Development of 33 kV Sub Transmission infrastructure at Ernakulam District of Kerala under the Revamped Reforms-based and Results-linked Distribution Sector Scheme

BOQ - 1 - Reconductoring 33 KV line using 120 sq mm AAAC XLPE Covered conductor

33kV AAAC 120sqmm, Covered Conductor with water blocking component, stranded circular size (circuit length × 3% sag & maintenance× 3)

Supply of 33kV Grade, 120sqmm Joining Kit ( Full Tension Mid- Span Joint along with Heat Shrinkable Type)

Polymeric surge arrestors 33 kV class, 10 kA, Class 1

Insulating piercing connectors for 120 sqmm cable branching/tracking Surge Arrestors

Supply of Heat shrinkable outdoor termination kit ( bolted /crimped lug type) (1set = 3Nos)

Supply of wedge connector suitable for covered conductor to bare conductor connections

33 kV Class Polymeric Tension Insulator with special string hardware and accessories for 120 sq mm covered conductor

Pre formed plastic cable ties suitable to bind Covered conductor with Pin insulators

33 kV Class Polymeric Pin Insulator

33 kV Line isolator with structure

33 kV AB switch

Special channel Cross arm

1.8 m channel cross arm with CB&N

2.4 m channel cross arm with CB&N

4 line cross arm with CB&N

2 line cross arm with CB&N

3m channel cross arm with CB&N

A type 14m pole for 33 kv line

Lattice B type 14m pole for 33 kv line

V cross for 33 kV line with clamp b&N

Stay insulator 33kV

Stay tightner HT

HT stay rod

HT Anchor plate

HT Stay wire 7/3.15

GI wire 8 SWG 4mm

GI wire 4 SWG

GI Earth pipe , 40mm dia 2.5 m length

Supply & Providing GI grounding pipe , B – class , 40mm dia 2.5Mtrs 2.9 thick with bolts nuts, GI strips and washers complete for LA

Coil earthing

Bolt & Nut (various sizes)

ACSR Racoon

ACSR Rabbit

Channel clamp

PSC Pole 9m

11kV Composite Polymeric pin Insulator

11kV Polymeric disc insulator

LT Pin Insulator with Pin

LT Shackle Insulator with strap B&N

GI Strip 50*6mm

Hardware fittings HT

M S Cleat

F type bracket

Thimble HT

GI Clamp for HT strut

33 kV LA with structure

Description of Work / Item(s)

BOQ - 2 - 33 KV line using 120 sq mm AAAC XLPE Covered conductor

Surveying 1 km 33kV line using Ranging Rod.

Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared

Earth work excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) all classes of soil including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m to 3m, disposed earth to be levelled and neatly dressed. All classes of soil

Earth work excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) in ordinary rock including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m to 3m, disposed earth to be levelled and neatly dressed. Ordinary rock

Digging pit of standard size suitable for stay for A Pole/lattice tower in ordinary soil as per the direction of dept officers

Digging pit of standard size suitable for stay for A Pole/lattice tower in hard soil as per the direction of dept officers

Additional rate for excavation of Pit for 'A' type pole in Laterite.

Additional rate for excavation of 33kV 'A' pole in Hard laterite

Additional rate for excavation of Pit for 4 legged pole in Hard Laterite. (Item 182)

Additional rate for excavation of one Pit for HT Pole/HT Stay in Hard Laterite. (Item 128)

Additional rate for excavation of one Earth Pit (2.5m depth) in Hard Laterite. (Item 161)

Chipping removing the existing damaged, muffing portion of the existing pole structure without any damages to the structure for reconditioning the deteriorated muffing as per the direction of department officers at site ( using heavy hammer is prohibited.)

Pumping or Bailing out water and removing slush etc by using pump set including cost of labour, oil hire charges of pumpset, etc complete (Mechanical)

Dewatering Manual

Construction of earthern ring bunds for bailing out water for excavation for foundation and stub setting, including shoring, if necessary, with plaited coconut cadjan and bamboos, etc. as per dimensions noted below. Bunds upto 0.5 m height, 1 m bottom width and 0.5 m top width

Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

Stub setting in lines and levels using template in concrete foundation for 14 m A,B,C type lattice towers,etc as per specification and as directed by the departmental staff at site.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) (For levelling course)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level: 1:1.5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo - Mechanically Treated bars of grade Fe-500D or more

Providing concrete muffing of size 1x0.5x0.3m + 0.7x0.5x2.6m (0.45m above GL and 2.45m below GL). Excavation 1x0.5x2.45m CC 1:3:6, 20mm 1.0x0.5x0.3m + 0.7x0.5x2.6m, Plastering (1:3) 12mm (0.7+0.5)x2x0.6+(0.7*0.5)

Close timbering in case of shaft, well, cesspit, manhole and the like including strutting, shoring and packing cavities (whereever required) complete. (Measurement to be taken of the face area timbered) Depth exceeding 1.5M but not not exceeding 3M

Close timbering in case of shafts, wells, cesspits, manholes and the like including strutting, shoring and packing cavities (wherever required) etc. complete (Measurements to be taken of the face area timbered).

