complete all as specified.

M&L for plain cement concrete, type D-2, 1:4:8 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete ,sub base floor complete all as specified.

Demolition of brick work built in cement mortar or cement lime mortar including all quions, arches, pillers etc and removing debris from site to out side MOD land complete all as specified.

Taking down cement plaster including racking out joints, hacking for key and scrubbing down with water and removing debris from site to out side MOD land complete all as specified.

M&L for brick work with sub-class `B' bricks, straight or curved on plan exc 6.0 mtr mean radius built in cement mortar 1:6 complete all as specified.

M&L for 15 mm thick rendering in cement mortar (1:4) on brick or concrete surfaces including finishing surface fair and even without using extra cement but including mixed with liquid WPC as per manufacturer instruction. (Note :- WPC will be measured and paid separately).

M&L for rendering 15 mm thick in cement mortar 1:6 in patch area not exc 2 Sqm including finishing surface even and smooth on brick or concrete surfaces without using extra cement complete all as specified.

M&L for 5 mm thick rendering in cement mortar (1:3) on concrete surfaces in ceiling including finishing surface even and smooth without using extra cement

Supply only liquid water proofing compound.

M&L for applying a coat of 3mm thick (average) wall care putty on wall for finishing the surface even and smooth with sand papering etc complete all as specified.

M&L for prepration of newly plastered surface of wall and applying two coats of cement base paint complete all as specified.

M&L for three coats of white wash on ceiling including preparation of newly plastered surfaces all as specified.

M&L for prepration of old plastered surface of wall and applying two coats of white wash complete all as specified.

M&L for prepration of newly plastered surface of wall and applying two coats of white wash on wall surfaces complete all as specified.

M&L for prepration of newly plastered surface on walls and applying two coats of oil bound distemper over a coat of wall primer complete all as specified.

Demolition of reinforced cement concrete of any description as roofs,floors (other than ground floors) beams, staircases, landings, chajjas and simillar suspended work and removing debris from site to out side MOD land complete all as specified.

M&L for mild steel TMT bar 10 mmm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, looking ends and binding with and inclu, mild steel wire not less than 0.90mm dia complete all as specified.

M&L for mild steel TMT bar 8 mmm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, looking ends and binding with and inclu, mild steel wire not less than 0.90mm dia complete all as specified.

All as per item No. 29 above but for 8 mm dia and over up to and including 10mm dia in stirrups, spaces and binder etc complete all as specified.

M&L for form work to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beam and similar works in rough finished flat surface of concrete complete all as specified.

M&L for form work to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete complete all as specified.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished surface of concrete complete all as specified.

M&L for formwork to sides soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surface of concrete all as specified

M&L for reinforced cement concrete M-25 (Design Mix) using 20 mm graded stone aggregate as in foundation including rafts, footing, foundation beams, plinth beams, base of columns and the like complete all as specified.

M&L for reinforced cement concrete M-25 (Design Mix) using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.50 m span and the like complete all as specified.

M&L for reinforced cement concrete M-25 (Design Mix) using 20 mm graded stone aggregate as in columns, pillars, piers, posts, struts and the like complete all as specified.

M&L for reinforced cement concrete (design mix) M-25 grade using 20mm graded aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like concrete all as specified.

M&L for reinforced cement concrete 1:1.5:3 (Nominal Mix) type B-1 using 20 mm graded stone aggregate as in landings, cover slabs for man holes etc, chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and the like complete all as specified.

Demolition of stone slab and tiles laid, bedded and pointed in any mortar of any description or thickness and in any position complete all as specified.

M&L for 18 to 22 mm thick machine cut kota stone slab flooring over 15 mm thick cement screed bed in cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including mirror polishing complete all as specified.

S&F for 18 to 20 mm thick single piece perfect black granite work (table rubbed and polished) in steps, jambs, pillers, window cills, cooking plate forms and like laid over 15 mm thick cement mortar (1:4) incluidng pointing in white cement (1:2) using marble dust with admixure of pigments to match with shade of granite including making hole for gas pipe complete all as specified.

M&L for rounding to exposed edges of stone slabs such as in steps,cooking platform and other similar situations complete all as specified.

Taking up or down steel tubing and connections including cleaning for re-fixing for 15 mm bore complete all as specified.

Taking up or down steel tubing and connections including cleaning for re-fixing for 20 mm bore complete all as specified.

S&F for 20 mm CPVC pipes SDR 11 & Plain CPVC SDR 11 including fittings on walls/ceiling or laying in floors complete all as specified.

S&F for 25 mm CPVC pipes SDR 11 & Plain CPVC SDR 11 including fittings on walls/ceiling or laying in floors complete all as specified.

