CA NO.CWE BLY/GE (W)/125 OF 2025- 2026SPECIAL REPAIR TO BLDG NO. P-216 (QTRS 01 TO 04) AND P-217 (QTRS 01 TO 04) OFFICERS MD ACCN AT CROSS MARG UNDER GE WEST BAREILLY

M&L for Vitrified double charged coloured ceramic tiles light shade 8-10 mm thick (rectangular) polished, area of each tiles 600 mm x 1200 mm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement and with 15mm thick screed bed 1:6 cement motar including dismantling of floor tiles and hearting complete all as specified and directed.

All as per serial item as above but as in vertical surfaces including dismantling of tiles and rendering 10 mm thick in cement mortar 1:4, as in backing layer complete all as specified.

M & L for non-skid ceremic light coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match of tiles and screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6 for laying floor finishes including dismantling of floor tiles and hearting all as specified.

All as per serial item No 3 as above but as in vertical surfaces of tiles and rendering 10 mm thick in cement mortar 1:4, as in backing layer complete all as specified.

M & L for non- skid ceremic light coloured tiles 7 to 8 mm thick (Square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match incl dismantling of tiles and screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6 for laying floor finishes all as specified.

M&L for Glazed (plain /coloured) ceramic tiles wall (450x300x7)mm / (600x300x7)mm thick on vertical faces of walls including 10mm thick rendeing in CM 1:4 set jointed in neat cement slurry and pointed in coloured cement to match including taking down old dado/skirting complete all as specified.

Taking down chowkats with shutters (without taking off shutters from the frames) area not exc 1.5 Sqm each including making good disturbed portions of wall with new or old bricks, lintel,cills, etc in CM 1:4 complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frames) area exc 1.5 Sqm each and not exc. 4.00 Sqm including making good disturbed portions of wall with new or old bricks, lintel,cills, etc in CM 1:4 complete all as specified and directed.

Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. complete as specified by the manufacturer and as per directions of Engineer-in-charge.

Supply and fixing 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table 3 of IS: 14856 complete all as specified by the manufacturer and as per directions of Engineer- in-charge.

S&F for 125x60mmx2mm thick pressed steel, frames for door with one or more rebates including filing and inner surface of the frame shall be treated with a coat of bituminous paint & compaction with PCC 1:3:6 Type C1, necessary fixing lugs, SS hinges, lock strike plate, 02 x MS bar/flat at bottom of the frame etc, complete including wooden texture finished paint on the frame surface all as specified and directed.

S&F for 105mmx60mmx2mm thick pressed steel, frames for door with one or more rebates including filing and inner surface of the frame shall be treated with a coat of bituminous paint & compaction with PCC 1:3:6 Type C1 necessary fixing lugs, SS hinges,lock strike plate, 02 x MS bar/flat at bottom of the frameetc, including wooden texture finished paint on the frame surface complete all as spd and directed.

S&F for 35 mm thick Factory made flush shutter, solid core construction with block board core and ply wood face panels, commercial type on both side, complete all as specsified & directed.

M & L for 35mm thick Factory made plain framed glazed and skeleton shutter open rebated & prepared to receive glass, gauge etc, with sash bar edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass including campsule mesh tightly fixed with the glazed and skelton door shutter etc, of 2nd class hard wood, members of shutters as specified in SSR Part - I Section 8 clause 8.24 (a) fitted to chowkats all as specified and directed. Note:- Campsule Mess will be measured and paid separately.

S&F for 20 mm thick solid PVC board, both side prelaminated, one side with decorative choice lamination, and other side plain rigid white lamination as in cup board shutters, with wardrobe/ finch lock & PVC lipping on all exposed edges of same texture and shade, with complete all as specified and directed. Note: 1) Design & layout of wardrobe and pattern / colour of lamination to be approved by GE. 2) thickness of laminated not less than 0.25mm for inside rigid white type & 0.12 (14 micron) mm for outer decorative type. The laminate shall be fixed to base with approved adhesive as per manufacturer's instructions and machine pressed to ensure proper bonding with base ply and avoid air pockets. 3) Frame to be fixed to walls, soffits & base of cupboard with fasterners.

S&F for 18 mm thick solid PVC board, both side prelaminated, one side with decorative choice lamination, and other side plain rigid white lamination as in cupboard shelves & partitions including powder coated aluminium cleat (colour of powder coated to match colour / shade of laminate) and as in fixing to sides of cupboard, soffits & base of cupboard with SS fastner also including PVC lipping on all exposed edges of same texture & shade to match the laminate complete all as specified as directed. Note: 1) Design & layout of wardrobe and pattern / colour of lamination to be approved by GE. 2) Thickness of laminated not less than 1mm for inside plain white type. The laminate shall be fixed to base with approved adhesive as per manufacturer's instructions and machine pressed to ensure proper bonding with base ply and avoid air pockets .

