CONSTRUCTION OF COMMUNITY BUILDING AT T. P. S. No. 5 (City Wall Improvement) (Section – 7) Final Sanc., F. P. No. 26, At: Dariyapur - Kazipur, Taluka: City, District: Ahmedabad, near dariyapur gate dariyapur ward central zone, Ahmedabad

S.No Qty Item Unit Rate Amount

A EARTHWORK AND ALLIED WORK

1 5.00 Demolition and disposal of unserviceable materials

with all leads and lifts for Brick masonary. Rate

also includes necessary tools, scaffoldings and all

safety measures required for the same, including all

leads and lifts. Cmt. 544.95

2 10.00 Demolition and disposal of unserviceable materials

with all leads and lifts for RCC work.Rate also

includes necessary tools, scaffoldings and all safety

measures required for the same, including all leads

and lifts. Cmt. 1047.38

3 100.00 Empty boring holes 3.50 mt depth in ordinary soil

and getting out the soil and disposing the surplus

excavated eart within 50 mtr lead for a) 300 m.m.

dia. Pile Each 1509.00

4 20.00 Extra for under reaming inside the bore Holes for

under reamed piles of following Diameter. (a)

mm. Each 642.30

5 30.00 Extra above over item of boring to the rates of bore

holes of 3.5 mtr if bore are made deeper than

mtr. For a) 300 mm dia. Rmt. 539.34

6 970.00 Excavation for foundation upto 1.50 Mt depth

including sorting out and stacking useful materials

and disposing off the excavated stuff upto

Meters lead (B) Dense or hard soil. Cmt. 259.14

7 970.00 Excavation for foundation 1.50 Mt to

3.0 Mt. depth including sorting out and stacking

useful materials and disposing off the excavated

stuff upto 50 Meters lead (B) Dense or hard soil.

8 323.50 Excavation for foundation 3.0 Mt. to

5.00 Mts. depth including sorting out and stacking

useful materials and disposing off the excavated

stuff upto 50 Meters lead (B) Dense or hard soil.

9 100.00 Filling available excavated earth (excluding rock)

in trenches, plinth, sides of foundations etc. in

layers not exceeding 20 cm. in depth, consolidating

each deposited layer by ramming and watering etc.

complete. Cmt. 129.10

10 10.00 Filling in foundation and plinth with murrum or

selected soil in layers of 20 cm. thickness including

watering, ramming and consolidating etc. complete. Cmt. 286.20

11 10.00 Sand filling with sand as approved by Architect in

plinth / under floor / elsewhere including watering,

ramming, consolidating and dressing to the

required grades and levels as directed by Clerk-of-

Work. Cmt. 455.63

12 2025.0 Anti-Termite System: Providing and laying of

0 permanent piping technology anti-termite

treatment before flooring work by installing LLDP

(Low linear density polyethylene) tube of 8 mm

O.D. & 6.4 mm 1.D. with inbuilt pressure

compensation chip every 30 cm interval in the tube,

having working pressure of 2 Kg/cm2 and release

rate of 1.9 Itr/hour fixed by P-clips and nails. The

LLDP pipe shall be installed at the entire periphery

of the building and at internal network of building

at a depth of 20 to 200 mm under floor at every 2 to

3 mtr. c/c distance (adjusted as per building layout

)& Ends of loop pass through a PVC elbow of

minimum 32 mm ID at junction box of wall and

floor level, entering into a steel reinforced grooved

flexible pipe of minimum 22 mm ID leading into

junction box and the loops shall terminate in

junction boxes & test every junction during

injecting chemicals for termite control treatment.

The anti termite chemical Imidacloprid 30.5% SC

mix as per IS-6313 (part III) shall be injected by the

pressure pump diluted with water @ 10.5 ml/5 ltr of

water at the rate of 2 Kg/sq.cm @ 5 Ltr/SMT. The

contractor shall submit approved line plan for

piping system and junction boxes dully approved by

Engineer-in-Charge with bond of 5 year

warranty.(i)Anti Termite chemical injected area

(Chemical injecting incl. labour cost) Sq. mt 133.00

13 2025.0 Carrying out timber treatment to all woodwork,

0 including drilling holes and spraying oil-based

chemical solution on the surface of timber work for

termite control, including labor and material etc.,

complete. Using Chlorpyriphos20 EC as per

2013 Part III (1% concentration by mass) is

recommended: one litre of chemical emulsion

diluted with 19 litres of kerosene. Total diluted

concentration will be 20 liters, inclusive of 1 liter

chemical emulsion application in drilled holes and

0.75 / Litre chemical per one Sqmt two coat on

wood surface not protected by paint or varnish. Sq. mt 54.98

14 3100.0 Applying general insecticide pest control treatment

0 to floors, cupboardsetc including labour materials

etc. complete. Using Imidacloprid 30.5 SCas Per IS

6313 part -II( (0.075% concentration by mass) is

recommended 10.5ml chemical diluted with 5 liters

of water application 0.5 litre chemical /Sqm of

surface is recommended as per I.S. Sq. mt 88.40

15 600.00 Carrying out plinth treatment to post

construction / existing structure by spraying

chemical solution for termite control treatment,

including labour and material, consistent with I.S.I

specification. Using Chlordene and Chlorpyrifos

EC. As Per 6131_paret-II Concentration Weight

one percent is recommended i.e one litre 20 EC

chemical emulsion with 19 liter give 1 %

concrentration, inclusive of one litre chemical

emulsion application at the rate of 5 Litre chemical

/ Sqm of surface is recommended as per I.S Sq. mt 104.90

16 2690.0 Carrying out wall treatment for termite control,

0 including spraying with chemical solution in oil

base, including labour and material. Using

Chlorpyriphos 20 ECAs per IS 6313 part- II (1%

concentration by mass) is recommended i.e one litre

chemical emulsion diluted with 19 litres of oil base.

Total solution will be 20 liters inclusive of one liter

chemical emulsion application at the rate of

litres chemical / Sqm of surface is recommended as

per I.S. Sq. mt 37.34

17 Conveyance charge of lime , murrum, building

rubbish, earth manure or sludge, and excavated

earth and fly ash

and any kind of debris etc. complete. No dry factor

for this item shall be calculated.

a 800.00 a) Upto lead of 5 Kms. Cmt. 235.51

b 300.00 b)Conveyance Charge (Extra Rate) above

5.00 Km and Up to 10.00 Km. Cmt. 350.00

B CONCRETE AND ALLIED WORK

18 100.00 Providing and laying cement concrete 1:3:6 (1-

Cement : 3 - Coarse aggregate : 6-Hand broken

stone aggregates 40 mm nominal size) and curing

complete excluding formwork in (A) Foundation

and plinth. Cmt. 4700.00

19 550.00 Providing and laying in situ controlled Reinforced

Cement Concrete of Mix M20 grade using cement

of OPC and 20mm and down size machine crushed

black trap of approved coarse aggregate and fine

aggregates confirming to IS: 383 - 2007, by

concrete batch mix plant, weight batch machine

mixed and machine vibrated design mixed concrete,

including design of concrete mix and shall be

confirming to latest IS : 456, IS : 10262 :

SP23 & SP24 with minimum cement content of

Kg per CUM of concrete and if necessary adding

admixtures in recommended proportions as per IS :

9103 as retarding admixture to retard setting of

concrete and or water reducing admixture to

maintain workability with reduced amount of water

and to improve durability without impairing

strength of concrete for any type, any shapes and

any sizes of reinforced cement concrete structural

members and mass concrete such as..........for

foundation, raft, retaining wall, column, pedestals,

ground/plinth beam, beam, suspended slab, coping,

wall lintel , weather shed, chajjas, lofts, steps and

waist slab of staircase, platform, canopy, peragolas,

parapet, dropwall, window cills, mullions, facia,

fins, gutter, bed block, ramp, overhead and under

ground water tank........etc., as shown in the

drawings and specifications for all sectionc in all

position for including mixing, transporting,

pumping and placing (pouring), hoisting, necessary

scaffolding, vibreting , finishing evenly, watering,

levelling, roughening and or hacking concrete at

construction joints, leaving pockets and holes,

keeping drip moulds, grooves, including curing,

testing etc.with rigid and waterlight centering and

shuttering as ordinary formwork using steel /

plywood shuttering materials for horizontal, vertical

and inclined membe of rectangular, square, round,

hexagonal, octagonal or curved shape, including

necessary propping, scaffolding, bracing, shorig,

strutting, bolts, fastener nails etc; and keeping the

same in position during and after concreting and

careful stripping / careful removal of the same at

and up to appropriate time, applying approved

shuttering oils and by approved manner will prior to

placing the reinforcing steel in position to ptevent

the adhesion of concrete to form work etc. complete

and as directed and specified by PMC /

ARCHITECT / ENGINEER.

(1) The Concrete Mix Design shall be done by the

CONTRACTOR in testing laboratory approved by

PMC / ARCHITECT / ENGINEER with the

Maximum Water Cement ratio shall be limited to

(2) The concrete design mix shall be of without

/ using of Admixtures / Additives to achieve the

desire strength etc; and it shall be not paid extra.

(3) Rate EXCLUDES providing and installing

Reinforcement Steel, conduits, sleeves and inserts

& form work-Shuttering and Centering.

