Balance work for construction of PHC Balichowki SH C/o Toilet block and septic tank

Amount

Excavation in foundation, trenches etc. in earth work in all kinds of soil such as pick work, Jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/dewatering upto any lift, stacking the excavated soil upto any lead from the edge of excavation and then returning the stacked soil in layer when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Excavation in drain and channels etc. in earth work in all kinds of soils such as pick work, jumper work, pick jumper work , pick jumper blasting work , blasting work in soil and hard rock conglomerate rock or saturated soil and its intermediate classification of soil including chiseling/wedging out of rocks (where blasting is prohibited) and pumping or bailing watering/dewatering including dressing of sides and bed and disposing of excavated earth upto any leads and lifts disposted earth to be leveled and neatly dressed including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing form work with steel plates 3.15mm(Three point fifteen millimeter) thick welded with angle iron in frame 30x30x5mm(Thirty millimeter into thirty millimeter into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and bellies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in situ-reinforced concrete and pain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge . Flat surfaces such as soffits of suspended floors, roofs, landings and the like Floors etc upto any thickness.

Beams, cantilever, girders and lintels sides and soffits of beams, beam hunching, cantilevers, bressumers and lintels in any depth in all height from floor.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like.

Edges of slabs and breaks in floors and walls in any width.

Providing and laying cement concrete 1:4:8 (1 cement:4 sand:8 graded stone aggregate 40mm (fourty millimetre) nominal size) and curing complete excluding cost of form work in Foundation and plinth including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Providing and laying cement concrete 1:3:6 (1 cement:3 sand:6 graded stone aggregate 40mm (fourty millimetre) nominal size) excluding cost of centring and shuttering in Foundations and plinth including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Providing and laying cement concrete 1:6:12 (1 cement:6 sand : 12 graded stone aggregate 40 mm (fourty millimetre) nominal size and curing complete excluding cost of centring and shuttering in foundation and plinth including carriage of material up to all leads and lifts and as per direction of Engineer in charge.

Providing and laying damp proof course 50 mm (fifty millimetre) thick with cement concrete 1:2:4 (1 cement:2 sand:4 graded stone aggregate 20mm (twenty millimetre) nominal size and curing complete including carriage of material up to all leads and lifts and as per direction of Engineer in charge.

Providing and laying cement concrete 1:2:4 (1 cement:2 Sand:4 graded stone aggregate 20mm (twenty millimetre) nominal size and curing complete excluding cost of form work in Foundation and plinth including carriage of material up to all leads and lifts and as per direction of Engineer in charge.

Providing and laying mechanically mixed and vibrated cement concrete 1:1.5:3 (1 cement: 1.5 sand : 3 graded stone aggregate 20 mm (Twenty millimetre) nominal size ) and curing complete excluding cost of form work and reinforcement for reinforced concrete in, Suspended floor roofs ,landing carriage and shelves and their supports balconies beams , girders , bressumers and cantilevers upto floor all level including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and laying cement concrete work 1:2:4 (1 Cement:2 Sand:4 graded stone aggregate 20 mm nominal size) mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced concrete work in Suspended Floor roofs, landing and shelves and their support balconies,beams, girders, bressumers and cantilever upto floor all level including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire up to any level including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Stone filling dry hand packed in under floor as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