S&F for 16 mm thick solid PVC board, one side prelaminated and other plain white lamination, fixed on back side of wall of cup board with SS fastners complete all as specified as directed.

S&F for fancy type 200 mm long stainless steel handles etc, complete all as specified and directed

S&F for 100mm long stainless steel butt hinges complete all as specified and directed.

S&F for 150mm long aluminum anodised, barrel tower bolts of extruded section and fixed.

S&F for 150mm long aluminum handles, cast type complete all as specified and directed.

S&F for 200mm long aluminum anodised, barrel tower bolts of extruded section and fixed.

S&F for 150mm long Extruded aluminium alloy handles, fabricated type, anodised

S&F 150 mm long floor door stopper of aluminium alloy body and tongue, brass body and tongue with hard drawn steel spring fixed in floor complete all as specified and directed.

S&F 300mm long mild steel sliding door bolts plate type stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate all as spd and directed.

S&F for 1.2mm thick aluminum anodised campsule mesh aperture not more than 1 cm fixing with screw in the door for protection of mosquito wire mesh and all as spd and directed.

S&F galvanised Stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanesed wire stapels complete all as specifed and directed.

S&F 300 mm size, MS ordinary rat tail rod pattern springs including roller and roller plate complete including fixed to wooden and steel chowkats.

M&L Preparation of old wooden surfaces of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint.

M&L painting to wood and wood based surfaces of any description exc 10cm with or girth with two coats of synthetic enamel paint over a coat of pink primer including preparation of newly or previously untreated surface all as spd and directed

M & L preparation of old steel surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint

M&L for painting to steel surface exc 10 cm width or girth with two coats of synethic enamel paint over a coat of red oxide primer including preparation of newly or previously untreated surface all as spd and directed

M & L for Plain Cement Concrete 1:3:6 type C-1(using 20 mm graded aggregate) as in bed blocks for hold fast/concrete filling in chowkhats and similar work etc complete all as specified and directed.

M&L 15mm thick cement plaster on brick surfaces or concrete surfaces (on external surface) in cm (1:4) including WPC @ 200 ml per 50 kg of cement including taking down plaster finishing the surface even and smooth without using extra cement and necessary scaffolding all as spd and directed, Note :- WPC shall not be paid separately for this item.

M&L 15mm thick cement plaster on brick surfaces or concrete surfaces (on external surface) in cm (1:4) using WPC @ 200 ml 50 kg of cement newly surface even and smooth without using extra cement and necessary scaffolding all as spd and directed Note :- WPC shall not be paid separately for this item.

M&L 12mm thick cement plaster on brick surfaces or concrete surfaces (on internal surface) in cm (1:6) including taking down plaster finishing the surface even and smooth without using extra cement and necessary scaffolding all as spd and directed

M&L 12mm thick cement plaster on brick surfaces or concrete surfaces (on internal surface) in cm (1:6) newly surface even and smooth without using extra cement and necessary scaffolding all as spd and directed

M & L for rendering 5mm thick on ceiling or concrete surfaces in cement mortar (1:3) finished including taking down plaster the surface even and smooth without using extra cement and necessary scaffolding complete all as spd and directed

M & L for rendering 5mm thick on ceiling or concrete surfaces in cement mortar (1:3) newly surface even and smooth without using extra cement and necessary scaffolding all as spd and directed

M&L white washing two coats on ceiling surfaces including preparation of newly plastered untreated surfaces and necessary scaffolding all as spd and directed

M&L Preparation of old decorated surfaces and applying three coat of white wash on ceilings surfaces and rubbing down with sand paper to have even and smooth surfaces all as specified & directed by Engr-in-Charge.

M&L for preparation of old plastered surfaces of walls by complete removal of existing treatment and applying two coats of oil bound distemper using Airless spray technology operating single spray gun paint usage over a coat of 1 mm thick layer of wall care putty and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper using Airless spray technology of operating single spray gun and paint usage over a coat of 1 mm thick layer of wall care putty and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed.

M&L for preparation of old plastered surfaces of walls by complete removal of existing treatment and applying two coats of exterior weather proof paint using Airless spray technology operating single spray gun paint usage over a coat of 1 mm thick layer of wall care putty and certified by paint manufacturer and as mentioned in PS and accessories for applying weather prrof paint should be able to spray in hard to reach areas and penetration of paint on the surface to achieve excellent application using limited manpower complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of exterior weather proof paint using airless spray technology of operating single spray gun and paint usage over a coat of 1 mm thick layer of wall care putty and certified by paint manufacturer and as mentioned in PS and accessories for applying weather proof paint should be able to spray in hard to reach areas and penetration of paint on the surface to achieve excellent application using limited manpower complete all as specified and directed.

