Comprehensive repairs to roofs, false ceiling, joineries, floors, brick works, plumbing and sanitary fixture, paving footpath and other misc repairs in 27 Camp, 28 Camp and CAD at YOL CANTT under AGE B/R-I OF GE (KH) YOL

Amount

PART-I:- Dismantling plain or corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof covering, all as specified.

Corrugated galvanized iron mild steel sheets 0.63mm thick, grade ‘O’, with 120 grams per square metre zinc coating fixed with 'J' or 'L' hook as in roof covering with two corrugation side lap. (Horizontal distance of side lap shall not be less than 145mm and depth of corrugation shall be 12.5mm), all as specified and directed.

All as per Serial Item No. 02 above but except sheet. (Note:- Serviceable pipe retrieved from Serial Item No 01 shall be used).

0.63mm thick plain galvainsed mild steel sheeting in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275, complete, all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

Dismantling wrought iron or mild steel work of any description. all as specified.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe.410W Gde-E-250 quality A, steel work, complete all as specified.

Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc. conforming to grade Fe.410-W.Gde-E-250 quality A, steel work, all as specified.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets in ceiling, all as specified.

S & F for false ceiling of 600mmx 600mmx 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws (e-boards) manufactured from homogeneous mixture of cement, quartz and cellulose and cured with high pressure steam using auto claving process conforming IS-14862, including Gl frame work square pattern of grid size 605mmx 605mm for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, complete all as specified and directed.

Dismantling timber scantlings 40 sqcm and over in section, in any position, unframed work, complete all as specified.

2nd class hard wood (Kail) as in scantling clean sawn timber fixed in unframed work, complete, all as specified.

2nd class hard wood (Kail) as in scantling wrought fixed in unframed work, complete, all as specified.

Dismantling timber scantlings 40 sqcm and over in section, in any position, framed work, complete all as specified.

2nd class hard wood (Kail) as in scantling wrought fixed in framed work, complete, all as specified.

Applying two coats of creosote oil on new wood or wood based surfaces of any description, exc. 10cm width or girth including preparation of surfaces, all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each and removing from site, all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4 Sqm each and removing from site, all as specified.

Taking down shutters of any description not exc. 1 Sqm each and removing from site, all as specified.

Taking down shutters of any description exc. 1 Sqm not exc. 2 Sqm each and removing from site, all as specified.

Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) door shutter with frame, partly glazed with 5mm thick tinted glass and partly panelled with 12mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150mm size, aluminium barrel tower bolt 200mm size, including hydraulic door closer,etc all as specified below complete all as specified and directed. (a) Frame (top & side) section shall of size 101.60 x 44.75 x 2.4mm (Section No 14021). (b) Vertical Members of shutter section shall be of size 85.00x44.45x2.00mm (section No 19560). (c) Top Members of shutter Section shall be of size 83.50 x 44.45 x 2.00mm (section No 19581). (d) Lock rail (Middle member) of shutter section shall be of size 150.00x44.45x3.00mm (section No 19596). (e) Bottom Members of shutter section shall be of size 150.00x44.45x3.10mm (section No 19584). (f) Glazing clip for securing glass of shutters shall be of 0.80mm thick (section No 19370). Note:- (i) Section No given above are of make jindal, Contractor may use similar section of other make mention in Appx 'C'

Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

S & F aluminium (powder coated with approved colour) ventilator, partially glazed and partially louvers, outer frame & mullion fabricated with aluminium section of size 82.50mmx 38.00mmx 1.50mm thick (Cat No 20036), half portion glazed with 4mm thick frosted glass including rubber beading, & glazing clip, half portion louvers of 80mm wide & 4mm thick frosted glass including aluminium louver patti incluidng S.S wire gauge of fixing of 0.36mm dia and 1.40 width of aperture with 25x3mm think aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in position complete. Note:-(i) Section No given above are of Make-Jindal, contractor may use similar section of other make mention in Appx 'C'

2nd cla hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed

Factory made 2nd class hard wood (Sal/ Hollock) plain, framed, panelled 35mm thick shutters without interlocking rail and with one panel and panels of 9mm BWP commercial plywood or 12mm veneered particle with commercial face veneers on both sides.The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, all as specified.