(4) If in Concrete Mix Design Fly Ash is allowed to

use with OPC cement - use of Fly Ash as maximum

25 % by weight of total cementatious material to

replace by Fly Ash conforming to IS : 3812 -

(Latest), than Price Difference between OPCement

and Fly Ash shall be discounted / adjusted in next

bill. Cmt. 11500.00

20 273.10 -Do- as per above item but from below ground

level to Ground Floor Slab level Cmt. 12500.00

21 353.00 -Do- as per above item but from Ground floor Slab

to First Floor Slab level Cmt. 13500.00

22 307.00 -Do- as per above item but from First floor Slab to

Third Floor Slab level Cmt. 13500.00

23 313.00 -Do- as per above item but from THird floor Slab

to Fifth Floor Slab level Cmt. 13500.00

24 790.25 Extra for M

25 1005.8 Extra for M

26 142 Providing TMT Bars FE- 550 reinforcement for

000.00 R.C.C. work including bending, binding and

placing in position complete upto floor two level. Kg 75.46

27 Providing, laying and fixing in position galvalume

pre painted and pre coated (PPGA) trapezoidal

profile sheets (size, shape and pitch of corrugation

as approved by PMC / ARCHITECT / ENGINEER)

with special male / female side laps and anti

siphoning feature at male and to prevent leakage

made from high tensile strength - 345mpa / 500mpa

GALVALUME steel and AZ-150gsm Zincalume

coating to total on both side as per ASTM

(55% aluminium + 43.5% zinc and 1.5% silicon)

having sheet 0.55mm TCT at top and base metal

thickness 0.48/0.5mm including colour coating of

20 micron finish coat over 5 micron primer coat on

exposed side and back coat of 5 microns over a

primer coat of 5 microns and having protective gard

film of 25 micrones to avoid stretches while

handling the sheet and upto erection process for

roofing and side clading, approved make and

approved shade, for roofing at all levels and heights

including cutting sheets and drilling the holes with

side laps as required and end laps 150mm to

200mm including fixing by self tapping and self

drilling 8 mm dia x 55mm long SDST screw of

'BUIDEX' orcorroshield make as per AS -

class-3 with EPDM seal, washer of 25mm dia 3mm

thick bitumen washer with 6mm central hole to

form water proof joint etc. and using templates as

suggested by manufacturer to ensure proper side

laps for any pitch in horizontal and verticle or

curved surface, etc. complete and as directed and

spaecified by PMC / ARCHITECT / ENGINEER.

a 480. do as per above item but for roofing monitors from

00 0.50 mm thick Sq. mt 650.00

b 56.0 do as per above item but for roofing monitors from

0 0.50 mm thick Rmt. 775.00

C MASONARY AND PLASTER WORK

28 5.09 Brick work using common burnt clay building

bricks having crushing strength not less than

kg/Sq. cm. in foundations and plinth in cement

mortar 1:5 (1 cement :5 fine sand) for conventional

type bricks. Cmt. 4011.66

29 50.0 Extra rate over above item 37 Brick work using

0 common burnt clay building bricks having crushing

strength not less than 35 kg/Sq. cm. in cement

mortar 1:6 (1 cement :6 fine sand) for

superstructure upto floor three level height. For

conventional type bricks. (a) For Superstructure

above plinth level upto floor two level

(B) Conventional. Cmt. 4284.21

30 170. Extra rate over above item 37 and 38 Brick work in

00 super structure above floor two level over and

above the above item of brick work in

superstructure (B) Conventional. Cmt. 4324.00

31 50.0 Half Brick masonary in common burnt clay

0 building bricks having crushing strength not less

than 35 Kg/Sq. Cm in Cement Mortar 1:4 (1-

Cement : 4- Coarse Sand) in superstructure above

plinth level for any level and height.

(B) Conventional Bricks. Sq. mt 633.99

32 269 Providing and applying double coat waterproof

0.00 cement plaster (mala finish) on internal surfaces in

two layers, including surface preparation, mixing

approved integral waterproofing compound, curing,

scaffolding, etc. complete.First coat: 10–12 mm

thick in CM 1:4 with waterproofing

compoundSecond coat: 6–8 mm thick in CM 1:3

with waterproofing compound (mala

finish)Finished smooth and even, true to line and

level. Sq. mt 366.12

33 156 Providing and applying 15–20 mm thick stucco

7.00 plaster in cement mortar (1:3 / 1:4) in two coats,

including surface preparation, scaffolding, finishing

to the desired texture, curing, and all leads & lifts

complete as per specifications. Sq. mt 950.00

34 156 Providing 20 mm thick double coat mala / sandface

7.00 cement plaster on brick/ concrete work for

plastering comprising of base coat of 12 mm thick

cement plaster in cement mortar (1 Cement :

Coarse Sand) in rough finishing and 8 mm thick top

coat of cement mortar 1:2 (1 Cement : 2 Coarse

Sand) finished with trowel including scaffolding

curing etc. complete. Sq. mt 394.02

35 150 Providing and fixing 23 cms wide chicken mesh

0.00 jaali with nails & then application of 15 mm plaster

on R.C.C. &Masonary joints as per directed of

Engineer in Charge Sq. mt 210.00

D STRUCTURE STEEL AND ALLIED WORK

36 143 Providing, Fabricating, Transporting and Erecting

10.00 in position at all levels as per drawing welded /

bolted / riveted steel structures with field bolting /

riveting / welding / drilling whebever necessary and

finally full welde after completting erecting work,

applying one coat of rust remover one coat of anti -

corrosive red oxide paint or yellow zinc chromate

and three or more coats of approved make and

shade flat / enamle / aluminium paint to give even

shade etc, as directed and specified with necessary

gusset plates, base plates, base plates, battened

plates, cleats, etc. complete as per design and as

directed and specified by PMC / ARCHITECT /

ENGINEER. (a) Gusset plates will be measured

and actual and paid for.

(b) Weight of bolts , nuts, washers, rivets and

welding will not be considered and paid for.

(c) The measurements of rolled sections shall be

taken in length and area and the weight will be

computed as per standard steel tables, Rolling

margin and wastage if any will be to contractor's Kg 126.68

(d) Rate includes for any Rectifications and minor

works to be carried out etc. cpmplete.

37 280 Providing and fixing M.S. grills of required pattern

0.00 to wooden frames of windows etc. with M.S. flats

at required spacings and frame alround, square or

round bars with round headed bolts and nuts or by

screws. (B) ORNAMENTAL GRILL pattis, and all

other visible wooden pattis with melamine polish of

approved brand and procedure. KG 143.64

E PAVING AND FLOOR FINISH WORK

38 75.0 Providing and laying marble stone slab flooring

0 over 20mm (average)base of cement mortar 1:6 (1-

cement : 6 coarse sand) or L.M. 1:1.5(1- lime putty

: 1.5 - coarse sand) laid and jointed with gray

cement slurry including rubbing and polishing

complete. (A) Marble slab 25mm thick Sq. mt 2267.88

39 59.0 Providing and laying polished kota stone slab

0 25mm thick in risers of steps,skirtingDedo and

pillars laid on 10mm thick cement mortar 1:3 (1-

Cement : 3 coarse sand) and jointed with gray

cement slury mixed with pigment to match the

shade of slab including rubbing and polishing etc.

complete. Sq. mt 1214.30

40 120. Providing and laying Vitrified tiles 8 to 10 mm

00 thick , 36'' x 36'' in flooring treads of steps and

landing laid on a bed of 12mm thick cement mortar

1:3 (1-cement : 3-coarse sand ) finishing with flush

pointing in white cement. Sq. mt 1516.65

41 75.0 Providing and laying Vitrified tiles 8 to 10 mm

0 thick , in skrting risers of steps and dedo on 10mm

thick cement plaster 1:3 (1-cement : 3-coarse sand)

and jointed with white cement slurry Sq. mt 1103.06

42 110. Providing and laying broken china mosaic flooring

00 for terrace using 12 mm to 20 mm broken pieces of

glazed tiles to be laid over cement mortar 1:3 to

plain or slope and to be tempered to bring mortar

creme out upto surface using white cement

including rounding off junctions and extending

them upto 15 cm along the wall,clearing with water

and oxalic acid etc. as directed. Sq. mt 771.98

43 50.0 Providing and laying white or golored glazed tiles

0 of the size 300 mm x 200 mm x 8 mm / 300 mm x

450 mm x 8 mm in skirting, risers of steps and dedo

on 10 mm. thick cement plaster 1:3 (1 cement :

coarse sand) & jointed with white cement slurry.

44 910. Providing & fixing heritage cement / Athangudi

00 tiles in COMMUNITY HALL ,EVENT HALLS,

MEETING ROOMS including base preparation,

polishing & sealing Sq. mt 2250.00

45 300. Providing & fixing heritage patterned vitrified tiles

00 (Moroccan/Jaipur design) in150mm border along

with kotah stone in PASSAGES AND FOYER

AREA Sq. mt 2250.00

46 450. Providing and fixing Kota stone flooring of

00 approved green and brown shades in leather finish

(machine brushed anti-skid texture), 20–25 mm

thick,laid over 20 mm thick cement mortar bed

(1:4), including dressing of edges,jointing with

cement slurry mixed with matching pigment,

curing, and cleaning and sealing is complete.in

PASSAGES AND FOYER AREA Sq. mt 1750.00

47 377. Providing and Fixing 16 mm thick Kota stone

00 skirting of 100 mm height with C.M. 1:4 (1

Cement:4 Sand) in good line and level Rmt 180.00

48 40.0 Providing & fixing 15 mm thick kadappa stone riser

0 in the STAIRCASE including polishing Sq. mt 1250.00

49 80.0 Providing & fixing 15 mm thick Jaisalmer stone

0 steps in STAIRCASE including polishing Sq. mt 1800.00

50 110 8 mm thick Vitrified Skirting (100 mm height)

0.00 matching the flooring Rmt 350.00

51 120. Providing & laying 8 mm thick vitrified tile

00 flooring complete in male female toilet area Sq. mt 1350.00

52 240. Providing & fixing 8 mm thick vitrified tile skirting

00 100 mm height in male female toilet area Rmt 180.00

53 39.0 Providing and fixing 12 mm thick wooden flooring

AND GREEN ROOMS Sq. mt 4262.00

54 90.0 Providing and laying integral cement based water

0 proofing treatment Average 120 mm thick

including preparation of surface as required for

treatment of roof, balconies, terraces etc. and

making necessary vata at the junction of Wall and

floor wherever required as directed by Engineer In

Charge and consisting of following operation

.Applying and grouting a slurry coat of neat cement

using 2.75 kg/Sq.Mt. Of cement admixed with

proprietary water proofing compound conforming

to IS .2645 over the RCC slab including cleaning

the surface before treatment. Laying cement

concrete using broken bricks/brickbats25 mm to

100 mm size with 50% of cement mortar 1:5 (

cement , 5 coarse sand)admixed with proprietary

water proofing compound conforming to IS

over 20 mm thick layer of cement mortar of mix 1:5

After two days of proper curing applying a

second coat of cement slurry admixed with

proprietary water proofing compound confirming to

IS 2645 Finishing the surface with 20 mm thick

jointles cement mortar mix 1:4 (1 cement, 4 coarse

sand) admixed with proprietary water proofing

compound conforming to IS: 2645 and finally

finishing the surface with trowel with neat cement

slurry and making of The whole terrace so finished

shall be flooded with water for a minimum period

of two weeks for curing and for final test.all above

operations to be done in order and as directed and

specified by Engineer -In- charge Sq. mt 1890.00

55 110. Providing and laying cement concrete flooring

00 1:2:4 (1 Cement : 2 Sand : 4 graded stone

aggregates 20 mm nominal size) laid in one layer

and finished with a floating coat of neat cement (A)

50 mm thick. Sq. mt 435.00

56 110. Providing and layingbrick bat koba concrete for

00 china mosaic bedding Sq. mt 750.00

57 100. Providing and Laying of Rubber Moulded Paver

00 Block Grey/Coloured 60 mm thick, M-35 Grade of

any size ; shape (Usually Uni-Paver Blocks) using

black trap good quality aggragate of 20 mm

nominal size for footpath, parking areas, service

lanes and other areas as mentioned in the drawing /

instruction of engineer in charge. Cost includes

formworks using rubber mould,providing and

laying paver blocks as per required grading and

specification. The paver block shall be

mechanically compacted. The work of paving

blocks shall be executed in line and level by skill

mason of flooring work only. It should be laid in

such a way that the no cutting of the paver block to

be necessary. if cutting of paver block necessary

then it should be cut by machine only and carting.