S&F for brass elbow 25 mm X 15 mm for CPVC pipe 20 mm outer dia complete.

S&F for brass tee for CPVC pipe 20 mm outer dia complete.

S&F for Male Brass Threaded Adaptor (MTA/ MBTA) )

S&F for Female Brass Threaded Adaptor (FTA/ FBTA) for CPVC pipe 20 mm outer dia complete.

S&F in repairs 15 mm dia bib tap chromium plated with fancy type long body with screwed down, screwed for iron pipe complete all as specified.

S&F for 15 mm dia chromium plated stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed for iron pipe with long shank and cup complete all as specified.

S&F in repair chromium plated grating 125 mm dia with or with out hole to match the colour of floor tile complete all as specified.

S&Fin repairs PVC connection 450 mm long with two nuts and washers for 15 mm bore pipe complete all as specified.

Taking down eaves gutters and rainwater pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-necks etc, (measured overall as fixed along the centre line over fittings and accessories complete all as specified.

Dismantling of cast iron or reinforced concrete drain pipes 100/75mm bore of any radius jointed in cement mortar and in any position complete all as specified.

S&F for 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with MS clamps complete all as specified .

S&F for 110 mm bore PVC (SWR) bends any radius complete all as specified.

S&F for 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with MS clamps complete all as specified .

S&F for 75 mm bore PVC (SWR) bends any radius complete all as specified.

S&F in repairs cast iron pipe floor trap long neck type 75 mm dia without greating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F for 75 mm bore cast iron (sand cast) soil, waste and vent pipe in any length with or without ears with lead joint laid in tranches or in floor complete all as specified.

S&F for 100 mm bore cast iron soil (sand cast) soil, waste and vent pipe in any length with or without ears with cement joints in cement sand mortar 1:1 with spun yarn laid in trenches or fixed to walls all as specified.

S&F for 100 mm bore cast iron bend (any radius), diminishing piece or taper (larger bore measured) complete all as specified.

S&F for 75 mm bore cast iron bend (any radius), diminishing piece or taper (larger bore measured) complete all as specified.

S&F for cast iron cowl for 75mm bore pipe.

S&F for 100 mm bore cast iron branch pieces, single (equal or unequal),ordinary or inverted(spigot or socket type)or with parallel branches complete all as specified.

S&F for 75 mm bore cast iron branch pieces, single (equal or unequal),ordinary or inverted(spigot or socket type)or with parallel branches complete all as specified.

S&F for Stack clamps for 75 mm bore pipe out of 50 mm by 5 mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roof complete all as specified.

S&F for Stack clamps for 100 mm bore pipe out of 50 mm by 5 mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roof complete all as specified.

Demolition of cement concrete in ground floors and pavings not exc 15 cm thickness (below or above ground level) and removing debris from site to out side MOD land complete all as specified.

M&L for 75 mm thick cement concrete type C-1, 1:3:6 (using 20 mm graded stone aggregate) as in plinth protection laid in bay not exc 3.00 Sqm each finished even and smooth without using extra cement with and including all necessary form work to divide the area in panels finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm wide joints through out the thickness of plinth protection duly filled with bitumen mastic (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified.

Taking down chowkat or frame with shutter( without taking off shutter from frame) area exc 1.5 Sqm & not exc 4 Sqm each all as specified.

Taking down chowkat or frame with shutter( without taking off shutter from frame) area not exc 1.5 Sqm each all as specified.

S&F in repairs sinks made of stainless steel 1mm thick kitchen or labortory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 485 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified.

S&F in repairs stainless steel plate rack size 36 inch X 31 inch X 10 inch made of 1 mm thick stainless steel sheet complete all as specified.

S&F for aluminium anodised powder coated (minimum thickness of powder coating 50 micron) of approved colour sliding type three track (two glazed shutters and one gauzed shutter) window with sliding shutter and frame with and including aluminium grill comprising the followings: - (i) Frame section 91.85 mm X 31.75 mm X 1.30 mm, Jindal section No. 8758 for top and sides rails and 91.85 mm X 31.75 mm X 1.20 mm for bottom rail, section No. 8687. (ii) Shutter for top, bottom and side rails 40 mm X 18 mm X 1.50 mm, section No. 8820. (iii) Glass 5.00 mm thick one side reflective glass and other side visible fixed with rubber gasket and aluminium clips bearing section No. 4407 and necessary handles, tower bolt etc as directed. (v) Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm (vi) Filling of gap between wall and aluminium frame with silicon putty to make it proper water tight. (vii) Locking arrangement and providing Namda rope to make the frames air tight.