M&L brick work with fly ash bricks straight or curved on plan exc 6 m mean radius built in CM (1:6) and demolition of brick work or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins, aches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles all as spd and directed

M&L brick work with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in CM (1:4) and demolition of brick work or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins, aches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles all as spd and directed.

M & L for cutting chases of hanging chajjas, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of sunshades, shelves, lintels, Chajja ( up to IIIrd floor) etc making good, cutting out exc 10cm and not exc 40cm girth in RCC chajjas in brick walls complete all as specified and as directed.

M & L form work to edges of concrete rough finished surface flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide.

Form work to soffits of suspended slabs flat surface of concrete finished rough surfaces of concrete not exceeding 200mm thick, complete all as specified and directed.

M & L formwork to sides and soffits of lintels,lintel bend, beams etc finished rough surfaces of concrete complete all as specified.

M & L formwork to sides of pillars, posts, struts, piers, columns and stanchions square, rectangular finishes rough surfaces of concrete.etc finished rough surfaces of concrete complete all as specified.

M & L formwork to chullah hoods, chajjas, trough and similar items including edges finished rough surfaces of concrete complete all as specified.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia.

S&F TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required,including binding with mild steel wire (annealed) not less than .9mm dia.

M&L RCC 1:2:4 type B1 using 20 mm graded aggregate as in slab, shelves and stair case etc. and demolition of reinforced cement concrete, (other than ground floors), shelves, chajjas, slabs and stair case similar work carefully and matching to adjoining disturbed surfaces all as directed.all as specified and directed.

M&L RCC type B 1, 1:2:4 (20mm graded agg) as in beams, cantilevers, lintels, over 1.5 m span, columns, pillars and demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specifid and directed

M&L RCC 1:2:4 type B1 using 20 mm graded aggregate as in chajjas and like & demolition of reinforced cement concrete, (other than ground floors), shelves, chajjas, slabs and stair case similar work carefully and matching to adjoining disturbed surfaces all as directed. all as specified and directed.

Dismantling of concrete by chiseling from RCC members like column , beam, parapet facia, chajja, ceiling,etc exposing the reinforcement without disturbing the reinforcement free from rust by sand blasting/using chemical, apply a coat of rustolin to remove rust and acralic polymer on old rusted reinforcement proving at places addl reinforcement welding with existing reinforcement as directed wherever required binding RCC 50 mmx 50 mm (10 mm gauge welded mesh ) & tack , securing with clips / linding wire, welding & provision guniting pressure 2.2 to 2.5 kg /sqm with admixer 1 cement 3.5 of sand of thickness 25 to 40 mm including stripping floating with wooden strippers for proper dimension control neccssary form work & scaffolding up to three storey and including height of head room complete surface of guniting to be finished fair with 10 mm thick plaster in cement mortar 1:4 with water proofing compound @ 200 ml every 50 kg of cement and applying two coat of Dr fixit /pidilite new coat ezee at interval of 8 hours cure for the surfaces complete all as spd as directed. Water proofing Compound :-Dr Fixit (Pidiproof LW+ or pidicrete URP).

Demolition of cement concrete(un-reinforced), in any position and paving n.exc. 15 cm thickness (below or above ground level) including tile/ terrazzo floor complete all as specified and directed.

M & L for plain cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in plinth protection 75 mm thick finished even and fair including forming 10 mm wide joints at not exceeding 3 m distance between adjoining slabs shall not exceed 10 mm in thickness and shall be filled with bitumen mastic i.e. bitumen and sand in proportion 1:2 all as specified or as directed.

Providing water proofing treatment to RCC sunken slab as specified and directed as under:- (a) Cleaning the existing RCC sunken slab and vertical wall/RCC beam and hacking the surface. (b) 15mm thick plastering over the floor & vertical surface in CM 1:4, mixed with liquid water proofing compound @ 200ml per 50 kg of cement trowelled to even and smooth finish without using extra cement .(Water proofing compound shall be measured and paid separately). (c ) filling the sunken portion with water for 72 hrs and carring out the ponding test.(Any leakage /seapage noticed shall be repaired). (d) Applying two coats of elastomaric acrylic water proof coating Make: Dr. Fixit of pidiproof LW+ or equivalent per sqm in each coat with roller application.(Note: Each coat of elastomaric acrylic compound requires 6-8hrs to dry up itself second coat shall be applied on getting the first coat completely dried up.)