The finished surface of the paver block shall have

resonably good, plain finished. Paver blocks shall

be compacted and shall be relaid if necessary.

Gravel or such type of materials shall not be

allowed for production. Laying on 5 cms thick sand

bedding Sq. mt 501.60

58 100. Providing and fixing pre-cast concrete kerb stone of

00 gray cement based concrete block 30 cm length x

30 cm heigh and 75 cms thick of M-200 grade

concrete as per approved design and including

excavation for fixing in proper line and level, filling

the joints in C: M 1:3 (1 Cement : 3 Fine sand) etc.

complete. Rmt 328.00

F PAINT AND POLISH WORK

59 180 Providing & Applying two coat of white putty of

0.00 Birla or equivalent at all levels to internal plaster

surfaces/POP surfaces of concrete, masonry work

including jambs, sills, grooves, pattas, rounding of

corners after thoroughly brushing the surfaces free

from mortar dropping and other foreign matter and

also including preparing the surface even and sand

papered smooth etc. after applying every coat of

putty. Priming coat of alkali resistant cement primer

(water or solvent based) is to be applied before at

all levels, all floors, all height, all complete as per

drawing, specifications, instruction & directions of

the Engineer-in-charge. Payment shall be done as

per drawing/laid at site of plastered area. Approved

Brands : J.K. White, Birla, Asian. Sq. mt 40.19

60 100. Painting two coats (excluding priming coat) on new

00 steel and other metal surface with enamel paint,

brushing, interior to give an even shade including

cleaning the surface an even shade including

cleaning the surface of all dirt, dust and other

foreign matter. Sq. mt 86.94

61 100. Painting one coat extra on new steel and other metal

00 surface with enamel paint, brushing, interior to give

an even shade including cleaning the surface an

even shade including cleaning the surface of all dirt,

dust and other foreign matter. Sq. mt 50.40

62 150 Painting two coats (excluding priming coat) on new

0.00 wood and other wood base surface with enamel

paint, brushing, interior to give an even shade

including cleaning the surface an even shade

including cleaning the surface of all dirt, dust and

other foreign matter. Sq. mt 104.12

63 180 Wall painting (Two coats) with plastic emulsion

0.00 paint of approved brand and manufacture on

undecorated wall surface to give an even shade

including thoroughly brushing the surface free from

mortar droppings and other foreign matter and sand

papered smooth. Sq. mt 140.00

64 180 Finishing wall with weather proof exterior emulsion

0.00 paint on wall surface (two coats) to give an required

shape even shade after thoroughly brushing the

surface to remove all dirt, and remains of loose

powdered materials.etc complete Sq. mt 113.40

65 15.0 Providing and fixing exterior grade teak wood

0 door/window frames made from well-seasoned

timber having a moisture content of 12–15%,

including machining, rebates, mortise-tenon joints,

preservative treatment to concealed surfaces,

stainless steel holdfasts, fixing in masonry, and

finishing smooth complete as per drawings and 200000.0

specifications. Cmt. 0

66 10.0 Providing and fixing teak wood external door

0 shutters of approved thickness and design

including styles, rails, panels or glazing provision,

waterproof adhesive joints, machining, sanding,

preparation for hardware and application of

approved exterior wood finish complete as per 190000.0

drawings and specifications. Cmt. 0

67 6.50 Providing and fixing carved teak wood pillar /

column including base, shaft and capital as per

architectural drawings, complete with carving work,

machining, stainless steel anchoring arrangement,

preservative treatment, sanding and exterior 211860.0

protective coating. Cmt. 0

68 3.00 Providing and fixing decorative wooden brackets

/ fascia made from seasoned hardwood including

shaping, joinery, anchoring to structural support,

preservative treatment and exterior finish complete

as per architectural details. Cmt. 0

69 50.0 Wooden handrail as per design for the staircase

0 Made out of hard wood (teak,sal)with pu polish Rmt. 6000.00

H CEILING AND GLASS WORK

70 195. Providing and fixing sheet glass, selected quality

00 (Type-C) bedded in putty and fixed with wooden

beading, including the cost of wooden beadings of

first-class teakwood and necessary cutting of glass.

(2) 6 mm thick. Sq. mt 1176.10

71 21.0 Providing and fixing glazed louvered glass

0 windows and ventilators with teak wood frame

10cm. x 7cm. size including 3 coats of oil painting

to wood work etc.complete. Sq. mt 4102.54

72 550. Providing and fixing PVC printed false ceiling

00 with flush type with alluminium frame, frame work

is done with three different sections of G.I. sheet of

24 gauge thickness named as C, U and L. The C

section is fixed with hangers at an equal distance of

36” each and then U section is fixed perpendicular

on C section with steel screws at and equal distance

of 16” each. The complete frame work is supported

by G.I. L angle/6 mm rod hangers from the roof and

L sections is fixed all around the wall as shown in

the diagram. 5mm PVC sheet strips of size 2 wide

are fixd with counter sunk steel screws on the U

section. Further 3mm PVC sheet is stuck to these

PVC strips with solvent cement such that joining

lines are perfectly matched. P.U. putty is filled,

dried and leveled and requisite coats of primer and

paint is done on the ceiling for getting fine surface

finish etc. complete as per direction of Engineering

and charge manufacturer’s specification and

drawing. Sq. mt 902.00

73 550. Providing and fixing wooden planks ceiling with

00 tounged and grooved jointing and wood screws

(frame work and cover fillings to be measured and

laid for separately) (A) Indian Teak wood (iii)

25mm thick Sq. mt 1792.68

74 15.0 Providing and fixingM.S. Fan clamps type 1 to

0 16mm dia M.S. bar bent to shape with hooked ends

to R.C.C. slabs curing, laying including painting the

exposed portion of loops, all as per standard design

complete. Eac h 130.98 11011 11.21 Extra over rate

of item 20 for providing and fixing M.S. fan clamps

type-II as per standard design in R.C.C. beams

during laying towards additional height of the

clamp due to beam rib. Cm Height 1.49

11.23 Providing and fixing M.S. round holding

down or anchor bolts with nuts and washer plates

complete. Each 124.74

75 550. Providing and fixing wooden false ceiling including

00 framework, ceiling boards, suspension system,

finishing and all complete as per drawings and

directions of Engineer-in-Charge.Framework to be

fixed true to line, level and plumb. Grid spacing

600x600 mm. Boards fixed with screws. Provide

cut-outs for services. Framework: Seasoned

wooden battens 50x25 mm or GI sections. Boards:

12 mm BWR/BWP plywood. Suspension: MS rods

6–8 mm dia. Finish: Veneer/laminate/ PU polish.

Fasteners: SS/GI screws. Sq. mt 3140.00

I GFRP AND ROOFING WORK

76 68.0 Providing and fixing Glass Fiber Reinforced

0 Polymer (GFRP) elements of approved design,

shape, size, and pattern as per drawings and

instructions of the Engineer-in-Charge.The GFRP

shall be manufactured using isophthalic

polyester/vinyl ester resin reinforced with E-glass

fiber, produced through hand lay-up or spray-up

process in approved moulds.The minimum

thickness of GFRP elements shall be 5 mm, unless

otherwise specified.The outer surface shall have a

UV-resistant gel coat finish, smooth or textured as

per the approved sample. The material shall be

resistant to weathering, moisture, and temperature

variations.The GFRP panels shall be fixed over MS

structural framework (minimum 40x40x3 mm)

anchored to the base structure using approved

anchor fasteners. Panels shall be fixed using SS

screws, rivets, or adhesive as required.All joints

shall be properly sealed using weatherproof silicone

sealant.The rate shall include:Cost of materials,

labour, moulds Transportation, loading/unloading

Scaffolding and installation All leads and lifts

Finishing and cleaning. Complete work shall be

executed as per approved drawings and sample, to

the satisfaction of the Engineer-in-

Charge.Submittals Required Shop drawings

Material test certificate Sample panel (mock-up) Sq. mt 88275.00

77 550. Stone-coated roof tiles fixing over an aluminium

00 sheet, including accessories Sq. mt 3500.00

78 110 Providing & fixing aluminium roofing sheet

0.00 mm thick with 50 mm thick rock wool insulation,

including fasteners, sealants, overlaps, flashing,

complete Sq. mt 2600.00

79 121 Providing, Fabricating, Transporting and Erecting

00.00 in position at all levels as per drawing welded /

bolted / riveted steel structures with field bolting /

riveting / welding / drilling whebever necessary and

finally full welde after completting erecting work,

applying one coat of rust remover one coat of anti -

corrosive red oxide paint or yellow zinc chromate

for MS truss including erection Kg 120.00

80 385 Providing, Fabricating, Transporting and Erecting

0.00 in position at all levels as per drawing welded /

bolted / riveted steel structures with field bolting /

riveting / welding / drilling whebever necessary and

finally full welde after completting erecting work,

applying one coat of rust remover one coat of anti -

corrosive red oxide paint or yellow zinc chromate

for Purlins Kg 110.00

81 100. Providing and fixing GI/Aluminium gutters having

00 section 400 mm wide and 150 mm deep with

mm thick sheet Rmt 800.00

82 28.0 P&F PVC Downpipes of 100 mm dia 4 Kgf/sqcm

83 120. Flashing & ridge caps

84 480. Providing, laying and fixing in position galvalume

00 pre painted and pre coated (PPGA) trapezoidal

profile sheets (size, shape and pitch of corrugation

as approved by PMC / ARCHITECT / ENGINEER)