filling in plinth with sand under floors including watering ,ramming, consolidating and dressing complete. including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (1 cement :6 sand : 12 graded stone aggregate 20mm (twenty millimetre) nominal size) at plinth level in Cement Mortar 1:6(1 cement:6 sand) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including raking out joints in Cement mortar 1:3 (1 cement : 3 sand) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including raking out joints in Cement mortar 1:5 (1 cement : 5sand) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Extra for Squared rubble masonry coursed with hard stone of approved quality in including raking out joints in Cement mortar 1:5 (1 cement : 5sand) Superstructure above plinth level and upto floor any level including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Extra for squared rubble masonry coursed with hard stone of approved quality in Square and Rectangular pillars Cement mortar 1:5 (1 cement : 5sand) upto floor any level including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Precast concrete block masonry (including quion blocks,jamb blocks, closer etc.) with solid concrete blocks of approved size made of cement concrete 1:3:6 (1 cement:3 sand:6 graded stone aggregate 40mm (fourty millimetre) and down gauge foundation and plinth upto any level in Cement Mortar 1:6 (1 cement : 6 sand) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Precast concrete block masonry in partition walls 10 cm (ten centimetre) thick with solid block of approved size including quion blocks, jamb blocks, closer etc. made of cement concrete 1:3:6 (1 cement:3 sand:6 graded stone aggregate 40mm (fourty millimetre) and down gauge in Cement Mortar 1:6 (1 cement : 6 sand) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Providing and fixing 10mm (ten millimetre) thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 600x600mmx10mm (six hundred into six hundred into ten millimetre) manufactured of approved shade and colour in flooring, treads of steps and landings mlaid over 12mm (twelve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete upto floor any level including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Providing and laying Duro stone vetrified tiles 300x300mmx8mm (three hundred into three hundred millimetre into eight millimetre) in grey/coloured of required shade in skirting risers of steps and dados on 12mm (twelve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete upto floor any level including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Providing and fixing factory made PVC door frame single rebate of any clours of size 50x47mm (fifty into fourty seven millimetre) with a wall thickness of 5mm made out of extruded 5mm (five millimetre) rigid PVC foam sheet heat bend & mitred at corners and jointed with 2 Nos. of 150mm (one hundred fifty millimetre) long brackets of 15mmx15mm (fifteen millimetre into fifteen millimetre) M.S. square tube, the vertical door profiles to be reinforced with 19mmx19mm (nineteen millimertre into nineteen millimetre) M.S. square tube of 19 gauge EPDM rubber gasket weather seal to be provided throughout the frame i/c fixing of door frame to wall with M.S. screws 100long with wooden or rawl plugs emedded in masonry complete including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Providing and fixing to existing door frames, 30mm (thirty millimetre) thick factory made PVC panelled door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x19mm (nineteen millimetre into nineteen millimetre) for styles and 15mmx15mm (fifteen millimetre into fifteen millimetre) for top & bottom rails, M.S. frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm (five millimetre) thick heat moulded PVC "C" channel of size 30mm (thirty millimetre) thickness, 70mm (seventy millimetre) width out of which 50mm (fifty millimetre) shall be flat and 20mm (twenty millimetre) shall be tappred in 45 degree angle on either side forming style and 5mm (five millimetre) thick, 95mm (ninety five millimetre) wide, PVC sheet out of which 75mm shall be flat and 20mm (twenty millimetre) shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm (one hundred fifteen millimetre) wide PVC sheet out of which 75mm (seventy five millimetre) shall be flat and 20mm (twenty millimetre) shall be tapered on both side to form lock rail, top, bottom and lock rail shall be provided either side of the panel 10mm (ten millimetre) thick, 20mm (twenty millimetre) wide cross PVC sheet be provided as gap insert for top rail and bottom rail paneling of 5mm (five millimetre) thick both side PVC Sheet to be fitted in the M.S. frame welded/sealed to the style & rails, joints mitred and jointed with solvent cement adhesive including fixing of PVC shutter with existing frame with M.S. butt hinges 100x50x1.90mm(One hundred into fifty into one point ninety Millimetre) size with necessary screws etc complete including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Providing and fixing to existing door frames 30mm (thirty millimetre) thick factory made wire mesh solid PVC door shutters consisting of frame made out of M.S. tube of 19 gauge thickness of size 19mmx19mm (nineteen millimetre into nineteen millimetre) for style and 15mmx15mm (fifteen millimetre into fifteen millimetre) M.S. square tube for top, bottom & Lock rail M.S. frame shall have & coat of steel primer and covered with 5mm (five millimetre) thick PVC solid sheet heat moulded "C" channel of size 75mmx30mmx60mm (seventy five millimetre into thirty millimetre into sixty millimetre) out of which 10mm (ten millimetre) shall be bent at 90degree towards inner side on front face of the door M.S. frame at lock rail shall be covered with 100mm (hundred millimetre) wide PVC sheet out of which 10mm (ten millimetre) on both the edges shall be bent at 90 degree on front face of the door and 85mm (eighty five millimetre) wide PVC sheet shall cover the M.S. frame at top, bottom & lock rail lof 70mm (seventy five millimetre) on back side of door 5mm (five millimetre) thick 20mm (twenty millimetre) wide cross PVC sheet as gap insert for top and bottom rail, PVC sheet beading of 10mm (ten millimetre) thick, 15mm (fifteen millimetre) wide PVC sheet beading in to be stick internally in the back side of style and rails of door with solvent cement adhesive including fixing of G.I. wire mesh 85G or 0.56 dia wire fixed between PVC sheet of style and rail bent at 90 degree on front face using 15mmx15mm (Fifteen millimetre into fifteen millimetre) L-shape PVC beading nailed on style a rails including fixing shutter to existing door frame with M.S. butt hinges 100x58x1.90mm (hundred into fifty eight into one point ninety millimetre) with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Providing and fixing 300x16mm (Three hundred into Sixteen millimetre) aluminium sliding door bolt and nuts screws etc. complete. as including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing aluminium sliding door bolt and nuts screws etc. including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge . 200x10mm(Two hundred milimetre into ten milimeter )