S&F for anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern with approved standard section and fixed to the existing window frame with CP brass screws @ 200 mm centre to centre including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening all complete as per requirement and direction of Engineer-in-charge.

S&F for powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified.

S&F for powder coated (minimum thickness of powder coating 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc complete all as specified.

M&L for for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/ chowkat of size 50 mm x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm², modules of elasticity 900 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (Note : 1. MS hold fast/ lugs or SS dash fasteners shall be measured and paid separately 2. WPC solid door/window frames, minus 5 mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made).

M&L for for factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm², modulus of elasticity 850 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws all as per direction of Engineer-In-Charge. (Note: Butt hinges shall be measured and paid separately)

S&F for 35 mm thick factory made solid panel PVC door shutter wire gauzed wood grain printed PVC sheet used instead of Plain colour PVC sheet & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVCbeading of 10mm x 10mm (900) used instead of exposed portion of PVC sheet beading. wire gauzed i.e. panel will be of wire gauze in lieu of wood grain printed PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly of pvc sheet conforming as per IS-4020 made from MS tube of 19 gauge thickness of size 19 mm x 19 mm style and 15 mm x 15 mm for rail covered with heat moulded PVC channel of 5mm thick and 75mm, 125 mm, 125 mm wide for top rail, lock rail and bottom rail on either side at 5 mm thick 20 mm wide cross PVC sheet of gap inserted for top rail and bottom rail, paneling of 5mm PVC sheet fitted in MS frame welded/sealed to the style at rail with 30 mm wide, 5 mm thick PVC sheet beading sides and jointed together with solvent cement adhesive etc including aluminimum mongry complete all as specified and directed by Engineer-in-Charge.

S&F for 300mm long Mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed.

S&F for 100mm long Mild steel butt hinges, cold rolled, medium weight.

S&F for 125 mm extruded aluminium alloy handles, fabricated type, anodised.

S&F for 150mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed

S&F for mild steel 300 mm ordinary rat tail rod patttern springs includding roller and roller plate complete

S&F for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde-E-165 complete all as specified.

M&L for preparation of newly steel surfaces of any description not otherwise described over 10cm wirdh or girth and applying two coats of synthetic enamel paint (1st quality)over a coat of red oxide zinc chromate primer complete all as specified

S&F for mild steel work as in hold fast for door window frames or chowkat etc, cut to length or drilled hole and fixed with screw etc conforming to Fe-290 Gde-E-165 complete all as specified.

M&L for treating small article such as hold fast area not exc 0.1 Sqm each with black tar or coal tar black paint all as specified.

S&F for stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified.

S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified.

Hacking out old broken glass of any description, from old wooden or steel, concrete or brick surrounds, any thickness or size complete all as specified.

M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in coping and similar works including necessary formwrok all as specified .

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing debris from site to out side MOD land complete all as specified.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified.

M&L fo 25 mm thick cement concrete (1:2:4) type B-O using 12.5 mm graded crushed stone aggregate as in sub base, floor etc surface finished even and fair complete.

S&F for vitrified ceramic tiles 10 mm thick (Square/rectangular) Nano polished single charged (light shade) area of each tile not exceeding 0.36 sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile over and including screed bed or bedding layer of mortar 20 mm thick for laying floor finish (1:6) complete all as specified.

All as per item No. 101 above but on vertical surface such as dado, skirting, wall etc over 10 mm thick rendering in cement mortar 1:4 complete all as specified.

S&F for non skid coloured ceramic tiles 400 mm x 400 mm x 7 to 8mm thick as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement match the surface of tile over 15 mm tnick screed bed in cement mortar 1:6 complete all as specified.

M&L for digital coloured light shade glazed ceramic tiles 300 mm x 600 mm x 8 to 10 mm thick on vertical surface such as skirting, dados and risers to steps etc, set and jointed in neat cement slurry, and pointed in white and coloured cement to match the surface of tile over 10 mm thick rendering in cement mortar 1:4 complete all as specified.

M&L for digital coloured dark shade glazed ceramic tiles 300 mm x 600 mm x 8 to 10 mm thick on vertical surface such as skirting, dado and risers to steps etc, set and jointed in neat cement slurry, and pointed in white and coloured cement to match the surface of tile over 10 mm thick rendering in cement mortar 1:4 complete all as specified.