Supply only liquid waterproofing compound all as specified. Make : Dr. Fixit (pidiproof LW+)

M&L for cement concrete type E2 1:5:10 (40 mm graded aggregate) as in mass concrete

S&F 32mm dia GI pipe, medium grade as in spout pipe in sunken floor complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of concrete surfaces in CM 1:4 with water proofing compound concrete surface complete all as specified and directed.(NOTE:- WPC shall be measured and paid separatly)

Dismantling of roof terracing cement / brick concrete (un-reinforced) and existing water proofing treatment of any thickness in any position and of any portion from top of roof of building, cleaning surface of roof with wire brush / mechanical brush and with water thoroughly to remove all dust / dirt and loose particles to expose base concrete roof slab and removal of rubbish / demolished material out of MD land complete all as specified.

M&L 25mm thick cement concrete type B1 1:2:4 using 20mm graded stone aggregate in floor finishes even and fair to receive floor tiles.

Supply and providing water proofing treatment with polyster based water waterproofing membrane standard water proofing membrane 3 mm thick, wt not less than 3.5 kg/ sqm having 10 years guarantee for water tightness all as specified and directed and described as under :

(a) Prepartion of RCC roof surface and applying one coat of polymer modified bitumen 85/25 @ 1.2 Kg/Sqm over a coat of polymer primer @ 0.30 Kg/Sqm including cleaning surface, all as per manufacture's specification complete all as specified and directed.

(b) Supply & Providing APP based polyster based water waterproofing membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced/ torch application of membrane with 10 cm overlaps as required thereof, complete all as specified or as directed. Make :- IWL Hyperplas Polyster (M/S IWL), Super Thermolay (M/S STP Limited), Torch Shield AP by Pidilite Industries.

M & L for heat reflective weathering tile minimum 250 x 250 x 15 mm thick, fixed with neat cement slurry over laid over 15mm thick screed bed in cement mortar 1:4 on roof top and joints shall be 4mm wide, sealed with 2 mm deep polysulphide compound (sealing compound) complete all as specified and directed.

M&L for 20mm thick Granite (Z- black colour only) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. stone including grinding and polishing and 15mm screed bed in cement mortar 1:6 including dismantling of tiles, hearting etc complete all as specified.

M&L for 20mm thick Granite (Z- black colour only) machine cut and machine, polished,and moulding, window cills, riser of steps and urinal partition wash basin platforms and flooring, skirting/ dados like in cement mortar(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of marble laid over cement screed and jointed with grey cement slurry mixed with pigment to match including rubbing & mirror polishing ding and inclucding 10mm thick cement plaster on brick surfaces or concrete surface in cm (1:4) finished even and rough as screed and dismantling of wall tile including cement mortar bedding complete all as spd and directed.

M & L for 18-20 mm thick machine cut pre polished kota stone slab flooring laid under stairs soffits area and jointed with grey cement slurry fixed with pigment to match to shade of the slab including rubbing and mirror polishing over and or 20 mm thick bedding layer of cement mortar 1:6 for laying floor finishes even and rough with and including dismantling floor, hearth or wall kota stone slab including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for 20-25mm thick machine cut pre polished kota stone slab in riser of steps skirting, dado and pillar,landing in single piece with round nosing with three numbers of serration using as front door steps, laid over cement screed and jointed with grey cement slurry mixed with pigment to match including rubbing & mirror polishing ding and inclucding 10mm thick cement plaster on brick surfaces or concrete surface in cm (1:4) finished even and rough as screed dismantling of wall tile including cement mortar bedding complete all as spd and directed.

S&F 15 mm thick (minimum) Johnson Endura stepping tiles of anti skid surface as in riser & treads in steps, and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of stone including making 03 x self embossed tread lines in length wise 25mm centre to centre with bull nosed complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps , cooking platform, and other similar situations complete all as specified and directed

S&F in repairs Vitreous china wash down water closet single piece (Cascade pattern) with seamless flushing cistern square design duroplast slim seat cover, slow falling seat cover size 69x37x77CM / 66x35x71 complete, including connection to drain pipe etc complete all as specified and directed.

S&F in repair vitreous china squatting pan of orrissa pattern long pan size 580 x 440 mm white with "P"or "S" trap size 100 mm dia front or back inlet and integral foot rest any pattern (excluding flushing cistern and flush pipe) including provn of lime concrete bedding (1:2:5), minimum 150mm all round and finish just below level of rim of pan complete all as specified and directed.

S&F in repair PVC low level flushing cistern 10 litres, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, flushing pipe complete all as specified and directed.

S&F in repair fancy type chromium plated brass angle valve type suitable for 15mm bore pipe complete all as specified and directed.

S&F in repair 15 mm dia bib tap fancy type chromium plated with flange quarter turn incl all necessary fittings complete all as specified and directed.