150x10mm(One hundred Fifty milimetre into ten milimeter )

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge. 125mm (One hundred twenty five milimetre)

100mm (One hundred milimetre)

Providing and fixing 150 mm (one hundred fifty millimetre) bright finished hard drawn hooks and eyes. including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and laying spartic ceremic tiles 5.5mm (five point five millimetre) thick in flooring 300 x300mm (three hundred into three hundred millimetre) Size treads of steps laid on a bed of 12mm (twelve millimetre) thick cement mortar 1:3(1cement: 3 sand) finished with flush pointing in white cement including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Providing and laying spartic ceremic tiles 5.5mm (five point five millimetre) thick in flooring 300 x300mm (three hundred into three hundred millimetre) Size riser of steps laid on a bed of 12mm (twelve millimetre) thick cement mortar 1:3(1cement: 3 sand) finished with flush pointing in white cement including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Providing and fixing 15 cm (fifteen centimetre) wide 45 cm (fourty five centimetre) overall semicircular 0.80mm (zero point eighty millimetre) thick sheet plain G.I. sheetgutter with iron brackets 40x3mm (fourty into three millimetre) size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Providing and fixing 100mm (hundred millimetre) dia pipes on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm (four point five kilogram per square metre) including filling the joints with approved adhesive complete including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge. Plain bend 100 mm (hundred millimetre) dia

PVC corner type bend 100 mm (hundred millimetre) dia

PVC shoe 100 mm (hundred millimetre) dia

Providing and fixing 0.60mm (Zero point six zero milimetre) thick preprinterd steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) micons primer coating to back coast of polyester of 5 microns over 5 microns primer coating including fixing with screws, prepainted iron J or L hooks, bolts and nuts 6mm(six milimetre) dia with prepainted limpet and rubber washer complete with all accessories as required as per specifications and as per direction of Engineer-in-Charge including carriage of materials with in all leads, liftsother incidentals.

Providing and fixing ridges or hips 60 cm (Sixty centimeter) overall with 0.60 mm (Zero point sixty millimeter) thick preprinted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat or regular modified polyester organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with preprinted iron J or L hooks, bolts & nuts 6mm(Six millimeter) dia and preprinted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm (one point sixty six millimetre to two millimetre) thick in eaves board/facia/soffits/ ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Steel work welded in built up sections,trusses and framed work,including cutting, hoisting, fixing in position and applying a priming coat of red lead paint. including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge . In beams joists channels, angles, tee, flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like

In gratings framed guard bars, ladders, railling, brackets and similar works.

