ADDITION ALTERATION AUGMENTATION TO BLDG NO. P-65 (SIR JC BOSE AUDITORIUM) AT DEAL DEHRADUN UNDER GE (I) RnD DEHRADUN

Amount

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meteres lead for thickness of tiles 10mm to 25mm.

Dismantling doors, windows and clerestory windows of area 3.00 sqm and below (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Dismantling wooden boardings 10mm to 25mm thickness in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead :

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge:In Cement Mortar

Demolishing cement concrete nominal 1:3:6 or richer mix manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Dismantling old plaster/grit wash or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Dismantling of 75 to 80mm dia C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead.

Dismantling of 100mm dia C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead.

Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) for nternal Work- Exposed on wall as per direction of Engineer- in-Charge.

Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in-charge.

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick area of each coloured tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including Screed bed (or) bedding layer of mortar 15mm thick for laying floor finishes CM (1:6) complete all as specified and directed.

M&L for providing and fixing Ist quality ceramic glazed wall tiles of size 350x250mm/450x300mm conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados, over and including 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

M&L for providing and laying Polished Granite stone slab colour of Black, cherry/rubby Red or equivelent flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

M&L for providing and laying Glazed Vitrified tiles Matt/Antiskid finish of size 600 x 1200mm in verandah/passage floor and dados (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid over and including 20 mm thick cement mortar 1:6 (1 cement: 6 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily all complete as specified and as directed by the E-in-Charge.

M&L for 25mm thick kota stone slab flooring over and including 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

M&L for providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately)

S&F powder coated aluminium for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

M&L for providing and fixing 12 mm thick prelaminated particle board with decorative laminatiion on both sides flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

M&L for providing and fixing glazing with float glass panes of 5 mm thickness (weight not less than 12 kg/ sqm) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

M&L for providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315 (with stainless steel cover plate minium 1.25mm thickness), having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

M&L for providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable Casement window double panels with S.S. friction hinges (300 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window above 0.75 sqm upto 1.50 sqm).

Providing and fixing factory made two track two panels sliding window made of (small series) uPVC white colour sliding glazed window frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

M&L for providing and fixing 4mm thick glazing with float glass panes (weight not less than 10kg/sqm) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

M&L for providing & fixing frosted glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with 4.0 mm thick glass panes (weight not less than 10 kg/ sqm)

M&L for providing and fixing M.S. grills of required pattern in frames of windows by welding etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

M&L for anti termite treatment along the external/internal wall below concrete /floor or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes of 12mm dia and 150mm deep inclined at 45 degree at every 750mm centre to centre etc.complete all as specified and directed by Engr-in-charge.

M&L for anti ternite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre 6mm dia and sealing the same complete all as specified and directed.

M&L for Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) complete all as specified and directed.

M&L for providing and laying in position cement concrete of specified grade excluding the 1:2:4 type-B1 (1: Cement, 2: Sand, 4: aggregate) as in coping etc. including centering/shuttering complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2, 75 mm thick using 40mm graded stone aggregates as in plinth protection/sub base of paving surface complete finished fair and even without using extra cement.

M&L for 75mm thick PCC 1:2:4, type B-1 (using 20mm graded stone aggregate) finished even and smooth without using extra cement as in flooring complete all as specified and directed.

M&L for removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

M&L for 15 mm cement plaster on Brick / concrete surface of wall of mix :1:4 (1 Cement : 4 Sand) Complete all as specified and directed.

M&L for 15mm cement plaster in CM 1:6 on fair finished wall surfaces all as specified and directed by Engineer-in-Charge.

M&L for 10mm cement plaster in CM 1:6 on ceiling surface/concrete surfaces all as specified.

Removal of existing roof treatment with plastering and cleaning the surface with wire brushes and washing and drying the top surface for execution of work complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 on fair face of existing roof surfaces finished even and smooth without using extra cement using liquid water proofing compound as per manufacturer instruction complete all as specified and directed.

Supply only liquid water proofing material in cement plaster work in proportion 200 ml per cement bag of 50 Kg or recommended by the manufacturers.

M&L for providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layered 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt including of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/ 450N/ 5cm. Tear strength in longitudinal and transverse direction as 300/ 250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. Hot liquid bitumen to be applied over membrane after laying for enhancing the life of treatment. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane.

M&L for two or more coats of aluminium paint of approved brand and manufacture to give an even shade over roof treatment all as specified and directed.

M&L for preparation of new plastered surfaces of wall distempering with oil bound washable distemper of approved brand and manufacture to give an even shade (two or more coats) over and including water thinnable priming coat with cement primer complete all as specified

M&L for (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm on new finishing walls with textured exterior paint of required shade : including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

M&L for two coats of distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.

M&L for finishing walls with textured exterior paint of required shade or old work (Two or more coats on existing cement paint surface applied @ 3.28 ltr/10 sqm complete all as specified and directed,

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

M&L for reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral staircases above plinth level up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 using 20mm graded stone aggregate.

M&L forCentring and shuttering including strutting,ropping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform complete all as specified and directed.

M&L for Thermo-Mechanically Treated bars of grade Fe-500D or more. reinforcement for R.C.C. work ready to use "cut and bend" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete above plinth level.

M&L for providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge: Profile C Fixing with adjustable lugs with split end tail to each jamb.

M&L for providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws complete all as specified and directed

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer- in-Charge.

Providing and fixing of 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a PVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a PVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a PVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge.

S&F PVC coloured vertical blind hanging on powder coated hanging arrangement including roller and all necessry fixing and fetures as per manufacture instruction. or directed by GE/Engr-in-Charge complete all as specified and directed.

S&F mortice lock, vertical type of size 100 mm with brass body 2 lever complete all as specified.

M&L for Solid PVC Wall Lining consisting of 5mm thick plain PVC sheet used inclusive of solvent cement and fixing at site as per specifications and drawing complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

M&L for providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.

M&L for providing and fixing ISI marked 100x58x1.90 mm stainless steel butt hinges bright finished with necessary screws etc. complete :

M&L for providing and fixing 200mm size stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge.

M&L for providing and fixing ISI marked stainless steel tower bolt fancy type with necessary screws etc. complete :200x10 mm

-Ditto- all as per item Ser No. (62) above but size 150x10mm

S&F 300mm long stainless steel, fancy sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy all as specified and as directed.

M&L for providing and fixing bright finished stainless steel hasp and staple (safety type) with necessary screws etc. complete : 115mm size.

M&L for providing and fixing chromium plated brass 100 mm mortice latch and door lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

M&L for providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter

-Ditto- all as per item ser No. (67) above but 75mm dia .

M&L for providing and fixing 110x110x110 single tee with door on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

-Ditto- all as per item ser No. (69) above but 75mm dia .

S&F single bend of 110mm dia complete all as specified and directed.

-Ditto- all as per item ser No. (71) above but 75mm dia .

S&F in repair 100 mm dia Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) (using 20 mm graded stone aggregate) complete all as specified and directed.

S&F in repairs PVC (SWR) gully trap 150/100 mm, setting and jointing with solvent cement, complete all as specified and directed.

M&L for one or more coat of painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade on old steel surface all as specified.

M&L for providing and fixing in repairs counter top white vitreous china wash basin of size 610x410x109mm with 15 mm C.P. inlet. 32 mm C.P. brass waste of standard pattern, including cutting of granite in oval shape/desired shape with griding edges of stone and cutting and making good the walls wherever require: White Vitreous China Wash basin of size as approved by GE complete all as specified and directed.

S&F in repairs 15mm brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed for WHB all as specified and directed.

M&L for providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and including dismantling of old one and direction of Engineer-in-charge.

M&L for providing and fixing in repairs CP brass toilet paper holder complete all as specified and directed.

M&L for providing and fixing 15mm dia G.I. pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall

M&L for providing and fixing 20mm dia G.I. pipes complete with G.I. fittings and clamps, including concealed pipe, including painting with anti corrosive bitumastic paint, including cutting chases and making good the wall.

M&L for providing and fixing 25mm dia G.I. pipes complete with G.I. fittings and clamps, including concealed pipe, including painting with anti corrosive bitumastic paint, including cutting chases and making good the wall

Fixing only of 15mm dia GI tubing received from taking down items.

Fixing only 20mm dia GI tubing received from taking down items.

Fixing only of 25mm dia GI tubing received from taking down items.

M&L for providing and placing on terrace (at all floor levels) 1000 liters capacity polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

S&F 20mm ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed

M&L for providing and fixing 25mm gun metal gate valve with C.I. wheel of approved quality (screwed end) :

-Ditto- all as per item ser No. (88) above but 20mm dia .

M&L for providing and fixing 15mm bore, 450mm long uplasticised PVC connection pipe with brass unions :

M&L for providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan including necessary fittings and white solid plastic seat with lid etc. and including dismantling of old one complete all as specified and directed.

M&L for providing & fixing in repairs White vitreous china water closet squatting pan (Indian type/Orissa pattern W.C Pan of size 580x440 mm) along with "S" or "P" trap including dismantling of old WC seat and "S" or "P" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material including malba, all complete as per the direction of Engineer-in charge complete all as specified and directed.

M&L for providing and fixing P.V.C. low level flusingh cistern 10 Ltr capacity (white) with manually controlled device (Handle lever) conforming to IS:7231, with all fittings and fixtures complete

S&F in repairs 600 mm long 20mm dia brass chromium plated tubular towel rails,all as specified.

S&F in repairs100 mm dia CP brass grating round with hole complete all as specified.

S&F in repairs 15 mm dia angle cock (two way) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe for fixing of health faucet and PVC connections etc. all as specified and directed.

M&L for providing and fixing in repairs 15mm C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

M&L for providing and fixing in repairs 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and fixed in position and make as approved by Engineer - in - charge.

M&L in repairs for aluminium drapery rod outer dia 25mm with powder coated paint thickness welded MS pipe with corrugated PVC extrusion having plastic rings made of ABS plastic with outer dia 56-58 mm & inner dia 40-42mm . Brackets shall be at galvanised steel 1.6mm thick including taking down old one complete all as specified and directed.

M&L for providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

M&L for providing and fixing steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required as in n gratings, frames, guard bar, ladder, railings, brackets, gates and similar works complete all as specified and directed.

M&L for painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture

M&L for two or more coats of glue sizing with copal varnish over an under coat of flatting varnishing of approved brand and manufacture complete all as specified and directed.

M&L for removing the plants/ vegetation from bldgs more than fifth story height including penetreated roots complete and injecting chemical GLYPHOSPHATW 41% SL 20 ml or till refusal by makimg cut/ injection in the stem of plant 30mm C/C spraying with solution (25ml Glyphospoto 41% diluted with one litre water) including necessary scaffolding etc work will be carried out from bldgs more than 5th storey but upto 8th storey with and including dismantling of plain or corrugated steel sheeting, any gauge, thickness complete all as specified and directed.

M&L for 3.20 / 3.30 Lineoleum , plain colorued, laid dry in floors including streching, cutting and fixing and sealed with approved adhesive with and including dismantling existing floor complete all as specified and directed.

M&L for providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

M&L for providing & Fixing of Woodslat NRC 0.88 with pre laminated matt finish panels Supplying of FR Grades 2430x131x16mm made of exterior grade HDHMR backed with acoustical Fleece providing sound absorption of 0.88 NRC.To be installed with 15mm Aluminium profile conformsto Aluminium Alloy 6063-T 6.Temper As per BS:1474- 1987 and G.I Lock in clips on the back of tongue and Groove system. The density per panel is minimum 750-800 kg/m3. The panels come with tongue & groove for seamless patterns, 4-28mm Groove and visible panel. These slats should comes with linear perforations for excellent uniformity. The perpendicular holes are available on the back of panel which are covered by black acoustical fleece. Achieves sound reduction of 0.88 NRC. To be installed on GI Studs (48mmx48mm) .5mm thickness or better with a backing of Polyster Fiber Wool Coverd with Chicken mesh Jali from both sides. 50mm thick,1000 GSM absorb wool tested as per Fire Retardant ASTMD 635-1991 Insulation and IS 15061-2002 for excellent results. Complete in all respect and to be approved by Architect and his representative including dismantling of old one.

M&L for providing & Fixing of 9mm thick seamless polyster fiber board FR frades panels providing sound absorption of 0.90 NRC.To be installed on 8mm thick perforated HDHMR panels with industrial adhesive. The density per panel is minimum 1800GSM. The panels made from recycled material. Achieves sound reduction of 0.90 NRC. To be installed on GI Studs (48mmx48mm) .5mm thickness or better with a backing of Polyster Fiber Wool Coverd with Chicken mesh Jali from both sides. 50mm thick,1000 GSM absorb wool tested as per Fire Retardant ASTMD 635-1991 Insulation and IS 15061-2002 for excellent results. Complete in all respect and to be approved by Architect and his representative including dismantling of old one.

M&L for providing and fixing 18 mm thick plaster of Paris (gypsum anhydrous) ceiling including providing coves, slopes etc. as per the drawings , over GI ceiling sections framing consisting of 24 gauge GI intermediate channel, ceiling sections, parameter channels and GI suspenders. The GI frame to be suitably suspended from the ceiling as per the design drawings. Further fixing on it a square mesh of app. size 9mm x 9mm. The plaster of Paris coating to be appllied in 2 layers for better finishing. The work to be executed in the shapes as per design drawings, including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed. The rate also includes painting with 2 or more coats of plastic emulsion paint all complete as per specification and direction of the Engineer in Charge . Nothing extra will be paid for light cuttings/grills/diffusers, cutouts, trap door etc. No extra channel will be paid if it is required for additional support etc. All complete as per the directions of Architect or Architect's representative including dismantling of old one.