S&F in repairs 450mm long PVC connection 15mm bore with PTMT nuts.

Taking up or down 15 mm dia steel tubing and connections including cleaning for refixing or removal to store complete all as specified or as directed.

Taking up or down 20 mm dia steel tubing and connections including cleaning for refixing or removal to store complete all as specified or as directed.

S&F for 15mm bore galvanised steel water tubing with all fittings 'medium grade' and fixed complete to wall and ceiling or laid in floors complete all as specified or as directed.

S&F for 20mm bore galvanised steel water tubing with all fittings 'medium grade' and fixed complete to wall and ceiling or laid in floors complete all as specified or as directed.

S&F stainless steel kitchen sink with double bowl without drain board made of 1 mm thick 304 grade stainless steel with plugs washers and waste pipe and coupling, round stainer including bedding in cement mortar on dwarf walls including brackets and connecting union to pipe complete.

S&F in repairs 100mmx100mm stainless steel grating fixed

S&F in repair fancy type stainless steel towel rack size 600mm long including a pair of brass bracket complete all as specified and directed.

S & F stainless steel plate rack not less than 5 Kg of weight & size 31"X36"X10" complete all as specified and as dirrected. Make : Siver shine SSK-135, BSKPR-315 Bluestar

S&F in repairs Vitreous China table/counter top wash basin of suitable size (480 x 370 x 130 mm minimum) including SS bottle trap, and cabinet of PVC shutter fixing on counter with SS waste coupling complete all as specified and as directed.

S&F in repair fancy type brass chromium plated toilet paper holder, complete all as specified and as directed.

S & F in repair fancy type 150mm size square brass CP shower rose with or without swivel joints complete all as specified and as directed.

S&F in repairs brass chromium plated wall mixer 3 in 1, 15mm for mixing hot & cold water screwd down three joints to steel pipes or unions and plugging and screwed to walls incl necessary fitting complete all as specified and as directed.

S&F in repair fancy type 15mm dia chromium plated fancy type wall mixer hot & cold with long swan for kitchen sink fixing and connection to pipes incl necessary fitting complete all as specified and as directed.

S&F in repairs health faucet 1 mtr SS Braided connection tube with wall hook complete for ETWC incl necessary fitting complete all as specified and directed.

S & F magnet catch with striking plate including letting in complete all specified and as directed.

S&F stainless steel of AE- SI 316 grade tubular towel ring including a pair of CP brass bracket complete & necessary fitting all as specified and directed.

S&F in repair fancy type brass chromium plated soap dish of 160x160x90 mm complete all as specified and directed.

S & F in repair fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP bracket gaurd and railling 60 cm long complete all as specified and directed.

S & F Brass CP Hand Shower with 15mm dia 1.2 Meter long flexible tube and wall hook screwecd for iron pipe fancy type long body complete all as specified and directed.

S&F in repair fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with fancy type screws complete all as specified and directed.

S&F in repairs of PVC corner set of three of size (12'X12" ,9"X9" and 6" X6" ) with railling and complete all as specified and directed.

S&F in repair fancy type 15 mm bore brass chromium plated WHB mixer for mixing hot and cold water screwed down for iron pipe and fixed to WHB including taking out existing mixer from old WHB complete all as specified and directed.

S/F low density polyethene pipes (LDPE) 32mm of pressure rating 6 Kg/cm2 fixed to walls.

S&F in repairs stainles steel Curtain Rod 25 mm dia of approved quality with two number decorative design as approved brackets fixed in brick/concrete wall and same finished knobs on each end of curtain rod all as directed and specified.

S & F 500 ltrs capacity rotational moulded polythylene triple layered water storage tanks white in colour (cylindrical vertical with closed top) hoisted and fixed in position and dismantling water tanks / demolition of RCC tanks of any size / capacity and making good the distrubed portion complete all as specified and directed.

S&F 1000 ltr capacity Rotational moulded polyethylene triple layered water storage tanks white in colour (cylinderical vertical with closed top) hoisted and fixed in position and dismantling water tanks / demolition of RCC tanks of any size / capacity and making good the distrubed portion complete all as specified and directed.

S&F 20 mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms complete all as specified or as directed.

S&F in repairs of 32 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F Mild steel OHT cage, bands, straps, supports or stay, for rain water, ventilating pipes including bolts if reqd, hooks (stay) heavy for large gates hook and pintle large hasps and staple, chains hand made sliding bolts clamps, hold fasts wall ties etc etc hooks for hanging fans plain angle cleats for securing purlins to wood truss or rafter, knee piece inserts, two way and three way straps, plate washer and similar small articles confirming to Fe-290 Gde - E-165 all as spd and directed.

