SPECIAL REPAIR TO BUILDING NO P-32 (JCOs CLUB) AND CERTAIN MINOR/REVENUE WORKS AT MILITARY STATION KOTA

Amount

Demolition of cement concrete (unreinforced) in ground floor and pavings n.exc 15 cm thickness (below or above GL), complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate), 75 mm thick as in plinth protection/Path/PCC paving etc including finishing the surface even & smooth without using extra cement, with and including all necessary formwork to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm wide joints throughout the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three parts of fine sand by weight), complete all as specified & directed.

M&L 75 mm thick PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in sub base of floors etc, complete all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B-0 (using 12.50 mm graded stone aggregate) as in flooring/sub base finished even and rough to receive floor finishes/screed, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing tiles and rubbish off the premises, complete all as specified and directed.

M&L Glazed ceramic coloured tiles on vertical surfaces 350x 250x7 mm/450X350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick rendering in CM 1:4, complete all as specified and directed.

M&L for non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for machine cut kota stone slab as in flooring 17 to 22 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for machine cut kota stone slab as in skirting, dado, risers etc, 17 to 22 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing, laid over and including 10 mm thick CM 1:4 backing, complete all as specified and directed.

M&L for cutting/grinding of the existing marble/kota stone flooring by mechanical process using carborundum stone of appropriate grit size, cleaning and finally mirror polishing by applying wax polish, complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors etc, laid, bedded and pointed in any mortar, complete all as specified and directed.

M&L granite slab 18-20 mm thick, table rubbed and polished in cooking platform, jambs, cills, pillars, tread, risers, platform for WHB etc including bull nosing to exposed outer edges, set in CM 1:4 bedding and pointing with white cement mixed with pigment, complete all as specified and directed.

M&L for cutting 25 mm dia hole in stone slab for passing through cooking gas pipe, complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work & precast concrete articles, complete all as specified and directed.

M&L brick work with pulverized fuel Ash-lime bricks (old size fly ash bricks), straight or curved on plan exc 6 m mean radius, built in CM 1:6, complete all as specified and directed.

M&L for brick work with pulverised fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan to any radius in half brick walls built in cement mortar 1:4, complete all as specified and directed.

M&L walling of random rubble, uncoursed well bonded, bedded and solidly hearted, built in Cement Mortar 1:4, complete all as specified and directed.

M&L PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in foundation, filling, mass concreting etc, complete all as specified and directed.

M&L Providing cement concrete 1:2:4 type B-0 using 12.50 mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L PCC 1:2:4 type B-2 using 40 mm graded stone aggregate as in surface channel and drains, complete all as specified and directed.

M&L PCC 1:4:8, type D-2 using 40 mm graded stone aggregate, as in concrete bed to drain pipes including packing under and haunching against the sides of 150 mm dia pipe, after they are laid and tested, complete all as specified and directed.

Taking down cement plaster any description/thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair faces of brick work or stone masonry surfaces in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 15 mm thick rendering on other than fair faces of brick work or stone masonry surfaces in CM 1:4 with using WPC as per manufacturer's instructions, finishing surfaces even and smooth without using extra cement, complete all as specified and directed. (Note: WPC shall be measured and paid separately under appropriate item.)

M&L preparing newly plastered surfaces of walls and applying two coats of cement based paint over a coat of primer, complete all as specified and directed.

M&L rendering 5 mm thick in CM 1:3 on concrete surfaces of ceiling, finished even and smooth without using extra cement, complete all as specified and directed.

M&L applying three coats of white wash after preparation of new plastered surfaces of ceiling, complete all as specified and directed.

Supply only liquid water proofing compound as approved by the GE, complete all as specified and directed.

M&L for preparation of new surfaces of walls and applying two coats of distemper oil emulsion over a coat of primer, complete all as specified and directed.

M&L for applying three coats of white wash on walls including preparation of newly palstered surface, complete all as specified and directed.

M&L applying two coats of white wash after preparation of old previously treated plastered surfaces of ceiling, complete all as specified and directed.

M&L complete removal of existing treatment from previously treated surfaces of walls and applying 3 mm thick Wall care putty as per manufacturer's instructions and over it applying two coats of distemper oil emulsion over a coat of primer, complete all as specified and directed.

