Providing & Erecting 2 nos. 16 Mtr. Highmast Towers at Sarigam Three Roads &Sarigam Main Market- Bhandarwada Three Roads, Sarigam, Dist.Valsad

Name Of Providing & Erecting 2 nos. 16 Mtr. Highmast Towers at Sarigam Three Roads

Work :- &Sarigam Main Market-Bhandarwada Three Roads, Sarigam, Dist.Valsad

Qty. Unit with 1% words Amount

20 Mtr 1 Supplying and erecting Flexible PVC 46 46.46 #NAME?

insulated multi strand multi core 1.1 kv grade

ISI marked copper wires of following size to

be erected as directed.(e) 1.50 Sq.mm 3 core

round PVC sheathed

20 Nos 2 Supplying and erecting LED street light / Flood 10711 10818.11 #NAME?

light fittings with High power White LEDs

wattage of 3 Watt and above assembled on

single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast

aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with

diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name

engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT

3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED

driver efficiency > 85 %.( fittings required LM-

79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge

may select any wattage capacity between the

ranges shown.) (B) Flood Light (IP-65), Surge

protection -4KV integral and ,Light must have

440VAC line supply with over-voltage

protection. (vii) 250 watts Cat-lll Make;

Jaquar,Wipro,Havell's,Crompton,Bajaj)

2 Nos 3 providing and erecting Approved make Four 6112 6173.12 #NAME?

pole moulded case circuit breaker having

breaking capacity ICU of 25 KA. at

V,having normal current rating up to 25 A to

100A. with Fixed thermal & magnetic release

suitable to work on A.C. supply 50 c/s. with all

internal connections, spreader tinned copper

& complete erected in existing 16 G.M.S.

housing.ICS=100% of ICU only.Cat III

20 Nos 4 providing and erecting Miniature circuit 268 270.68 #NAME?

breaker single pole 0.5A to 2A system and

having breaking capacity 10 KA to be

erected in existing box. confirming to IS

8828/1996 with ISI Mark Cat.III

16 Kg 5 Providing and erecting HOT deep Galvanised 77 77.77 #NAME?

iron strip wire 8 to 16 SWG.

2 Nos 6 Providing and erecting Pipe type earthing 815 823.15 #NAME?

with 40 mm dia 2.5 mtr long 'B' grade G.I.

pipe with necessary coupling buch buried in

specially prepared earth pit & G.I. earth wire

of 8 SWG erected & connected as directed

2 Nos 7 For using salt and charcoal / coke as required 170 171.70 #NAME?

for pipe type earthing.

Qty. Unit with 1% words Amount

2 Nos 8 Supplying & erecting earth pit of minimum bore 4546 4591.46 #NAME?

dia.150mm size approved make Earthing

Electrode consisting Pipe-in-Pipe Technology as

per IS 3043-1987 made of corrosion free hot

dipped G.I.Pipes having Outer pipe dia of 50mm

having 80-200 Micron galvanising, Inner pipe dia

of 25 mm having 200-250 Micron galvanising,

connection terminal dia of 12mm with constant

ohmic value surrounded by highly conductive

compound with high charge dissipation suitable

for following type of applications with chamber

and heavy duty cover.(approved make OEM has

to submit test certificate) & having back filling

compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 / meter testing as

per IEC 62561-2017, Voltage drop:- < 1 volt at no

load & dry form, Sulphar content:- <2%(C) Back

fill Compound :- Earthing compound should be

capable to retain moisture for long time

Necessary test report must be submitted. (a) For

Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr Back filling compound -

Nos Bag of 15 Kg.

210 Mtr 9 Providing and erecting XLPE (IS:7098)(I)-88 152 153.52 #NAME?

ISI armoured cable multistrand Aluminium

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe

of following size of cables (A) 4 core 16 Sq.

mm Make-Polycab,KEI,RR

kabel,Finolex,Havell's)

150 Mtr 10 Making trench in Hard Murrum / Tar Road of 74 74.74 #NAME?

suitable width of 90 cm or required depth for

laying any size of cable or locating the fault

all over the run and back filling the same and

making the surface as normal ground.

60 Mtr 11 Making trench in Hard Murrum / Tar Road of 354 357.54 #NAME?

suitable width of 90 cm or required depth for

laying any size of cable or locating the fault

all over the run and back filling the same and

making the surface as normal ground. (B) If

additional machinery like hammer driller or

60 Mtr 12 Supplying following size of Light duty “A” 298 300.98 #NAME?

Class G.I . Pipe & erecting as directed by

Engineer-in-charge. (B) 50 mm dia

150 Mtr 13 Providing & laying approved make Double 62 62.62 #NAME?

walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with

necessary connecting accessories of same

material at required depth in existing trench

for laying of cable. below ground / road

surface for enclosing cable (A)50 mm outer

4 Nos 14 Providing and, fixing heavy duty flange type 47 47.47 #NAME?

brass cable gland with rubber ring for PVC

insulated armoured cable complete with out

going tails, insulating tape etc for following

size of cables. (D) 2 to 4 core 16 Sq. mm

16 Nos 15 Solder less crimping type Aluminium lugs 15 15.15 #NAME?

conforming to IS suitable for cable of

following size evenly crimped with high

pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts

in an approved manner. (C) 16/25 Sq.mm.