M&L for providing & Fixing of Stage Wall Paneling Wall Panelling Wood Fiber cement Fibrette tile Size 595x595x20 mm NRC1 with GI Studs (50mmx50mmx50mm) Supplying Wood Fiber tiles made of Wood Fibre 1mm width cement composites 15mm thick with Black colours as per the choice of the Architect/ person in charge of size 595x595x15 mm. Has excellent noise absorption of 1 NRC as per ISO: 354-1985 and ASTM 423-90 a, Density 400 Kg/ m3, meets stringent Fire Ratings ASTMD-876 and Fire Class -1 as per BS 476 part 5 and 6,Class P-not easily ignitable as per BS-476-Part 5 (Ignitability for material).This is applicable for core and class 1 as per BS 476- Part 7 (Method for classification of surface spread of flame) ,weather resistance as per IS 3308, Thermal Insulation as per IS:3346-1980 with relative humidity of 90% RH at 60o Celsius(140o Fahrenheit) for 15 days= No deterioration. Conforms to En 131682001 and are RoHS Complaint. To be installed on GI Studs (50mmx50mmx50mm) with a backing of Polyster Fiber Wool. 50mm thick,1000 GSM absorb wool Coverd with Chicken mesh Jali from both side. tested as per Fire Retardant ASTMD 635-1991 Insulation and IS 15061-2002 for excellent results. Complete in all respect and to be approved by Architect and his representative including dismantling of old one.

M&L for providing & Fixing of Stage Celing Wood Fiber cement Fibrette tile Size 595x595x15 mm NRC1 with T-24 Grid Supplying tiles made of Wood Fibre 1mm width cement composites 15mm thick with an option ofcolours as per the choice of the Architect/ person in charge of size 595x595x15 mm . Has excellent noise absorption of 1 NRC as per ISO: 354-1985 and ASTM 423-90 a, Density 400 Kg/ m3, meets stringent Fire Ratings ASTMD-876 and Fire Class -1 as per BS 476 part 5 and 6,Class P-not easily ignitable as per BS-476-Part 5 (Ignitability for material).This is applicable for core and class 1 as per BS 476- Part 7 (Method for classification of surface spread of flame) ,weather resistance as per IS 3308, Thermal Insulation as per IS:3346-1980 with relative humidity of 90% RH at 60o Celsius(140o Fahrenheit) for 15 days= No deterioration. Conforms to En 131682001 and are RoHS Complaint. To be installed on T-24 Grid system with a backing of 50mm 1000 GSM thick absorbwool tested as per Fire Retardant ASTMD 635-1991 and IS 15061-2002 for excellent results. Complete in all respect as desierd by the Engineer in charge / Consultant of work at site including dismantling of old one.

M&L for providing & Fixing of 70mm thick Wooden Partition Procenium from Stage flooring to Celing as approved by architects. Providing & Laying of 70mm thick proscenium M.S Frame 50x50mm at 600 mm c/c in on other direction, the framework to be filled with 50 mm thick Absorbwool density 48 kg/m3. and finished with 10mm commercial ply both the side firmly screwed in MS section and laid as per design & drawing. Complete in all respect and to be approved by Architect and his representative.

M&L for providing and fixing of Stage Flooring 75x18 mm thick in random length, 2nd class teak wood planks flooring with T&G joints on a layer of 19 mm thick ply (Greenlam or Century) fixed to hard wood, 50x50 mm at 600 mm c/c in other direction, the framework to be filled with 50 mm thick rockwool density 48 kg/m3.PU polishing of teakwood on exposed surface and synthetic paint over pink primer on hidden surfaces in horizontal/vertical plane (rate for flooring shall include providing additional framework required for housing microphone and power outlet junction boxes including providing & fixing of hinged 18 mm thick teakwood cover for junction boxes. Complete in all respect and to be approved by Architect and his representative.

Providing and fixing of Fire Rated/Acoustical Wooden Doors: Supply & fixing of 70mm thick 38 db acoustic door having infill of 47mm thick resin bonded glasswool of 24kg/ M3 density coated with FR Acrylic Sealant Sandwiched between two 9 mm thick starpan calcium sillicate boards without asbestos, Brucite and Meerschaum having a density not more than 1150kg/ M3 and thermal conductivity 0.14 W/M*K faced with 6mm thick commericial ply with heat activated intumescent fire seal strip of size 10mm x 4mm mounted in the grooves having hardwood lipping of size 15mm x 70mm and 1mm thick laminate facing on both sides in desired shade and colour. The rate should also include Red Merrandi Frame 145 x 70mm with Commercial Ply Facing (6mm + 4mm Teak Ply on both sides) at all heights including scaffolding. Complete in all respect & entire satisfation of the engineer in charge/Architect including dismantling of old one. ( Note:- Contractor to submit Test certificates from manufacturer).

M&L for providing & fixing of Double Leaf Panic Bar set along with Panic Trim for operation from the other side of the Panic Bar Complete in all respect to entire satisfaction of the engineer-in-charge/Architect.

M&L for providing & fixing SS Ball Bearing Hinges of size 100 x 75 x 3mm fixed with SS Screws Complete in all respect to the entire satisfaction of the engineer-in-charge/Architect.

M&L for providing and fixing of Door Closer: Providing & fixing of Fire Rated Heavy duty door closer complete in all respect to the entire satisfaction of the engineer-in-charge/Architect.

M&L for providing & fixing 25mm dia & 400mm long brushed steel finish pull handles with long bolt and cap for fixing from outside only complete in all respect to the entire satisfaction of the engineer-in-charge/Architect.

Providing & fixing of first class teak wood skirting of size 25 x 100mm to be fixed over existing frame work including polyurethene polish complete as per drawing and to the entire satisfaction of Engineer-in-charge/Architect. Complete in all respect as desierd by the Engineer in charge /Architect.

M&L for providing and fixing of 2 mm thick homogenous Anti static Polyflor or equivalent XLPU Polyvinyl chloride sheet/tile in flooring and skirting in approved pattern on a smooth and damp proof base using rubber based adhesive of aproved quality and manufacturer like Dunlop or equivalent including rolling with wooden rollers weighing about 5kgs all complete as directed by Engineer-in-charge, in approved colour and shade. Complete in all respect as desierd by the Engineer in charge / Consultant of work at site.

M&L for providing and fixing of built in box type wall cabinet to 750 mm deep 750 high with 100 mm wide skirting recessed by 12 mm as per design duly finished with 1mm steam beach laminate over 19 mm thick BWP commercial ply housing sound and light console as per design complete with all hettich or equivalent hardware locks handles and fittings. The inside of the box shall also be finished with 1mm thick steam beach laminate duly edged with rubber wood. complete with drawer slides ,tray,hardware complete to the satisfaction of Engineer –in-charge.

M&L for providing and fixing of toughened Transperant Glass -10mm thick shall be Installed with Wooden frame work made out of100 x 50mm thick sal wooden Chowkth. Complete with hardware complete to the satisfaction of Engineer-in- charge.

M&L for providing providing and fixing of thermal insulation of ceiling/ wall (under deck insulation) with Resin Bonded Rockwool conforming to IS: 8183,density 48 kg/ m3, 50 mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5mm x 24 gauge wire mesh, for top most ceiling of building.Complete in all respect and to be approved by Architect and his representative including dismantling of old one.

M&L for providing & Fixing of Flocked textile floor covering of Nylon 6.6 face fiber or equivalent of approved make with 100% Nylon and completely water proof resilient backing. The flooring should be Anti static with thickness of 4.3 mm and approximate weight of 1.8 k.g./sqm of roll form. The carpet should be completely stain resistant and of a density approx. 80 million fibers/sq.mtr (70 million fiber/sq.yd) in the width of 2 mtr .The floor covering should have Fire Test EN-13501, Appearance Retention Hexapod ISO 140-8, Friction Slip Resistance Test EN 14041 Class DS, SANITISED anti-microbial treatment, with resilient waterproof backing, anti allergic which is certified by British allergy foundation, with ten year replacement guarantee. The carpet should have permanent static control. Complete in all respect and to be approved by Architect and his representative including dismantling of old one.

M&L for providing & Fixing of Fibre Glass Acoustical Suspended Ceiling System with 15 thick black Board Edge Tiles with 24mm face exposed grid. The tiles shall have smooth laminated visual with Humidity Resistance (RH) of 95%, NRC 0.85 – 0.95 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, Light Reflectance ≥85% as per ASTM E-1477, Colour Pebble Black, Fire Performance of Class 0/1 as per BS 476 Part 6/7 with 15/20/25mm Board edge in module size of 600 x 600mm. It shall be suitable for Green Building application, with Recycled content of 66% (GW)/ 74% (RW). INSTALLATION: The tile shall be laid on 24 mm wide T - section flanges colour global black (matching to tile colour) having roll formed double stroke rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm (all sections). The deflection loading of the system shall be 15 kg/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360) with a deflection loading of 18kg/m. The end details of the cross tee shall be made of pre hardened steel and fixed to the ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”. All main beam to main beam and cross tee to cross tee connection shall have a pull out strength of more than 100kg. The T Sections shall be made of hot dipped galvanized steel of 90 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability including dismantling of old one complete in all respect as desierd by the Engineer in charge / Consultant of work at site.

M&L for providing & fixing of horizontal level suspended ceiling comprising of Vertical Linear Baffle Ceiling made out of Aluminum Extrusion in Aluminum alloy grade 6063 T5. The baffle blade shall be in size of 100x25x3600mm in powder coated to Woodgrain/Plain finish (Red Oak, Cherry, Black / White). The baffle shall be electrostatically polyester powder coated to a coating thickness of 60-80 micron. The powder coating shall pass Salt Spray Test for 750 Hours as per ASTM B117, QUV –A Test for 1000hours as per ASTM G-154 – (Cycle – 1) and Humidity test for 1000hours as per DIN 50017. The powder coating shall have an adhesion of GT0 as per EN ISO 2409. The shade variation within a manufacturing batch shall be delta E<1 using Excite/BYK Gardner instrument and gloss level 25±5% at 60˚ as per ASTM D523 (Not applicable of Wood Grain Shade). The baffle blade shall be suspended using Slotted U-profile of 20 x 30 x 3700mm (Thk-1.5mm) having slots in module of 25mm to keep baffles at an on-center spacing in multiples of 25mm. Longer lengths of Baffle to be connected by Baffle Joiner and the ends to be fixed with End caps. INSTALLATION: Shall be hanged using baffle hanger from U-profile made of mild steel with powder coating thickness of 60-80 micron. The U – profile to comprise of alternate square & rectangular slots of 6.5x6.5mm & 28x6.5mm respectively on the web for locking the baffle hanger using plugin clip to secure the hanger in perfect position and achieve uniform spacing between baffles. The overall dimension of the U – profile is 20(W) x 30(H) x 3750(L) mm and is rolled form from 1.5mm thick mild steel with a powder coating thickness of 60-80micron. U- Profile to be connected to each other using U –Profile Splice. The U- profile shall be hanged from the true ceiling using threaded rod using a U- Profile hanger including dismantling of old one Complete in all respect as desierd by the Engineer in charge / Consultant of work at site.

M&L for providing & fixing of at all height 12mm thick gypsum false ceiling including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanized in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6mm thick with flanges of 22 mm and 37 mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastner 12.5mm dia x 40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required lengths, and other end of the angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm center to center to which the ceiling section 0.5mm thick button wedge of 80 mm with tapered flanges of 26 mm each having clips of 10.5mm at 450mm center to center shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partition with the help of rawl plug at 450 mm center to center with 25mm long drive-all screws @230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer & two coats of plastic paint including of dismantling of old one.

M&L for Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure upoto plinth level for manholes in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand) complete all as specified and directed.

M&L for providing and laying in position cement concrete of specified grade of 1:2:4 type B-1 (1: Cement, 2: Sand, 4: aggregate) excluding the cost of centering and shuttering - All work up to plinth level complete all as specified and directed.

M&L for PCC 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) for coping of manholes, parapet walls etc.

Providing precast reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20mm nominal size derived from natural sources) complete all as specified and directed.

Thermo-Mechanically Treated bars of grade Fe-500D reinforcement for R.C.C. work ready to use "cut and bend" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete above plinth level.

Earth work in excavation in all kind of soil by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge complete all as specified an directed.

Dismantling of old S.W. pipes of 150mm dia including breaking of joints and bed concrete stacking of useful materials near the site within 50 m lead and disposal of unserviceable materials into municipal dumps

M&L for providing, laying and jointing glazed stoneware pipes 150 mm dia class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete all as specified and directed.

M&L for making connection of drain or sewer line of 100mm to 250mm dia with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete all as specified and directed.

M&L for providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes of 150mm dia including bed concrete as per standard design

M&L for 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix in CM 1:3 (1 cement: 3 fine sand).

M&L for 15 mm cement plaster ( external ) on brick wall/ stone wall in CM 1:4 (1 cement: 4 fine sand) complete all as specified and directed.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

M&L for PCC type C-1, 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) as in sub base of floor finished even and smooth complete all as specified and directed.

M&L for chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, over and including 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : Light shade pigment using white cement.

M&L for providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc.

Taking down existing MCB/MCCE/DB box any type/size and making good disturbed surfaces of walls, floors, etc. complete as directed.