6mm (six millimetre) cement plaster 1:3 (1 cement :3 sand) to ceiling finished with a floating coat of neat cement and thick coat of limewash on top of wall when dry for bearing of R.C.C slabs and beams. including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

20mm (twenty millimetre) Cement plaster in single coat on rough side of brick/stone masonry for interior plastering upto floor any level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth Cement Mortar 1:6 (1 Cement :6 sand) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete. including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

15mm (fifteen millimetre) cement plaster in single coat on fair side of brick/concrete/ stone walls for interior plastering upto floor any level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth Cement mortar 1:3 (1 cement:3 sand) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Painting two(excluding priming coat) on new steel and other metal surfaces under coat with ready mixed paint brushing to give an even shade including cleaning the surface all dirt ,dust and other foreign matter with white ready mixed paint including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting Readymixed paint brushing wood primer pink including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Painting two coats(excluding coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping With enamel paint other than white including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing under layer for plinth protection of 75mm (seventy five millimetre) thick (unconsolidated) bed dry brick/stone aggregated 40mm (fourty millimetre) nominal size with rammed and consolidated and grouted with fine sand including preparation of ground including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing plinth protection 50mm (fifty millimetre) thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm (twenty millimetre) nominal size) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Constructing course rubble dressed "U" shape open surface drain with side wall 15X22cm (fifteen into twenty two) in cement mortor 1:6 (one cement: six sand) and in side plstring with cement plaster 1:3 (one cement : three sand ) including earth work and laying 10cm (Ten Centimetre) cement concrete 1:5:10 (one cement :five sand:ten graded stone aggregate 40mm (Forty millimetre) nominal size) and 7.5cm (seven point five centimetre) cement concrete 1:2:4(one cement :two sand ;four graded stone aggregate 20mm (Twenty millimetre) nominal size) and finishing with a floating coat of neat cement and curing complete as per standard design including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Supplying cast iron cover with frame for manhole for frame of internal dimension 455 x 610 mm (four hundred fifty five into six hundred ten millimetre) rectangular CI cover the weight of cover to be not less than 23 kg (twenty three kilogram) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes Finolex ISI marked including fixing with approved adhesive etc. complete. including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge 110 mm (one hundred ten millimetre) dia