M & L for preparation of old painted iron/steel surfaces of any description not otherwise described, over 10 cm in width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M & L for preparation of old painted surfaces of wood or wood based materials of any description not otherwise described, over 10 cm in width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Cutting chases pinning in, making good to facing where required and pointing in CM (1:3) to ends of edges of landings, shelves, cills, lintels etc and making good cutting, girth not exc 10 cm, in brick walls, complete all as specified and directed.

Taking up or down 15 mm dia steel tubing and connection including cleaning for refixing or removal to store, complete all as specified and directed.

Taking up or down 20 mm dia steel tubing and connection including cleaning for refixing or removal to store, complete all as specified and directed.

S&F 15 mm dia GI tubing, medium grade, with all fittings and fixed complete to walls, ceilings and floors complete all as specified and directed.

S&F 20 mm dia GI tubing, medium grade, with all fittings and fixed complete to walls, ceilings and floors complete all as specified and directed.

S&F in repair bib taps, cast copper alloy, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm dia GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F in repair anglular stop valve 15 mm nominal dia cast copper alloy, chromium plated, screwed down high pressure with crutch or butterfly handle, screwed one end for iron pipes or for unions and fixed, complete all as specified and directed.

S&F in repairs stop valves, fancy type, chromium plated brass with long shank and cup (Concealed type), screwed down, high pressure, both ends screwed to iron pipe or for union, dia of pipe 15 mm, complete all as specified and directed.

S&F pillar taps, cast copper alloy, with capston heads, fancy type, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm dia iron pipe and fixed, complete all as specified and directed.

S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest incl providing lime concrete bedding and connecting to flusing cistern, complete all as specified and directed.

S&F in repair white vitreous china wash down water closet pan (pedestal pattern), including white plastic seat cover with flat bottom and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

S&F in repair 10 Ltr capacity PVC low level flushing cistern, top push type with inlet ball valve, PVC float, brackets including superior quality PVC flush pipe of 32 mm dia, complete all as specified and directed.

S&F in repair 'D' type towel rail 60 cm long, stainless steel, fancy type, 20 mm dia, fixed with stainless steel screws, complete all as specified and directed.

S&F in repair shower rose, chromium plated brass, fancy type, 125 mm size with swivel joint, screwed to iron pipe or for union of 15 mm dia, complete all as specified and directed.

S&F in repairs PTMT alloy toilet cabinet with mirror of overall size 350x450 mm and fixed to wall complete all as specified and directed, complete all as specified and directed.

S&F PVC connection, 15 mm size with two PTMT nuts, length of connection 450 mm, complete all as specified and directed.

S&F in repair stainless steel tubular curtain rods, 25 mm dia, with fixing brackets and one pair of decorative end caps etc, complete all as specified and directed.

S&F in repair vitreous china half stall type urinal, white with grating and union for discharge pipe, including providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back with white cement, complete all as specified and directed.

S&F vitreous china urinal partition, white, size 310x700 mm, fixed to wall and pointing around edges in white cement, complete all as specified and directed.

S&F 300 mm size corner type toughened glass shelf of 6 mm thick glass and CP guards of approved quality and fixed to wall with SS screws including dash fastener etc, complete all as specified and directed.

S&F soap dish made of stainless steel, approx size 160x100 mmx 1 mm thick, fixed to walls with plugs & SS screws, complete all as specified and directed.

Demolition/Dismantling of existing normal roof treatment, any type from RCC roof slab including lime concrete/PCC padding over roof, removing layer of bitumen under lime concrete/PCC padding, cement mortar, felt etc and cleaning the surface by hacking to receive plaster and removing demolished materials outside MD land, complete all as specified and directed.

M&L brushing neat cement slurry with 3.00 kg cement per Sqm, complete all as specified and directed.

M&L for PCC 1:2:4 mix type B-0 (Using 12.5 mm graded stone agg) for roof padding, leveling course to receive floor finishes etc, complete all as specified and directed.

M&L for cleaning of roof slab including picking, sweeping clean and washing down with water to remove dust, dirt etc and Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to IS 3384 @ of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of cold applied bituminous primer conforming to IS:3384 @ 0.40 Kg/Sqm.

Item 61.00 Contd........ (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm (minimum) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimney/other vertical surfaces and polymeric membrane inserted in groove and sealed with paving bitumen. (v) Cost of above aspects is deemed to be included in quoted rates.