Taking down LED light fittings 1'x1', 1'x4', 2'x2' feet of any type and size from ceiling and roof of any height and refix the same after necessary repair of civil and elect work etc complete all as specified and directed by Engr-in-charge.

M&L for wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.complete all as specified and directed by Engineer-Charge.

M&L for wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

25 mm internal dia 1.6 mm thick

32 mm internal dia 1.6 mm thick

40 mm internal dia 2.0 mm thick

50 mm internal dia 2.0 mm thick

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

M&L for numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required and directed by Engineering-in-Charge.

M&L for wiring for group controlled (looped) light point /fan point / exhaust fan point /call bell point (with out independent switch etc) with 1.5 sq mm FRLS PVC insullated cooper conductor with single core cable in surface / recessed PVC conduit , and earthing the point with 1.5 sq. mm FRLS PVC insulated cooper conductor with single core cable as required.

Supplying and Fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos 3 pin 5/6 A modular socket outlet and 2 nos . 5/6A modular switch , connections etc . As required ( for light plug to be used in non residential buildings)

Supply & fix VPTN DB enclosure with vertical type load line distribution board, double door, 4 way AC 3 Phase 415 volt with TPN bus bar 250 Amps for each phase with 2 Neutral bar, 2 Earthbar and with provision for DPX3 200 MCCB as incomer and SP/TP MCB's as out going complete all as specified and directed by by Engr-in-Charge

Supply & fix MCCB 4 Pole, 200 Amps 415 Volts, 25 Hz having breaking capacity 36 KA, with thermal magnetic protection unit for existing LT Panel and testing complete all as specified and directed

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

Supply & fixing of LED Tube light with fitting 18 watts, 4 feet long energy savings surface mounted luminarie with high efficiency PMMA diffuser gives soft glare free light.complete all as specified .

Supply & fixing of batten holder, PVC body angular type 230V,

Supply & fixing of LED lamp 9 watts, 3000K, energy savings with cool day type, complete all as specified and as directed.

Supplying and fixing 12 way double door, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

8 way (4 + 24), Double door

12 way (4 + 30), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts 10 KVA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts 10 KVA, "C" curve, miniature circuit breaker suitable for inductive load of single poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supply & fixing of ceiling rose 3 plates polycarbonates, isolated body complete all as specified and directed.

Supplying & laying XLPE insulated PVC sheathed Aluminium Conductor armoured UG cable of 1.1 KV grade Conforming to IS 7098/1988 with upto date ammendment of following size in the existing RCC/HUME/ METAL /GI /CI /Stoneware/DWC pipe/ masonary Open Duct/ cable tray/ open in air etc. as requred.

3.5 core, 120 sq.mm.

3.5 core, 70sq.mm.

3.5 core, 50sq.mm.

4 core, 16 sq.mm. Al

3 core, 6 sq.mm. Cu ar .xlpe cable

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

3.5 core, 120 sq.mm

3.5 core, 70sq.mm

3.5 core, 50sq.mm

4 core, 16 sq.mm

3 core, 6 sq.mm. Cu ar .xlpe cable

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

150 mm width x 50 mm depth x 1.6 mm thickness

300 mm width x 50 mm depth x 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “bends” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

150 mm width x 50 mm depth x 1.6 mm thickness

300 mm width x 50 mm depth x 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Tee” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

150 mm width x 50 mm depth x 1.6 mm thickness

300 mm width x 50 mm depth x 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Cross member” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

150 mm width x 50 mm depth x 1.6 mm thickness

300 mm width x 50 mm depth x 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Reducer” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

150 mm width x 50 mm depth x 1.6 mm thickness

300 mm width x 50 mm depth x 1.6 mm thickness

Supply & Fixing of factory fabricated pre-galvanized G.I. sheet steel raceway in 1.6mm thickness for bottom & sides and 2/3mm thick top Cover as called for including necessary civil work such as chase cutting in screed, fixing/ jamming the raceway, aligning & levelling and finishing with sand cement plaster.

80mm x 40mm (2mm top Cover)

100mm x 40mm (2mm top Cover)

150mm x 40mm (2mm top Cover)

Supply of Bamboo 8W(1000mm) post top Fixture made of aluminum pipe UV protected pure polyester powder coated black after phosphochromate treatment with aluminum heat sink for effective thermal management, sturdiness & excellent corrosion resistant. Mounting flange of MS sand casting is used at the bottom.PC diffuser cover in opal finish is used for glare free uniform light distribution.High efficiency long life LED module with SMD LED package mounted on MCPCB with lumen efficacy of >67 lm/W with system lumen 536. Powered by built-in, isolated electronic LED driver in ABS housing with APFC (SMPS based constant current supply) with lower THD, Output Short / Open Circuit protection, Over Voltage protection, Surge Voltage protection. CCT 3000, CRI>80, THD<20%, PF>.95, IP65,IK 07 ,Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ. DRIVER SAFETY REQUIREMENT STANDARDS :IS 15885-2-13, TEST REPORT TO BE SUBMITTED; DRIVER PERFORMANCE REQUIREMENTS: IS 16104, TEST REPORT TO BE SUBMITTED; PHOTO BIOLOGICAL SAFETY NORMS: IS 16108, TEST CERTIFICATE TO BE SUBMITTED; CERTIFICATION: LM 79 FOR LUMINAIRE LM 80 FOR LED SOURCE.

Supply of Ruby 25W post top Fixture made of Die-cast aluminum spigot for mounting LED driver and spun aluminum canopy which is painted white inside and Epoxy powder coated matt black finish after phosphochromate treatment.High quality polycarbonate cover is used over LED module to enhance the lumen output & clear acrylic diffuser is used to provide overall glare free light.High efficiency long life LED module with SMD LED package mounted on MCPCB with lumen efficacy of >75 lm/W with system lumen 1900. Powered by integral, isolated electronic LED driver in ABS housing with APFC (SMPS based constant current supply) with lower THD, Output Short / Open Circuit protection, Over Voltage protection, Surge Voltage protection. CCT 3000, CRI>70, THD<10%, PF>.95, IP65, IK07.Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ. DRIVER SAFETY REQUIREMENT STANDARDS :IS 15885-2-13, TEST REPORT TO BE SUBMITTED; DRIVER PERFORMANCE REQUIREMENTS: IS 16104, TEST REPORT TO BE SUBMITTED; PHOTO BIOLOGICAL SAFETY NORMS: IS 16108, TEST CERTIFICATE TO BE SUBMITTED; CERTIFICATION: LM 79 FOR LUMINAIRE LM 80 FOR LED SOURCE.

Supply of 3 mtr. (Octagonal) Street Light Poles including the cost of providing 600mm dia 6 mm thick MS plate welded to the base of the pipe and including digging and including the cost of masonry base pedstal built with 1:3:6 concrete (1 cement, 3 coarse sand and 6 graded stone aggregate 40 mm nominal size) provided with a 200 mm x 150 mm x 100 mm deep looping cable box recessed in the base pedestal/ surface mounted fabricated from 14 SWG MS sheets with hinged gasketted lockable door, terminal block for incoming and outgoing PVCA cables, 16 amps SP MCB, 2 Nos. suitable length 50mm dia PVC pipe for incoming and outgoing cables and including the cost of painting, wiring, in pole from terminal block upto the light fittings with 2 x 2.5 sq.mm copper conductor 1100 volt grade PVC insulated wires alongwith loop earthing with 1 no. 8 SWG GI wire, earth stud etc. complete as required.

Supply, Installation, Testing and Commissioning of 2.5mm Pixel Pitch Active Led Video wall size of min (17.7X9.97) feet, pixel configuration 3-in-1(1 red,1 green,1 blue), pixel density 160,000 pixels/m2 or better, brightness 800 nits (cd/m2) or better, inbuilt power redundancy,viewing angle 160°H, 160°V, refresh rate >3840 Hz or better, color temperature 3000-9500 K, display colors 4.39 trillion (14-bit), Certifications CE, FCC, CB, cTUVus,PSE, Minimum pixel resolution of video wall 2160x1215 or better. Video wall should come with OEM wall mounting arrangement.

Supply, Installation, Testing and Commissioning of 55"4K (3,840 x 2,160), Direct LED Professional Display with 4K resolution, Native Contrast ratio upto 1100:1, Response time 8ms or better, Peak Brightness 500 cd/m² or better, 4K 24/7 Portrait , HDCP 2.2 (HDMI) / RS232 / USB / RJ45 / Wi-Fi with In-Built Bluetooth / 10W Speakers Viewing angle 178 degree or better, Including confidence monitor stand with wheels for display.

Supply, Installation, Testing and Commissioning of 43"4K (3,840 x 2,160), Direct LED Professional Display with 4K resolution, Native Contrast ratio upto 1100:1, Response time 8ms or better, Peak Brightness 500 cd/m² or better, 4K 24/7 Portrait , HDCP 2.2 (HDMI) / RS232 / USB / RJ45 / Wi-Fi with In-Built Bluetooth / 10W Speakers Viewing angle 178 degree or better, Including wall mount bracket.

Supply, Installation, Testing and Commissioning of 2x1 switcher with USB-C, HDMI 2.0 and USB 3.1 ports supporting 4K signal formats (4K UHD @ 60Hz RGB 4:4:4, up to 18 Gbps), secure control Ethernet interface. USB-C connectivity for 4K video, audio, USB 3.1 gen peripherals, LAN Ethernet, control signals and charging up to 100W. The device shall have programmable control system. The device should also work as USB Hub and USB Switcher both. In order to acheive the same functionality, multiple same OEM components can be quoted as per asked minimum specifications.

Supply, Installation, Testing and Commissioning of 4x2 matrix with USB-C, HDMI 2.0 and USB 3.1 ports supporting 4K signal formats (4K UHD @ 60Hz RGB 4:4:4, up to 18 Gbps), secure control Ethernet interface. USB-C connectivity for 4K video, audio, USB 3.1 gen peripherals, LAN Ethernet control signals and charging up to 100W (120W total). The device shall have programmable control system. The device should also work as USB Hub and USB Switcher. In order to acheive the same functionality, multiple components can be quoted as per asked minimum specifications.

Supply, Installation, Testing and Commissioning of Full 4K HDMI 2.0 transmitter with RS-232,IR, Ethernet and Bidirectional 12V remote powering; supports 4K UHD @ 60Hz RGB 4:4:4, up to 18 Gbps, HDCP 2.2.

Supply, Installation, Testing and Commissioning of Full 4K HDMI 2.0 receiver with RS-232, IR, Ethernet and Bidirectional 12V remote powering; supports 4K UHD @ 60Hz RGB 4:4:4, up to 18 Gbps, HDCP 2.2.

Supply, Installation, Testing and Commissioning of 4 input and 4 output Full 4K HDMI 2.0 and HDCP 2.2 standalone matrix with analog audio ports. 4K@60Hz with RGB 4:4:4 colorspace, 18 Gbit/sec bandwidth. RS-232, Ethernet and USB control options, Pixel Accurate Reclocking, Advanced EDID Management. LCD front panel control.

Supply, Installation, Testing and Commissioning of one HDMI input and four HDMI output 4K 4:4:4 HDMI distribution amplifier with built-in EDID Management, HDMI 2.0 signals with or without HDCP encryption.

Supply, Installation, Testing and Commissioning of USB over Category Cable Extender Local & Remote, for most of the USB 3.2 or better devices, Should provide connectivity for a single USB host like computer, media server, codec, etc.Should Extend USB signals up to 330 ft (100 m) over CAT6a/7 (or better) twisted-pair cable using Rx module at speeds up to 5 Gbps. Should be compatible with Windows®, macOS®, or Linux® operating system and no drivers required.

Supply, Installation, Testing and Commissioning of PTZ Camera with the following specification:- (i) The camera sensor should be 1/2.7-inch. Having high quality HD camera with CMOS Sensor or better. (ii) The camera should have an Option of Auto or Manual White Balance. (iii) The camera should have a 20x optical zoom or better (iv) The camera should have a standard Video Output and should support 3G-SDI,HDMI/DVI , IP Based so that Camera can be integrated with standard End Points and USB 3.0 or better (v) The camera should have 55.5 Degree or better field of view. Should support minmum 18 Lux illumination (vi) The camera should have a Pan Rotation Angle of Pan: -130° -130°, Tilt: -30°-90° or better Should have built-in AI feature - Group Framing, Speaker tracking, discussion mode. (vii)The camera should support 1080p@60fps and Should support upto 50 ft distance (viii) It should have at least 1 RJ-45 Port for IP Camera functions. The camera should have an option VISCA/TCP, VISCA/UDP, PELCO-D, PELCO-P, ONVIF, UVC for communication It should have necessary certifications (CE, FCC etc). Proof to be submitted.

Supply, Installation, Testing and Commissioning of secure, high performance control processor. Having ethernet port of 100/1000 Mbps, auto switching, auto negotiating, auto discovery, full/half duplex, industry-standard TCP/IP stack, DHCP, SSL/ TLS/SSH, IEEE 802.1xX, SNMP,HTTPS.Having minimum Memory SDRAM 1 GB, Flash 8 GB, and External Storage Support. External Storage Support (OPTIONAL) . Minimum Control ports of 7no's RELAY OUTPUT, Min 7 no’s I/O port. 1 x Bidirectional RS-232/ 422/485 port. Minimum 2 x Bidirectional RS-232 ports Should have BACnet™ for integration (internal or by additional hardware) with existing building management systems like Centralized HVAC, security fire,Should be able to control the complete programmed system, from the IT laptop or PC.Should comply to CE, UL, FCC. (Additional BIS to be shared if applicable).

