Construction of dhobeghat parking remain and Residency toilet work near mussorie fall road at nagar palika mussorie

Site clearance including all labour and T&P Depth L.S

2.6 Earth work in excavation by mechnical mean (Hydraulic excavator) manul means over ares (exceedind 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed 2.6.1 All kind of soil

4.1 Providing and laying in possition cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :4.1.8 1:4:8 (1 cement : 4 coarse sand (zone-III) :8 graded stone aggregate 40mm nominal size)

5.15 Providing, hoisting and fixing above plinth level up to floor five level precastreinforced cement concrete in lintels, beams and bressumers, including setting in cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering and shuttering but, excluding the cost of reinforcement, with 1:1:2 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers

12.41 Providing and fixing on wall faceunplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Sigle socketed pipes (weepholes)

5.22 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more

6.4 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in super structure above plinth level up to floor V level in all shapes and sizes in : 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand)

12 mm cement plaster of mix in 1:6 (1 cement : 6 fine sand) (13.1.2) DSR-

2-1 Cement plum Mosonry with 40% plum & 60% 1:3:6 cement concrete including supply of all material, labour, T&P etc. required for proper completion of the work as per drawings and technical specification Clause 802, 803, 1202 & 1203 of MORD Specification ( with 12 % G.S.T. Rate including) (4344.40*.12=521.33=(4344.40+521.32=4865.73)

10.25 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a primer coat of approved steel primer using structural steel etc. as required. 10.25.2 in gratings, frames, guard bar, ladder, railling, brackets, gatesand similar works.

9.1 Providing wood work in frame of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs ordash fastener shall be paid for separately). 9.1.2 sal wood

9.20 Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains of cross bands and face veneers on both faces of shutters 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

11.41 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complete 11.41.3 size of Tile 800X800 mm

13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

13.41 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer

13.61 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 13.61.1 Two or more coats on new work

13.48 Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications :13.48.3 Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr /10 sqm of approved brand and manufacture

4.1 Providing and laying in possition cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :4.1.3 1:2:4 (1 cement : 2 coarse sand (zone-III) :4 graded stone aggregate 20mm nominal size)

4.11 Providing and laying C.C. floor 50 mm thick with cement concrete 1:2:4 ( 1 cement : 2 coarse sand (zone - III) : 4 graded stone aggregate 20 mm nominal size

16.70 Providing and fixing G.I. chain linkfabric fencing of required with in mesh size 50X50 mm including strengtheninh with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. 16.70.5 Made of G.I. wire of dia. 4 mm, PVC coared to achieve outer dia not less than 5 mm in required colour and shade

SANITARY FITTINGS 17.2 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle level), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : 17.2.1 W.C. pan with ISI marked white solid plastic seat and lid

17.7 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar tape, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : 17.7.2 White Viterous China Wash Basin size 630X450 mm with a single 15 mm C.P. brass pillar tap

Providing & Fixing of 15 mm G.I. class 'B' Pipe (Jindal hissar Make) complete with G.I fitting & clamps including supply of all materials, labour and T&P etc. and including making good the wall etc. (internal work) as per D.S.R. code no. 18.12.1 15 mm dia nominal bore

18.12.2 20 mm dia nominal bore

18.48 Providing and placing on terrace ( at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fitting and the base support for tank.

18.18 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :18.18.2.20 mm nominal bore

18.16 Providing and fixing brass stop cock of approved quality 18.16.2 20 mm nominal bore

18.21 providing and fixing uplasticised PVC connection pipe with brass unions : 18.21.2 45 cm length 18.21.2.1 15 mm nominal bore

18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to IS :8931 :18.49.1 15 mm nominal bore

18.53 Providing and fixing C.P. brass angle valve for basin mixer and geyserpoints of approved quality conforming to IS:893118.53.1 15 mm nominal bore

18.37 Constructing masonry Chamber 60X45X50 cm inside, in brick workin cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400X200X200 mm (inside) with locking arragement and RCC top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standerd design : 18.37.1 with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

17.31 Providing and fixing 600X450 mm beveled edge mirror of superior glass ( of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

8.1 Marble work gang saw cut (polished and machine cut) of thickness 18 mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement :3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately & 8.1.1 Raj Nagar Plain White Marble/Udaipur Green Marble?zebra Black Marble. 8.1.1.1 Area of slab upto 0.50 sqm

ITEM DRAINAGE 12.41 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming ti IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 12.41.1.1 75 mm diameter

12.41 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Sigle socketed pipes 12.41.2 110 mm diameter

ITEM ELECTRICAL FITTINGS Wiring point for light with 1.50 sq. mm PVC insulated single core cable in HD PVC conduct pipe on surface complete with 1.50 sq. mm PVC insulated Aluminium conductor cable as earth continuity wire drawn inside the conduit complete in all respect. (M.R) Light. Rate

Tube Light / Led Light

Fan with Box Rate / Exest Fan

Plug Point Box

MCB Box

C S RAWAT

RADHEY SHAYAM SHARMA