75 mm (seventy five millimetre) dia

Providing and fixing PVC cowl ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 110 mm (one hundred ten millimetre) dia PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing vitreous China wash down, water closet squatting pan (Indian type W.C pan) size 580mm (five hundred eighty millimetre) (Earth work, bed concrete, foot rest and trap to be measured and paid for separately) including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing vitreous China wash down,water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) (Seat and over to be measured and paid for separately):- Anglo indian universal closet. including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing G.I inlet connection for flush pipe with W.C pan including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers : Solid type including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing Flat back type of size 430mm x 260mm x 350mm (four hundred thirty millimetre into two hundred sixty millimetre into three hundred fifty millimetre) vitreous China bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with choppe hemp (weste pipe to bemeasured and paid for separately including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing automatic flushing cistern with a pair of C.I. Or M.S. brackets complete with fittings including C.I. Syphonic apparatus, mosquito proof lid, C.P. Brass unions and coupling for connections with inlet, outlet and overflow pipes including cutting holes and making good the same (overflow pipe to be measured and paid for separately) Vitreous China 5 litres capacity including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Providing and fixing 15 mm (fifteen millimetre) nominal bore C.P. brass flush pipe / spreaders for urinal with fitting such as unions, clanmps etc. (all in C.P. Brass) including cutting holes and makng good the same including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Providing and fixing vitreous chinawash basin single hole for pillar tap with CI or MS brackets painted white including cutting holes and making good the same but excluding fitting Size 630x450mm(six hundred thirty into four hundred fifty millimetre) Vitreous china including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing vitreous China padedstal for wash basin complete recessed at the back for the reception of pipes and fittings including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing 32mm (thirty two millimetre) dia C.P. Brass waste for wash basin or sink including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 32mm (thirty two millimetre) dia M.I union for wash basin or sink including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 600mm x 450 mm (six hundred millimetre into four hundred fifty millimetre) bevelled edge miror of superior glass mounted on 6mm (six millimetre) thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 600mm x 20mm (six hundred millimetre into twenty millimetre) C.P. Brass Towell rail coplete with C.P. Brass brackets fixed to wooden pluges with C.P. Brass screws including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing CP brass toilet paper holder including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing charomium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 600mm x 300mm (six hundred millimetre into three hundred millimetre) Vitreous China Division Plate for Urinals including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) dia C.P Brass bib tap with Capstan head including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) dia C.P Brass pillar tap with Capstan head including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) C.P. brass angle valve without nuts and pipe including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 15 mm (fifteen millimetre) dia C.P. stop cocks including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 300/450mm (three hundred per four hundred fifty millimetre) length 15mm (fifty millimetre) nominal bore P.V.C connection with brass unions including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) nominal bore brass full way valve with wheel including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 1216 (16mm O.D. pipe) (sixteen millimetre) Polyethelene-Aluminium-Polyethelene (PE-AL-PE) composite pressure pipe U.V. stablized with carbon black confirming to IS-15450-2004 water supply including clamp at one metre spacing, cutting, fixing and making good the wall etc. but excluding the cost of fittings (internal work) pipes exposed on wall including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. Equal Tees. (i) 1216 (one thousand two hundred sixteen)

Female branch TEE. (i) 1216 x 1216 x 15mm (one thousand two hundred sixteen into one thousand two hundred sixteen into fifteen millimetre)thread.

Female elbows:- 1216 x 15mm (one thousand two hundred sixteen into fifteen millimetre) thread.

Male thread connector 1216 x 15mm (one thousand two hundred sixteen into fifteen millimetre) thread.

Female thread connector:- 1216 x 15mm (one thousand two hundred sixteen into fifteen millimetre) thread.

Couplers 1216 mm (one thousand two hundred sixteen millimetre)

Providing and fixing PE-AL-PE- composite internal seal compression fittings as per IS-15450-2004 for hot water supply such as tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fixing including cutting and making good the walls etc.(This type of fitting to be used for hot water supply only) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. Equal Tees. (i) 1216 (one thousand two hundred sixteen)

Female branch TEE. (i) 1216 x 1216 x 15mm (one thousand two hundred sixteen into one thousand two hundred sixteen into fifteen millimetre)thread.

Female elbows:- 1216 x 15mm (one thousand two hundred sixteen into fifteen millimetre) thread.

Male thread connector 1216 x 15mm (one thousand two hundred sixteen into fifteen millimetre) thread.

Female elbows:- 1216 x 15mm (one thousand two hundred sixteen into fifteen millimetre) thread.

Couplers 1216 mm (one thousand two hundred sixteen millimetre)

Providing and fixing 500 (five hundred) ltr. net capacity PVC water storage tank of ISI : 12701 marked,G.I. inlet and outlet connection, 15mm (fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110 mm X 90 mm (one hundred ten millimetre into ninety millimetre)

110 mm X 75 mm (one hundred ten millimetre into seventy five millimetre)

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110 mm (one hundred ten millimetre) dia.

75mm (seventy five millimetre) dia

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm (three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110 mm (one hundred ten millimetre) dia.

75mm (seventy five millimetre) dia

Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110 mm (one hundred ten millimetre) dia

75mm (seventy five millimetre) dia

Providing and fixing PVC collers ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110 mm (one hundred ten millimetre) dia.

