Construction of Addition Accommodation of ITI building Bagsaid in Tehseil Thunag Distt Mandi SH Construction of building portion in 2nd floor with WS and SI

Amount

Providing form work with steel plates 3.15mm. (Three point fifteen millimetre ) thick welded with angle iron in frame 30x30x5mm. (Thirty x thirty x five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to all floor level and removal of same for insitu reinforced concrete and plain concrete work as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . Columns, pillars, posts and struts in square, rectangular or polygonal in plan.

Beams, cantilevers, girders and lintels, sides and soffits of beams, beam hunching, cantilevers, bressumers and lintels upto 1 mtr. depth.

Flat surfaces such as soffits of suspended floors, roofs ,landings and the like, floor etc. upto any thickness.

Stair cases with slopping or steped soffits excluding landing.

Edges of slabs and breaks in floors and walls in any width.

Providing and laying cement concrete 1:1.5:3 (One cement: One and half sand :three graded/crushed stone aggregate 20mm. (Twenty millimetre ) nominal size) mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced concrete work upto all floor level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . Columns, pillars, posts and struts etc. floor any level

Suspended floors , roofs, landing and shelves and their supports, balconies, beams , girders, bressumers and cantilever upto floor any level.

d) Stair cases (except spiral stair case) excluding landing but including preparing of the surface and finishing of nosing upto all floor level.

Providing tor steel reinforcement for R.C.C. work including bending, binding and placing in position including cost of binding wire complete upto floor all level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Precast concrete block masonry in partition walls 10 cm.(ten centimetre) thick with solid block of approved size including quion blocks, jamb blocks, closer etc. made of cement concrete 1:3:6 (1 cement:3 sand:6 graded stone aggregate 40mm and down gauge) in Cement Mortar 1:6 upto floor any level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Precast concrete block masonry (including quion blocks,jamb blocks, closer etc.) with solid concrete blocks of approved size made of cement concrete 1:3:6 (1 cement:3 sand:6 graded stone aggregate 40mm (forty millimetre) and down gauge) foundation and plinth in Cement Mortar 1:6 upto floor any level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing wood work in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position 1st class Deodar wood as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing factory made PVC door frame single rebate of any clours of size 50x47mm (fifty into forty seven millimetre) with a wall thickness of 5mm (five millimetre) made out of extruded 5mm (five millimetre) rigid PVC foam sheet heat bend & mitred at corners and jointed with 2 Nos. of 150mm (One hundred fifty millimetre) long brackets of 15mmx15mm (fifteen millimetre into fifteen millimetre) M.S. square tube, the vertical door profiles to be reinforced with 19mmx19mm (nineteen millimetre into nineteen millimetre) M.S. square tube of 19 gauge EPDM rubber gasket weather seal to be provided throughout the frame i/c fixing of door frame to wall with M.S. screws 100long with wooden or rawl plugs emedded in masonry complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing angle iron cupboard frames frames manufactured from M.S.Angle iron section 25X25X5mm (twenty five into twenty five into five millimetre) thickness including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 25X25 mm (twenty five into twenty five millimetre) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm (two point five millimetre) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing 40x3 mm (forty into three millimetre) flat iron hold fast 40cm (forty centimetre) Long including fixing to frame with 10mm (ten millimetre) diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm (thirty into ten into fifteen centimetre) 1:3:6 ( 1 cement : 3 sand: 6 graded stone aggregate 20mm (twenty millimetre) nominal size) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing 0.60mm (zero point sixty millimetre) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing ridges or hips 60 cm (sixty centimetre) overall with 0.60mm (zero point sixty millimetre) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charges.

Providing and fixing valley 60 cm (sixty centimetre) overall 0.60mm (zero point sixty millimetre) thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-charge

Providing and fixing on wall face 100mm (One hundred milimetre) dia PVC(D-Plast) rain water pipes of working pressure not less than 4.5 Kg/sqm(Four point five kilogram per square metre) including filing the joint with approved adhersive complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing PVC plain bend 100 mm (one hundred millimetre) dia on wall face (D-Plast) accessories for rain water pipes including filling the joint with approved adhesive complete as per the direction of Engineer-in-Charge of materials within all leads, lifts and other incidentals.