Taking up or down AC/PVC rain water pipe, soil/waste/vent pipe of any size with fittings etc.

S & F PVC (SWR) 110 mm dia soil waste or rainwater drainage pipes single socketed in any length with rubber ring joint laid in floor or fixed on wall all as specified or as directed.

S & F PVC (SWR) 110 mm bore bends all as specified or as directed.

S&F in repair PVC (SWR) multi floor trap with grating including jointing with solvent cement floor trap 75 mm dia outlet plain including jointing to waste pipe fixed in cement concrete (1:2:4), type B-1 complete all as specified and as directed.

S&F in repair PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fitting complete all as specified and as directed.

S & F spun iron soil, waste and vent pipe, 75mm bore, in any length with or without ear with cement joint fixed to walls complete all as specified

S&F 100mm bore PVC bends (any radius) diminishing pieces or tapers (larger bore mesured) with oval access door

S&F 80mm bore PVC bends (any radius) diminishing pieces or tapers (larger bore mesured) with oval access door

S&F in repairs 80 mm bore PVC cowl complete all as specified.

S&F powder coated aluminium frame for windows, ventilators and kitchen cupboards frame size 100x44mm and 2mm thick with one or more rebates including joining cleat for fixing etc and add for powder coating (minimum thickness of powder coating 50 micron) complete all as specified.

S&F for powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) each shutter complete all as specified and directed. Note : Cost of rubber beading and required accessories shall be included in the rate of item and will not be paid extra.

S&F powder coated aluminium sliding windows frame with movable shutter (sliding on minimum two PVC roller of best quality) for each shutter on three tracks with stainless steel mosquito proofing and glazing shutter and including 5.50 mm thick figured glass & stainless steel wire mesh fixed with neoprene rubber gasket with aluminium beading, clipsa, frame made with aluminium section as appended below- (i) Window frame :68.4x38mm X 1.15 mm thick for three tracks. (ii) Top/bottom rail and style / rail of shutter : 15x37.5x1.15 mm thick and over. (iii) Aluminium beading - 0.7mm thick (iv) stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed in aluminium window or along with F/Y section fixed with aluminium wire staples complete. (v) Aluminium fittings such as aluminium suitable handle with auto interlock cap with suitable size . (vi) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed.

S & F for stainless steel glossy finish hat peg set of five tier with necessary fitting complete all as specified and directed.

M&L for 100x100mm Stainless steel floor trap Anti cock roach proof Trap

M&L for stainless steel (AISI 304 Grade ) Non magnetic multilayer nikle chrome plated for multipurpose utensil container including frame work telecscopic channels, handles etc as reqd and complete all as specified and as dircted utensil sample, design and pattern of each basket to be approved by GE the foloowing size in each kitchen. (a) plain basket 510x470x100mm or 520x485x100mm or 530x505x150mm slace godrej code 6126 Baan code LKY2PB 2014 -Evershine size 520x485x90mm of 03 nos (b) multisize plate basket of size 510x470x150mm or 520x485x150mm or 436x500x200mm (Clear depth 500mm) 02 nos make Silk Elnora BAAN code LKY-3CS214- Ever shine size 520x485x90mm approved by GE (c) Cutlery Basket, with Perforated bottom and side of compacted -slots for holding cutlery of size 510x470x100mm or 520x485x100mm or 144x468x50 (Clear dpth of 500mm) 02 nos make Silk Elenora (Asian Paint) code 600, size 530x505x100mm (Godrej Product code 6134 BAAN Code LKY2PC214/Ever shine size 520x485x95mm (d) Plain basket of size 510x470x200mm or 520x485x200mm or 486x500x200mm 02 Nos make Silk Elenora (Asian Paint) code 600, size 53x505x200mm- Godrej product code 6128 BAAN code LKY 2PB218- Evershine size 520x485x180mm (e) pull out with 2 basket each of size 150x485x80mm or 100x485x80mm 01 Nos make Sleek Elenora (Asian Paint ) code 250 size 180x500x590mm / Godrej product code 6141 baan code LKYNS2SP6/Ever shine size 610x485x90mm (f) dust bin as reqd 01 Nos Make 200 series of Hettich

S&F for mild steel window grills box type framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding, FE-290 grade E-165 complete all as specfied and directed.

S&F for Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays for 75mm dia pipe, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S&F for Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays for 100mm dia pipe, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S&F for 3.15mm dia magic eyes for looking out side from main of door and for safety pupose only complete all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4 type B2 (using 20mm graded aggregate) for levelling of sub base of flooring complete all as specified and directed.

S&F for computerised reflective letter / bldg number on ACP sheet (size 45 cm x 45 cm) and fixing with 04 nos of screw, rawal plug etc on wall in front of building complete all as specified and directed.