with special male / female side laps and anti

siphoning feature at male and to prevent leakage

made from high tensile strength - 345mpa / 500mpa

GALVALUME steel and AZ-150gsm Zincalume

coating to total on both side as per ASTM

(55% aluminium + 43.5% zinc and 1.5% silicon)

having sheet 0.55mm TCT at top and base metal

thickness 0.48/0.5mm including colour coating of

20 micron finish coat over 5 micron primer coat on

exposed side and back coat of 5 microns over a

primer coat of 5 microns and having protective gard

film of 25 micrones to avoid stretches while

handling the sheet and upto erection process for

roofing and side

clading, approved make and approved shade, for

roofing at all levels and heights including cutting

sheets and drilling the holes with side laps as

required and end laps 150mm to 200mm including

fixing by self tapping and self drilling 8 mm dia x

55mm long SDST screw of 'BUIDEX' or

corroshield make as per AS - 3566 class-3 with

EPDM seal, washer of 25mm dia 3mm thick

bitumen washer with

6mm central hole to form water proof joint etc. and

using templates as suggested by manufacturer to

ensure proper side laps for any pitch in horizontal

and verticle or curved surface, etc. complete and as

directed and spaecified by PMC / ARCHITECT /

ENGINEER. for roofing 0.50 mm thick Sq. mt 650.00

85 56.0 Do as per above item but for ridge about 500 mm

0 wide having 0.50 mm thickness Rmt 775.00

J PLUMBING AND SANITARY WORK

(Supply,Installation,Testing&Commisioning)of C

PVC (SDR-11) water supply, comprising of

necessary fittings like ,elbows ,tees, unions,

reducers, coupling , pipe nipples etc.comp.

confirming to relevant ASTM D standards

necessary brass threaded male / female adaptors or

elbows necessary clamps or hangers of approved

make and made out heavy FRP channel, Zinc

Coated L clamp, G.I U clamp covered with EPDM

or Silicon rubber and Anchor fasteners etc.comp

Zari cutting with el.grinder& finishing the same in

wall or floor for concealing the pipe line jointing

materials like solvent cement along with primer

base of solvent of pipe and fitting supplier's

a 25.0 20 mm dia. (NB) pipe line

b 55.0 25 mm dia. (NB) pipe line

c 75.0 40 mm dia. (NB) pipe line

d 15.0 50 mm dia. (NB) pipe line

87 Providing and Fixing PVC SWR Pipes and Fittings,

solvent fix 6kg/cm2, confirming to IS4985 and

IS7834 including all fixtures such as Couplers,

Elbows, Tees, etc...

a 24.0 40 mm dia. (OD) pipe line

b 191. 110 mm dia. (OD) pipe line

c 15.0 160 mm dia. (OD) pipe line

d 10.0 200 mm dia. (OD) pipe line

88 SITC of C PVC/U PVC Ball Valve for water

supply pipe line. comprising of Jointing materials

like solvent cement along with primer base of

solvent of same company make only

a 2.00 C PVC ball valve of Heavy duty confirming to

relevant ASTM D standards 40 mm dia. (NB) pipe

line Nos. 1000.00

89 Providing and Fixing Eurpean Type W.C. of

following make and model

a 16.0 Providing and Fixing Concealed flush tank

0 comprising of Nos. 6300.00

Providing and Fixing Concealed flush tank with

upper plate (Jaquar cat.No.JCS-JCS-WHT-2400

and Plate Cat.no.JCP-CHR-352415)

making necessary Brick masonry wall (approx.

1000x600*150mm thick) with single coat of plaster

to concealed the flush tank with chair bracket as per

architectural design

b 16.0 Providing and Fixing ewe wall mounting suite with

0 proper line, level (Jaquar cat.No.CNS-WHT-

961SPP with seat cover) Nos. 11000.00

c 16.0 Providing and fixing Health Faucet with one metre

0 long easy flex tube in chrome finish and wall

flange(cat.No - ALD-563) Nos. 1500.00

d 16.0 Providing and fixing toilet paper holder:C.P.

0 brass( Cat . NO- CAN-1153S) Nos. 1500.00

90 Providing and Fixing Washbasin of following make

a 13.0 Providing and Fixing wash basin above counter

0 type comprising of. Nos. 12500.00

Providing and Fixing waste coupling and Bottle

trap for wash basin (Jaquar cat.No.FLS-WHT-

Making Hole for waste coupling- Pillar Cock or

basin mixer on platform

Providing and Fixing waste coupling

(Jaquarcat.No.ALD 705 L 130)

Providing and Fixing bottle trap

(Jaquarcat.No.ALD 769 L 300/190)

b 13.0 Providing and Fixing Pillar Cock comprising of.

Providing and Fixing Pillar Cock (Jaquar

cat.No.FLR-5011N)

Providing & Fixing necessary 450mm long Braided

hose with nut and washer of Jaquar make ALD-

c 13.0 Providing and fixing liquid soap container (Cat No-

d 13.0 Providing and fixing PTMT towel ring. (Cat No -

0 CAN 1121BN) Nos. 1200.00

Providing and fixing mirror of superior glass (of

approved quality) and of required shape and size

with plastic moulded frame of approved make and

shade with 6 mm thick hard board backing :

e 13.0 Rectangular shape (Cat No - AKP-35795)

91 Providing and Fixing Urinal of following make and

a 12.0 Providing and Fixing Sensor type urinal flushing

0 system comprising of. Nos. 21300.00

Providing and fixing white vitreous china flat back

or wall corner type lipped front urinal basin (Cat

No- URS-WHT-13257)

Providing Sensor type Urinal flushing system of

jaquar make cat. No SNR-STL-51087

Fixing sensor type flushing system at proper

location with necessary concealed box fittings etc.

b 12.0 Providing and fixing Bottle Trap (Cat No- ALD

c 12.0 Providing and Fixing waste coupling

0 (Jaquarcat.No.ALD 705 L 130) Nos. 825.00

92 Providing and Fixing S.S. Kitchen Sink of

following make and model

a 2.00 Providing and Fixing Stainless steel sink made out

of 1mm thick Nirali make Popular Range, Large

having Bowl size 460 x 460 x 230 mm, comprising

of. Nos. 8000.00

Providing & Fixing brackets

b 2.00 Providing and Fixing wall mounted sink cock with

regular swinging spout comprising of. Nos. 2600.00

Providing and Fixing wall mounted sink cock with

regular swinging spout (Jaquar cat.No.FLR-5347N)

Providing & Fixing necessary heavy C P flange &

extension nipple heavy of Viking or Eq.make with

c 2.00 Providing and Fixing Angle Cock comprising of. Nos. 1500.00

Providing and Fixing Angle Cock ( Jaquar

cat.No.FLR-5053N)

Providing & Fixing necessary heavy C P flange &

extension nipple heavy of Viking or Eq.makewith

d 2.00 Providing and fixing Bottle Trap (Cat No- ALD

93 42.0 110x110mm dia.(OD) Deep Seal P trap having

0 water Seal not less than 50mm Nos. 680.00

94 Providing and Fixing Pumps & Pressure System

a 1.00 Submersible Twin Pump System using Grundfos

Make Openwell Submersible Pumps,

2 Pumpsets (1W + 1S),Each Motor Rating : 1.5kW

(2 HP), Three PhaseSystem Rating : 3.0kW (4 HP),

Three PhaseEach Pump : Flow 122 LPM @ 39 Mtr.

Delivery HeadSystem : Flow 244 LPM @ 39 Mtr.

Scope of Supply:Horizontal Submersible Pumpsets

- 2 Nos., Multi Pump Controller - 1 Nos., Float /

Magnetic Sensor - 2 Nos.incl. of Material Handling

& Commissioning Charges

Controller Features:One Working One Assist

Operation With Auto Cascading (Alternating

Logic) of Pumps, Over Load / Dry Run Protection,

Digital Display, On - Off Timer & Hooter

Connection AU 0

b 1.00 Pressure Booster System Grundfos Make HYPN

Booster System - Single VFD

2 Pump + Motor sets (1W + 1S),

Each Motor Rating : 1.5 kW, Three Phase, IE

System Rating : 3.0 kW, Three Phase, IE

Each Pump : Flow 10 M3/hr @ 30 Mtr. Delivery

System : Flow 20 M3/hr @ 30 Mtr. Delivery Head

Pump M.O.C.: Base - CI, Impeller & Chamber - SS

Scope of Supply:

Pump with Motor - 2 Nos, Pressure Transmitter -

Nos, Non Return Valve - 2 Nos, Isolating Valve -

Nos, Pressure Gauge - 1 Nos, Base Frame (MOC :

MS, CED Coated) - 1 Nos, Suction and Discharge

Manifolds (MOC : MS, CED Coated) - 1 Nos,

Single VFD Pump Controller - 1 Nos, 100 Ltr.

Pressure Tank – 1 Nos., Dry Runing Protection

Sensor for UG tank - 1 Nos. AU 520000.00

95 6.00 Providing and fixing in position cowl vent to pipes.

(B) 75 mm diameter. Nos. 450.00

96 6.00 Providing and fixing in position cowl vent to pipes.

(C) 110 mm diameter. Nos. 600.00

97 10.0 Providing and fixing 12 mm dia C.P. bib cock of

0 approved make like jaquar or Essess or any other

type and make specified by the Architect. All pillar

cocks, stop cock, angle cock etc to be Jaquar or

EssEss make with quarter turn disc ceramic

cartridge and chrome finish. Nos. 1500.00

98 4.00 Providing and fixign S.W. gully trap with C.I.

grating brick masonary chamber and water tight

C.I. cover with frame of 300 mm x 300 mm size

(inside) with standard weight (i) Square mouth

traps. (A) 100 mm x 100 mm size P- Type. Nos. 1997.22

99 4.00 Constructing chamber of following size including

excavation, refilling, BBCC (1:5:10) for

foundation, Cement concrete channel(1:2:4)

finished with 15 mm thick cement plaster inside in

cement mortar 1:3, finished with cement slurry,

brick masonary in C.M. 1:5 and excluding the cost

of chamber seat cover etc. complete. (ii) for size

600 x 750 mm inside clear for depth

0.00 to 900 mm for pipe dia<= 200 mm diameter. Nos. 7109.35

100 500 Construction of under ground tank with 23 cm

00.00 thick Masnory wall in c.m. 1:6 incl. Excavation,

necessary 23 cm P.C.C. in 1:4:8 for foundation and

providing R.C.C. 1:2:4 for top slab ( 150 mm thick

& bottom slab (120 mm. thick). Also having

mm. thick R.C.C.(1:2:4) paradi on internal face of

periphery walls. Rate includes all necessary

formwork, T.M.T. steel reinforcement as per given

design, vibrating,curing, & mixing of approved

water proofing material 1 Kg. of chemical with

every 50 Kg.bag of cement ,inside plaster in C.M.