Supply, Installation, Testing and Commissioning of 10" Wireless Touch Panel, Resolution 1920x1200 or better. Should support 5 point multi touch. Should have built-in Wifi communications. Should have H.264 or better formats. Brightness: 350 nits (cd/m2). SDRAM: 3 GB or better, Flash: 20 GB or better. Should have built-in Speakers. Continously Charging backup should have atleast 110 hrs or better. Should work on battery minimum 8 hrs without charging the panel.Should be supplied with Docking station and standard accessories.

Supply, Installation, Testing and Commissioning of 10-11 inch Multi‐Touch (iPad) with IPS technology with Liquid Retina display, Resolution:2388x1668-pixel resolution at 264 pixels per inch (ppi), 600 nits brightness. Should be provided with docking station.

Supply, Installation, Testing and Commissioning of 24 port Ethernet switch. Should have minimum 24x 1000Base-T Gigabit Ethernet RJ45 port that provides PoE+. Should have minimum 4x 10 Gigabit Base-X SFP+ ports populated enable use of transceiver modules to connect to a fiber network. Should provide minimum 950W. IGMP Support, LLDP Support.

Supply, Installation, Testing and Commissioning of Wi-Fi Router with Wifi technology- 802.11a Dual Band Gigabit, Wifi Range-Large homes, Number of ethernet ports- (1 WAN and 4 LAN) Gigabit Ethernet ports with auto-sensing technology.

Supply, Installation, Testing and Commissioning of Recorder and streming device Controller Record and stream simultaneously Produce MP4 media or M4A audio files that are compatible with virtually any media player Min 3 HDMI Inputs, Internal/External Storage USB / eSATA upto 1TB, Digital processing 4:2:2, 8-bits per color, Compression H.264/AVC (ITU H.264, ISO/IEC 14496-10) 4:2:0, 8-bit color Encoding profiles: High, Main, Baseline; Encoding levels: 4.1, 4.0, 3.2, 3.1, 3.0; configurable GOP Bit rate 200 kbps to 10 Mbps.

Supply, Installation, Testing and Commissioning of USB-C to USB-C 3 m (9,84 ft) cable. USB Full Featured Type-C for USB 3.1 Gen 1.

Supply, Installation, Testing and Commissioning of 3 m (9.84 ft) Premium High Speed HDMI 2.0b cable.

Supply, Installation, Testing and Commissioning of 15 meter Premium High Speed HDMI 2.0b cable.

Supply, Installation, Testing and Commissioning of Loudspeakers with Drivers 1 x 15" / 1 x 1,4 HF, Frequency range 50 - 19000 Hz, Power capacity programm / peak: 800 / 1600 W , Impedance 8 Ohm , Coverage range (h x v) 75° x 50° HF-horn, rotable;Sensitivity 1 W / 1 m -- 99 dB, SPLmax / 1 m / peak 131 dB. wall/celing mount brackets shall be included complete in all respect with required accesories as directed by Engineer- In- Charge.

Supply, Installation, Testing and Commissioning of Subwoofer with Drivers 1x 18" LF; Fequency range 32 - 160 Hz, Power capacity-programm / peak: 2400 / 4800 W ; Imopedance - 8Ohm, Sensitivity 1 W / 1 m - 96dB Passive ; SPLmax / 1 m / peak 132dB. Complete in all respect with required accesories as directed by Engineer- In- Charge.

Supply, Installation, Testing and Commissioning of Loudspeakers with Drivers 1 x 5" LF / 1 x 0.7" HF ; Frequency range100 - 22000 Hz; Power capacity programm/peak: 100 / 200 W ; Impedance - 6 Ohm; Coverage range (h x v) 110° radial;Sensitivity 1 W / 1 m- 88 dB; SPLmax / 1 m / peak 109 dB wall mount brackets shall be included Complete in all respect with required accesories as directed by Engineer- In- Charge.

Supply, Installation, Testing and Commissioning of stage monitor trapezoidal in shape Loudspeakers with Drivers 1 x 8" LF / 1 x 1" HF, Frequency range -70 - 20000 Hz, Power capacity programm / peak: 400 / 800 W , Impedance-8 Ohm Coverage range (h x v) 90° x 60° HF-horn, rotable, Sensitivity 1 W / 1 m - 95 dB ;SPLmax / 1 m / peak -124 dB, Connectors 4 Speakon, in wooden enclosures wall mount brackets shall be included Complete in all respect with required accesories as directed by Engineer- In- Charge.

Supply installatons, testing commission of SITC of Four Channel amplifier with inbuilt DSP, 1500W @2ohm, 1200W @4 ohm; 1200W @8ohm and 3000W @4Ohm and 2400W@8Ohm in bridge mode; Maximum output voltage 140Vpeak and 45Apeak current; Frequency Response 20Hz-20KHz;S/N Ratio- 110dBA; Crosstalk >70dB@1Khz;THD+N < 0.2%; Slew Rate->50V/microSec; Damping Factor >500@ 20-100Hz; A/D and D/A Converters of 24bit/48KHz; DSP Inbuilt Preset Memory; Crossover Filters - linear phase (FIR), Butterworth, Linkwitz-Riley, Bessel: 6 dB/oct to 48 dB/oct (IIR);Input Equalizers - Raised-cosine, custom FiR, parametric iiR: peaking, hi/lo-shelving, all-pass, band-pass, band-stop, hi/lo-pass; Output Equalizer ; Limiters - P TruePower™, RMS voltage, RMS current, Peak limiter; Audio signal input 1 x 12 pin Phoenix MC 1.5/12-ST-3.81 - Signal input – MAIN; Loudspeakers 1 x 8 pin Phoenix DFK-PC 4/8-G-7.62 - Signal output; With separate input and Output DSP and DANTE ready.

Supply, Installation, Testing and Commissioning of Four Channel amplifier with inbuilt DSP, 380W @2ohm , 280W @4 ohm; 280W @8ohm ; 780W @4Ohm and 580W@8Ohm in bridge mode; Maximum output voltage 70Vpeak and 33Apeak current; Frequency Response 20Hz-20KHz;S/N Ratio- 104dBA; Crosstalk >70dB@1Khz;THD+N < 0.1%; Slew Rate-50V/microSec; Damping Factor >500@ 20-100Hz; A/D and D/A Converters of 24bit/48KHz; DSP Inbuilt Preset Memory; Crossover Filters - linear phase (FIR), Butterworth, Linkwitz-Riley, Bessel: 6 dB/oct to 48 dB/oct (IIR);Input Equalizers - Raised-cosine, custom FiR, parametric iiR: peaking, hi/lo-shelving, all-pass, band-pass, band-stop, hi/lo-pass; Output Equalizer ; Limiters - P TruePower™, RMS voltage, RMS current, Peak limiter; and with speaker presets, Separate input and output DSP , 4 input DANTE input Ready.

Supply, Installation, Testing and Commissioning of Digital Wireless Dual Channel Receiver with 2 Handheld Mic & Network connectivity, Type : Dynamic, Audio Frequency Range – 470-937 MHz, 24 bit Digital Audio, Dual Channel Receiver with following specifications:- (i) Dynamic Range - 120 dB or better (ii) Frequency Response : 20 to 20,000 Hz (iii) Polar Pattern : Cardioid (iv) Support upto 96 compatible channels (v) Switching Bandwidth - 44 MHz or better (vi) Frequency Auto Scan Functionality (vii) Range – 300 ft or more (viii) RF Transmitter Output : 1mW/10 mW, switchable (ix) Frequency and Power Lock out (x) THD – <0.02% (xi) Latency – 3.2ms (xii) Sensitivity - -97 dBm (xiii) Should include 2 rechargeable batteries and charger with 2 slots for Handheld transmitter (xiv) Battery Life : 8 hours or more.

Supply, Installation, Testing and Commissioning of • Digital Wireless Dual Channel Receiver with 2 Lapel Mic & Network connectivity with following specifications:- (i) Type : Condenser (ii) Audio Frequency Range – 470-937 MHz (iii) 24 bit Digital Audio (iv) Dual Channel Receiver (v) Dynamic Range - 120 dB or better (vi) Frequency Response : 20 to 20,000 Hz (vii) Polar Pattern : Omnidirectional (viii) Support upto 96 compatible channels (ix) Switching Bandwidth - 44 MHz or better (x) Frequency Auto Scan Functionality (xi) Range – 300 ft or more (xii) RF Transmitter Output : 1mW/10 mW, switchable (xiii) Frequency and Power Lock out (xiv) THD – <0.02% (xv) Should include 2 rechargeable batteries and charger with 2 slots for Bodypack transmitter (xvi) Battery Life : 8 hours or more.

Supply, Installation, Testing and Commissioning of Dual Channel Receiver with 2 Earset Mic & Network connectivity • Type : Condenser • Audio Frequency Range – 470-937 MHz • 24 bit Digital Audio • Dual Channel Receiver • Dynamic Range - 120 dB or better • Frequency Response : 20 to 20,000 Hz • Polar Pattern : Omnidirectional • Support upto 96 compatible channels • Switching Bandwidth - 44 MHz or better • Frequency Auto Scan Functionality • Range – 300 ft or more • RF Transmitter Output : 1mW/10 mW, switchable • Frequency and Power Lock out • THD – <0.02% • Latency – 3.2ms • Sensitivity - 41.0 dB V/Pa • MAX SPL : 107dB • Equivalent Output Noise : 24.9 dB or less • Signal to Noise Ratio : 60.0 dB • Should include 2 rechargeable batteries and charger with 2 slots for Bodypack transmitter • Battery Life : 8 hours or more.

Supply, installation, testing and commissioning of 18" Gooseneck Microphone with Shock Mount and Mute Switch Frequency Response - 50 to 17,000 Hz with following specifications:- (i) Output Impedance (at 1,000 Hz) - Rated at 150 Ohm (180 Ohm actual) (ii) Open Circuit Sensitivity (At 1 kHz) - 33.5 dBV (21.1 mV) (iii) Maximum SPL (1kHz at 1% THD, 1 kOhm load) – 124.2 dB (iv) Equivalent Output Noise (A-weighted) - 28.0 dB SPL (v) Signal to Noise Ratio (at 94 dB SPL) - 66.0 dB (vi) Dynamic Range with 1 kOhm load – 96.2 dB (vii) Common Mode Rejection - 45.0 dB minimum (viii) Mute Switch Attenuation - 50.0 dB minimum (ix) Preamplifier Output Clipping Level (1% THD) - –6.0 dBV (0.5 V).

Supply, Installation, Testing and Commissioning of Antenna Splitter and Power Distribution System for receivers, 4-way active antenna splitter plus cascade port, different frequency versions available, external power supply. RF Frequency Range: 174 to 1805 MHz Gain Input to any output port: -1 to +1 dB with all required cables and accessories as per site requirement.

Supply, installation, testing and commissioning of 100 feet antenna cables, 50 Ohms.

Supply, Installation, Testing and Commissioning of Wired Vocal Microphone with following specifications:- (i) Type : Dynamic (ii) Frequency Response : 50 to 15,000 Hz (iii) Polar Pattern : Cardioid (iv) Sensitivity (at 1,000 Hz Open Circuit Voltage) : –54.5 dBV/Pa (1.85 mV) 1 Pa = 94 dB SPL (v) Impedance : Rated impedance is 150Ω (300Ω actual) for connection to microphone inputs rated low impedance (vi) Polarity : Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3. (vii) Case : Dark gray, enamel-painted, die cast metal; matte-finished, silver colored, spherical steel mesh grille (viii) Connector : Three-pin professional audio connector (male XLR type).

Supply, Installation, Testing and Commissioning of 16 in 8 out Analog I/O Digital stagebox as the same OEM and compatible with offered Digital Mixer. Shall offer pre-amp control and a redundant mode connection complete in all respect with required accesories as directed by Engineer- In- Charge.

Supply, Installation, Testing and Commissioning of Digital Audio Mixer with 32-40 input Digital Mixing Console and USB Interface and 32 programmable Preamps, 24 or better Motorized Faders, 40 DSP input channels (32 mono inputs and 4 stereo channels/returns), Channel LCD's, FireWire/USB Audio Interface and iPad/iPhone* Remote Control include I/O Box with 16 Remote-Controllable Preamps, Including Mini Stagebox 16 or 32 Channel combine high-quality components with a streamlined design, making it easy to add multiple channels of remote- controlled I/O toDigital mixing console complete in all respect with required accesories as directed by Engineer- In- Charge.

Supply, Installation, Testing and Commissioning of Dante Digital Audio I/O card for offered digital mixer. Shall offer gigabit redundant Ethernet connection ports for bidirectional audio upto 64x64 channels.

Supply, Installation, Testing and Commissioning of custom Floor Box for stage with 4 power, 4 XLR input, 4 LAN port complete in all respect with required accesories as directed by Engineer- In- Charge.

Supply, Installation, Testing and Commissioning of minimum 14 AWG or thicker Speaker Cable with copper conductors and PVC Jacket complete in all respect with required accesories as directed by Engineer- In- Charge.

Supply, Installation, Testing and Commissioning of 24 AWG or better CAT6A STP cablesupport 10 gig data STP cable complete in all respect with required accesories as directed by Engineer- In- Charge.

Supply, Installation, Testing and Commissioning of Shielded microphone cable. 2 core + Shield, 23 AWG or better complete in all respect with required accesories as directed by Engineer- In- Charge.

