REPAIR/RESURFACING TO ROADS AND PATH OF MD ACCN AND OTM ACCN AT MIL STN GANDHINAGAR

Amount

Material and labour for Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area not exceeding 400 Sqm and depth exceeding 50mm and not exceeding 100mm complete all as specified and as directed.

Material and labour for preparing black top surfaces by bruishing with wire brush for removing caked mud, existing grass on road etc sweeping with brooms and finally fanning the cleaning surfaces with air compressor to remove all loose dust and applying a priming/tack coat with bituminous primer (VG-10) applied at the rate of 5 kg per 10 sqm heated on requisite temperature by using mechanical sprayer complete all as specified and as directed.

Material and labour for laying premix bituminous macadam (consolidated thickness 75mm or less) using graded crushed stone aggregate, grading 2 with nominal aggregate size 19mm, mixed with paving bitumen of grade VG-30 mixed at the rate of 4% by weight of total mix,rolled and compacted with 8 to 12 tonne power roller to required gradient and camber complete all as specified and directed .( Note-Mix will be prepared in Mix Plant of suitable capacity)

Material and labour for preparing black top surfaces by brushing with wire brush for removing caked mud, sweeping with brooms and finally fanning the cleaning surface with gunny bags to removed loose dirt etc complete all as specified and as directed.

Material and labour for applying priming/tack coat with bituminous primer (VG-10) applied at the rate of 2.5 kg per 10 sqm heated on requisite temperature by using mechanical sprayer complete all as specified and as directed.

Material and labour for laying of bituminous premixed Semi-dense asphaltic concrete 30mm consolidated thickness with coarse aggregate of grading 1 as per MORTH specification in single layer using paving bitumen of grade VG-30 mixed at the rate of 5.50% by weight of total mix as per design mix including supply and mixing of filler (OPC Cement) laid, rolled and compacted to required gradient and camber using full width mechanical sensor paver with string sensor and compacted with 8 to 12 tonne power vibratory road roller complete all as specified and as directed.

Material and labour for hot applied thermoplasatic road marking paint inclusive type-I reflectorising glass beads as per table 800-3,800-4 of MORT&H applied in uniform thickness of at least 2.0mm and spread uniformly with reflectorising glass beads type-II @250gms per sqm with a road marking machine as per IRC-35, with traffic diversion arrangements if required complete as per MORT&H specification clause 803.4 complete all as specified and as directed

Dismentling of old unserviceable/damaged road furniture items like cat eye , solar cat eye and delinator etc of any description complete all as specified and directed.

Supply and fixing cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufactures instructions complete

Supply and fix solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufactures instructions etc. complete all as specified and directed

Supply and fixing metal tubular delinator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed

Demolition of plain cement concrete (unreinforced) as in kerb stone of any description and in any position not otherwise specifically provided including removal of debris to a distance not exceeding 500 mtr complete all as specified & directed

Material and labour for laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified & directed. Note: (i) The rates include for the use of forms, moulds or machine moulds and setting the blocks, slabs, etc. complete including raking back the joints of the internal faces (at least 10 mm) for pointing as the work proceeds or finishing with neat flush joints.

Material and labour preparation of newly plastered/concrete surface of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint(ordinary tint) over & including one coat of compatible primer complete all as specified & directed.

Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion of post in concrete, brick work, masonry etc. and making good disturbed ground complete all as specified & directed.

Material and labour stainless steel (Grade 304) framework for road sign board, made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab or as directed with suitable arrangement complete all as specified & directed.

Material and labour PCC 1:2:4, type B2, using 40mm graded mechanically crushed stone aggregate as in foundation, filling and mass concrete complete all as specified & directed.

Supply and fix in repair retro reflective sign board made of high intensity retro reflective sheeting pasted on both sides of 3mm thick Aluminum Composite Panel(ACP) sheet with letters/graphics to be overlayed high intensity retro reflective sheeting as approved by IRC/MORTH duly plotted cut of approved colour fixed with stainless steel(SS) frame work complete all as specified & directed. Make: 3M, Avery dension, Dark eye, Shakti Note: SS framework for road sign board shall be measured & paid seperately.

Demolition of cement concrete (un-renforced) in ground floor and paving not exc. 15 cm thickness (below or above ground level.) & removal of rubbish material complete all as directed by Engineer-in-charge and all as specified.

Material and labour for 75 mm thick PCC 1:4:8 type D -2 using 40 mm graded aggregate as in sub base complete all as specified & directed by Engr-in-Charge.

Providing and laying prepolished cement concrete Chequered tiles 30cmx30cmx25mm thick, with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape heavy duty , set,jointed and pointed in neat cement slurry in floors over screed bed 15mm thick 1:6 cement mortar complete all as specified & directed by Engr-in-Charge.

Material and labour for 100 mm thick PCC 1:4:8 type D -2 using 40 mm graded aggregate as in sub base complete all as specified & directed by Engr-in-Charge.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified.

DMA PROJECTS (BID ID -3344486)

ALBA AC AND REF SERVICES (BID ID -3354338)

Shree Builders (BID ID -3353570)