Factory made second class hard wood (Sal) glazed and Skelton door shutters 35mm thick open rebated and prepared to receive glass gauge etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass or gauge etc., size of members of shutter as specified in clause 8.24 (a) of part-I, fitted to chowkats, complete all as specified.

35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, all as specified.

Applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surfaces of any description, exc. 10cm width or girth including preparation of surfaces, all as specified.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 180 of MES SSR 2020 Part-II.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5 mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1) specified and directed.

18/19mm thick block boards, grade 2 quality, interior grade,with decorative face veneer on both faces, fixed with screws to timber frame-work, all as specified.specified.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised Width of flaps (when open) in 40mm, all as specified.

Butt hinges (ISI marked), medium weight, cold rolled, mild steel 100mm long, all as specified.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 200mm, fixed, all as specified.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 150mm, fixed, all as specified.

Extruded aluminium alloy handles (ISI marked, fabricated type, anodised, of size 100mm, all as specified.

Extruded aluminium alloy handles (ISI marked, fabricated type, anodised, of size 125mm, all as specified.

Hasp and staple, safety type, aluminium with mild steel hinge pin including bolt to hinge plate and fixed with screws of size 100mm, all as specified.

Aluminium alloy, anodised, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 250mm with lipping frame to match, all as specified.

Mild steel flat iron as in holdfast of size 25x3mm thick of Fe 290 Gde 165, complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 with using 20mm graded stone aggregate as in bed block, bed plates etc. For embedding hold fasts etc. Complete all as specified and directed.

Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 60mm x 25mm double rebated comprises gauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick required no of each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including following fitting welded to frame shutter:-(i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window. (ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf. (iii) MS tower bolt 150mm long - 2 No per leaf. (iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf. (v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf. (vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf. (vii) Flat iron fillets of size 20X3 mm for fixing wire gauge. (viii) MS work with angle or other section as in window gurad bars, grill (ix) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 26/03. if iron scrap retrived under this item shall be sold to contractor under Sch of credit. Make : As per Appendix 'C'.Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day.

Chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165.

Stainless steel wire cloth. 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples or wooden beads, complete all as specified.

Stainless steel wire cloth. 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples or wooden beads, fixed in repairs, complete all as specified.

Second class Plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads sectional area exc 6 & n. exc 13 sqcm including taking out old, complete, all as specified.

Small fittings of 2nd class hard wood (SAL) such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including 50mm long, medium weight, cold rolled mild steel butt hinge, articles not exc. 200 cu.cm. each including preparation of articles and applying two coats of synthetic enamel paint over a coat of pink primer, all as specified.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm, fixed in repair, complete all as specified.

S&F MS prepainted sheet type door spring heavy duty, 200mm long including roller and roller plate, complete all as specified and directed. Make:- Ritff, Everst

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads and removing from site, all as specified.

Sheet glass 4.80mm thick ordinary quality and glazing with oil putty wooden beads in squares, not exc. 0.5sqm in each pane, complete all as specified.

Sheet glass 3mm thick ordinary quality and glazing with oil putty/aluminium beads in squares, not exc. 0.5sqm in each pane, complete all as specified.

3mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 Sqm in each pane, complete all as specified.

Applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, all as specified.

Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins arches, pillars, including removal of debris to a distance exc 1.5 km but n.exc 2 Km, all as specified and as directed.

Walling random rubble masonry with best quality locally available stone, uncoursed, well bonded, bedded, solidly hearted and built in cement mortar 1:6 (1 cement : 6 coarse sand), all as specified. Note:- Locally available slate stone not shall be used.

All as per item No. 57 above but except stone.

Brick work with old size fly ash bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 (1 cement : 4 coarse sand), all as specified.

Plain cement concrete M-15, nominal mix, B-1 using 20mm graded mechanically crushed stone aggregate as, in lintels upto 1.50 metres clear span cuts, steps seismic and other similar bends, coping, bands plates for serving hold fasts etc. and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as specified.

Plain cement concrete M-10 nominal mix, type C-1 using 20mm graded mechanically crushed stone aggregate as in surface channel and drains all as specified.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work not exc 20cm wide for roughly finished flat surfaces of concrete, all as specified.

Forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds etc. all as specified.

Taking down cement plaster on brick or stone walls, ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete including removal of debris to a distance exc 1.5 km but n.exc 2 km, all as specified and as directed.

Rendering cement plaster 15mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) on fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering cement plaster 5mm thick in cement mortar 1:3 (1 cement : 3 coarse sand) on fair faces of RCC concrete surfaces and including applying cement slurry in bottom of slab, chajjas, fin, facias etc, complete all as specified and directed.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, mixed with WPC, all as specified. Note : Supply only Water proofing compound shall be measured and paid for seperately.

Rendering plaster 15mm thick in cement mortar 1:6 (1 cement :6 coarse sand) on other than fair faces of brick wall or stone wall surfaces, surface finished even and smooth without using extra cement, all as specified.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over 2mm thick wall care putty, complete, all as specified.

Three coats of white wash on newly plastered surfaces of ceiling including preparation of surface complete, all as specified and as directed.

Two coats of cement base paint on newly plastered surface of wall over a coat of primer including preparation of surface complete all as specified and directed.

Supply only intergal water proofing compound, complete all as specified.

Demolition of cement concrete (unreinforced) in ground floors and paving, not exceeding 15cm thickness (below or above ground level), un-reinforced including removal of debris to a distance exc 1.5 km but n.exc 2 km, all as specified and as directed.

Dismantling stone slabs and tiles of any description or thickness, laid bedded and pointed in any mortar in floors, aprons etc. including removal of debris to a distance exc 1.5 km but n.exc 2 km, all as specified and as directed.

Marble 14 to 16mm thick, green marble, (table rubbed and polished) as in kitchen cooking platform /shelf and verticle surfaces duly machine cut in skirting /dado and like laid over and including 15mm thick screed bed in cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade green marble type, all as specifiedand directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish of the premisses, complete including removal of debris to a distance exc 1.5 km but n.exc 2 km, all as specified and as directed.

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.06 Sqm but not exc. 0.11 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand) complete, all as specified.

Glazed coloured tiles of size 300x200x7mm thick as in vertical surfaces such as jointed in neat cement slurry and pointed with coloured cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Plain cement concrete M-15, nominal mix, type B-0, using 12.5mm graded mechanically crushed stone aggregate as in floors, 25mm thick, surface finished even and fair to receive top surface, all as specified.

75mm thick Plain cement concrete M-15 nominal mix, B-2, using 40mm graded mechanically crushed stone aggregate as in sub base complete all as specified.

Chequered cement concrete tiles machine pressed of size 20cmx20cmx 25mm thick with grey cement, set jointed & pointed in neat cement slurry mixed with pigment to match the shade of the slab in floors laid over and including 15mm thick screed bed in cement mortar 1:4 complete, all as specified.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment laid over and including 50mm thick sand cushion, joints of tiles filled with dry sand and compacted with mechanical vibrator complete all as specified and directed.

Machine cut kota stone slab flooring 14-16 mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 20mm screed layer in cement mortar 1:4 (1 cement : 4 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish complete, all as specified.

Machine cut kota stone slab 14-16 mm thick as per sample kept in GE’s office, as in vertical surfaces such as skirting/dado/riser to steps laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, laid over and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) including cutting, rubbing, grinding and polishing to achieve mirror finish complete, all as specified.

Demolition of cement concrete (reinforced) in any description and in any position not otherwise specifically provided, including removal of debris to a distance exc 1.5 km but n.exc 2 km, all as specified and as directed.

Reinforced cement concrete, M-15 (Nominal mix), type B-1, (with 20mm graded crushed stone aggregate as) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, including formwork, all as specified.

TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, all as specified.

Taking up or down 15mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.

Mild steel galvanized iron water tubing 15mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.

All as per Serial Item No 89 above but except pipe. (Note:- Serviceable pipe retrieved from Serial Item No 88 shall be used).

Taking up or down 20mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.

Mild steel galvanized iron water tubing 20mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.

All as per Serial Item No 92 above but except pipe. (Note:- Serviceable pipe retrieved from Serial Item No 91 shall be used).

Mild steel galvanized iron water tubing 25mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor, including taking up or down old, complete, all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick walls, complete all as specified.

Sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x160mm and fixed in repair, complete all as specified.

Wash basins, Vitreous China (Flat back type) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with CP coupling nuts at both ends, waste pipe of polythylene of low or high density or PVC of 32mm dia including Pillar taps fancy type, 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed in repair, complete all as specified.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed of 15mm bore and fixed in repair, complete, all as specified.

Stop valve, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repairs complete, all as specified.

Stop valve, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repairs complete, all as specified.

Angle valve, cast copper alloy, fancy type chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repair complete, all as specified.

Bib taps, fancy type 15mm bore, cast copper alloy with crutch or butterfly handle, screwed down, chromium plated screwed for iron pipe or for brass ferrule and fixed in repairs, all as specified

Vitreous China wash down water closet (pedestal pattern), coloured including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC coloured seat cover and chromium plated jet including PVC connection, fixed complete, including PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve, float and handle with brackets with PVC 32mm dia flushing pipe, anti-syphonage pipe, fixed in repair, complete all as specified.

Supply only Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device.

S&F in repair vitreous china premium/1st quality wash down water closet wall hung EWC white/ivory/gel gasket etc. Including fixing of plastic water closet seat cover, block/white closed pattern with flat bottom and cover and mild steel chromium plated hinging device, flushing cistern, (excluding cistern, flush pipe), complete all as specified and directed.

Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with PVC ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-I using 20mm graded crushed stone aggregate complete all as specified,including PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve, float and handle with brackets with PVC 32mm dia flushing pipe, anti-syphonage pipe, fixed in repair, complete, all as specified.

Supply only High density polyethylene (HDPE) pipes of pressure rating 6 kgf/sqcm of 32mm bore.

Supply only High density polyethylene (HDPE) pipes of pressure rating 6 kgf/sqcm of 40mm bore.

Supply only PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve, float and handle with brackets.

Supply and fixed in repair PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve, float and handle with brackets including 32mm dia PVC long bend flush pipe 90cm long snd 15mm dia PVC connection 600mm with CP brass coupling nuts and PVC washers at both ends, fixed complete, all as specified.

Vitreous China bowl Urinal, flat back 465x355x265mm, white (white (minimum) with grating and union for discharge pipe, complete including providing and fixing plugs, beding urinal against wall in cement mortar 1:2 securing urinal plugs with and including 60mm long brass screws, pointing around urinal back in cement, including 32mm bore PVC waste pipe, complete fixed in repair, all as specified.

S&F in repair 25mm dia powder coated mild steel, chromium plated curtain rod including brackets.

Disconnecting existing PVC/ferro cement/MS tanks capacity exc.250 litres but n. exc 500 litres, setting aside (or lowering if required) for cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. and hoisting if required reconnecting and re-fixing in position, all as specified.

Disconnecting existing PVC/ferro cement/MS tanks capacity exc.500 litres but n. exc 1000 litres, setting aside (or lowering if required) for cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. and hoisting if required reconnecting and re-fixing in position, all as specified.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position inbcluding brass ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including dismantling old cemented/ asbestos water/ PVC storage tank, all as specified.

Rotational moulded polyethylene water storage tank 1000 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position inbcluding brass ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including dismantling old cemented/ asbestos water/ PVC storage tank, all as specified.

S & F in repair 3mm thick backelite sheet (Hylem) as sheet cover with PVC box of size 4"x4" for fixing switches, sockets & regulator etc complete all as specified and directed.

S&F in repair switch socket combination outlet 2 in 1, 3 pin 6 Amps Flush type all as directed.

S & F in repair 3mm thick backelite sheet (Hylem) as sheet cover with PVC box of size 7"x4" for fixing switches sockets & regulator etc complete all as specified and directed.

S&F in repair switch socket combination outlet 2 in 1, 3 pin 16 Amps Flush type all as directed.

S & F in repair Switch piano, flush type single pole, one way 6 Amp SP 230 Volts all as specified.

Taking down existing electric boards from walls and refixing in same position all as specified and directed.

M S ASSOCIATES

M/S VIG AND COMPANY

M/S KHANNA CONTRITION COMPANY

M/S JATINDERA ENTERPRISES