Steel work welded in built up sections, trusses and framed work,including cutting, hoisting fixing in positiobn and applying a priming coat of red lead paint as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals in: Trusses and trussed purlins in buildings including carriage of materials with in all leads,lifts and other incidentals.

In beams joists channels ,angles , tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing M.S.round holding down or anchor bolts with nuts and washer plates complete as per the direction of Engineer-in-Charge of materials within all leads, lifts and other incidentals.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm (one point sixty six millimetre to two millimetre) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete (Base members of steel work shall be measured & paid separtely) as per the direction of Engineer-in-Charge of materials within all leads, lifts and other incidentals.

Providing and fixing flush door shutters core of black board construction with frame of first class hard wood and well matched firtst class Indian teak ply veneering with vertical grains of cross band and face vaneers on one face and commercial ply veneering with vertical grains of cross band on other face of shutters 40 mm (forty millimetre) thick including black enamelled M.S. butt hinges as per the direction of Engineer-in-Charge of materials within all leads, lifts and other incidentals.

Providing and fixing fully double glazed (double glass) shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws 40 mm (forty millimetre) thick 2nd class deodar wood as per the direction of Engineer-in-Charge of materials within all leads, lifts and other incidentals.

Providing and fixing double glazed (double glass)fixed in wooden, window ventilator shutters and partition etc. with wooden corner or wooden bead in teak wood bead etc. of specified size with nails mitred and jointing complete and glazing with glass panes of 4mm (four millimetre) thickness (weight not less than 10.00 kg/sqm) as per the direction of Engineer-in-Charge of materials within all leads, lifts and other incidentals.

Providing and fixing to existing door frames, 30mm (thirty millimetre) thick factory made PVC panelled door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x19mm (nineteen millimetre into nineteen millimetre) for styles and 15mmx15mm (fifteen millimetre into fifteen millimetre) for top & bottom rails, M.S. frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm thick heat moulded PVC "C" channel of size 30mm (thirty millimetre) thickness, 70mm (seventy millimetre) width out of which 50mm (fifty millimetre) shall be flat and 20mm (twenty millimetre) shall be tappred in 45 degree angle on either side forming style and 5mm (five millimetre) thick, 95mm (ninety five millimetre) wide, PVC sheet out of which 75mm (seventy five millimetre) shall be flat and 20mm (twenty millimetre) shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm (one hundred fifteen millimetre) wide PVC sheet out of which 75mm (seventy five millimetre) shall be flat and 20mm (twenty millimetre) shall be tapered on both side to form lock rail, top, bottom and lock rail shall be provided either side of the panel 10mm (ten millimetre) thick, 20mm (twenty millimetre) wide cross PVC sheet be provided as gap insert for top rail and bottom rail paneling of 5mm (five millimetre) thick both side PVC Sheet to be fitted in the M.S. frame welded/sealed to the style & rails, joints mitred and jointed with solvent cement adhesive i/c fixing of PVC shutter with existing frame with M.S. butt hinges 100x50x1.90mm (hundred into fifty into one point ninety millimetre) size with necessary screws etc complete as per the direction of Engineer-in-Charge of materials within all leads, lifts and other incidentals.

Providing and fixing 19mm thick Commercial Board water proof shutters for cup boards i/c fixing with nickel plated piano hinges with screws etc complete) as per the direction of Engineer-in-Charge of materials within all leads, lifts and other incidentals.

Providing and fixing 19mm (nineteen millimetre) thick water proof commercial board in shelves/box for cup board with butt joints & fixing with nails & screws etc complete) as per the direction of Engineer-in-Charge of materials within all leads, lifts and other incidentals.