M&L for applying 10 mm thick screed in CM 1:3 on roof slabs with using liquid water proofing compound as per manufacturer's instructions, complete all as specified and directed. (Liquid WPC shall be measured and paid separately).

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 10 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide for fair finished surfaces, complete all as specified and directed.

Formwork (rough finished surfaces) Chhajja, chullah hoods, weather shades, corbels, water troughs and similar items including edges, complete all as specified and directed.

M&L for RCC 1:1.5:3 type A-1 (using 20 mm graded stone aggregate), as in chhajjas, facias etc, complete all as specified and directed.

M&L mild steel TMT bars, 6 to 8 mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for column, hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia, complete all as specified and directed.

Dismantling loose concrete cover of RCC columns, beams and the like, area not exc 1.50 Sqm each, roughening and cleaning of concrete surfaces with steel wire brushes, washed with water and allowed to dry including dusting of steel reinforcement, providing welded mild steel wire fabric of mesh size 75 x 75 mm and 2 mm nominal dia of wire as reinforcement to concrete surfaces, applying adhesive/admixture over steel mesh and providing ordinary portland cement 53 grade and 2 parts of sand mixed with admixture at the rate as per manufacturer's instructions with a pressure of 2 to 2.5 Kg/Sqcm by guniting machine including necessary padding, steel scaffolding and shuttering for working platform/formwork etc, complete all as specified and directed.

All as per item 68.00 herein before above but area exc 1.50 Sqm each, complete all as specified and directed.

S&F 75 mm dia PVC (SWR) floor trap, with CP grating including jointing to waste pipe with solvant cementt and fixed in cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate), complete all as specified and directed.

S&F in repair PVC (SWR) pipe 75 mm bore, single socketed, in any length with rubber ring joints and fixed to walls, complete all as specified and directed.

S&F in repair PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and fixed to walls, complete all as specified and directed.

S&F in repair PVC (SWR) pipe 75 mm dia, single socketed, in any length with rubber ring joints and laid in trenches/floor, complete all as specified and directed.

S&F in repair PVC (SWR) pipe 110 mm dia, single socketed, in any length with rubber ring joints and laid in trenches/floor, complete all as specified and directed.

S&F in repair PVC (SWR) bend 75 mm dia, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F in repair PVC (SWR) 75 mm dia single Junction 'T', equal or unequal, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

S&F in repair PVC (SWR) 110 mm dia single Junction 'T', equal or unequal, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

S&F in repair PVC (SWR) bend 110 mm dia, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F 500 Ltrs capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl dismantling existing water tank, complete all as specified and directed.

S&F gun metal globe or gate valve of size 20 mm dia with iron wheel head screwed both ends and for iron pipe & fixed, complete all as specified and directed.

S&F in repair sand cast iron soil, waste and vent pipe 100 mm bore in any length with or without ears with cement joints fixed to wall, complete all as specified and directed.

S&F in repair sand cast iron soil, waste and vent pipe 75 mm bore in any length with or without ears with cement joints fixed to wall, complete all as specified and directed.

S&F in repair 100 mm bore CI bend (any radius), diminishing pieces or tapers (larger bore measured), complete all as specified and directed.

S&F in repair 75 mm bore CI bend (any radius), diminishing pieces or tapers (larger bore measured), complete all as specified and directed.

S&F in repair CI branch pieces 100 mm bore single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified and directed.

S&F in repair CI branch pieces 75 mm bore single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified and directed.

S&F stack clamps made out of 50x5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, bore of pipe 100/110 mm, complete all as specified and directed.

S&F stack clamps made out of 50x5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, bore of pipe 75/80 mm, complete all as specified and directed.

Taking down chowkhat or frames not exc 1.50 Sqm each with shutters (without taking off shutters from the frame), complete all as specified and directed.

Taking down chowkhat or frames exc 1.50 Sqm and not exc 4.00 Sqm each with shutters (without taking off shutters from the frame), complete all as specified and directed.

Taking down shutters of any description not exc 1 Sqm each, complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm and not exc 2 Sqm each complete all as specified and directed.