Supply, Installation, Testing and Commissioning of 42 U Equipment Rack, Locakable front glass door, cooling facility, internal wiring, front glass door, heat dessipation fans, movement wheels, power distribution units & equipment shelves as required, fully welded construction for strength. Extra-wide rackrail for cable pass-throughs to facilitate front-to-rear cabling complete in all respect with required accesories as desired by Engineer- In- Charge.

Supply, Installation, Testing and Commissioning of Smart metallic podium with options for gooseneck mic, separate drawer for documents, fitted with i7 12 Gen PC (8GB RAM, 500GB SSD, inbuilt Wi-Fi enabled, and licensed Window 10 Professional pre loaded with 4 USB port, Licenced microsoft word, antivirus and other required softwares for functioning of auditorium softwares, HDMI port and audio port, fitted with 23” Interactive Pen Touch Monitor (Wacom or Equv) for Live annotation with tilt motorized mechanisum. FHD / UHD Resolution. Brightness: 250 cd/m2, contrast ratio: 1000:1 or better. Viewing angle : 178°(v) 178°(h) or better. Input: 1x HDMI. USB Interface. To be supplied with complete accessories wireless keyboard and wireless mouse with required capacity UPS complete in all respect with required accesories as desired by Engineer- In- Charge. Podium design with logo has to be approved by EIC before supply.

Supply, Installation, Testing and Commissioning of LED Par Lights with Lamp : 3 Watt x 54 RGBW and with channel : 6 or more DMX; Power consumption : 110 W or better, 240volt. Housing CRC sheet, Color Black, Function: strobe, dimming, sound active and Master slave. Focusing Front/Back/Rotary Knob, 2 mtr. 3 core wire , plug top. Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of LED profile light Lamp with 200 Watt or better; 2 or better DMX channel protection grade over heating & high voltage. • Focus : Manual Focus e Beam Angle : 19° Control : DMX, Autorun and Master/Slave Shutter arrangements : Beam shapping shutter. Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of LED Fersnal light with Lamp : High quality 180W LED Fresnel light used as a Key light, Back light, Fill light with dimming, spot & flood focus versions for creating various effects for multiple applications with specifications as below. Lamp power - 180W COB LED Power SITC - 100-240 AC, 50/60 Hz Power cable - 3 core 1 sq. mm. copper PVC insulated Color Temperature: 3200K Control : DMX512 / Manual Spot - Flood focus adjustment. Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of LED Flasher Bar with power consumption of 100 W or better; Lamp : 18 RGBW 10 Watt, Channel : 7 DMX; Control : DMX, Housing CRC sheet metal Holder 2 Nost, 2 mtr 3 core copper wire 3 pin plug top. Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of 300W LED Moving Head Light used as a Special Effect Light by Integrating three features - Beam, Spot, & Wash effect with high- contrast gobo projection etc., for entertainment lighting. with below specifications: - Source : 1 x 300W LED e Power SITC : 100 - 240v AC, 50 - 60Hz. Operation Modes : DMX512, Master / Slave, Sound active. e Beam Angle : 1°/3°/6.5° (with beam reducer), 2°/6°/13°/20° (with zoom lens), Spot Angle : Fix Gobo: 9°-18°, Rotating Gobo: 7.5°-+13° (with zoom lens) , Wash Angle : 12°~23° e Pan/Tilt Angle : 540°/ 240° (16 bit) DMX Channels : 16/19 channel e Color Wheel : 7 fixed colors plus white with rainbow effect Gobo Wheel : 1 static gobo wheel with 9 fixed gobos plus open and 1 rotating gobo wheel with 7 gobos plus open ¢ Prism : 6 facet prism, rotation in both dirct.Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of High quality LED PARCAN Light used for dance hall, architectural and stage lighting with below specifications: Lamp power - 100W LED Power SITC - 100-240 AC, 50/60 Hz Channels: 2 channel DMX 512 Control: Manual, DMX Color Temperature: 3000K CRI > 90 Function: Dimming, Strobe Dimming: 0-100% Beam Angle - 9/15/20° Protection rating - IP20. Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of "C" clamp with safety locking chain, duly powder coated in black matt texture finish. Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of Light controller with 20 or more channel Double Preset/40 or more channels Single preset(WIDE);with 2 or more output channels,48 registers or better (asignable with scane memories or chase)+24 registers or better for the immediate modification of the channels,12 pages or more of registers (total 288 scene memories),24 or more programmable chase (level or on/off) with chase level independent. Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of DMX Data Splitter: 1 x IN and 12 x Out or more DMX-512 Data Splitter, suitable both for Dimmer & Intelligent Lights.Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of Follow spot light 1250 watt long double ended color temperature : 6000K DMX channels：4 channels dimmer/flash: dual patches dimming,1-10 flashes/s,speed adjustable, iris: linear zoom in & zoom out, color wheel: 5 colors+ white/with rainbow effect, speed adjustable, color temperature wheel: 2 color temperature rectify filters. Complete in all respect as desierd by the Engineer in charge of work at site.

Supply, Installation, Testing and Commissioning of 2 core shilded DMX control cable for lighting. Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of Inter connection XLR Box- DMX Data patch cables, using 2-core Cu.Cond.Lap sheilding, suitable for RS485 / DMX data ; for interlinking Intelligent Lighting Fixtures & Dimmer(s) to DMX Splitter(s) & to control desk - to be laid in PVC conduits (to be terminated with supplied XLR connectors). Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of 2.5sqmm x 3 core cable (Incoil/National).Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of Socket box 4'x4' with Power junction BOX multi socket lor lighting power. Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of Side Light Ladder of 25mm x 50mm M.S.tube size (6'x2').Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of Stage suspension Grid by providing & fixing MS suspension grid system over stage for hanging stage services made of 2 nos 40x40x5mm MS angles welded back to back with 50x12x12mm thk studs as MS spacers sandwiched between the MS angles so as to maintain 12mm gap between MS angles, the welded angles to be placed @ 1200mm c/c in one direction and 40x5mm thick MS Tee @ 600mm c/c in other direction. The MS grid to be suspended from the roof structure by means of MS flat suspender of 50x6mm thick MS flats @ 1200mm c/c in both directions. All MS members to be painted with a coat of red oxide primer & 2 or more coats of black enamel paint. All complete as per Architect or Architect's representative.

Supply, Installation, Testing and Commissioning of B class 50 mm dia M.S. pipe painted black hanged from the grid by means of MS flat to act as lighting bars. etc. complete as reqd.Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of Main curtain made out of Velvet curtain (480 to 500 gram in 1 mtr) cloth with horizontal sliding arrangement complete with fixing railing track,fixing brackets,runner,master runner,3mm rope wire,1HP Crompton Motor,drum with groove cutting,pulleys,2 No air breaker switch for reverse & forward, 2 No air micro switch for auto stop,3 No push button for Open/Stop/Close position the curtain should be droped to half area,when in closed position and minimum overlap at the centre should be 900mm and curtain should be stitched in double gathering.Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of back curtain made out of glazed cotton cloth with horizontal sliding arrangement complete with fixing railing track,fixing bracket,runner,master runner,3mm rope wire,1HP Crompton Motor,drum with groove cutting,pulleys,2 No air bracker switch for reverce & forward,02 No.air microswitch for auto stop,3 No push button for Open/Stop/Close position the curtain should be droped to half area,when inclosed position and minimum overlap at the centre should be 900mm and curtain should be stitched in One & half gathering. Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of Stage Curtain control box well designed and engineered Wall mount 6 feeder motor control centre panel & Remote control panel with emergency trip & necessary meterings and contactors and relays to control the motors system for curtains.(MCCP/RCP -6). Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of motorised winch operated bars of 300 Kg capacity, Bars are suspended using steel wire rope guided through 1,2,3 and 4 set of divertor Pullies and supported at every 3-4 mtr. The Existing GI pipe for Light and Set bars are then welded to the Winch bar. The Light Bar winches should have necessary Cable Retracting arrangement to be collected in cable basket fixed on the Motorised Bar. Complete in all respect and to be approved by Architect and his representative.

Supply, Installation, Testing and Commissioning of COB based recessed downlight luminaire with system power: 12 W, Luminous flux of luminaire 1200 lm, Colour temperature of 4000 K, Neutral white, SDCM 3, CRI > 80, 230 V constant current driver, 70% of luminous flux after 50,000 operating hours; Energy efficient LEDs, Direct light emission, Luminaire housing in aluminium, Polyester powder white coloured coat applied over a 5- stage pre-treatment, Clear glass cover, beam angle of 38°, ZHLS (ZERO HALOGEN LOW SMOKE) wiring, External electronic control gear, Protection class II, IP 40, Ø = 114mm, DA(Ø) = 108mm, H = 110mm.

Supply, Installation, Testing and Commissioning of Recessed with Trim luminaire with HPE (High-Performance Efficiency) LED (Light Emitting Diode) system power: 12W/4ft, Luminous flux of luminaire 1320 lm, Colour temperature of 4000 K, Neutral white, CRI > 80, 230 V constant current driver, 70 % of luminous flux after 50,000 operating hours, Energy-efficient LEDs, Direct light emission, Luminaire profile in anodised aluminium, snap-fit prismatic diffuser for homogenous light distribution, ZHLS (ZERO HALOGEN LOW SMOKE) internal wiring, Electronic control gear, Protection class I, IP 40, L = 1000 mm, B = 64 mm, H = 64 mm, B (ET) = 52mm.

Supply, Installation, Testing and Commissioning of LED recessed luminaire with LED(Light Emitting Diode) system power: 25W, the colour temperature of 4000K, neutral white, 230V constant current driver, 70% of luminous flux after 50,000 operating hours, energy-efficient LEDs, CRI>80, the luminous flux of 3500 lm, Electronic control driver, direct light emission, Sheet Metal frame, polyester white powder coat applied over a 5-stage pre-treatment, opal diffuser for glare-free uniform light. Protection class I, IP40, MacAdam 3, T.H.D≤ 10%, driver efficiency ≥ 88%, surge protection of 2.5kV, L = 595mm, B = 595mm, H = 70mm.

Supply, Installation, Testing and Commissioning of LED strip with aluminium profile and 60 LEDs per meter, 10W per Meter, 4000K, 2835 SMD package with thermal tape of high thermal convection factor, beam angle of 120°, MacAdum 5, constant voltage driving circuit, L = 1000mm, H = 10mm, B = 1.4mm.

Providing and fixing of Step Lighting Voltage 240 V Color White, Grey, Black Base White, Poly Carbonate, FR Grade,UV stabilized Material grade Poly Carbonate Uv stabilized & Fr grade. complete to the satisfaction of Engineer –in-charge.

Providing and fixing of LED Exit signage Voltage 240 V and battery backup Poly Carbonate, FR Grade,UV stabilized Material grade Poly Carbonate Uv stabilized & Fr grade. complete to the satisfaction of Engineer –in-charge.

Design, manufacture, supply, installation, testing and commissioning of following Utility LT panels suitable for 415 V, 3 phase, 4 wire, 50 Hz power distribution system. The panel shall be Indoor, free standing, floor mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type compartmentalized design fabricated out of 2mm thick CRCA sheet steel for Load bearing members and 1.6 mm thick for non-load bearing members, complete with color coded, heat shrinkable PVC insulated, aluminum bus bars and separate earth bus bar of adequate cross section through out the length of the panel. The incoming and outgoing feeders shall be accommodated in a fully segregated, modular multitier arrangement with adequate size and distinct cable alley, bus bar alley/chamber (form-3b Construction). The panel shall be complete with name plate, earthing, numbering, danger plate etc. as required and as per specifications and drawings. The panel shall withstand the fault level of as indicated else where or shown in Single Line Diagrams.

General Notes: Applicable for all Panels: (a) All Panels with incomer rating 400A or above shall be as per IEC61439 (part-1 & 2) TTA and panels with below 400A rating incomer shall be IEC61439 PTTA type. (b) Degree of protection as per IEC60529 for 1 sec. (c) The BOQ shall be read in conjunction with general notes, specification, single line diagram & boq. Incase of any discrepancy between General notes, SLD, specification & BOQ, the same shall be brought to the notice of Client/Consultant before quoting the rates, otherwise stringent condition shall be deemed to have been considered. (d) Fault current wherever mentioned shall be Ics=Icu=Icw for 1 sec for ACBS & Ics=Icu for 1 sec for MCCBS. (e) All MCCB shall be provided with door interlocked rotary handle and ON, OFF, TRIP Indicating lamp protected with 2A, SP MCBs . The MCCB upto 250A shall be with thermal magnetic releases and above 250A shall be with micro processor based releases. (f) All Microprocessors based MCCBs shall be provided with inbuilt O/C, S/C and E/F releases & thermal magnetic based shall be with inbuilt O/C & S/C releaseswith earth fault module CBCT. (g) All feeder doors shall have pad locking arrangement. (h) All TP feeders shall have solid isolable neutral link. (j) All Star/Delta starter to be provided with Motor duty MCCB, AC-3 duty contactor, over load relay with single phase preventor, digital ammater, suitable ratio CL-1, 5VA cast resin CTS, start/stop push button & on/off/trip indicating lamps etc. All Switchgears should by type-2 coordinated. All starters shall have BMS compatability. (k) All DOL starter to be provided with Motor Protection Circuit Beaker MPCB, AC-3 duty contactor, over load relay with single phase preventor, digital ammater, suitable ratio CL-1, 5VA cast resin CTS, start/stop push button & on/off/trip indicating lamps etc. All Switchgears should by type-2 coordinated. All starters shall have BMS compatability.