S&F for false ceiling at height with GRG (Glass fibre Reinforced Gypsum) false ceiling tiles of size 595 mm X 595 mm of approved texture, design and pattterns having moisture content less than 2% humidity resistance of 99%, NRCO.50 to 0.75 as per IS 8825: 1987, noncombustible as per BS 476 (Part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended inter locking metel T-Grid of hot dipped galvanized iron section of 0.33 mm thick (galvanized @ 120 grams per sqm including both side) comprising of main-T runners of size 15X12 mm of length 3000 mm,cross-T of size 15X12 of length 1200 mm and secondary intermidate cross-T of size 15X12 mm of length 600 mm to from grid module of size 600X600 mm suspended from ceiling using Galvanized mild steel items( galvanizing @ 80 grams per Sqm) i,e 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85 mm x25 mm x 2 mm Galvanized iron perimeter wall angle of size 24 mm X 24 mm X 0.40 mm of lenght 3000 mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall good screw complete all as specifed.

M&L for removal to existing treatment from roof including brick tiles laid dry etc any thickness or description complete all as specified .

Demolition of mud in roof any thick including plastering & leeping (whether full thickness removed or only a part there of) and removing debris from site to out side MOD land.

M&L for cement concrete 1:3:6 type-C1 (using 20mm graded stone aggregate) as in roof padding for levelling course complete all as specified.

M&L for water proofing treatment on approachable roof with following specifications : (a) 10mm thick screed bed in CM 1:3 mixed with polymer based water proofing compound when levelling coarse is still green. (b) After the surface is fully dried then applying a coat of bituminous primer @ 0.30 liter/Sqm. (c) After primer the entire roof surface shall be painted with hot blown bitumen grade 85/25 confirming to IS-702 @ 1.2 Kg/Sqm. (d) After bitumen layer, polymeric water proofing membrane consisting of 90 to 100 micron thick central core of HMHDPE film and standard weight 3 Kg/Sqm shall be laid with 100mm side lap/end lap on prepared surfaces as per manufactuer's instruction complete all as specified.

M&L for factory made concrete tiles, machine pressed of size 250 mm X 250 mm X 20 mm to 25 mm thick with gray cement and pigment laid over a bedding layer of 15mm screed in cement mortar 1:3 including joints filled with polymer based cement proof joint filler as per manufacturer specification/instructions and company / brand as approved by GE complete all as specified.

M&L for applying a coat of aluminium paint at 0.20 Kg/Sqm all as per manufacturer's instructions complete all as specified.

M&L for cutting out creck in V-section in existing roof, chajjas or similar work up to 40 mm deep and cleaning the same with water jets to get rid of any loose material and grouting with cement & sand morter 1:3 mixed with liquid WPC all as directed .

M&L for cement concrete type B-1, 1:2:4 (using 20 mm graded stone aggregate) as in roof kerb and the like rounded or chamfered on edges complete all as specified.

E/M PORTION Taking down copper/aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc and making good disturbed surfaces of walls, floors, etc complete all as specified.

Taking down old sub main copper/aluminium cable of size from existing conduit/ batten complete all as specified.

Taking down old MCB/DBs/ main switches complete all as specified.

M&L for point wiring with 1.5 Sqmm FR-LSH PVC insulated unsheathed copper conductor single core multi stranded cable 650/1100 volts grade drawn in and including concealed non-metallic rigid PVC conduit medium grade with all fittings (ISI Marked) not less than 20 mm external dia fixed concealed / recessed on wall/ceiling etc including1.5 Sqmm FR-LSH PVC insulated unsheathed copper conductor single core multi stranded cable 650/1100 volts grade as earth continuity wire including MS sunken pressed steel terminal boxes of suitable size made of sheet 1.6mm thick with 3.0 mm thick bakelite sheet top cover for one light point controlled by one way switch complete all as specified.

All as per item No. 118 above but for One Fan point controlled by one way switch.

All as per item No. 118 above but for One 3 pin socket outlet, 5/6 Amp on independent board.

All as per item No. 118 above but with 2.5 Sqmm FRLSH PVC insulated unsheathed copper conductor single core multi stranded cable 650/1100 volts grade drawn in and including concealed non-metallic rigid PVC conduit medium grade with all fittings (ISI Marked) not less than 20 mm external dia fixed concealed / recessed on wall / ceiling etc including 2.5 Sqmm FRLSH PVC insulated unsheathed copper conductor single core multi stranded cable 650/1100 volts grade as earth continuity wire including MS sunken pressed steel terminal boxes of suitable size, made of sheet 1.6mm thick with 3.0 mm thick bakelite sheet top cover one 3 pin 15 or 16 Amp socket outlet on independent board complete all as specified.