1:3 and vatta in C.M.1:1 inside the tank. Providing

and fixing F.R.C. frame & cover of size 600 x

mm , F.R.P. steps etc. comp as directed. This

includes making Two tanks of various capacities. Litre 30.00

101 250 Construction of overhead tank with R.C.C. 1:2:4

00.00 pardi and top slab Rate includes all necessary

formwork, T.M.T. steel reinforcement as per given

design, vibrating,curing, & mixing of approved

water proofing material 1 Kg. of chemical with

every 50 Kg.bag of cement ,inside plaster in C.M.

1:3 and vatta in C.M.1:1 inside the tank . Providing

and fixing F.R.C. frame & cover of size 600 x

F.R.P. steps etc. comp as directed. Litre 20.00

PART -C (ELECTRICAL ITEMS)

CHAPTER - I WIRING

SECTION - 1-2 Point wiring in Copper (MODULAR)

1 Point wiring for secondary light point with 2-1.5 sq.mm

&earthwire of 1.5 sq.mm (green) both are of ISI marked

KV grade FRLS PVC insulated multistrand copper wires, in

following type of pipe to be erected concealed in / flushed on

wall/ceiling, complete with earth continuity and necessary

connection with primary light with accessories erected on

Metal / PVC box covered with 3 mm thick PC(Polycarbonet) /

Acrylic sheet for open / concealed wiring. with necessary

Lamp holder / ceiling rose / H.D.Connector as directed.

Note:- Maximum up to 6 mtrs length, excess will be considered

as Mains for Secondary Point.

163 (a) with medium class Rigid PVC pipe and accessories Pt. 131

2 Point wiring for Light / Bell with 2-1.5 sq.mm &earthwire of

1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multistrand copper wires, in following type of

pipe to be erected concealed in/ on surface on wall/ceiling

complete with 6A Modular type switch / bell push &

accessories and earth continuity of following type, erected on

PVC / Metallic box, single mounting base frame covered with

textured/metallic front plate modules erected on / in wall /

ceiling as per pipe erected, with necessary Lamp holder/ceiling

rose / H.D.Connector as directed. 0

(a) with medium class Rigid PVC pipe and accessories erected

flushed on wall/ceiling complete 0

162 Cat. III Pt. 372

3 Point wiring for FAN with 2-1.5 sq.mm &earthwire of

sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS

PVC insulated multistrand copper wires, in following type of

pipe to be erected concealed in / flushed on wall/ceiling

complete with 6A Modular type switch and hum free EME four

or more step type electronic fan regulator with separately

mounted and accessories with earth continuity of following

type erected on PVC / Metallic box, single mounting base

frame covered with textured/metallic front plate modules

erected on / in wall / ceiling as per pipe erected. with necessary

ceiling rose / H.D.Connector as directed. 0

(a) with medium class Rigid PVC pipe and accessories erected

flushed on wall/ceiling complete 0

60 Cat. III Pt. 632

4 Point wiring for Individual Plug with &earthwire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multistrand copper wires, in following type of to be

erected concealed in / on surface of wall / ceiling complete with

Modular type switch & 5 pin Plug erected on PVC / Metallic

box covered with appropriate front plate modules erected on /

in wall / ceiling as per pipe erected with following type of

[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire

from nearby switchboard/mcbdb board 0

(a) with medium class Rigid PVC pipe and accessories erected

flushed on wall/ceiling complete 0

70 Cat. III Pt. 471

5 Point wiring for Looped Plug with 6A Modular type switch &

pin socket erected on PVC / Metallic box, single mounting base

frame covered with textured / metallic front plate modules

erected on / in wall / ceiling with following type accessories 0

79 Cat. III Pt. 255

6 Providing following type of Modular Type Accessories

mounted with pvc / metallic box, single mounting base frame

covered with textured / metallic front plate , modules erected

with necessary connection. As desired by Engineer In charge 0

(9) 16 Amp. SP one way switch 0

43 Cat.III Ea. 179

(10) 6/16Amp. Universal socket 0

43 Cat.III Ea. 198

Section :- 1- 3 / Conduits & Pipes 0

7 Providing and erecting ISI mark Medium class RIGID PVC

PIPES of following size complete to be erected on/in wall or

ceiling erected with necessary PVC fittings & Junction boxes

fixed with adhesive solution & Clamps with following dia of

pipes, in approved manner as directed 0

25 (a) 20 mm Mtr. 33

8 Providing & erecting PVC Corrugated Flexible Conduit with

required nos. of coupling, PVC bushes, Check-nuts etc.

complete of following sizes. 0

Section 1-4 Mains & Wires 0

9 Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm

copper conductor FRLS PVC insulated stranded wire of green

colour for earth continuity of following size 0

(a) with medium class Rigid PVC pipe and accessories 0

1500 (b) 2 wire 2.5 sq. mm (From LDB to SB and SB) Mtr. 82

10 Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm copper conductor

FRLS PVC insulated stranded wire of green colour for earth

continuity of following size 0

. (a) with medium class Rigid PVC pipe and accessories 0

1000 (a) 2 wire 4 sqmm Mtr. 111

11 Providing & Erecting approved make following size of TV Co-

axial flexible cable comprising inner conductor of solid bare

copper insulated with Foam PE & Secondary conductor made

of poly - Aluminium film bonded Al. Braids @ suitable

coverage overall sheathed with black PVC insulation. 0

50 (c) RG - 6 CCS Mtr. 21

12 Supplying & erecting approved make Telephone Cable

electrolytic copper conductor PE insulation twisted in two

pairs, & wrapped with FRLS PVC tape & sheathed with

FRLS PVC or HFFR outer Jacket suitable for telephone wiring

& confirming to C-DOT erected in existing pipe. of following

size of conductors &nos.of pairs. With necessary connections. 0

[A] Conductor Size 0.5 mm 0

(a) Unarmoured 0

75 (2) Two Pairs Mtr. 20

LED LUMINARIES 0

Indoor LED Fittings 0

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick sheet

Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with

diffuser with company mark/name 160V to 270V, Power

Factor more than 0.95, THD <15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick sheet

Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with

diffuser with company mark/name 160V to 270V, Power

Factor more than 0.95, THD <15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)

12 (i) 5-10 Watts, Surge-2 KV, IP-20, conventional 1 to 2 feet

28 Cat-lll Ea 164

(iii) 18-20 Watts, Surge - 2KV,IP-20, conventional 4 feet

42 Cat-lll Ea 293

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick sheet

Steel conforming to IS: 513/CRCA/aluminium pressure die cast

powder coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with company

160V to 270V,Power Factor more than 0.95, THD <15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick sheet

Steel conforming to IS: 513/CRCA/aluminium pressure die cast

powder coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with company

160V to 270V,Power Factor more than 0.95, THD <15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount

Downlight with provision for spring loaded mounting clips

(i) 5-9 watts,Surge-2 KV

82 Cat-lll Ea 218

(ii) 11-15 watts, Surge-2 KV

14 Cat-lll Ea 423

(iii) 16-20 watts, Surge-2 KV

110 Cat-lll Ea 584

13 Supplying and erecting LED street light / Flood light fittings

with High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast aluminum housing

with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95, THD <

10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver efficiency >

85 %.( fittings required LM-79 & LM-80 certificates)(NOTE:

Below description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.)

(C) Post Top Lantern LED fitting comprises of finish cast

aluminum spigot and spun aluminum canopy fixed with opal

polycarbonate, pipe arrangement for vertical mounting driver

and accessories wired upto terminal block.IP

25 Cat-lll Ea 4052

(G) Step Light having Aluminium die cast and ABS Plastic

(i) 5 watts, Direct/Indirect luminaire

6-1 STREET LIGHTPOLES

Indoor LED Fittings

14 Supplying & erecting Galvanized M.S pipe post “B” class

mm O.D 4 mtr. Long duly painted with two coats of

aluminium paint complete with metallic base plate of 300 mm x

300 mm x 4mm thick for using as a compound light pole with

approx. weight 32 Kg.

15 Supplying &erecting approved make SMC press moulded

composite FRP. loop-in, loop-out approx. 2mm thick box

complete with Bakelite connector strip 5way(3P+N+E),DIN

rail for mounting mob & hinged doors as per requirement

having locking arrangements with mounting clamp with nuts,

bolts & washers suitable for erection on pole with cable

clamps& earth bolt of following size of box.

25 (B) 250mm x 200mm x 100mm [deep] Ea. 510

16 Providing 1:2:4 cement concrete foundation & 70 % PCC from

bottom including excavation for the pole of size 45 x 45 x

cm. Deep in below ground level with plinth of 45 cm x 45 cm

(or 45 cm dia x 45 cm) high upper ground level with necessary

curing and finishing in approved manner.