S&F 35mm thick factory made IInd Class Hard wood (Hollock) paneled door shutters single panel with lock rail and panel of 9mm B.W.P. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to IS-710 or 12mm thick particle board veneered with commercial veneering on both faces. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S&F 35mm thick factory made IInd Class Hard wood (Hollock) glazed and skeleton, open rebated, prepared to receive glass, gauge etc, without sash bars, edges of framing plain, chamfered and rounded, fitted with cut and mitered beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S&F steel windows or ventilators with side hung shutters including box type friction hinges, steel handle and steel peg stay, complete without glazing bars, including one shop coat of zinc chromate primer, complete all as specified and directed.

S&F steel windows or ventilators with side hung shutters including box type friction hinges, steel handle and steel peg stay, complete with glazing bars, dovetailed or welded including one shop coat of zinc chromate primer, complete all as specified and directed.

M&L Running welding in repairs n. exc. 6 mm metal thickness to be welded, exc 2.5 cm but not exc 5 cm in length, complete all as specified and directed.

S&F 18/19 mm thick block boards, grade 1 quality, exterior grade, commercial type, fixed with screws to timber frame work with 6 mm thick teak wood lipping on exposed edges, complete all as specified and directed.

S&F continuous piano hinges, made of stainless steel, 30 mm width of flaps when open, complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length of cover plate 140 mm, complete all as specified and directed.

S&F 300 mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

S&F 150 mm aluminium anodised, barrel tower bolts of extruded section, complete all as specified and directed.

S&F 100 mm size mild steel butt hinges, medium weight, cold rolled and fixed with screws, complete all as specified and directed.

S&F 100 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified and directed.

S&F 250 mm aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and directed.

S&F 150 mm size aluminium handles, cast type, anodised, complete all as specified and directed.

S&F 100 mm size aluminium handles, cast type, anodised, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F sheet glass 3mm thick ordinary quality and glazing with oil putty etc in squares n.exe 0.50 Sqm in each pane, complete all as specified and directed.

S&F figured/pin head glass 3mm thick ordinary quality and glazing with oil putty in squares n.exe 0.50 Sqm in each pane, complete all as specified and directed.

Hacking out old broken glass (any thickness size, quality or description) from wooden frames or stone concrete or brick surrounds, glazing with putty or fixed with beads, complete all as specified and directed.

S&F brass knobs 40 mm dia, bright polished, fancy type, fixed with brass screws, complete all as specified and directed.

S&F 100 mm Hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed.

M & L for preparation of new or previously untreated wood or wood based surfaces, exceeding 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

M&L for PCC 1:3:6 mix type C-1 (Using 20mm graded stone agg) as in bed blocks for fixing hold fasts, bolts etc, complete all as specified and directed.

S&F rolled MS angle iron conforming to Fe-290 Gde E-165 as in door frame of any size including flat iron thresh hold, flat iron hold fast in back of chowkhats as back plate for support of machine screws including drilling holes and making threads, complete all as specified and directed.

M & L for preparation of new or previously untreated steel surfaces not exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer, complete all as specified and directed.

S&F in repair sink without draining board made of stainless steel 1mm thick with plugs, washers and waste coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets of suitable angle iron, 32 mm dia superior quality PVC waste pipe and connecting union to pipe overall size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F in repairs stainless steel utensil plate rack of size 910x780x250 mm, made of 0.80 mm thick stainless steel sheet and fixed in position, design and pattern as approved by the GE, complete all as specified and directed.

S&F in repairs 19 mm thick prelaminated MDF board, exterior grade (Grade I, type 2), both side off white shade or shade as approved by Engineer in Charge, fixed as in shutters, shelves and partitions of kitchen cabinet, complete all as specified and directed.

S&F in repairs auto close hinges, stainless steel, bright or matt finish, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

S&F mild steel framed work as in grills, grating etc. with end of bars shouldered and/or riveted, or forged into spikes: framed guard bars: barred iron doors: ladders: frame balusters: walk ways: railing: frame work of water tanks and similar works conforming to Fe-290 Grade-E-165, complete all as specified and directed.

S&F Wire netting of galvanised steel wire 2.00 mm dia fixed with tinned tacks of wire staples, size of mesh 20 mm, complete all as specified and directed.

M & L for preparation of new or previously untreated steel surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer, complete all as specified and directed.

S&F 1.00 mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required, complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing, complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as specified and directed.