Disconnecting and taking down exhaust fan of any sweep with louvre and M&L for spraying and painting of exhaust fan with synthetic enamel paint including scrapping, filling cavities with filler, refixing exhaust fan and reconnecting electrically with 3 core 23/0.00076 PVC flexible cable from ceiling rose to exhaust fan including testing etc complete all as specified.

S&F for ceiling fan with blades, down rod, electronic regulator and accessories 230 Volt, 1200 mm sweep, min air delivery 210 CFM with service value 6.00 BEE Five star rated with brushless direct current motor (BLDC) complete all as specified.

S&F for wall/surface mounted type LED light fitting batten type complete with LED 1x 20 Watt (4 feet long), extruded aluminium body with heat sink provided for efficient heat dissipation and integrate electronic drive complete with all accessories internally pre-wired and including connecting up with 3 core twisted flexible copper conductor cable complete all as specified. Make : Philips Cat Part No BN 021C LED 20S PSU CW GR S2 / Havells Cat Part No : ENDURA LINEAR NEO BS 20W LED 865 SPC WH or equivalent make of Wipro.

S&F for exhaust fan of 450 mm sweep metalic body (Heavy duty) single phase 230/240 volts, AC, 900 RPM and making holes with lovoured shutters including mounting frame and connecting the fan to ceiling rose including provision of three core flexible copper conductor cable of size 1.5 Sqmm copper including to inside out surface & white wash etc with not less than 0.5mtr long to connection complete as specified.

S&F for ceiling rose, surface bakelite 65 mm x 50mm, three terminals all as specified.

S&F for sub main wiring with 1100 volts grade heavy duty two single core 4 Sqmm size (nominal area) PVC insulated (FRLS) copper multi-stranded conductor cable drawn into & including PVC conduit medium grade not less than 25 mm dia including all accessories & fittings fixed concealed with and including chase cutting and making good the same as per existing specifications along with a continuous run of 4 Sqmm size (nominal size) stranded copper conductor PVC insulated (FRLS) (green colour) cable as earth wire complete all as specified. (NOTE: - TWO SINGLE CORE CABLES ALONG WITH ONE EARTH WIRE AND PVC CONDUIT SHALL BE MEASURED AS ONE UNIT LENGTH).

S&F for sub main wiring with 1100 volts grade heavy duty two single core 6 Sqmm size (nominal area) PVC insulated (FRLS) copper multi-stranded conductor cable drawn into & including PVC conduit medium grade not less than 25 mm dia including all accessories & fittings fixed concealed with and including chase cutting and making good the same as per existing specifications along with a continuous run of 6 Sqmm size (nominal size) stranded copper conductor PVC insulated (FRLS) (green colour) cable as earth wire complete all as specified. (NOTE: - TWO SINGLE CORE CABLES ALONG WITH ONE EARTH WIRE AND PVC CONDUIT SHALL BE MEASURED AS ONE UNIT LENGTH).

S&F for flush mounting factory made Ekinoxe SPN DB's Double door, IP-43 Protection, IK-09 with metal door, with neutral bar, Earth bar and cables ties for cable management fully insulated bus bar 8 way with 200 amp rated bus bar complete all as specified.

S&F for MCB SPN (single pole and neutral) 240 volts 40 Amp, breaking capacity 10 KA, ‘C’ Series etc complete all as specified.

S&F for MCB SP (single pole) 240 volts, 6 to 32 Amp, 50HZ, 10 KA, ‘C’ series complete all as specified.

S&F for switch piano flush type single pole one way 5/6 Amp complete all as specified.

S&F for socket outlet 2 in 1, 3 pin, 5/6 & 15/16 Amp flush type complete all as specified.

S&F for socket outlet 2 in 1, 3 pin, 5/6 Amp flush type complete all as specified.

S&F for switch piano flush type single pole one way, 15/16 Amp complete all as specified..

S&F for rotary type electronic fan regulator 5 Step AC, 230V, Single phase complete all as specified.

M&L for earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to earth lead wire of GI wire 4 mm dia by means of nuts/bolts and washers, check nuts of galvanized iron or steel including 15 mm dia GI pipe light grade upto 1.5 mtr below GL for protection pipe, excavation and earth work charcoal dust, common salt, cement concrete 1:3:6 type C-1 chamber with cover and RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with 6mm dia round bars @ 75 mm c/c both way with MS handle 12 mm dia PGI funnel and wire mesh all as shown in electrical plate No. 5 of SSR Part-I connected to ear thing test point all as specified or indicated including testing on completion all as directed by Engr-in-Charge.

Ikrar khan & co. (BID ID -3166778)

M/s M Aali construction co (BID ID -3174185)

M/s Agarwal Builders (BID ID -3173306)

Jain construction co (BID ID -3167680)