( for 4 & 6 mtr pole)

SWITCHGEARS & DISTRIBUTION BOARDS 0

Section 3-4 MOULDED CASE CIRCUIT BREAKERS 0

14 Providing and erecting Approved make Four pole moulded case

circuit breaker having breaking capacity ICU of 25 KA. at

V,having normal current rating up to 25 A to 100A. with Fixed

thermal & magnetic release suitable to work on A.C. supply

c/s. with all internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing. 0

6 ICS=100% of ICU only Cat III Ea. 6112

17 Providing and erecting Approved make Four pole moulded

case circuit breaker having breaking capacity ICU of 35 KA. at

415 V. having Normal current rating 200A.with variable

Thermal & magnetic release suitable to work on A.C.supply

c/s. with all internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S.housing 0

2 ICS=100% of ICU only Cat III Ea. 16061

Section 3-8 / PANEL MOUNTING BUSBARS 0

18 Supplying and erecting triple pole & neutral 440V / 500V panel

mounting Copper Busbars with four equal Nos. of electrolyte

bus having current density not more than 1.6 Amp. / sq.mm

(Rated current / cross section area) duly wrapped with colour

insulating tape for phase sequence of following current carrying

capacity, erected with necessary bus bar supports /insulators,

main cable socket to each bar, erected in existing cubical panel

with necessary connections. 0

14 (B) Suitable for 200 Amp. capacity Rn.Mtr 3171

12 (C) Suitable for 300 Amp. capacity Rn.Mtr 4861

SECTION 3-10 / MINIATURE CIRCUIT BREAKERS 0

19 providing and erecting Miniature circuit breaker single pole 6A

to 25A suitable to operate on 240 V A.C. system and having

breaking capacity 10 KA to be erected in existing box.

confirming to IS 8828/1996 with ISI Mark 0

110 Cat.III Ea. 111

20 Providing & erecting 240 V MCB double pole switch for motor

& inductive load (C Curve) having 10 KA breaking capacity

& confirms to IS : 8828 in existing box having following

21 Providing & erecting 415 V MCB Four Pole for Motor &

Inductive Load (C Curve) having 10KA breaking capacity &

confirms to IS :8828 in existing box having following capacity 0

8 Cat III Ea. 662

12 Cat iii Ea. 730

22 Providing & erecting 415 V MCB three Pole for Motor &

Inductive Load (C Curve) having 10KA breaking capacity &

confirms to IS :8828 in existing box having following capacity 0

(a) 6 to 32 Amp. 0

23 Supplying & erecting 20 Amp 10 KA ‘C Curve’ single

pole MCB with 20 Amp. Plug socket, company fabricated

powder coated sheet steel enclosure erected as directed with

[A] Metal Clad Socket with metal clad top 0

1 Cat.III Ea. 582

SECTION 3-11 MCB DISTRIBUTION BOARDS 0

24 5 Half / One Module Blanking Plate of Standard Size. Ea. 35

25 Supplying & erecting approved make RCCB + MCB (Electro

magnetic type only) working on residual current device having

10 KA short circuit breaking capacity and 30 mAmp.

Sensitivity & 30 mili sec. tripping time conforming to IS

test knob facility trip free mechanism operating for rated

leakage at nominal ten volt, complete erected including all

materials lugs screws etc. completed.

[e] 32A to 40 A, 4 Pole Three Phase

2 Cat. II Ea. 2145

[f] 63A, 4 pole Three Phase

6 Cat. II Ea. 2806

SECTION 3-14 EARTHING 0

26 Providing and erecting required size HOT deep Galvanised iron

strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel

20 board, Motors etc. using proper clamp. (25x3MM) Kg. 77

27 Providing and erecting Annealed bare Copper wire 8 to

28 Supplying & erecting in earthpit of minimum bore dia. 225mm

size ASH or approved make Safe Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free G.I.Pipes having Outer pipe dia of

mm having 80-200 Micron galvanising, Inner pipe dia of

mm having 200-250 Micron galvanising, connection terminal

dia of 14 mm with constant ohmic value surrounded by

highly conductive compound with high charge dissipation

suitable for following type of applications. 0

[C] For Electrical Installation covering Transformer Neutrals,

Lightning arrester Earthing, A.C.Plant& Sensitive

Computer System(like Automation, SCADA)i.e.

independent Earthing located in other than normal soil i.e.

Soft Rock, Marshy Soil etc..

-Length of Pipe : 3 Mtrs.

8 -Back filling Compound :2 nos Bags of 25 Kg. Ea. 10489

SECTION 3-16 CUPBOARDS. 0

29 Providing & erecting weather proof, dust & vermin proof, floor

mounted front operated indoor type cubical panel board

necessary IP-42 and above protection as per approval from

engineer incharge made from 14 SWG thick CRC M.S. sheet

for outer body & doors, 16 SWG thick CRC M.S.sheet for

internal partitions with necessary accesories , supporting

angles/ flats channel including cutting, bending, drilling,

welding, riveting with internal partitions & cable alley as per

requirements & instruction of engineer-in-charge with erection

supplied switch gears, BUSBARS, suitable size of inter

connecting PVC copper wire / copper-aluminium strips, rubber

grommets, rib, bakelite control fuses/MCB for measuring

instruments, earth bus & earth bolts, foundation flange - bolts-

base Plates, sufficient nos. of hinged doors, handles with

locking arrangement and rubber gasket,heavy duty end terminal

connection,danger notice board,necessaryventilation,earthing

strip complete. The Panel shall be painted with epoxy powder

(The rates excludes the cost of switchgears, bus bars, inter

connecting mains & Copper Aluminiumstrips, meters, Fuses

etc. The dimension shall be measured excluding base beams)

The panel shall be supplied with following approved

manufacturers with following size.

(A) locally fabricated panel board 0

45 (i) with 350 mm depth Sq.Mtr 10365

SECTION 4-3 / ARMOURED ALUMINIUM CABLES 0

30 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be laid

on wall with necessary clamps or in existing trench / pipe of

following size of cables (VERIFY THE ACTUAL LENGTH

6 (A) 3 1/2 core 25 Sq. mm ( 16 Sq. mm 1/2 core) Mtr. 182

SECTION 4-4 / ARMOURED COPPER CABLES

31 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Copper conductor for 1.1 KV. to be laid on

wall with necessary clamps or in existing trench / pipe at road

crossing or floor of following size of cable.

60 (A) 4 core 2.5 Sq. mm Mtr. 269

50 (B) 4 core 6 Sq. mm Mtr. 505

32 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Copper conductor for 1.1 KV. to be laid

on wall with necessary clamps or in existing trench / pipe at

road crossing or floor of following size of cables.

160 (A) 4 core 10 Sq. mm Mtr. 269

SECTION 4-5 MISCELLANEOUS.

33 Making trench in soft soil of suitable width of 90 cm deep for

laying cable or locating the fault all over the run and back

300 filling the same and making the surface as normal ground. mtr 55

34 Covering of cable with second class bricks or cement tiles laid

cover the cable crosswise & also on both sides with covering of

7. 5 Cm. layer of sand above & below cable (16 bricks per

375 meter) mtr 139

SECTION 4-6 / CABLE GLANDS.

35 Providing and, fixing heavy duty flange type brass cable gland

with rubber ring for PVC insulated armoured cable complete

with out going tails, insulating tape etc for following size of

16 (\B) 2 to 4 core 2.5 / 6 Sq. mm Ea. 38

52 (C) 2 to 4 core 10 Sq. mm Ea. 38

36 Providing and, fixing heavy duty flange type brass cable gland

with rubber ring for PVC insulated armoured cable complete

with out going tails, insulating tape etc for following size of

SECTION 4-7 CABLE LUGS.

37 Solderless crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner.

38 Solder less crimping type Copper lugs conforming to IS

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner.

CHAPTER - V Fans and Accessories

SECTION 5-1 / CEILING FANS AND ACCESSORIES

39 Providing & erecting Approved make Ceiling Fan with double

ball bearing ISI mark with Condenser 230 volt A.C.50 Hz

1200 mm sweep complete having 3 blades aluminium body and

blade sets having ornamental design shanks , canopy erected

with earthing. [ Make shall be approved by Engineer in

60 Charge] Ea. 2289

SECTION 5-2 FAN ACCESSORIES

40 Supplying and erecting 19 / 20 mm. nominal bore Medium

Class M.S. Pipe down rod erected duly painted for fan

60 complete with proper insulation without leakage and earthing. Mtr 107

41 Supplying & erecting Fan Hook of 10 mm M.S. Round bar

60 grouted in RCC slab with Making the site as original. Ea. 43

SECTION 6-7 TIME SWITCHES

42 Supplying & erecting approved make time switch with single

pole air break contacts suitable for 230 V.15/16A.complete

with self starting motor driven clock ‘ON’ &’ OFF’ automatic

arrangement at any predetermined time during each

hours,With nickel cadmium rechargeable battery backup

3 erected as directed. Ea. 2331

43 Supplying & erecting power contactor ,AC3 duty for time

switch complete erected as per direction Cat III

3 (D) 4 pole 440V 40 Amp. Ea. 2755

LIGHTNING ARRESTER

44 SITC of Vertical Air Termination Solid aluminium with Base-

10 mm dia and 1000 mm long. Air Termination Base tested for

conditioning, Ageing Test & Lightning impulse current

withstand test: 100 kA of 10/350µs waveform in an accredited

Third party laboratory as per 6.3 & 6.4 of IEC 62561-1

protocol with MAST 34mm dia 3000 mm long- Cold

2 Galvanized Each 11000

45 SITC of Galvanized Steel Flat 25x6 mm thickness from earth

electrode directly in ground as required. Zinc coating: 500 g/m

square (Approx:70 micron coating) tested and used exclusively

for lightning protection earthing system and ring equipotential

200 bonding. Mtr 153

MARKET RATE ITEMS:-

SUB PANEL & DISTRIBUTION BOARDS

46 Supply, installing, testing and commissioning of metallic

double door type distribution board with following MCBs /

ELMCBs / RCCBs / etc. with all necessary connections,

remaining blank area shall be covered with blanking (dummy)

plates etc. complete. (All DBs shall be installed concealed in

Non-Plant Bldg.) w.r.t Technical specification

Note All MCBs & MCCBs taken in SOR

47 4-WAY VTPN DB :

Incoming : 40 A FP RCBo-30mA

Outgoing : 6 to 32 A SP MCB (12 nos) (MCB TAKEN IN

2 ABOVE SOR) Ea. 12000

4-WAY VTPN DB :

Incoming : 63 A FP RCBo-30mA

Outgoing : 6 to 32 A SP MCB (12 nos) (MCB TAKEN IN

4 ABOVE SOR) Ea. 12000

4-WAY VTPN DB :

Incoming : 63 A FP MCB

Outgoing : 6 to 32 A SP MCB (12 nos) (MCB TAKEN IN

3 ABOVE SOR) Ea. 12000

6-WAY VTPN DB :

Incoming : 63 A FP RCBo-30mA

Outgoing : 6 to 32 A SP MCB (18nos) (MCB TAKEN IN

2 ABOVE SOR) Ea. 13500

6-WAY VTPN DB :

Incoming : 80 A FP MCB

Outgoing : 6 to 32 A SP MCB (18nos) (MCB TAKEN IN

1 ABOVE SOR) Ea. 13500

8 -WAY VTPN DB :

Incoming : 100 A FP MCCB

Outgoing : 6 to 32 A SP MCB (24 nos) (MCB TAKEN IN

1 ABOVE SOR) Ea. 15000

Incoming : 160 A FP MCCB

Outgoing : 63 A FP MCB (1 nos) (MCB TAKEN IN

Outgoing : 100 A FP MCB (1 nos) (MCB TAKEN IN

SUB PANEL SF PANEL 1 (BANQUET HALL 1)