S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates, sliding track frame for sliding windows etc, including joining cleat for fixing etc. complete all as specified and directed.

S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium window and ventilator shutters, sliding type without sash bars, aluminium sections weighing not less than 0.32 kg/m including necessary joining cleats, glazing clips, rubber packing, screws, anodised aluminium fittings such as suitable handle (1 No.), slide lock device etc, complete all as specified and directed.

Supply only stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm, complete all as specified and directed. (Note: cost of fixing of wire cloth shall be deemed included in the unit rates of aluminium shutters.)

Cutting holes into or through brick walls/stone masonry built in cement mortar not exc. 150 Sqcm and making good in CM 1:3 or cement concrete 1:2:4 type B-1(using 20 mm graded stone aggregate) depth exc. half brick and not exc. one brick thick, complete all as specified and directed.

M&L for preparing new previously untreated plastered surfaces of walls and applying two coats of modified exterior acrylic emulsion paint over a coat of primer, complete all as specified and directed.

S&F 20 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe, complete all as specified and directed.

S&F 4 way diverter for concealed fitting with built in non return valve and diverter handle including taking out of old wall mixer, complete all as specified and directed.

S&F in repair towel rack of stainless steel, size 600x250 mm, fixed with and including CP brass screws and wooden/plastic cleats, complete all as specified and directed.

S&F in repair vitreous china wash hand basin white with flat back of size 550x400 mm provided with vitreous china white pedestal, excluding chain and plug and stopper but including 32 mm bore CP waste coupling, superior quality PVC waste pipe of 32 mm bore and two 600 mm long cast iron brackets, complete all as specified and directed.

S&F 15 mm bore fancy type chromium plated brass centre hole basin mixer for mixing hot and cold water, screwed down for iron pipe and fixed, complete all as specified.

S&F circular towel ring made of stainless steel, 200 mm dia, fixed to PVC rawl plugs with stainless steel screws, complete all as specified and directed.

S&F 100mm cast iron sanitary connection socket to fit WC out-let, complete all as specified and directed.

S&F in repair 100 mm dia cast iron floor trap, with CP grating including jointing to waste pipe and fixed in cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) complete all as specified and directed.

M&L for 150 mm dia salt glazed stoneware drain pipes, laid in trenches and jointed in cement sand slurry in 1:1, complete all as specified and directed.

M/L for 50mm thick rough dressed stone slabs for manhole covers n.exc 2 mtr in length, punched dressed on face and along exposed edges, self faced on other side and sets and pointed in cement mortar 1:4 complete all as specified and directed.

M&L complete removal of existing treatment from previously treated surfaces of walls and applying two coats of modified exterior acrylic emulsion paint over a coat of primer, complete all as specified and directed.

S&F ABS body health faucet (Bidet spray) in chrome finish, including 15 mm dia chromium plated pop up connection pipe of minimum 1.00 m length with CP brass nuts, complete all as specified and directed.

S&F in repairs 15 mm dia two way angular stop cock, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed to iron pipe or brass ferrule, complete all as specified and directed

S&F salt glazed stone ware gully traps, square or round mouthed, type 'P', size 150x150 mm, with and including bedding in PCC 1:5:10 type E1 using 20 mm graded stone aggregate, complete all as specified and directed.

S&F in repair 100 mm dia cast iron soil, waste & vent pipes, with or without ears, in any length, with cement joints, laid in trenches or under floors complete all as specified and directed.

S&F in repair 75 mm dia cast iron soil, waste & vent pipes, with or without ears, in any length, with cement joints, laid in trenches or under floors complete all as specified and directed.

S&F CI cowl 100 mm bore, fixed with cement joint, complete all as specified and directed.

S&F CI cowl 75 mm bore, fixed with cement joint, complete all as specified and directed.

Dismantalling wall and ceilling board or insulation board incl cover fillets complete all as specified and directed.

S&F Anodised aluminium snap grid frame work for false ceiling, size of grid 605x605 mm, complete all as specified and directed.

S&F 10 mm thick PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling grid made of Aluminium/G.I./M.S. as per specification and drawing, complete all as specified and directed.

M&L for light coloured vitrified tiles, 10mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for rounding to edges of kota stone/marble stone/granite stone of 15 to 25 mm thickness by making stone bull nosed/rounded as in floor, steps, platform etc, complete all as specified and directed.