Providing and fixing 2nd class deodar wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm (zero point fifty six millimetre) for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screw etc complete as per specification and as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing wall panelling 12 mm (twelve millimetre) thick prelaminated board one side of approved brand fixed on wooden frame 4x4 cm (four into four centimetre) frames on spacing of 60 cm x 60 cm (sixty centimetre into sixty centimetre) c/c fixing with rawl plugs on wooden pegs screwed etc and 1mm depp grooves of required pattern in elevation and finished teak wood beading out of 25 x 12 (twenty five into twelve) and 75 x 60 mm (seventy five into sixty millimetre) cornivce of different pattern to top and cornice jpoints including polishing and painting as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing M.S. plain grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals. 300x16mm (three hundred x sixteen millimetre)

250x16mm (two hundred fifty x sixteen millimetre)

Providing and fixing aluminium tower bolts (berrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals. 300x10 mm (three hundred into ten millimetre)

250x10 (two hundred fifty into ten millimetre)

200x10mm (two hundred into ten millimetre)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals. 125mm (one hundred twenty five millimetre)

100mm (One hundred millimetre)

Providing and fixing 150 mm (one hundred fifty millimetre) bright finished hard drawn hooks and eyes as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 150 mm (one hundred fifty millimetre) oxidized M.S. single acting spring hinges with necessary screws etc. complete as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 150 mm (one hundred fifty millimetre) oxidized M.S. double acting spring hinges with necessary screws as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodized aluminium fan light pivot with necessary screws as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodized aluminium fan light catch with necessary screws complete as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 90 mm (ninety millimetre) oxidized M.S. hasps and stapples (safety type) with necessary screws etc. complete as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 1st class deodar wood 75 mm x 60mm (seventy five millimetre into sixty millimetre) rounded hand rails in straight length complete as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/concrete/stone wall for interior plastering including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:6 sand) above floor all level as per the direction of Engineer-in-Charge including carriage of materials within all leads, and lifts other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering including arises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:six sand as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

6mm (Six millimeter) cement plaster to ceiling in cement mortar 1:3 (one Cement : three Sand) as per the directions of Engineer-in-Charge including carriage of materials within all leads, lifts and other ncidentals.

Kota stone slab flooring 20 mm (twenty millimetre) (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. including rubbing and polishing complete 25 mm (twenty five millimetre) thick upto floor all level as per the directions of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Kota stone slab 25 mm (twenty five millimetre) thick in risers of steps,skirting dado and pillars laid on 12 mm (twelve millimetre) (average) thick cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and laying marble work (Table rubbed and polished) in flooring 20mm(twenty millimetre) thick base in cement mortar 1:3(1cement:3sand) including jointing with cement mortar 1:2(1 white cement:2 marble dust) with an admixure of pigment to match the shade of the marble. 20 mm thick White makrana marble upto floor all level as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

38 mm (thirty eight millimetre) thick parquet ( wood block) flooring of 1st class indian teak wood laid over 25 mm (twenty five millimetre) thick levelling layer of cement concreate 1:2:4 (1 cement : 2 sand :4 stone aggregate 10 mm (ten millimetre) nominal size)( to be paid separately) coated with thin layer of hot bitumen (blown-type) @ 2.45 kg. per sq m. including fixing blocks in position after dipping in hot bitumen ( blown type) upto half depth, planed, levelled smooth and finished complete upto floor all level as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and laying spartic ceremic tiles 5.5mm (five point five millimetre) thick 300 x300mm (three hundred into three hundred millimetre) size in skirting riser of steps laid on a bed of 12mm (twelve millimetre) thick cement mortar 1:3(1cement: 3 sand) finished with flush pointing in white cement as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces(two coats)to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered material as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper prime as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete With ready mixed priming paint brushing red lead,Red-oxide/zinc oxide chrome as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Painting two costs (excluding priming coat on new steel and other metal surfaces with enamel paint brushin to give an even shade including cleaning the surface of all dirt,dust and other foregin matters Enamel paint other than white as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