Plastering with cement mortar with 1:4, 12mm thick

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Dismantling 3 line ACSR DOG conductor including pin insulator string on the tower cross arm and pilot wire. Hire charges for tools, all hire and labour protection trestle and labour for providing suitable back stays at the time of dismantling etc complete.

Dismantling (without damage) one km 11kV line (3 conductors), cross arm, insulators, disc, rolling the conductor and stacking.

Dismantling (without damage) one km LT 3ph 4 wire OH line, cross arms, insulators and stacking the conductors in rolls.

Dismantling and reconnecting Sph service connection from the OH line including lowering down the WP portion.

Dismantling and reconnecting 3ph service connection from the OH line including lowering down the WP portion

Dismantling (without damage) one 11kV 'A' type pole after disconnecting stays, strut etc. and stacking the same.

Dismantling (without damage) one 11kV PSC/RCC pole after disconnecting stays, strut etc. and stacking the same.

Dismantling (without damage) one LT PSC/RCC pole after disconnecting stays, strut etc. and stacking the same.

Dismantling one ordinary street light/CFL/LED fitting from existing pole and refitting the same on newly erected pole and reconnecting.

Dismantling (without damage) one HT stay incl. back filling, and bringing back to section store.

Dismantling 1No stay to lattice/A pole and backfilling

Dismantling 1No V/Channel X arm on existing pole

Dismantling of Channel Cross arms (old & corroded) from the A Pole DP's structures for the purpose of renewing with new ones

Dismantling of 33kV Pin insulator sets from the A Poles and DP's structures for facilitating the fitting of 33kV class polymeric pin insulator for the drawal of covered conductor purpose of renewing with new ones

Dismantling of 33kV tension disc insulators from the A Poles and DP's structures for facilitating the fitting of 33kV class polymeric tension insulators for the drawal of covered conductor purpose of renewing with new ones

Dismantling of 33 kV A type Poles being old & corroded including digging the pits & backfilling the soil after disconnecting the stays, strut etc & stacking the same

Dismantling of 33 kV A type Pole DPs being old & corroded including digging the pits & backfilling the soil

Dismantling one damaged DP structure with PSC pole and stacking the same

Transporting 4 legged lattice structure of all sizes by head load for an average distance of 1 Km where tranportation by hand cart is not possible (normally limited to 0.3 km)

Transporting poles by hired vehicle to a distance beyond 5km and carrying upto 4 poles excluding loading & unloading

Transporting lattice tower parts and connected accessories including loading and unloading charges etc as directed by Board staff to an average distance of 5 Km by lorry.

Transporting poles by hired vehicle to a distance upto 5km and carrying upto 4 poles excluding loading & unloading

Transporting A pole by headload

Transporting of dismantled Insulators and accessories, power conductor accessories and earth conductor accessories etc from work site to substation compound

Transporting of dismantled Line and earth conductor - upto 10 km

Transporting 33kV 14 M 'A' type pole by Head load (limited to 0.3km).

Transporting of newly supplied V Cross arms/ Channel Cross arms, Earth pipes and accessories from the section store to the work site including the conveyance from nearest vehicle access Point to the worksite

Transporting empty cable drum from work site to storage yard for an average distance of 5 km

Transporting 33 kV, 3 core Aluminium cable drum with cable from storage yard to site for an average distance of 5 km including the loading charges from the store and unloading charges at the work site

Loading HT 4 legged pole from the stacking place and unloading the same at work site (Transport by vehicle)

Loading HT 'A' type pole from the stacking place and unloading the same at work site (transport by vehicle).

Loading 33kV 14 M A type pole to hand cart from the nearest accessible point of the vehicle to the work location including the unloading charges at the site

Fabrication of structures for erecting equipments. The GI & MS angles will be supplied departmentally

Erection of structures above the ground level and assembling of members using bolt and nut including punching of holes, as per approved drawing and direction of the departmental staff at site.

Fitting and erecting one 33kV 'A' type Single Pole in position, including fitting cross arm, digging and back filling pit in ordinary soil (as per standards), drawing sufficient length of GI earthing leads from F clamp through V cross arm to the ground for earthing (excluding provision of earthing)

Erection and commissioning line AB switch

Fitting and providing one 33kV stay including digging & back filling pit.

Providing Cut end stay by piling Cut Ends in kole land incl. anchor plate(size 450x450x7.5mm GI) at cut ends and conveyance.

Renewing one V cross arm on the existing 33kV pole(item 342)

Renewal of existing damaged/old 11kV Strut with new PSC strut in place incl. excavation & backfilling pit and conveyance (except pole).

Fitting one Additional Channel cross arm (100x50x6mm), in existing A Pole/Lattice including conveyance of materials.