75mm (seventy five millimetre) dia

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110 mm (one hundred ten millimetre) dia.

75mm (seventy five millimetre) dia

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110 mm (one hundred ten millimetre) dia.

75mm (seventy five millimetre) dia

Providing and fixing PTMT Coloured / white high density polythelene / poly propylene 10 (ten) litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm (fifteen millimetre) nominal size PVC ball valve with polythene float,with push button,couplings for connections with inlet, outlet and ovr flow pipe, 40mm (fourty millimetre) dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing PTMT waste coupling of approved quality and colour 32 mm (thirty two millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing PTMT urinal waste coupling of approved quality and colour including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing PTMT jet spray of approved quality and colour with one metre tube including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 100 mm (hundred millimetre)dia cromium plated grating of superior quality for floor, gully or nahani trap including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing stoneware gully trap grade 'A' complete with C.I grating, brick masonry chamber in cement mortar 1:5 and water tight C. I . cover with frame of 300mmx300mm (three hundred millimetre into three hundred millimetre) size (inside) the weight of cover to be not less than 4.53kg (four point fifty three kilogram) and frame to be not less than 2.72kg (two point seventy two kilogram0 Round Mouth Traps 100mmx100mm (hundred millimetre into hundred millimetre) size P or S type including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Constructing man hole with RCC top slab 1:2:4 mix in (One cement:Two sand:Four graded stone aggregate 20mm (Twenty millimetre) nominal size foundation concrete 1:4:8 (One cement:Four sand:Eight graded crushed stone aggregate 40mm (forty millimetre) nominal size inside plastering 15mm(Fifteen millimetre) thick with cement mortar 1:3(One cement: Three sand) finished with a floating coat of neat cement and making channel in cement concrete 1:2:4 mix (One cement:Two sand:Four graded crushed stone aggregate 20 mm (Twenty millimetre) nominal size finished smooth complete curing and testing Inside size 800mm x 800mm (eight hundred millimetre into eight hundred millimetre) and 500mm (five hundred millimetre) deep including C.I cover with frame. (Light duty single seal pattern - 1) 455 mmx610mm (four hundred fifty five millimetre into six hundred ten millimetre) internal dimensions total weight of cover and frame to be not less than 38kg (thirty eight kilogram) . (weight of cover 23 kg (twenty three kilogram) and weight of frane 15 kg (fifteen kilogram)) With 300mm (three hundred millimetre) thick walls of squarred rubble masonry coursed with hard stones of approved quality in cement mortar 1:3 (1 cement : 3 sand). including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Constructing man hole with RCC top slab 1:2:4 mix in (One cement:Two sand:Four graded stone aggregate 20mm (Twenty millimetre) nominal size foundation concrete 1:4:8 (One cement:Four sand:Eight graded crushed stone aggregate 40mm (forty millimetre) nominal size inside plastering 15mm(Fifteen millimetre) thick with cement mortar 1:3(One cement: Three sand) finished with a floating coat of neat cement and making channel in cement concrete 1:2:4 mix (One cement:Two sand:Four graded crushed stone aggregate 20 mm (Twenty millimetre) nominal size finished smooth complete curing and testing Inside size 800mm x 800mm (eight hundred millimetre into eight hundred millimetre) and 1000mm (one thousand millimetre) deep including C.I cover with frame. (Light duty single seal pattern - 1) 455 mmx610mm (four hundred fifty five millimetre into six hundred ten millimetre) internal dimensions total weight of cover and frame to be not less than 38kg (thirty eight kilogram) . (weight of cover 23 kg (twenty three kilogram) and weight of frane 15 kg (fifteen kilogram)) With 300mm (three hundred millimetre) thick walls of squarred rubble masonry coursed with hard stones of approved quality in cement mortar 1:3 (1 cement : 3 sand). including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

Providing and fixing electrical Gyser ISI marked having 35 ltr. Net water capacity with necessary accessories etc. complete including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge .

LALITA SOOD