White washing with lime on undecorated wall surfaces two coats to give an even shade including throughly brooming the surface to remove all dirt dust mortar dirt and other foreign matter as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting Readymixed paint brushing wood primer pink as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Painting two coats(excluding priming coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping With enamel paint other than white as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Polishing two coats with french polish on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt,dust,and sand papered smooth and including a coat of wood filler as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing 1000 litres PVC water storage tank of ISI : 12701 marked,G.I. inlet and outlet connection and 15mm (fifteen millimetre) dia brass ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 20 mm nominal bore to wall ceiling and floor galvanized mild steel tube (medium grade) tube fittings and clamps including making good the wall ceiling and floors

Providing and fixing plytheline - Aluminium polyethylene (PE-AL-PE) composite pressure pipe U.V. stabilized with carbon black confirming to IS-15450-2004 water supply including clamps at one metre spacing, cutting, fixing and making good the wall etc. but excluding the cost of fittings (internal work) pipe exposed on wall internal as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 1620 (20 mm O.D. pipe)

1216 (16mm O.D. pipe)

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors,couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. (KITEC make) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. Equal Tees 1216

Equal Tees 1620

Reducing Tees 1620

Reducing Tees 2025

Female Elbow 1216 X 15 mm (one thousand two hundred sixteen into fifteen millimetre) thread

Female Elbow 1620 X 15 mm (one thousand six hundred twenty into fifteen millimetre) thread.

Female Elbow 1620 x 20 mm (one thousand six hundred twenty into twenty millimetre) thread

Female Elbow 2025 x 25 mm (two thousand twenty five into twenty five millimetre) thread.

Female thread connector 1216 X 15 mm (one thousand two hundred sixteen into fifteen millimetre) thread

Female thread connector 1620 x 20 mm (one thousand six hundred twenty into twenty millimetre) thread

Male thread connector 1216 X 15 mm (one thousand two hundred sixteen into fifteen millimetre) thread

Male thread connector 1620 x 20 mm (one thousand six hundred twenty into twenty millimetre) thread

Couplers 1216

Couplers 1620

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 75 mm (seventy five millimetre) nominal size.

110mm (one hundred ten millimetre) nominal size.

Providing and fixing 110mm (one hundred ten millimetre) nominal size PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete icluding fixing with approved adhesives etc. as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PVC single equal branch plain, ISI marked including fixing with approved adhesives etc as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 75 mm (seventy five millimetre) nominal size.

110mm (one hundred ten millimetre) nominal size.

Providing and fixing PVC collar, ISI marked including fixing with approved adhesives etc. as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 75 mm (seventy five millimetre) nominal size.

110mm (one hundred ten millimetre) nominal size.

Providing and fixing PVC plain bend, ISI marked including fixing with approved adhesives etc. as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 75 mm (seventy five millimetre) nominal size.

110mm (one hundred ten millimetre) nominal size.

Providing and fixing PVC cowel etc. as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 75 mm (seventy five millimetre) nominal size.

110mm (one hundred ten millimetre) nominal size.

Providing and fixing PVC clamps, ISI marked of approved design with steel screws and rawal plugs etc. Complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 75 mm (seventy five millimetre) nominal size.

110mm (one hundred ten millimetre) nominal size.

Providing and fixing 110 mm x 75 mm (one hundred ten millimetre into seventy five millimetre) size PVC floor trap ISI marked of self cleansing design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Flat back 550mm x 400 mm (five hundred fifty millimetre into four hundred millimetre) vitreous china wash basin with pair of hole for pillar tap with C.I or M.S brackets painted white including cutting holes and making good the same but excluding fitting :- extra for pair of holes for pillar tap instead of single hole (Jaquar or ESS-ESS) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing vitreous China wash down, water closet squatting pan (Indian type W.C pan) size 580mm (five hundred eighty millimetre) (Earth work, bed concrete, foot rest and trap to be measured and paid for separately). Orissa pattern (Cera) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

P/F PTMT coloured/white high density polyethylene/poly propylene 10 litres (ten) capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm (fifteen millimetre) nominal size PVC ball valve with polythene float,with push button, couplings for connections with inlet,outlet and overflow pipe, 40mm dia C.P.flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (over flow pipe to be measured and paid for seprately) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing vitreous china pedestal for wash basin complete recessed at the back for reception of pipes and fittings with in all leads, lifts and other incidentals as per the direction of Engineer-in-charge.