(l) The Automatic Power Factor capacitor Panel shall be composed of the minimum followings:- (i) Shunt capacitor (440v) with damping reactor. (ii) Discharge reactor (iii) Thysistar Switching Module (iv) Fuse for Capacitor current protection. (v) APFC Relay/Controller (vi) Control/Monitoring/Measurement equipment.

(m) The rating shall be as per IEC 61921. The degree of protection shall be as per IEC 60529. (n) All ACB's shall be provided with Breaker Control Switch (BCS) having lost motion device. (o) All ACBs shall be provided with O/C, S/C and E/F releases. (p) Bus Coupler shall be provided without releases but with on & off indicating lamps. (q) Spare contacts of ACB/Relays/Contactor etc. shall be wired upto terminal block. (r) All Energy meters are digital type & with RS-485 port for communication. (s) Bus bar chamber shall be kept at top of the all panels. (t) Internal wiring of panel shall be with size 2.5sqmm Flexible Copper Conductor for CT circuit and control wiring with 1.5 sqmm. (u) All Lift Panels transport section should not be more then 1000 mm. (v) In soft starter Vender should supply power contactor with aux. Contactor & All necessary accessories required etc. (As per BOQ & specification) (w) All indicating light shall be LED type . (x) Each vertical section of floor mounted panel shall have independent base frame (75mm x 40mm) size made out of 3 mm sheet steel (LT Panel & DG Panel). (y) All the makes shall be as per approved make list only. (z) Wherever only voltmeter & ammeter are required, the same may be provided in combined meter suitable for both parameter.

(aa) Space heater shall be provided in each cable alley. (ab) All links/drops for ACB/MCCB shall be designed for full rated current of ACB/MCCB rating at same current density of Main Bus Bar. (ac) Arch flash Protection shall be in Cable allay & busbar Chember. (ad) Gas flooding system of panel will be the part of Panel Manufacturer and furher Necessary Co-ordination shall be done by the Panel Manufacturer / Vendor with the vendor of "Gas flooding system" for fire protection, for making suitable provisions in the panels, at the Design stage, Manufacturing stage, stage of testing at works & stage of commissioning at site. (ae) All LT panels & Distribution Boards shall be provided with TVSS (SPDs). Panel vendor/Manufacturers shall Co-ordinate with SPD Vendor for the calculation, supply and installation for the same (SPDs). (af) All outgoing feeders of Main LT Panel cum Syn. Panel to be provided with dual source energy meter. (ag) All CTs and PTs shall be cast resin type. (ah) The list of the panel incorporating the above general notes as given above : (aj) Single Line of the Panels is attached for reference -

ELECTRICAL PANEL Ics = 35KA Incomer:- 1 No. Incomer 200Amps 4P MCCB microprocessor releases for O/C, S/C, 3 Nos. phase indicating lamps to show the incoming power with control 2A TP MCB,and 1 no. digital multifunction meter with matching cast resin CT's. Bus Bar One set of TPN, AL. bus bar rated 250Amps (after considering necessary deratings of 80%) for phases and neutral for half capacity of phases. The outgoing feeders are as follows :- 1 Nos. 125A 4P feeder having one no. 125A 4P MCCB. 2 Nos. 100A 4P feeder having one no. 100A 4P MCCB. 4 Nos. 63Amps 4P feeders each having one number 63 Amps 4P MCB. 3 Nos. 40Amps 4P feeders each having one number 40 Amps 4P MCB. 1 No. 32Amps 4P feeder having one number 32 Amps 4P MCB. 1 No. 25Amps DP feeder having one number 25 Amps 4P MCB. 1 set of complete wiring ELECTRICAL PANEL Ics = 35KA as describe above and shown in SLD.

UPS INPUT PANEL Ics = 35KA, Design and general specifications of panel all as specified under Item No. 249 above with following:- Incomer:- 1 No. Incomer 100Amps 4P MCCB TM releases for O/C, S/C, 3 Nos. phase indicating lamps to show the incoming power with control 2A TP MCB,and 1 no. digital multifunction meter with matching cast resin CT's. Bus Bar One set of TPN, AL. bus bar rated 200Amps (after considering necessary deratings of 80%) for phases and neutral for half capacity of phases. The outgoing feeders are as follows :- 2Nos. 80A TP feeders having one nos. 80A TPN MCCB with isolable neutral, microprocessor based, Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup protection.and Digital flush type class-1.0 accuracy multifunction meter showing V, A, PF, KVAR , KWH etc. along with current transformers of 80/5A ratio, 15 VA Class 1.0 metering. 1 set of complete wiring UPS INPUT PANEL Ics = 35KA as describe above and shown in SLD.

UPS 0UTPUT PANEL Ics = 35KA, Design and general specifications of panel complete all as specified unde Item No. 256 above with the following:- Incomer:- 2 No. Incomer 80Amps 4P MCCB TM releases for O/C, S/C, 3 Nos. phase indicating lamps to show the incoming power with control 2A TP MCB,and 1 no. digital multifunction meter with matching cast resin CT's. Bus Bar One set of TP+2N, AL. bus bar rated 200Amps (after considering necessary deratings of 80%) for phases and neutral for half capacity of phases. The outgoing feeders are as follows :- 2Nos. 63Amps 4P feeders each having one number 63 Amps 4P MCB. 4Nos. 40Amps 4P feeders each having one number 40Amps 4P MCB. 4Nos. 32Amps DP feeders each having one number 32 Amps DP MCB. 1 set of complete wiring UPS OUTPUT PANEL Ics = 35KA as describe above and shown in SLD.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supply, installation, testing and commissioning of following sizes of GI/ Copper strip/wire clamped to walls, cable trays, bus ducts, cables in recess or surface etc for equipment/ System earthing complete as required including inter connection between length at joints, all fixing accessories such as Earth bar, saddles, clamps, lugs etc and other fixing hardware material as required for proper installation.

Providing and fixing 25 mm X 5 mm G.I. earth strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Providing, fixing and termination of 1C x 6 mm sqmm cu unarmoured cable

Providing, fixing and termination of 1C x 16 mm sqmm cu unarmoured cable

Providing, fixing and termination of 1C x 25 mm sqmm cu unarmoured cable

Providing, fixing and termination of Earthing BOX

Providing, fixing and termination of 1C x 35 mm sqmm cu unarmoured cable for UPS input /output panel

Supplying and drawing of UTP 4 pair CAT 6 LAN cable in the existing surface / recessed steel / PVC conduite as required (For CCTV & IT Networking).

1 run of cable

2 run of cable

3 run of cable

Supply, Installation, Testing & Commissioning of Category 6 RJ45 Unshielded Modular Jack, box & face plate ISO/IEC 11801:2nd edition, EN 50173-1, ANSI/TIA/EIA 568-C.2 Category 6, IEC 60603-7, Universal 110 Impact Tool & Tooless (Both) Termination, Min. 250Mhz Bandwidth, Without any OEM Proprietary Tool Termination for Camera at user end. (For CCTV & IT Networking)

Supply, Installation, Testing & Commissioning of loaded 24 port CAT 6 UTP, Transparent shutter jack panel, 1U height, UL-94V-0, Black with cable support bar, clear label marks and earthing plug for CAT6 cable termination at rack end.

SITC of CAT6 UTP 26 AWG Patch Cord - 1 mtr with cross separator , Manufactured from stranded wires for longer flex-life , Minimum length of 1m, and maximum length of 5m Conforming to the following standards like Smoke density: Series IEC 61034 / IEC 61034-2, EN 61034-2, IEC 60754/IEC 60754-2, EN 60754-2, IEC 60332-1/60332-1-2, UL VW-1 with tensile strength >50N, Number of Insertion upto 2500 Duty Cycle

SITC of CAT6 UTP 26 AWG Patch Cord -2 mtr with cross separator , Manufactured from stranded wires for longer flex-life , Minimum length of 1m, and maximum length of 5m Conforming to the following standards like Smoke density: Series IEC 61034 / IEC 61034-2, EN 61034-2, IEC 60754/IEC 60754-2, EN 60754-2, IEC 60332-1/60332-1-2, UL VW-1 with tensile strength >50N, Number of Insertion upto 2500 Duty Cycle

Supply, Installation, Testing & Commissioning of 1, 2 and 4 port Style (Square) Keystone-Type Shuttered Faceplates for I/O fixing at user side.

Supply, Installation, Testing & Commissioning of 4MP IP Network TDN Low-Light IR Vari Focal Lens Dome Camera, 1/3" CMOS or better, 4MP (2560 x 1440) @ 25fps or better, triple stream at various resolution up to 25fps, Min. Illumination required 0.005 lux (color), 0 Lux IR On, Inbuilt Smart IR with upto 50m IR distance, ICR (Infrared Cut Filter) 120dB True WDR, S/N Ratio 50db, Shutter Speed 1/5 - 1/100,000s; Adavance Video Compression technology such as H.265, H.264 & MJPEG , VF Lens 2.8 to 12mm Motorized Focus & Zoom (MFZ), Field of View FoV H:90° to 30°, BLC, HLC, WDR, 3DNR, White Balance - Auto/Indoor/Outdoor/Manual, Minimum Edge Video Analytics : Video Motion Detection, Tampering, Video Exception Scence Change & Video Blur, Intrusion, Line Crossing, One Way Audio, Inbuilt Mic, G.711A/G.711U, 4 Privacy Mask, 8 Region Of Intreset, HTTPS, IP Filter, TLS1.2, AES-128/256, SSH/Telnet closed, 256GB SD card support, PoE (802.3 af) and 12V DC, Max 9W, IP 67 & Ik10, Having Operating temp range : –30°C to 60° C, Reletive Humidity up to 90% NC, Certifications: ONVIF Profile S/G/T compliant, Safety (IEC 60950-1, IS 13252-Part1), EN 55035, FCC Part 15, EN 55032 & RoHS (IEC 62321) compliant.

Supply, Installation, Testing & Commissioning of 4MP IP Network TDN Low-Light IR Vari Focal Lens Bullet Camera, 1/3" CMOS or better, 4MP (2560 x 1440) @ 25fps or better, triple stream at various resolution up to 25fps, Min. Illumination required 0.005 lux (color), 0 Lux IR On, Inbuilt Smart IR with upto 50m IR distance, ICR (Infrared Cut Filter) 120dB True WDR, S/N Ratio 50db, Shutter Speed 1/5 - 1/100,000s; Adavance Video Compression technology such as H.265, H.264 & MJPEG , VF Lens 2.8 to 12mm Motorized Focus & Zoom (MFZ), Field of View FoV H:90° to 30°, BLC, HLC, WDR, 3DNR, White Balance - Auto/Indoor/Outdoor/Manual, Minimum Edge Video Analytics : Video Motion Detection, Tampering, Video Exception Scence Change & Video Blur, Intrusion, Line Crossing, One Way Audio, G.711A/G.711U, 4 Privacy Mask, 8 Region Of Intreset, HTTPS, IP Filter, TLS1.2, AES-128/256, SSH/Telnet closed, 256GB SD card support, PoE (802.3 af) and 12V DC, Max 9W, IP 67 & Ik10, Having Operating temp range : –30°C to 60° C, Reletive Humidity up to 90% NC, Certifications: ONVIF Profile S/G/T compliant, Safety (IEC 60950-1, IS 13252-Part1), EN 55035, FCC Part 15, EN 55032 & RoHS (IEC 62321) compliant.

Supply, installation, testing and commissioning of IP N/W TDN Low-Light IR PTZ Camera, 1/3'' CMOS sensor, 4 MP resolution @ 25fps or better, varifocal 4.5 - 135 mm 30x lens, Auto Iris, Day Night cameras, Deofger, Electronic image stablization, Vandal Proof & Motion detection, Internal / External illumination range upto 100m IR diatance, POE, (high resolution cameras / 4CIF) ONVIF compliant complete with IP 68 Dome Housing, Connectors, Lens, Camera Mounts, Power Supply, I/O and all Ancillary Equipment & all accessories.

Supply, installation, testing and commissioning of Joystick complete with all accessories as required.

Supply , Installation , Testing and commissioning of 24 Channel NVR (Network Vedio Recorder), for recording upto 24CH @ 1080P with 08 nos. SATA HDDs minimum 80TB storage or more, 25fps , H.265/H.264/MJPEG/MPEG4 codec decoding, Front Control Pannel with LEDs Indication for HDDs Status, Power, 3 nos. USB, Onvif S, RAID 1/5, NTP & Daylight saving, iPhone; Audio IN/Out 3.5mm, Display Ports 2 HDMI & 01 VGA, On Screen Display Date Time & Camera Name, Supports Edge VA from Cameras Video Motion Detection, Video Loss, Camera Tamering, Intrusion, Loitering, System Alarm min Alarm In/Out, Disk Failure, Full, iPad; Android based Mobile clients, Video Export feature on USB, Search Mode: Time/Date; Alarm; Motion Detection (MD); Exact Search (accurate to a second); Smart Search, 16CH sync playback, 2 x LAN, N+1 Failover, 16 POE/POE+ Ports, Alarm Input (16 nos.), Alarm Output (6 nos.), 400Mbps throughput, Operating Temperature –10°C to 55°CCertification : CE, FCC, UL, RoHS & NDAA Section 889 Compliant including fixing accessories and cable termination with required connectors/Jack, complete in all as directed by Engineer in-Charge.

Supply, Installation, Testing & Commissioning of 8TB Surviellance Hard Disk.

Supply, Installation, Testing and Commissioning of Full HD 55" LED Professional Display Panel.