Incoming : 160 A FP MCCB

Outgoing : 63 A FP MCB (1 nos) (MCB TAKEN IN

Outgoing : 100 A FP MCB (1 nos) (MCB TAKEN IN

SUB PANEL SF PANEL2 (BANQUET HALL 2)

Incoming : 80 A FP MCCB

Outgoing : 63 A FP MCB (1 nos) (MCB TAKEN IN

Outgoing : 40 A FP MCB (1 nos) (MCB TAKEN IN

SUB PANEL TF PANEL1 (GYMNASIUM)

Incoming : 80 A FP MCCB

Outgoing : 40 A FP MCB (2 nos) (MCB TAKEN IN

SUB PANEL TF PANEL2 (RESTAURANT)

Incoming : 80 A FP MCCB

Outgoing : 63 A FP MCB (1 nos) (MCB TAKEN IN

Outgoing : 40 A FP MCB (2 nos) (MCB TAKEN IN

48 Supply, installation, testing and commissioning of OUTDOOR

water tight fitting wall washer suitable for wall mounting with

29 12 W LED lamp complete Ea 900

49 Supply and Installation of High Volume Low Speed Fan

(HVLS) 12 feet Dia., 5 blades complete. With Motor, Control

2 Panel, Controller, Mounting arrangements etc. Ea 192500

50 Supply and Installation of High Volume Low Speed Fan

(HVLS) 10 feet Dia., 5 blades complete. With Motor, Control

4 Panel, Controller, Mounting arrangements etc. Ea 172500

PART-D ( FIRE FIGHTING ITEMS)

A FIRE HYDRANT SYSTEM

Providing, laying, jointing, testing and

commissioning of following sizes of pipes

conforming to IS-1239 and IS:3589, with all

accessories like all fittings (standard M.S.

fitting with welded joint shall be used on the

pipes) including tees, elbows, reducers, union,

flanges, rubber gaskets, GI nuts bolts,

washer including supporting/fixing the pipe

1.00 on floor / wall /ceiling with clamps, hangers

(using anchor fastners) as per specification.

All hangers, clamps, brackets etc. shall be of

galvanized iron unless specified otherwire and

then supply of the same shall also be included

for rates under this head.. Welding of any

kind on the galvanized support / hanger shall

not be permitted. Arc Welding procedure as

For wet riser System - M.S `C' Heavy class

pipe (For Hydrant ,)

Providing & fixing of Single Fire Hydrant

Valve, Single Outlet, SS-304, 63 mm female

inst. oblique type, 80 mm NB flange Inlet.,

200 mm OD, 160 mm PCD, 4 holes of

1.1 4 mm, complete with C.I wheel, PVC Blank Nos.

Cap and G.I Chain, Bearing IS:5290 mark,

Painted red. Including fixing with anchor

fastner and flanged tapping from wet riser

complete as required.

SITC of Air Release Valve For Fire Hydrant

Riser, 25 mm Male BSP

Threaded, GM, Nitrile Rubber Ball And

Sheet, Minimum 1,556.00

Operating Pressure 2 Kg/Cm2 with all

Providing & fixing swinging type ISI mark,

First Aid hose reel in red colour drum with

mts long and 20 mm dia heavy duty rubber

braided water hose , terminating with SS

coupling & nozzle of 6mm outlet with shut

1.3 4 off valve confirming to IS 8090 - 1976 Nos

complete with MS socket for tap-off, drum

and brackets (including painting) for fixing on

wall with anchor fastner, bolts & nuts

conforming to IS:884-1969 complete as

Providing and Fixing of Branchpipe,

short, Stainless Steel, 63mm male inst. inlet,

Fitted with male threaded outlet,20 mm bore

1.4 4 nozzle, Nos.

bearing IS:903 mark, suitable for inter

connection to hose pipe coupling

complete as required.

Providing and fixing Hose Box lockable

cabinet, made out of MS sheet of 16 gauge

thickness having central opening and 4 mm

thick glazed glass doors (Two nos.) suitably

marked on the outside with the letters "FIRE

HOSE" including necessary locking 1,905.00

arrangement and shall be painted with one

coat of primer and two coats of synthetic

enamel paint of approved shade.(External)

Size: 750 mm x 600 mm x 250 mm.

Providing & fixing of fire brigade connection

made from SS 304 (suction collecting head)

consisting of 4 Nos. 63 mm dia instantaneous

type male couplings with built-in check

1.60 1 valves, drain valve 1 No. 150 mm dia Nos.

butterfly valve, 150 mm dia. non return valve

with flanged outlet complete with bolts, nuts

and rubber insertions as required and as per

B SPRINKLER SYSTEM

Providing, laying, jointing, testing and

commissioning of following sizes of pipes

conforming to IS-1239 and IS:3589, with all

accessories like all fittings (standard M.S.

fitting with welded joint shall be used on the

pipes) including tees, elbows, reducers, union,

flanges, rubber gaskets, GI nuts bolts,

washer including supporting/fixing the pipe

2.0 on floor / wall /ceiling with clamps, hangers

(using anchor fastners) as per specification.

All hangers, clamps, brackets etc. shall be of

galvanized iron unless specified otherwire and

then supply of the same shall also be included

for rates under this head.. Welding of any

kind on the galvanized support / hanger shall

not be permitted. Arc Welding procedure as

For Sprinkler System - M.S `C' Heavy class

Supply Installation testing &comissioning of

UL / FM approved pendent / Upright type,

2.10 256 chrome plated / Brass finished sprinkler, Inlet Nos.

15 NB, 68 deg.with heat activated, Quick

Response type, K-115, with required

Providing and fixing of UL listed and FM

approved flexible hose

drop with required accessories and false 1,455.00

ceilling clamps.

Supply, installation, testing and

commissioning of vertical sprinkler Alarm

Valve With Motor Gong with all required

accessories like in built drain valve, test valve, -

gauge cock and pressure gauges etc. Sprinkler

alarm valve shall be FM approved.

Providing and fixing of inspector test and

drain assembly PN 16 with sight glasss, ball

valve, union, nipple etc. Test drain assembly 2,250.00

shall be comlete in all respect.

Providing and fixing of flange ended Y

strainer PN 16 with SS scrin of

mesh/sq.inch. Flange drilling standard shall be -

Providing and Fixing of hand lever operated

butter fly valve, PN: 1.6, with CI body and

S.G disc and other working parts as per IS:

13095 - 1991. With required accessories like -

matching flange, packings etc. complete as

a 0 50 mm dia Nos.

b 4 80 mm dia Nos.

c 2 100 mm dia Nos.

SITC electrically operated water flow

switches (Vane type) including tamper switch

and accessories, complete with tap off socket

arrangement as required, with potential free

contact with 2 Nos. NONC suitable to be 875.00

fixed directly on line of the foll. diameter of

pipes including cabling till alarm panel and all

other accessories to finish the installation.

Providing and fixing of Glycrinfeeledburdon

type pressure guage, made from SS working

parts and SS casing, 150 mm dial and 0-21 kg

range with calibration certificate and Shall be 810.00

fitted with shut off valve and SS 304 syphon

tube and other required accessories.

SITC of 25mm dia Air Vent Valves with

2.90 3 mm dia. Ball valve and other required Nos.

accessories like nipple, socket etc.

SITC of pressure release valve with ball valve

and accessories 3,600.00

Providing and fixing of MS support with

required anchor fasteners, insert plate etc.

2.11 1000 with one coat of zinch chromate and two caot Kg

of black enemal paint. Support shall be

complete in all respect.

C PUMP HOUSE EQUIPMENTS

Supply, installation, testing and

commissioning of electrically driven high

3.00 1 pressure centrifugal fire hydrant & Sprinkler Set

pump suitable for automatic operation

consisting of the following:

Horizontal end suction / high pressure

centrifugal pump, suitable for operation on

415 volts ± 6%, 3 phase, 50 HZ A.C supply.

The installation shall be complete with

flexible coupling and coupling guard as

required. Fire pump shall have C.I. casing,

CS diffusers, bronze impeller (hard finished

and dynamically balanced) and S.S. (304)

Shaft with mechanical seal, capable for

delivering 2280 LPM at outlet head of 70 -

MWC to ensure a minimum pressure of

Kg/Sqcm at the farthest or topmost hydrant.

The installation shall be complete with

necessary pressure gauge with gun metal shut

off cock on delivery side. (The pump should

be tested for bench mark at factory and shall

be gotten approved by the Local fire

Pump shall be capable of furnishing not less

than 150% of rated capacity at a head of not

less than 65% of the rated head. The shut off -

head shall not exceed 120% of rated head.

b. Squirrel cage induction motor, TEFC type

suitable for operation on 415 volts, 3 phase

50 HZ A.C supply, for the above pump with

synchronous speed of 2900 RPM, conforming

to IP 55 protection & class F insulation. The -

motor shall conform to IS 325-1978 (up to

date) with flexible coupling and coupling

guard, complete as required.

Common base plate for (a) and (b) from

M.S. Channel for required size. -

Suitable cement concrete foundation with

cement concrete plaster (design and drawing

to be provided by the Contractor while the

foundation will be done by others) complete -

with anti-vibration arrangement of cushy foot

Supply, installation, testing and

commissioning of Diesel Engine driven fire

3.10 1 pump suitable for automatic operation Set

comprising of the following and conforming

to BS 649/IS 10002 all amended upto date.

Horizontal, End section, Back pullout

centrifugal pump, suitable for operation on

415 volts ± 6%, 3 phase, 50 HZ A.C supply.

The installation shall be complete with

flexible coupling and coupling guard as

required. Fire pump shall have C.I. casing,

CS diffusers, bronze impeller (hard

a finished and dynamically balanced) and

CS shaft with mechanical seal, capable for

delivering 2280 LPM at outlet head of

MWCminimum pressure of 3.5 Kg/Sqcm at

the farthest or topmost hydrant / sprinkler.

The installation shall be complete with

necessary pressure gauge with gun metal shut

off cock on delivery side.

Pump shall be capable of furnishing not less

than 150% of rated capacity at a head of not

less than 65% of the rated head. The shut off -

head shall not exceed 120% of rated head.

