Routine Maintenance of Buildings of Kargil district (All Sub Divisions/Blocks of Kargil District ) Under Maintenance and Repair work for the year 2026-27

Earth work in excavation by manual means in foundation trenches or drains (not exceeding 1.5 m in width or IO sqm on plan), including dressing Of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

A) All kinds of soil

B) Soft Rock

C) Hard Rock

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : in 1:6 cement mortar

Random rubble masonry with hard stone laid dry in foundation, plinth & walls: Laid without bond stone

Stone pitching/Dumping excluding cost of stone in horizontal on level.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level in 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources 6 graded stone aggregate 40 mm nominal size derived from natural sources)

Centering and shuttering including proping and removal of form work: Walls any thickness

Providing and fixing up to floor five level precast cement concrete solid block, including hoisting and setting in position With cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete : in 1:3:6

Providing & fixing stabilized mud concrete solid blocks (adobe) with 3% cement, masonry up to floor five level including hoisting and setting in position in mud mortar using approved quality mud with carriage of material complete.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. HRD bars

15 mm cement plaster on the rough side of single or half brick wall of mix: 1:6 (1 cement: 6 fine sand)

Providing and fixing of Angle iron post/channels/Flat iron & struts of required size including welding, nut-bolts, carriage all complete.

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Chajge. (Concealed work including cutting chases and making good the walls etc.) PN-16 Pipe, 25 mm OD

Providing fixing of wooden joist, beams etc including carriage and cost of necessary fixture items-Budloo

Providing, fixing of 19 mm thick ply for preperation of stage for various eves, including cost of nails, carriage etc complete and as per direction at site.

Supply and Laying of white lime marking on ground, road as and where required as per direction of engineer incharge.

Supplying fixing of inaugration stone with lazer carving, (content as directed)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):Second class kail wood

Providing and fixing soil waste & vent pipe (Prince or any other appoved brand as per Engineer In Charge

110mm dia PVC

75mm dia PVC

PVC Bend 110mm dia

PVC Bend 75mm dia

PVC Tee 110mm dia

PVC Tee 75mm dia

PVC Collar 110mm dia

PVC Collar 75mm dia

PVC trap 110mm dia

PVC trap 75mm dia

PVC Socket 110mm dia

PVC Socket 75mm dia

PVC door junction 110mm dia

PVC door junction 75mm dia

Providing and fixing water closet squatting pan ( Indian type W.C. pan) with 100 mm sand cast Iron P or Strap, 10 litre low level P.V. C. flushing cistern including flush pipe (of approved make) "manually controled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. (Note : It should have flush rate of with Flush rate of 4/2 Litre per Flush or less ) (Dual flush 4/2L WC cistern with bottom inlet for compact back to wall Rimless toilet)

Orissa pattern white vitreous china W.C. pan of size 580x440 mm with integral type foot rests. JAGUAR/CERA Make

Providing and fixing vitreous china dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required:

White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush bend.

Providing and fixing wash basin with C.I./M.S. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required:

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps JAGUAR / CERA/HINDWARE Make

Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required 510x1040 mm bowl depth 178mm.

Providing and fixing accessories of standard and quality make of approved manufacturer including all necessary fixtures required.

Classical cylinderical door lock for room door of approved brand Godrej or equivallent or as per engineer incharge

AL Drop for room doors of approved brand or as per site engineer

T- Bolt for doors of approved brand or as per site engineer

Handles for door of approved brand or as per site engineer

P/F CP brass toilet paper holder including cost of wodden,PVC,play etc.

Supply installation testing and commissioning of Geyser 15ltr Capacity horizontally mounted of approved brand (Havells/Bajaj/Crompton or any othet approved brand as per engineer in charge including all fixtures , bolts all complete

15 mm C.P. brass 2 in 1 tap of approved quality conforming to IS standards

15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931

15 mm nominal bore C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms

C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-incharge.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Supply installation testing and commissioning of Exaust Fan of approved brand (Havells/Bajaj/Crompton or any othet approved brand as per engineer in charge including all fixtures all complete

Supply installation of Soap dish approved brand as per engineer incharge

Providing and fixing SS locking grating (jali) anti-cockroach

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 25mm thick with 12.5 mm nominal size stone aggregate.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.

New work (Two or more coats applied @ 1.43 litre/10 sqm. Over & including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Preparing newly primed wooden surface for painting by way of filling of putty sand papering rubbing complete.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work.

P/f of glass panes 3-5mm thick with necessary nails and beading all job complete

Providing and installation of PUF (Puf Insulated Tanks) water tank capacity 1000 ltrs of approved brand (SYNTEX OR ANY OTHER APPROVED BRAND) as per direction engineer incharge

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.Complete job. Truss Area = 4400sft or @43 KG/SQM

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. Area =4000 sft or 389.63 sqm

Providing ridges or hips of width 60cm overall width plain G. S. sheet fixed with poymer coated J. or L hooks, bolts and nuts 8mm G. I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275gm /m2 specifications as per engineer in charge

labour charges for stone masonary work

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I.wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.

Providing and fixing panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for seperately,all complete as per direction of Engineer-in-charge.(second class wood 35 mm thick shutter)

Providing fixing paneling and glazing in panalled or panalled glazed shutters for door/windows 25mm to 40mm thick of 1st class kail wood.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, laid on 20 mm thick cement mortar 1:4 (1Cement : 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying 60mm thick faciory made cement in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately):Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade 1 Type II in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

Engagment of JCB on hourly basis works specified by site engineer

Engagment of tipper on per km basis

Supply and fixing of cloth of size and quality defined by site engineer for wrapping around stage

Supply and placing in position carpet of specified color and quality by site engineer

Providing and fixing inauguration board made of ACP sheet and acrylic sheet including all materials, labour and fittings complete which includes 3mm thick exterior grade ACP (Aluminium Composite Panel) sheet as base panel. 4mm thick premium quality acrylic sheet fixed over ACP. Lettering matter to be done in vinyl cutting / UV printing / laser engraved as approved. Stainless steel studs (25mm length) with caps for mounting

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including all necessary Fixtures complete

Please Enable Macros to View BoQ information