Additional rate for refitting/redoing one Disc set while renewing any type of 11kV cut pole

Laying of departmentally supplied GI strip/Copper strip of suitable size including cleaning and neatly bending of strips ,cutting, removing of metal/earth in the yard and burying earth strip to the required depth re-doing the yard metalling as per the direction of the departmental officers.

Drilling hole of various sizes on existing Channel/Cross Arm.

Drilling oval shaped hole of various sizes on existing Channel/Cross Arm/GI/MS cleat etc.

Drilling holes in yard structure

Cutting of steel Angles

Cutting of Channel Cross arms /V Cross arms angle etc into two pieces wherever unbolting becomes impossible

Fitting 1no additional V/Channel X arm on existing pole

Fitting and providing one Strut using HT PSC pole incl. digging & back filling pit. (Item No. 120)

Fitting and erecting one No 33kV DP using 'A' type pole in position incl. fitting 2 channel cross arms, digging & back filling pit, drawing earth leads.

Fitting and providing one 33kV Fly stay for 33kV pole using 'A' type pole incl. digging & back filling pits.

Welding overlapping joints of 50x6mm GI strip with 50mm long, 6mm thick welding on all three sides after doing 2 Nos. bolted joints at the centre as specified after cleaning the surface. Charges includes hire charges of DC arc welding set, current charges, cost of low hydrogen content DC arc welding electrodes( No.E7018) cost of anti corrosive paint etc. complete.

Welding one end of the GI strip 50x6mm with the structure with a welding length of 50mm & 6mm thickness on both sides & end of the strip and connecting other end with bolts & nuts if required including hire charges of DC arc welding set, current charges, cost of low hydrogen DC arc welding electrodes (No.E7018) cost of anti corrosive paint etc. complete.

Stringing of 33kV, 120sqmm XLPE Covered Conductor including fitting of all accessories, providing end terminations, midspan joints, pipe earthing, installing insulated piercing connectors etc

Stringing of one km 11kV line with ACSR Raccoon (3 conductors) incl. cutting and removing tree branches wherever necessary.

Stringing one km LT 3ph 5 wire line (Rabbit for Ph and Weasel for N&St.main) incl. fitting cross arm etc. removing touchings and conveyance of materials.

Providing protection for telephone cables, LT, HT and OH lines, traction lines, buildings, road crossing, railway crossing, etc., beneath the line by providing suitable scaffoldings at the time of stringing and dismantling.

Transferring LT 3ph 4/5 wire OH line to newly erected HT/LT pole and refitting all items to the new pole.

Providing one Earth using earth pipe (size 3 m) including digging & backfilling pit and supply of charcoal, salt, sand etc.

Providing one Coil Earth using GI earth wire, No.8 GI-earth wire (50mm dia, 115 digging separate pit at standard distance away from the turns) including digging separate pit (0.45x0.45x1.5m) at standard pole/structure & backfilling.(163)

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work

Pole numbering using printed Aluminium sheets / Painting the surface of pole with anti algal yellow paint and painting Letters with black paint as specified incl. cost of paint. (776)

Display signboard- Fabricting and supplying stainless steel plates 304 grade for Engllish or malayalam letters of specified hight tickness and fixing on the wall. Rate includes coast of conveyance of all materials labour charges for cutting fabrication assembling, errection, welding, curvaturing, grinding, finishing, chilling screwing and scafolding charges etc. comlete and fixing the letters in correct line and level as directed by the department officers at site.

Description of Work / Item(s)

Total Amount excluding GST of BoQ1 (Plant and Equipment)

Total Amount excluding GST of BoQ2( Installation /Erection charges)

Total Amount excluding GST of BoQ1 +BoQ2

Unconditional Discount Offered by the Bidder (if any) in Rs

Grand TOTAL (Sl.No.3-Sl.No.4)

Description of Work / Item(s)

BOQ - 4 - Reconductoring 33 KV line using 120 sq mm AAAC XLPE Covered conductor

33kV AAAC 120sqmm, Covered Conductor with water blocking component, stranded circular size (circuit length × 3% sag & maintenance× 3)

Supply of 33kV Grade, 120sqmm Joining Kit ( Full Tension Mid- Span Joint along with Heat Shrinkable Type)

Polymeric surge arrestors 33 kV class, 10 kA, Class 1

Insulating piercing connectors for 120 sqmm cable branching/tracking Surge Arrestors

Supply of Heat shrinkable outdoor termination kit ( bolted /crimped lug type) (1set = 3Nos)

Supply of wedge connector suitable for covered conductor to bare conductor connections

33 kV Class Polymeric Tension Insulator with special string hardware and accessories for 120 sq mm covered conductor

Pre formed plastic cable ties suitable to bind Covered conductor with Pin insulators

Amrutha Associates

Manipal Energy & Infratech Limited

Manipal Energy & Infratech Limited

Manipal Energy & Infratech Limited