Qty. Unit with 1% words Amount

2 Nos 16 Supplying, erecting, testing, commissioning approved 182612 184438.12 #NAME?

make M.S. Polygonal High Mast Pole having following

general Specification. (a) Polygonal Section fabricated

from M.S. Plate confirms BSEN 10025 & Hot deep

galvanized minimum 65/86 micron (as per IS

/1985) Lantern carriage with ring and rubber lines for

erection of luminaries of suitable site.(b) Maximum

telescopic section not more than four(c) Double drum

gear pipe motorized winch with 6mm dia S.S. Rod (For

16 mtr and above size) (d) Approved make L.E.D.

aviation light = 1 No. Lightening arrestor = 1 No. with

necessary wiring of 2.5 sq.mm 5 core ISI copper cable

Unarmoured.(e) Bottom most section suitable for

mounting reversible motor and switchgears having door

not more than 1400mm x 300mm with waterproof

gasket & hinges & locking arrangement.(f) Pole

structure comprises suitable size of reversible motor,

cable and necessary switchgears with control panel. (g)

bottom section shall have suitable size of thickness

supports ribs foundation bolts nuts etc.(h) Item not

comprises the cost of lanterns. (i) Necessary Cement

Concrete foundation as per IS including testing &

commissioning of the entire structure for following size

of High Mast poles [4] High Mast 16 Mtr. TOP A/F

Mm, BOTTOM A/F 400 Mm, No. of Sec. No. -

Bottom Thickness - 4 mm, Top Sec. - 3 mm, Size

Base Plate - dia.630 mm x 20 mm thick, Foundation

Bolt Size M24 x 870 mm, Qty - 12 Nos., Suitable for

mounting Fitting of Light - 10 Nos.

Qty. Unit with 1% words Amount

2 Nos 17 Supplying & erecting IP 55 grade following 3560 3595.60 #NAME?

size section pillar fabricated from joint less

M.S. Sheet with angle iron legs made from

jointless M.S. Angle with cable clamps to be

buried in ground to have appropriate erection

to work uniform until erected with cement

concrete foundation and 45 cm high bricks

work finishing with plaster etc. hinged double

door internally supported on both side, with

internal and outside looking arrangement with

look and keys in duplicate 35 x 35 x 5 mm

M.S. Angle of Two Nos. one is welded and

other with nut and bolt for erecting Bakelite

sheet. Painting the Section Pillar inside and

out side with three tank powder coated paint.

section pillar roof should be without joint with

water leakage proof & tested as per IP

test & followed by IS 2147 of 1962 (B) 75 X

60 X 45 cm section pillar fabricated from

Gauge MS Sheet with angle iron legs 45 cm

long made from 35 X 35 X 5 mm thick MS

2 Nos 18 Supplying & erecting approved make IP 55 13218 13350.18 #NAME?

grade Company fabricated Timer Panel of

following capacity for switch On-Off street

lights on time scheduling basis made from

16G CRCA sheet duly epoxy power painted

inside and outside with hinged doors and

locking arrangement consisting of suitable

size of 4 Pole MCB and 4 pole contactor (cat-

III)with analog time switch, auto manual

switch of same make and suitable input and

output Bakelite terminals and with door

earthing approved by Engineer in charge. [B]

I/We am /are willing to carry out the work at…………% above/below percent (should be written in figures and

words) at the estimated rates mentioned above amount of my/your tender works out as under.

*Estimated Amount *Estimated Amount

put to Tender Rs. 743022.66 put to Tender Rs.

Deduction …………….. % below………………… Add ………… % above Rs. …………….

Less Dismental 0.00 Less Dismental

The rates are inclusive ofall taxes, transport charges,storage Charges except GST and applicable

GST Will be paid.(Add GST Extra)

The materials covered under contractor should be got approved from the Deputy Executive

Engineer. In chargeof the work

The materials and work shall have to be used and carried out as specification in technical

All Works Shall be Carried Out as per Public Works Department hand book and Other Specification

Of The division or as directed

Rate are Inclusive Of 1% Labourcess in Tender amount so 1% of total amount of bill will be

Rate are Inclusive Of 1% Labourcess in Tender amount so 1% of total amount of bill will be

deducted from the bill

Note-6TheMaterial to be used in this work should be approved strictly from engineer-in –charge /Deputy

Ex. Engineer as applicable.

Note-7The Agency will have to agree to carry out the work as per brand demand of concern deptt.

Note-8An amount of Rs.0.00 (Rs.Nill only ) towards estimated credit value of dismantled materials shall

be recovered from the 1st R.A. Bill of this work.

Signature of Bidder Deputy Executive Engineer

Electrical (R&B) Sub-Division