Supply, Installation, Testing & Commissioning of L2+ managed industrial PoE switch with 10*10/100/1000M RJ45 ports and 4*100/1000M uplink SFP slot ports, Port 1-8 can support IEEE802.3af/at PoE. Support DC dual power supply input and DIN rail mounting. Switching capaticy of 256 Gbps, forwarding performance 20.83 Mpps, having 8 x 10/100/1000BASE-T PoE-plus(RJ45) with maximum PoE output power is 120W(at-240W). , with 2*10/100/1000Base-T uplink RJ45 ports 4*100/1000Base-X uplink SFP slot ports., 8K MAC address. Should have Static Routing , system logging, Telnet, SSH, SNMP, Network Time Protocol (NTP), and IPv6 features from day 1.

Supply, Installation, Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7-3770 Processor (8M Cache, up to 3.90 GHz); RAM: 8GB (1x8GB) Non-ECC DDR3 1600MHz ; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit or latest.

Supply, Installation, Testing & Commissioning of loaded 24 port CAT 6 UTP, Transparent shutter jack panel, 1U height, UL-94V-0, Black with cable support bar, clear label marks and earthing plug for CAT6 cable termination at rack end.

SITC of CAT6 UTP 26 AWG Patch Cord - 1 mtr with cross separator , Manufactured from stranded wires for longer flex-life , Minimum length of 1m, and maximum length of 5m Conforming to the following standards like Smoke density: Series IEC 61034 / IEC 61034-2, EN 61034-2, IEC 60754/IEC 60754-2, EN 60754-2, IEC 60332-1/60332-1-2, UL VW-1 with tensile strength >50N, Number of Insertion upto 2500 Duty Cycle

SITC of CAT6 UTP 26 AWG Patch Cord -2 mtr with cross separator , Manufactured from stranded wires for longer flex-life , Minimum length of 1m, and maximum length of 5m Conforming to the following standards like Smoke density: Series IEC 61034 / IEC 61034-2, EN 61034-2, IEC 60754/IEC 60754-2, EN 60754-2, IEC 60332-1/60332-1-2, UL VW-1 with tensile strength >50N, Number of Insertion upto 2500 Duty Cycle

Supply, installation, testing & commissioning of 12 Core Multi Mode OM4 Fiber (Armored) Cable from each floor to new Datacentre and terminate at both ends in the Racks as per scope of work as per given Specification etc. all complete, OTDR Scanning for OFC per core connectitvity and uplink test for Point to Point with other related testing and services (as per actual) etc all complete

Supply, Installation, testing and commissioning of 12 port LIU

Supply, Installation, testing and commissioning of Blanking plate for 24 port LIU and Modular Patch Panel (Size 6 X RJ45 Blanking plate). For 19" Panel - Black in colour).

Supply, Installation, testing and commissioning of 10 GB - 50/125μm OM3 -SC-LC Duplex Fiber Patch Cord - 2 mtrs. Conform to SC-IEC 61754-4, LC-IEC 61754-20 IEC 61300-3/4,61300-3-34,IEC 61300-3-6,61300-2-2 ANSI-TIA, IEC 60793-2-10 Type A1a.2 and Telecordia performances requirements

Supply, Installation, testing and commissioning of 10 GB - 50/125μm OM3 -LC-LC Duplex Fiber Patch Cord - 2 mtrs. Conform to LC-IEC 61754-20 IEC 61300-3/4,61300-3-34,IEC 61300-3-6,61300-2-2 ANSI-TIA, IEC 60793-2-10 Type A1a.2 and Telecordia performances requirements

Supply of Floor 42U x 600W x 650D/ 800D/ 1000D/ 1200D Stand rack with Multi hollow extrusion Aluminium profile frame, Top and bottom cover with provision of either brush cable entry or cable entry holes with rubber grommets, Front single door with Glass/ Mesh and rear double door with mesh, Static load bearing capacity of Upto 1200KG., confirming to following standards - IEC EN 60529, IEC EN 62262, ISO 9001:2008, ISO 14001: 2015, ISO 45001: 2018, Salt spray test according to ISO 9227 (NSS test) for 250 Hours, Colour - Combination of RAL 7037 (For frame) & RAL 7035 (For other parts) with fine texture Rack including accessories like Horizontal PDU, Metal Cable manager, Hardware packet and Monitor Shelf etc.

Supply, Installation, Testing & Commissioning of Core Switch with Distribution Switch with 24 x 1G SFP ports with 4 X10G SFP+ ports and 4 x 10/25G SFP28 with switching capacity of 728 Gbps, forwarding performance of 540 Mpps, dual hot swappable internal power supply, Should have Stacking with stacking bandwidth of minimum 200 Gbps. Should support min 4GB internal DRAM, 16GB internal Flash memory, 64K MAC address, 144K IPv4 Routes and 72K IPv6 Routes, MTBF: 195K Hours, Should have static routing OSPF,VXLAN,VRF, PIM and VRRP from Day 1. Should support BGPv4 and IS-IS from Day 1. The Switch should be EAL2/NDcPP , FIPS 140-2 ceritified and should be managed with both On-premise and Cloud based controller without changing it's Software image.

Supply, Installation, Testing & Commissioning of 24 Port POE+ Access Switches with switching capacity of 128 Gbps, forwarding performance 68 Mpps, having 24 x 10/100/1000BASE-T PoE-plus(RJ45) with minimum PoE budget of 380W, with 2 x 10G SFP+ uplink ports and can be upgradable to 4 x 10G SFP+ with license. Should support min 1GB internal DRAM, 1GB internal Flash memory, 16K MAC address, 4K VLAN, Latency: < 4 µs. Should have Static Routing , IGMPv3, ISSU, PVST+, LACP, Loopback detection, Built-in CPU protection against malicious attacks. It should be RoHS, WEEE certified and EN 55024: 2010,EN 55022,EN 50581,EN 61000-3-2. The Switch should be managed with both On-premise and Cloud based controller without changing it's Software image.

Supply, Installation, Testing & Commissioning of SFP Module

Supply, testing and commissioning platform type motorised ladder with following specifications:- (i) Maximum Height : Platform height upto 55 ft (platform height 10 mtr) with working height 11 mtr. This is at 80% expandable height. Tilted height: 7.5 feet (ii) Folds: Three 20+20 Aluminium Section (Temper T6) IS 733: 75 mm x 35 mm x 3 mm with corner thickness 6.8 mm supported by 5MM MS channel (Fold 1) Step distance: Step distance of 300 mm, 26 mm square tube- Non slippery grade HE 306351 T6 "Winch : 02 Nos, 6 Ton extra heavy duty (4"" drum for quick extension) with additional locking system Wheels: 2 Fix 2 Swivel, tubeless tyre (Branded- CEAT/JK/Apollo) Base on MS axel of 2x2 square rod with EN grade. Wheels fitted with honda city hose for easy movement of ladder. An additional manual break in 2 wheels to stop the ladder at required place. Trolley : 6 ft x 12 ft of 125 mm x 65 mm x 6.5 mm ISI. All other supporting angels 50 mm x 5 mm." "Platform size : 3 ft x 3 ft covered with 3 ft rallying. Side Crosses: Aluminium section 3mm + MS patti 50 x 5 mm. Rope: Double 8 mm wire ISI steel core Grade Ib 2002, Additional safety wire from top to bottom with thickness 5 mm" "Tool Tray: 12""x24"" Workmen safety belt: Full body workman safety belt will be supplied along with ladder. Nuts Bolts: Unbreako brand Parking Jack: 1.25"" thick heavy duty 4 Jacks Ladder Weight capacity: 220-250 KG at platform Ladder weight: 1100 KG" "Automation: 2 Crompton motor- One 2.0 HP and another 3.0 HP Crompton VSD drive Panel Schneider NO NC switches Inch by Inch operation for both expansion and tilting operation" "Balance Strip meter: Yes Certificate: NABL for aluminium & MS Welding"

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for 900 lpm at 35 head automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (i) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 (ii) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (iii) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (iv) Suitable cement concrete foundation duly plastered and with anti vibration pads.

Providing, installation, testing and commissioning of stainless steel Ystrainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange of 150 mm dia.

Supplying and fixing single headed Gun metal internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required

Supplying and fixing 63 mm dia, Gun metal 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Supplying & fixing 63 mm dia gun metal short branch pipe with 20mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required:

Supplying and fixing 30 m first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required:- (i) 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 (ii) 20 mm nominal internal dia gun metal globe valve & nozzle. (iii) Drum and brackets for fixing the equipments on wall. (iv) Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supplying, installation, testing and commissioning of weather proof M.S cabinet size 900 mm wide x 2100 mm height x 600mm deep fabricated from 1.6mm thick M.S. sheets and M.S angle 40mmx40mmx6mm complete with glass, locking arrangements to accommodate the following:- Gunmetal single headed Hydrant valve - 1 No. Fire Hoses 63mm, 15 M long with accessories - 2 Nos. Short branch - 1 No. First Aid hose Reel - 1 No. Fire Extinguisher - 2 Nos. Fireman's Axe - 1 No. Pressure Gauge - 1 No. The cabinet shall be painted with one coat of primer and 2 coats of synthetic enamel paint of approved shade.

Supplying, installation, testing and commissioning of fire brigade connection of cast iron body with gun metal male & female instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 2way-100 mm dia MS Pipe.

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required

Providing and fixing standard fire man's axe with heavily insulated rubber handle complete as required.

S&F MS pipe 150 mm dia conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete all as specified and directed by Engineer-in-Charge.

Providing, Installation, Testing and Commissioning of 25 mm dia Gun Metal / Bronze Ball Valves screwed ends of following sizes as required. (PN-1.6)

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

80 mm dia

150 mm dia

Providing, installation, testing and commissioning of 150 mm dia non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

Providing and fixing single acting air valve with screwed inlet 25 mm dia.

Supplying, installing, testing and commissioning approved make Microprocessor based Multi-loop, True Peer-to-Peer Networkable Addressable Fire Alarm Control Panel with minimum 600 characters LCD display, 4000 trouble events including 1000 alarm log history events,, QWERTY keypad for programming. The panel should be equipped with sufficient numbers of loops considering 20% spare capacity in each loop and shall be extendable upto 10 Loops. Each loop shall have a capacity of minimum 159 detectors & 159 other devices. The panel shall work in degrade mode in case of CPU failure, Products not having this feature may offer Redundant CPU. Four access levels, flash EPROM, 240 volts AC power supply, automatic battery charger, 24 volts sealed lead acid batteries sufficient for 24 hours normal working and 30 mins in alarm condition with the charging capacity of 200AH. The panel shall be complete with Integrated 8 channel Digital Voice Evacuation System Controller capable of broadcasting Evacuation Messages on same peer-to-peer Network and 2 ways Communication Fire Fighters System capable of supervising all the speaker circuits with adequate zone control and accessories. Failure of Fire Panel CPU shall not result in failure of DVC operation.Products not having this feature must provide dedicated CPU for DVC. The Fire Fighters Telephone System shall be capable of having minimum 30 Telephones in conference in multiple FFT Risers. The panel shall be capable of self programing without any dependancy on dongle or programming software. Quoted rate shall include supply of necessary software & hardware for progamming the panel with all necessary licence. Panel shall have Modbus/ Bacnet over IP protocol for future integration with BMS. However, for present arrangement FA system will be standalone with 24x7 monitoring. The panel shall be capable for remote accessibility on a mobile app through cloud platform/solution. Designed to meet UL864, 10th Edition 02-loop - With Digital Voice Command Center

Supplying, installing, testing and commissioning of MODbus Interface Gateway for communication with BMS / Other Utilities. MODbus shall support minimum 14000 data points. MODbus Gateway shall act as an independent node communicating on the peer to peer network and shall not be dependant on the Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of MODbus Gateway.

Supplying, installing, testing and commissioning of Addressable Multi-criteria Photo-Thermal Detector with sensitivity range of 0.5 to 4.0% obs/ft.The intelligent multi criteria detection device shall include the ability to combine the signal of the thermal sensor with the signal of the photoelectric signal in an effort to react hastily in the event of a fire situation. It shall also include the inherent ability to distinguish between a fire condition and a false alarm condition by examining the characteristics of the thermal and smoke sensing chambers and comparing them to a database of actual fire and deceptive phenomena. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user friendly rotary decimal switches. The detector sensitivity (day & night) shall be controlled from the panel to get accustomed to the local environment.The detector shall comply UL268, 7th Edition guidelines.

Supplying, installing, testing and commissioning of Addressable Photoelectric Smoke Detector with sensitivity range of 0.5 to 4.0% obs/ft. The detector shall have group decision technology for faster response & avoid false alarms. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user friendly rotary decimal switches. The detector sensitivity (day & night) shall be controlled from the panel to get accustomed to the local environment.The detector shall work on coperative mode to avoid false alarm.The detector shall comply UL268, 7th Edition guidelines.

Supplying, installing, testing and commissioning of Response indicator for all detectors located above false ceiling

Supplying, installing, testing and commissioning of Addressable Manual Call Point ( Break Glass Type). The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. UL Listed

Supplying, installing, testing and commissioning of Addressable Control Module for Sounders / Strobes / Sounder cum Strobes. The control module shall provide supervised NAC output rated at 24v DC, 2A. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Supplying, installing, testing and commissioning of Addressable Relay/Control Module for AHU, Access Control, Lifts, Staircase Pressurization, Fire Suppression & other Third Party Outputs. The relay module shall provide contact rated at 24v DC, 2A. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Supplying, installing, testing and commissioning of Addressable Monitor Module for Sprinklers, Panic Bars & other Third Party Inputs. The monitor module shall monitor potential free contacts. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Supplying, installing, testing and commissioning of Isolator Module for Isolating short / dewired / loose circuits with automatic resetting arrangement. Isolator Base can also be proposed, however in that case needs to be considered with each detector & module. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Supplying, installing, testing and commissioning of Sounder cum Strobe rated at 80 dBA @ 3m for Audible annunciation and 115cd flashintg at 1 Hz for visual indication. UL Listed

Supplying, installing, testing and commissioning of 2W Multi-Tap (0.25W; 0.5W; 1W; 2W), Wall Mount Speakers. The speakers shall be of same make as that of the Control Panel & Amplifiers. They shall be compatible with supplied Amplifiers and shall work on 70.7Vrms. UL Listed

Supplying, installing, testing and commissioning of Power Supply Unit: 24V DC.