Providing and fixing 32mm (thirty two millimetre) dia C.P Brass waste for wash basin or sink with in all leads, lifts and other incidentals as per the direction of Engineer-in-charge.

Providing and fixing white viterous china flat back or wall corner type lipped front urinal basin of 430x260x350mm (four hundred thirty into two hundred sixty into three hundred fifty millimetre) and 340x430x265mm (three hundred forty into four hundred thirty into two hundred sixty five millimetre) size, respectively with automatic flushing cistern with fitting R.S or C.I brackets standard size galvanised steel flush pipe and spreaders galvanised steel flush pipe and spreaders with brass unions and G.I clamps complete including painting of cistern and fittings, cutting and making good the walls, floors where required one urinal basin with 5 liters C.I automatic flushing cistern with in all leads, lifts and other incidentals as per the direction of Engineer-in-charge.

Providing and fixing 32mm (thirty two millimetre) dia MI union for wash basin or sink with in all leads, lifts and other incidentals as per the direction of Engineer-in-charge.

Providing and fixing division plate for urinals 600mm x300mm (six hundred millimetre into three hundred millimetre) virterous china with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) nominal bore C.P. brass flush pipe/spreaders for urinal with fittings such as unions, clamps etc. (all C.P.) including cutting holes and making good the same with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing chromium plated brass soap dish with C.P brass brackets fixed to wooden cleats with C.P brass screws with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) dia C.P stop cock with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) dia C.P brass bib tap with capstan head with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) dia C.P brass pillar tap with capstan head with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) C.P.Brass angle valve without nuts and pipe with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 300/450mm length 15mm (fifteen millimetre) nominal bore P.V.C connection pipe with brass unions with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 100 mm (one hundred millimetre) nominal dia PTMT grating round of approved quality and colour with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 600mm x450mm (six hundred millimetre into four hundred fifty millimetre) beveled edge mirror of superior glass mounted on 6mm (six millimetre) thick A.C sheet or ply wood sheet and fixed to wooden plugs with C.P brass screws and washers with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing C.,P brass towel rail complete with C.P brass brackets fixed to wooden plugs with C.P brass screws etc. with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 32mm (thirty two millimetre) lead waste pipe for wash basin or sink including check nut with in all leads and lifts and as per the direction of Engineer-in-Charge.

Constructing manhole with R.C.C top slab in 1:2:4 (1 cement :2 sand :4 graded stone aggregate 20mm (twenty millimetre) nominal size) foundation concrete 1:4:8 (I cement :4 sand : 8 Graded stone aggregate 40mm (forty millimetre) nominal size ) inside plastering 15 mm (fifteen millimetre) thick with cement mortar 1:3(1 cement : 3 sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(1 cement :2 sand :4 graded stone aggregate 20mm (twenty millimetre) nominal size)finished smooth complete including curing and testing (i)inside size 800mmx800mm and 500 mm (eight hundred millimetre into eight hundred millimetre and five hundred millimetre) deep including C.I. cover with frame( light duty single (seal ) pattern I) 450mmx610mm (four hundred fifty millimetre into six hundred ten millimetre) internal dimensions total weight of cover and frame to be not less than 38 kg (thirty eight kilogram) (weight of cover 23 kg (twenty three kilogram) and weight of frame 15 kg (fifteen kilogram) with 300 mm (three hundred millimetre) thick walls of squared rubble masonry coursed with hard stone of approval in cement mortar 1:3 (1cement :3sand ) with in all leads and lifts and as per the direction of Engineer-in-Charge.

MED RAM