Heat exchanger cooled (secondary cooling)

diesel engine of speed 1800 RPM suitable for

the above pump with automatic starting

mechanism and other accessories including

fuel tank (fabricated from 3mm MS sheet,

painted with two coats of synthetic enamel

paint over a coat of primer) of capacity

adequate to sustain pump operation for

c hours continuous working. The tank shall be

fitted with Magnetic oil level indicator, MH

with cover, drain valve, air vent including

structural supports (painted with approved

shade), 1 Nos. x 12 volt battery, heat

exchanger with necessary piping connections

& fittings, flexible coupling, coupling guard

& exhaust pipe connection complete as

Diseal engine tank 200 ltr capacity minimum. -

Common base plate for (a) and (b) from

e M.S. channel of required size. -

Including Diesel Engine control panel with

Battery charger. -

Suitable cement concrete foundation with

plaster, (design and drawing to be provided by

g the Contractor while the foundation will be

done by others) complete with antivibration

arrangement of cushy foot mountings.

Supply, installation, testing and

commissioning of jockey pump

(pressurisation pump) comprising of the 2,01,000.00

Horizontal end suction centrifugal pump of

180 LPM with 70 Head, suitable for operation

on 415 volts ± 6%, 3 phase, 50 HZ A.C

The installation shall be complete with

Flexible coupling and coupling guard,

complete as required.

The pump casing shall be CI, shaft shall be SS

& impeller / shaft sleeve / casing wearing ring

shall be bronze. The pump shall be provided

with mechanical seal The system shall be

complete with necessary pressure gauge with -

gun metal shut off cock on delivery side. (The

pump should meet the condition and shall be

gotten approved by the Local fire Authority).

Squirrel cage induction motor TEFC type for

operation on 415 V, 3 phase 50 HZ AC

supply for the above pump with a

synchronous speed of 2900 R.P.M. with -

flexible coupling and coupling guard etc. as

Common base plate for (a) and (b) from

M.S. channel as required size. -

Suitable cement concrete foundation with

plaster, (design and drawing to be provided by

e the Contractor while the foundation will be

done by others) complete with Antivibration

arrangement of cushy foot mounting.

Providing & fixing pressure switch assembly

with isolation valve suitable for working

pressure of 10 bar. Cost shall be inclusive of

providing any short pieces, nipples, elbows

etc as required.

General specification of pressure switch

Encloser : Painted Mild Steel to IP:33 as per

IS:13947 (Part-1)

Sensing Element Phosphor Bronze Bellows 3,700.00

Switching : 1 SPDT Contact System

Switch Rating : 6A Inductive / 10A Resistive

240V AC, 0.2A Inductive

Repeatability / Accuracy : ± 2% FSR

Process Connection 1/4" BSP (F)

Cable Entry : Suitable for 6 to 14 mm dia

Supplying, installing, testing and

commissioning of C.I. Non-return valves as

3.40 per IS:5312 (Part I) 1984, swing check type

with required flanges, nuts, bolts and gaskets

etc. complete. (PN 16 Rated.)

a 2 150 mm dia Nos.

b 1 100 mm dia Nos.

Providing & fixing of flange ended rubber

expansion bellow joint of standard length as

3.50 per manufacturers specs including rubber

gaskets, flanges, nuts, bolts and washers

complete as required. (PN 16 Rated.)

a 8 150 mm dia Nos.

Supplying, installing and commissioning of

CO2 4.5 Kg Fire Extinguisher containing

99.95% Co2 Gas, fitted with discharge hose,

wall mounting bracket etc., ISI approved as 3,900.00

per IS:15683:2006 complete with Required

size of Zebra paintaing on wall and floor.

Supplying, installing and commissioning of

ABC 6 Kg Fire Extinguisher containing MAP

50, Stored Pressure Type, fitted with Pressure

Gauge, fitted with discharge hose, wall

mounting bracket etc., applicable on Class A, 1,450.00

B,C ISI approved as per IS:15683:2006

complete with Required size of Zebra

paintaing on wall and floor.

PART -E (HVAC ITEMS)

Appendix-1- (VRF AC System with Standard VRF Units )

1 Section 1: High Side Work

Supply & Installation of Outdoor condensing

units of the following capacity with R

Gas Based Model. (Bidder to offer nearest

size of Unit & suitable combinations available

with them & must consider piping derating for

Up to 40 KWr capacity Min EER 3.28 and

40 to 70 KWr capacity Min EER 3.26 and

Above 70 KWr capacity Min EER 3.02 and

First Floor : CKT 01 - 32 HP ( 16 HP + 16 HP

)- - Top Discharge

Second Floor : CKT 01 - 20 HP ( 20 HP )- -

Second Floor : CKT 02 - 12 HP - Side

Second Floor : CKT 03 - 10 HP - Side

Third Floor : CKT 01 - 10 HP - Side

Third Floor : CKT 02 - 12 HP - Side

Supply & Installation of VRF-indoor units of

1.02 the following capacity. (Bidder to offer

nearest size of Unit available with them)

Ceiling mounted 4 way Compact Cassette

Unit with condensate drain pump

Ceiling mounted 4 way Cassette Unit with

condensate drain pump.

1.03 Remote control Systems

Cordless remote controllers ( Operating

Mode:- On/Off/Fan Speed/Mode/Temp )

Ref-net joints for above VRF systems.

1.05 1 Outdoor unit branch kit Nos. 5000

2 Section 2: Low Side Work

Epoxy painted M.S. structure for supports and

For VRF system, all refrigerant piping

between indoor & outdoor units duly insulated

as per specifications. All piping inside the

room shall be properly supported with hanger

and exposed piping shall be properly

2.02 supported in GI Perforated tray. Exposed

piping insulation to be covered with 1 layer

of glass cloth and 2 layers of UV paint and

all the insulation joints must be covered

with EPDM Rubber Tape. (minimum

mm thick Class O Insulation)

2.02.01 For Folloing HP Ref Piping

2.02.01.02 50 20 HP VRF Piping CKT

2.02.01.03 100 32 HP VRF Piping CKT

Supply & Installation of Insulated uPVC drain

piping for all VRF Indoor AC units. (All the

Insulation joint must be covered with

aerotape.) ( min 9 mm thick)

Testing & Commissioning of VRF system

along with topping-up of refrigerant Gas.

2.04.01 4 10 / 12 HP VRF CKT Nos

2.04.02 1 20 HP VRF Piping CKT Nos

2.04.03 1 32 HP VRF Piping CKT Nos

2.05 Electrcial Work:-

All Cu armored power cable between

electrical panel & VRF ODU’s located on

2.05.01 Terrace. This cabling should be properly

supported in G.I Cable trays where-ever

2.05.01.01 0 06 Sq mm X 4 Core Copper Rmt

2.05.01.02 0 10 Sq mm X 4 Core Copper Rmt

2.05.01.03 0 16 Sq mm X 4 Core Copper Rmt

10 Sq mm Cu Single core wire for earthing

All control cables between indoor and

2.05.03 outdoor unit lay in PVC pipe and clamped.(for

2.05.03.01 600 1.5 Sq.mm 2 core Shielded Control Cable Rmt

1.6 mm thk G.I perforated cable trays with

2.06 necessary structural supports, anchor bolts,

etc. for the above work.

90 Deg ODU Exhaust Air Cowl with 18 G GI

& MS Frame Work & Safety Chicken Mess

Appendix-2- (LVL 0 Room Split AC )

1 Section 1: High Side Work

SITC of DX air-cooled Split AC unit

complete with Indoor / Outdoor units along

with cordless remote controller &aditional

charge of refrigerant. (R-410a / R32

Refrigerant)(Min. 3 Star & Cu Cond.)

1.01 (Without Ref Piping )

2 Section 2: Low Side Work

Supply, Fabrication and Erecting structure

steel for support. Applying two coats of zinc

chromate primer of ICI, Asain make/eq. , with

rubber gasket between support & duct / pipe

2.01 as per specifications and drawings and as

directed by the Engineer-in-Charge client

/consultant. Make : Tata / Sail / JSW as per

IS-2062 with TC. ( with 2 coats of approved

0 color epoxy paint ) Kg 0

For AC system, all refrigerant piping between

IDU & outdoor units duly insulated as per

specifications. All piping inside the room shall

be properly supported with hanger and

exposed piping shall be properly supported

with clamp.Exposed piping insulation to be

covered with 1 layer of glass cloth and

layers of UV paint and all the insulation joints

must be covered with EPDM Rubber Tape.

For 1.0 / 1.5 TR ( Min 1/4" (0.8mm thk) &

2.02.01 6 1/2" (0.8mm thk) with min 13 mm Rmt

thkIsulation) 1000

Supply & Installation of Insulated uPVC drain

piping for all Indoor AC units. (All the

Insulation joint must be covered with

2.03.01 6 For 19/25 mm dia piping Rmt

All Cu armored power cable / control cable

between IDU to ODU’s .

2.04.01 8 4 Core x 2.5 Sqmm Copper armored) Rmt

2.04.02 0 6 Core x 2.5 Sqmm Copper armored) Rmt

2.05 1 L type Wall Mounted Powder coated GI Satnd Nos 1000

Signage Sticker for each OUD with Room

Name (for Identification) 400

2.06 2 Chipping Work in Wall Rmt 150

AHMEDABAD MUNICIPAL CORPORATION

ENGINEERING DEPARTMENT- BUILDING PROJECT

CONSTRUCTION OF COMMUNITY BUILDING AT T. P. S. No. 5 (City Wall Improvement)

(Section – 7) Final Sanc., F. P. No. 26, At: Dariyapur - Kazipur, Taluka: City, District:

Ahmedabad, near dariyapurgatedariyapur ward central zone, Ahmedabad

FINANCIAL BID (Online Only)

RECAPULATION SHEET

SR.NO. DESCRIPTION AMOUNT

1 EARTH WORKS & ALLIED WORKS

2 CONCRETE & ALLIED WORK

3 STRUCTURAL STEEL & ALLIED WORKS

4 ROOFING & ALLIED WORKS

5 MASONARY AND PLASTER WORK

12 AS PER MARKET RATE

13 TOTAL ELCRTICAL WORK

14 VRF AC SYSTEM WITH STANDARD VRF UNITS AND SPLIT AC

15 A. FIRE HYDRANT SYSTEM

16 B. SPRINKLER SYSTEM

17 C.PUMP HOUSE EQUIPMENT

18 Heritage Impact Assessment (HIA)

I/We am/are willing to carry out work at ______% above / below (should be written in figures and

the estimated cost mentioned above.

Estimated cost put to tender :Rs.00000 Estimated cost put to tender :Rs.000000

Add_____% above : Rs ___________ Deduct_____% below : Rs __________

In words : Rupees

Signature of contractor Additional City Engineer (Central Zone )

Seal Ahmedabad Municipal Corporation