M&L for surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out

Dismatling of bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc. (each layer)

Excavating in trenchs, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in sof/loose soil complete all as specified.

M&L for 75mm thick PCC 1:4:8 type D-2 using 40mm graded stone agg in sub base flooring complete all as specified & directed.

M&L for PCC kerb stone outer coloured surface machine pressed factory made of size 300 mm long , 300mm wide, 150mm thick and 350 mm in deep using as in pcc (1:2:4) type B1 (using 20 mm graded stone agg) incl form work weathering, slightly rounded or chamfered angles and throating all as specifed and directed

M&L for Machine pressed precast conctete interlocking paver block with gray cement and pigment any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade over 25mm thick sand cushioning including watering and consolidation complete all specified and directed.

Returning, filling, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified.

Removing excavated Soil material n exc. 50m and depositing wheredirected at a level n exc. 1.5 m above the starting point

Taking down carefully aluminium point wiring any type including battens if any except for ceiling or where not feasible for light/ fan//bell/socket or power and including unscrewing from board, fitting and fixture such as switches,socket, ceiling rose,lamp holder,pendants, bracket and regulator etc and removing material from site including making good disturbed surface to match with the existing surface complete all as specified.

Taking down carefully UNSV main switch DBs of any description of an size in any position complete all as specified.

Taking down submain wiring including all accessories complete all as specified and directed.

Material and labour for point wiring with single core FRLS 1100 volt grade cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI marked not less than 20mm dia, with all conduit accessories, screws (concealed conduit wiring in walls and casing capping on ceiling or roof) including metal box suitable for modular fittings and covered with modular plate and cover of suitable size with new brass screws for mounting switch sockets and regulators and drawing continuous earth wire with and including PVC sheathed 1100 Volts grade cable with stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to main earth dolly complete all as specified for:-

(a) One light / fan/ exhaust fan point controlled by one switch.

(b) One 5 pin 5 Amp switch socket out let point on an independent board.

(c) One 5 pin 5 Amp socket out let point controlled by one switch on same board.

(d) One buzzer/ bell point controlled by one push button on the same board with other switches or independent

(e) One light point controlled by two 2 - way switches , on indepndent board.

All as per item 6 here in before but for one 15 Amp 6 Pin switch socket out let independent with 2.5 Sqmm FRLS (Nominal Area) PVC unsheathed copper conductor single core multistranded incl 2.5 sq mm FRLS PVC copper conductor single core used as earth continuity conductoe complete all as specified.complete all as specified.

S & F Modular switch one way 6 A, 1 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular switch one way 16 A, 1 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular switch Two way 10 A, 1 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular bell push 6 Amp, 1 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular Socket 6 Amp, 2/3 Pin combined 2 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular Socket 6/16 Amp, 2/3 Pin combined 2 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular fan regulator Step up type, 120 Watt, 2 Module complete all as specified and directed by the Engr-in-Charge.

Supply and Fixing ceiling rose PVC / Poly carbonate, Isolated body, three terminal AC 230 volts complete all as specified and directed.

M & L for replacement of lamp holder, PVC / Poly carbonate, insulated body modular type with back plate batten/angle type for batten fittings complete all as specified and & directed

S&F in replacement LED mirror light fitting of 1 x 10 watt LED batten with aluminium housing with all accessories prewired suitable for wall /surface mounting complete with connection all as specified and directed.

S&F in replacement LED mirror light fitting of 1 x 20 watt LED batten with aluminium housing with all accessories prewired suitable for wall /surface mounting complete with connection all as specified and directed.

Supply and fixing surface mounting LED slim square down lighter made of PDC Al with high efficint LEDs and glare free opal diffuser, IP 20 12 watt 220 volts AC complete with drivers, holders,LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete

S&F indoor decorative LED City-3 light fitting suitable for & including single 12 Watt LED lamp with polycarbonate body with upper globe complete all as specified and directed.

Supply and Fix LED lamp 12 Watt, 230 V , AC integrated circuit complete all as specified and directed.

Supply and fixing Buzzer, Ding Dong AC. 230 volts,single pole

Supply & Fixing security light fitting, LED type, 25 Watt, 6000 K, pressure die cast housing with prismatic polycarbonate diffuser & indvl LEDs as light source with integrated electronic driver complete with M&L GI pipe mounting bracket of size 25/32 mm dia and 1.20 m long fixed to wall with and including nut, bolts and GI clamps of size 50 x 6 mm as required including two coats of synthetic enameled paint over a coat of primer and making connection with three core 23/.0076 rubber insulated copper cable from ceiling rose to connector of street light complete all as specified and directed.

