wellness- Health and wellness centre pattom ward in tvm corporation E14/193498/24

Amount

maintance work

21.2.2:Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides

2.28.1:Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.All kinds of soil

13.60.1:Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

OD44216/2024-2025:Engaging man coolies

OD44217/2024-2025:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.35 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side. of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 metre or as desired by Engineer-in-charge. The sheet shall (51.20) be fixed using self drilling/self tapping screws ofsize (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical orcurved surfaces, excluding the cost of purlins, rafters and trusses and including cutting tosize and shape wherever required. Material M MR Precoated galvanised iron profile sheet 0.35mm TCT (MR1269) sqm 233.65000 367.00 85749.55 M1 1023 Galvanised steel J or L hooks 8 mm dia 10 nos 476.00000 120.00 5712.00 M2 1208 Bitumen washer 100 nos 476.00000 30.00 142.80 M3 1209 G.I. Plain washer thick 100 nos 476.00000 35.00 166.60 M4 Carriage C EST No. :LSGD/CELSGD/EST/826/2022_5_4_3/RE 1 (Edit Id : 1) (Dsor year : 2018,Cost Index (Place : Ernakulam,Value : 135.59),GST : 18% Printed On 2023-05-15 14:28:10.081 17 SOR/Spec Code MR code Description/Remarks Unit Quantity Rate Amount Label 9977 Carriage L.S 8.06000 2.00 16.12 C1 Labour L 0130 Mistry Day 2.34000 738.00 1726.92 L1 0112 Carpenter 2nd class Day 9.34000 679.00 6341.86 L2 0114 Beldar Day 9.34000 558.00 5211.72 L3 Tools&Plants(Hire charges) T 9999 Sundries L.S 39.52000 2.00 79.04 T1 Total 216.140 sqm 105146.61 Unit Total 1.000 sqm 486.47 Add Water Charge 486.47 @1.00% 4.86 Total 491.33 Add Contractors Profit & Overhead 491.33 @15.00% 73.70 Total 565.03 Add Cost Index 104.24 @35.59% 37.10 Total 602.13 Add Tender Variation 141.34 @-16.84% -23.80 Total 578.33 GRAND TOTAL sqm 578.33

50.10.1:Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.3.1:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

17.7.1:Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

ARUNLAL C

PRADEEP.T

Thampi

Bidder Name

Shajudeen

Thampi

ARUNLAL C

PRADEEP.T