Supplying, installing, testing and commissioning of Addressable Fire Fighter's Telephone Jack with suitable supervised module for two way communication between Remote Fire Fighter & Fire Command Center.

Supplying, installing, testing and commissioning of Fire Telephone Handset for two way communication between Remote Fire Fighter & Fire Command Center.

Supplying & laying of 2Cx1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

Supplying, installing, testing and commissioning approved make 20 mm dia. PVC flexible conduits on ceiling / wall / floor etc. complete with accessories like, Junction boxes, Collars, Bends etc.

M&L for providing and fixing in position 1.2mm thick M.S. rectangular outlet boxes for housing smoke detectors, Heat Detectors, manual Call Points, monitor module, control module on the true Ceiling / wall complete with all fixing accessories as required.

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

M&L for providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

M&L for jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

M&L for providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

M&L for providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

M&L for providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

M&L for providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Earthing with G.I. earth pipe 4.5 RM long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Office Table (3200x600x750mm) Providing & making table (3200x600x750 mm) , Structure in 19mm Ply (BWR GRADE ), Finished with 1MM thick laminate(merino), inside finished with 0.8MM thick laminate(Merino) ,including necessary hole, complete with Drawers,channels,lock & hardware etc. as per Design , drawing.(Audio Vedio room)

Auditorium chair Providing & fixing of sliding push back, auto Tipup type Auditorium chair in MS Sheet base components. Having PPCP tray for seat & Back. Seat sliding upto 150mm .The chair to have Centre to Centre distance of 490mm for chair with armrest and seat width of 450mm for chair without armrest. The row & seat number should be legible. The chair to have MS tubalur framework welded together with continuous arc welding. Tubular stand structure of 25 x 50 x 1.6mm thk. Seat frame made of MS flat of 25 x 5 mm thk. Back frame made of MS flat of 25 x 3mm thk. The chair shall have power coating of 65 microns on all the MS framework. The seat shall have polyurethane foam odf density 55+-3 kg/Cum & back to have density of 50+-3 kg/Cum. The fabric for upholstery should be polyester velvet of minimum weight 320 GSM. laminated with 3 mm thick foam for extra coushioning. The fabric should be treated for fire retardancy and scotch gaurd. The height of the back to be 950-1000mm from the ground & seat to be 400-450mm from the ground. The wooden armrest to be of 80mm & 400mm length with melamine polish in back/walnut colour. The armrest between two chairs in a raw to be shared & at the both ends to be individual, including cost of expansion fastners as required of complete in all respect to the entire satishaction of the architect or architect's representative.

Three Seater Sofa Providing & fixing/placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The structure shall be upholstered with leatherite tapestry of 1±0.2 mm thick and 571 GSM. The understructure shall consist of Stainless Steel 202 grade loop leg pipe frame having cross-section area 40mm X 20mm. There shall be PVC buffers provided at the bottom to avoid scratches on the floor. The seat size shall be 510±10 mm(D) X 1540±10 mm(W), seat height = 435±10 mm, overall width = 1860±10 mm, overall depth = 770±10 mm & overall height = 780±10 mm. Complete in all respect and to be approved by Architect and his representative.

Two Seater Sofa Providing & fixing two seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The complete structure shall be upholstered with leatherite tapestry of 1±0.2 mm thick and 571 GSM. The understructure shall consist of Stainless Steel 202 grade loop leg pipe frame having cross-section area 40mm X 20mm. There shall be PVC buffers provided at the bottom to avoid scratches on the floor. The seat size shall be 510±10 mm(D) X 1040±10 mm(W), seat height = 435±10 mm, overall width = 1360±10 mm, overall depth = 770±10 mm & overall height = 780±10 mm. Complete in all respect and to be approved by Architect and his representative.

Low back chair Providing and fixing Low back chair type of Non revolving and non-tilting chair with armrest of Fabric Upholstery material Mesh Fabrics seat material, colour black of dimension(W) 580mm x (D) 525mm x (H) 970mm (+- 10MM) with seating height 400mm, seat Depth- 400mm, seat Width- 400mm, seat base material - mild steel frame with moulded PU, density of PU <=30 and back height- 450mm, width- 400mm, armrest type - overhanging fixed type, seating capacity 1 seater finish matte.(Green Room)

Visitor/Staff Chair Providing visitor/Staff chair type of Non revolving and non-tilting chair with armrest of Fabric Upholstery material Mesh Fabrics seat material , colour black of dimension(W) 530mm x (D) 525mm x (H) 895mm (+- 10MM) with seating height 400mm, seat Depth- 450mm, seat Width- 400mm, seat base material - Hot pressed plywood with moulded PU, density of PU <=50 and back height- 450mm, width- 400mm, armrest type - moulded armrest continuousy fitted with seat and back fixed type, backrest material - injection moulded plastic, seating capacity 1 seater finish matte (AV Room)

Providing and fixing 6mm thick mirror fixed over 12mm BWP grade ply fixed to wall and surrounded with steam beech wood moulding including polishing etc. complete as per design and drawing and directions of Architect or Architect's representative..(Green Room and Toilets)

Laminated Finish Open Shelves 475mm Deep Providing and fixing low height open Shelves as per details. Top, bottom to be made out of 19-mm comm. block board (Century) with Approved pvc edge banding tape(make Rehau) match with laminate color. Back to be provided of 8-mm thick commercial ply(century).All shelves to be adjustable and made of 19 mm thick commercial board(century) .The sides of the storage to be made of 19mm thick commercial board(century). All shelves to be adjustable and made of 19 mm thick commercial board.fixed on all sides and inside surface to be finished 0.8 mm thick white laminate(Merino).Complete with all necessary fittings and size as per directions of Architect or Architect's representative.(Green Room)

Revloving High Back Chair Supplying, and placing in position of 360 degree revloving high back chair as per Image.The premium upholstery is an added touch of extra class. With its supple leather upholstery. Equipped with a multi-locking knee tilt mechanism and adjustable arms this chair is is high on back support and comfort.Size: (W)610mm X (D)500mm X (H)1300mm Leather: Semi Aniline Leather, Function: Revolving::Pneumatic Height Lift::Adjustable Armrest::Multilocking Knee Tilt, Maximum Seating Height: 24",Minimum Seat Height: 20.86", Base :Chrome Base, Locking Mechanism: Multi-Locking Knee Tilt.The pneumatic height adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs extension force. The Seat are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 30-32 kg/m3. The product should be from the manufacture under the guidance of project consultant and engineer in charge.

Revloving Medium Back Chair Supplying, and placing in position of 360 degree revloving medium back chair as per Image. The premium upholstery is an added touch of extra class. With its supple leather upholstery. Equipped with a multi-locking knee tilt mechanism and adjustable arms this chair is is high on back support and comfort.t.Dimension (W)640mm X (D)500mm X (H)1130mm, Leather: Semi Aniline Leather, Function: Revolving::Pneumatic Height Lift::Adjustable Armrest::Multilocking Knee Tilt, Maximum Seating Height: 24",Minimum Seat Height: 20.86", Base :Chrome Base, Locking Mechanism: Multi-Locking Knee Tilt.The pneumatic height adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs extension force. The Seat are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 30-32kg/m3. The product should be from the manufacture under the guidance of project consultant and engineer in charge.

Sofa Three seater Supplying, and placing in position of sofa three seater as per Image .classic Contemporary design and slender curves. The Sofa stands Firm on solid PVC legs with thick armrests that are slightly curved on the front face of the sofa. Each curve defines a seating space which provides for people to be seated comfortably. Finished in a Brown Nappa Aire Leather, the sofa makes a fantastic first impression. The Cushioning is molded such that it flows along the partition for a clean unified look. steam beech solid wood have used for framing construction of sofa. The seat cushion is made of multi layered foam of density 35-38kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. The polyster polyfill keeps the upholstery wrinke free & soft. TThe product should be from the manufacture under the guidance of project consultant and engineer in charge.

Centre Table Supplying and placing in position of centre table as per photograph. The centre table made of solid wood (steam beech) in pu matt polish.The plain glass placed the top of the table in 8mm thk. The turned wooden legs are sleek and sturdy providing the table with its support. The wood work below the glass provides the glass with a focal point and some support. Add volumes of style to yourliving room with the centre table. Material & subtype: Solid Wood -Beech Wood( spc:steam beach), Colour & Colour Family:Brown - Dark Oak,Shape:Rectangular Legs/Base:Solid Wood, Finish:Glossy,Style:Contemporary. The product should be from the manufacture under the guidance of project consultant and engineer in charge.

Side Table Supplying, and placing in position of side table as per Image.The side table made of solid wood (steam beech) in pu matt polish.The plain glass placed the top of the table in 8mm thk. The glass table top is made with strong glass and is inlaid onto the solid wood frame. The designer wooden legs are turned for a sleeker look. The framed edges slope inwards to the table top with defined edges. Material & Subtype:Solid Wood - Beech Wood ( spc:steam beach), Colour & Colour Family:Brown - Dark Oak, Legs:Solid Wood, Finish:Glossy, Style:Contemporary. The product should be from the manufacture under the guidance of project consultant and engineer in charge.

Reception Table Supplying, and placing in position of reception Table as per Image/drawing . The table top made up of 36mm thick pre-laminated particle board and understructure shall be made of 25mm thick prelaminated particle board with 2mm thk pvc edge banding . Modesty & side panel shall be 25mm thk prelam particle board with 2mm thk pvc edge banding . Table top height will be 750mm from the floor level & one additional top at the height of 300 mm above the table top rest on SS stud/prelam vertical panel . overall ht of the table 1050mm. The working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot temperature. Provision of Prelam particle board Mobile pedestal of size 400mm(L)x 450mm(D)x600mm(HT) (2 drawer + 1filling). Pedestal Top made out of 18mm thick pre laminated particle board and rest all storage to be made out of 18 mm thick prelaminated particle board . All exposed edges shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The product should be from the manufacture under the guidance of project consultant and engineer in charge.

Revolving Medium Mesh Back Chair Supplying, and placing in position of 360 degree revolving medium mesh back chair as per Image. Styled for the contemporary office space the chair boasts of a curved backrest with a central console for lower back support. this helps to improve posture and provides comfortable seating all day long. The chair is fixed to a sleek chrome vaulted base with its individual prongs powered by nylon castors. A complete executive office chair, Jordon will bring you comfort like never before. Material & Subtype:Mesh, Dimension:(W)610mm X (D)470mm X (H)1040mm, Back Type:Medium Back, Base:Chrome Base, Base Type:Revolving, Maximum Seating Height:1040mm, Minimum Seat Height:940mm, Function:Revolving::Pneumatic Height adjustment::Tilt Tension adjustment::Synchro tilt Locking:PU adjustable handle : adjustable lumbar support . The pneumatic height adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs extension force. The Seat are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3. The product should be from the manufacture under the guidance of project consultant and engineer in charge.

Conference Table- Supplying and placing in position of conference table as per photograph/drawing. The conference Table top are made out of 42mm thk plain mdf board with veneer finish pu matt polish. The table top shall be supported with side panel of 36mm thk plain mdf board with veneer finish pu matt polish and modesty panel are made out of 18mm thk plain mdf board with veneer finish pu matt polish. All exposed edges shall be provided with veneer finish and polishing. Provision of flip top boxes for wire management and raceway under the table top for wires flow. The product should be from the manufacture under the guidance of project consultant and engineer in charge.

Supply, Installation, Testing and Commissioning of WINGS at Stage with fire retardant crape black fabric ( weight not less than 290 gms/sqm of Make:Capital/ RSWM/Banswar Syntax) fixed complete on 50x 25(1.6 mm thick) MS tube framework @ 1200 (V) x600 (H) c/c backed with 6mm ply & 12mm U foam below the fabric. The rear side of the wing to have 12mm MDF. The MDF to be given 2 coats of black enamel paint after jointing fisnishing as per the manufacturers recomendations. ( Enamel paint to be paid separtley). The side edge to be given a teak wood molding of size 90x15mm duly polished in walnut shade. The wing to be mounted with central pivot mechanism for 180 degree rotational movement at top & bottom.Size 1.2 mtr (w) x 9.52 mtr (h) approx. The work shall be executed as per drawings ,specifications & instructions of Architect or Architect's representative.

Supply, Installation, Testing and Commissioning of the Border frills out of Fire retardant Crape black colour ( weight not less than 290 gms per mtr Make Comrade/ RSWM/Banswar Syntax)) fabric in 1:2 gathers & acessories like cotton dori eyelets of brass complete with 25mm dia medium grade GI pipe painted black suitably hung from the ceiling complete of size 1mtr x 11.5mtr approx . The work shall be executed as per drawings ,specifications & instructions of engineer in charge. Complete in all respect and to be approved by Architect and his representative.

imran construction company (BID ID -3341692)

Sant Construction Co. (BID ID -3355179)