S & F of 1100 volts grade heavy duty two single core 4 Sqmm size (Nominal Area) PVC insulated (FRLS) copper multi-stranded conductor cable as in sub main wiring, drawn into & including PVC conduit medium grade not less than 25 mm dia including its all accessories & fittings, fixed concealed with and including chase cutting and making good the same as per existing specifications along with a continuous run of 4 Sqmm size (Nominal size) stranded copper conductor PVC insulated (FRLS) (green colour) cable as earth wire complete all as specified and directed. NOTE: - TWO SINGLE CORE CABLES ALONG WITH EARTH WIRE AND PVC CONDUIT SHALL BE MEASURED AS ONE UNIT LENGTH.

M&L for sub main wiring with 4 single core 6 Sqmm (FRLS) copper conductor PVC unsheathed cable medium grade including PVC conduit (appropriate size) concealed in wall for sub main connection including 6 Sqmm (FRLS) PVC insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly all as specified. ( Note :-twor runs of 6 sqmm (FRLS) and one run of 6 sqmm (FRLS) copper conductor shall be measured as one unit length.)

Taking down carefully ceiling fan from existing site and carry out servicing by opening the motor , removing/ cleaning the dust from complete body , oiling greasing complete incl one coat of white enamel paint in complete fan and lovers.wall or as reqd at site all as directed by Engineer-in-Charge.

Taking down carefully exhaust fan with lovers from existing site and carry out servicing by opening the motor , removing/ cleaning the dust from complete body , oiling greasing complete incl one coat of smoke grey enamel paint in complete fan and lovers .Cutting of wall in appropriate size for fixing of exhaust fan and making good the surfaces of wall and make the fixing arrangement with grouting four Nos fully threaded bolts on wall or as reqd at site all as directed by Engineer-in-Charge.

Taking down carefully Geyser from existing site and carry out servicing by opening , removing/ cleaning the dust from complete body , complete incl one coat of smoke grey enamel paint complete geyser and making good the surfaces of wall and make the fixing arrangement with grouting four Nos fully threaded bolts on wall or as reqd at site all as directed by Engineer-in-Charge.

S&F MCB single pole 6 to 32 Amp 240 Volt 'B' curve 10 KA complete all as specified and directed by the Engr-in-Charge.

S&F MCCB Triple pole and neutral 100 Amps 415 Volt curve 10 KA complete all as specified and directed by the Engr-in-Charge.

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps

Taking down carefully electric/electronic meter and deposited in MES Yard all as directed by Engineer-in-Charge.

Supply and fix TPN DB -TPN DB 8 way suitable for MCB 63 Amps , 415 Volt, 3 Phase, 4 wire AC 50 Hz having aluminium Bas Bar phase and the neutral insulated with PVC sleeves, connected with appropriate size copper thimbles.

Supply and fixing 415V 10KA 'B' curve miniature circuit breaker (MCB) of TPN/FP 40 to 100 AMP current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed by the Engr-in-Charge.

Supply and fix TPN DB -VTPN DB 4 way with provn of MCCB 160 Amps , 415 Volt, 3 Phase, 4 wire AC 50 Hz having aluminium Bas Bar phase and the neutral insulated with PVC sleeves, connected with appropriate size copper thimbles.

Material & Labour for earthing complete including taking out old unsv and replace with galvanised steel earth plate 600x600x 6mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 meters below normal ground level, surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate using 4 mm dia GI wire as earth wire electrode moulded and rivetted to earth plate at one end and connected to main switch/ control switches of buildings at another end, GI earth wire encased in and including 15 mm dia GI 'light grade' pipe from upper end of earth plate upto main switch board of building including 20 dia bore GI pipe 'light grade' as water pipe from earth chamber and including excavation and earth work, PCC 1:3:6 type C1 chamber and MS angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B1 using 20mm graded stone aggregate reinforced all as specified

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size

Taking down carefully service connections of any description from pole, wall or service brackets etc including making good disturbed surface to match with the existing surface complete all as specified.

Supply and laying & testing UG cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (Heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm, 3.5 core.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth and getting out in hard/dence soil for laying of LT UG cables/base for Pole etc complete.

Returning, filling in, including spreading levelling, watering and well ramming in layers not exceeding 25 cm thick in hard/dense soil

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point.

M&L for sand cushioning laid in trenches for laying of LT UG cables complete

M&L Modular bricks common burnt clay building bricks, sub-class ‘B’ designation-75 for LT UG cable protection complete all as spd and directed.

S&F GI tubes light grade of dia 80 mm with all fitting and fixed complete for protection of LT UG Cables laid to walls or in floors or along with poles etc complete all asspd and directed.

Please Enable Macros to View BoQ information