S&F in repair at any height false ceiling of 12 mm thick tapered edge gypsum board conforming to IS-2095 including S&F of frame work made of special section power pressed from MS sheet and galvanised in accordance with zinc coating and consisting of angle clamps of size 25 mm wide 1.60 mm thick with flange of 22 mm and 37 mm at 1200 mm c/c including jointing and fixing to a flush and square edge of the gypsum boardw with recommended filler taper taps finisher and two coats of plastic emulsion paint over one coat of primer, complete including leaving opening for ceiling lights with perimeter channels, complete all as specified and directed.

M&L 100 mm thick PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in sub base of floors etc, complete all as specified and directed.

M&L for laying fully vitrified paving tiles of size 300x300x20 mm thick suitable for exterior areas, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles, laid over and including 15 mm thick screed in CM 1:6, complete all as specified and directed.

M&L Providing cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in in roof kerbs or mud stops, for packing sides of interlocking tiles etc, rounded or chamfered on edges, complete all as specified and directed.

M&L for rolled mild steel work as in joist, channels, angle, tube or Tee section fixed independently without connecting plates etc, cut to ordinary length ie 20 mm of the length indicated, conforming to Fe-290 (Gde E-165), complete all as specified and directed.

S&F rolled mild steel work as in roof trusses (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) incl distance pieces cleats etc conforming to Fe-290 Grade-E-250, complete all as specified and directed.

S&F Prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and directed.

S&F Wire netting of stainless steel wire 1.0 mm dia fixed with stainless steel wire staples, size of mesh 20 mm, complete all as specified and directed.

S&F in renewal factory made pressed steel cupboard shutters alongwith frame, frame made of 1.25 mm thick PBI sheet and shutter made of 1.00 mm thick PBI sheet with 6 Nos 3.15 mm thick and 100 mm long steel hinges per shutter, godrej pattern locking arrangement with 12 mm dia vertical rod and lock with duplicate key & chrome finish handle, duly spray painted in factory with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer, complete with fastener, hold fast etc as required at site, complete all as specified and directed. (Total width including frame shall be measured for payment purpose).

M&L hardcore (broken stone) of gauge not exc 63 mm, deposited spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil, complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m deep for foundation etc or for shafts, column footings or for laying cables etc not exc 10 Sqm on plan and getting out in hard/dense soil, complete all as specified and directed.

Returning filling in excavated soil including spreading, levelling, watering and well ramming in layers not exc 25 Cm, complete all as specified and directed.

Removing excavated materials (soil) not exc 50 m distance and depositing where directed at a level not exc 1.5 m above the starting point, complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for reuse or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Dismantling unserviceable main switch/DBs incl wooden board and deposit to MES store yard including making good disturbed surface of wall complete all as specified and directed.

Taking down sub main wiring /XLPE cable of any size/capacity complete all as specified and making good disturbed sufaces to match with the existing surface, complete all as specified and directed.

M&L for disconnecting and taking down of ceiling fan/exhaust fan/geyser of any type/capacity and reconnecting and refixing the same after rewiring work, complete all as specified and directed.

M&L for Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface including making good disturbed surface all as specified and directed for the following: - a) One light/ceiling fan/exhaust fan/bell buzzer point controlled by one, one way switch of 5/6 Amps.

b) One 5 Pin, 5/6 amps socket outlet point on independent board, controlled by one, one way 5/6 Amp switch.

c) One 5 Pin, 5/6 amps socket outlet point on same board, controlled by one, one way 5/6 Amp switch.

d) One light point controlled by two, two way switch of 5/6 Amps.

M&L Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 2.5 Sqmm, with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable FRLS of size 2.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface for one socket outlet 15 amp on independent board including making good disturbed surface, complete all as directed and specified.

S&F switch piano flush type 5/6 Amps, 230 volts, single pole, one way, ISI marked, complete all as specified & directed.

S&F switch piano flush type 5/6 Amps, 230 volts, single pole, Two way, ISI marked, complete all as specified & directed.

S&F bell push, flush type, single pole, AC, 240 volts, 5/6 amps, complete all as specified and directed.

Supply and fixing switch socket combination, 5/6 and 15/16 Amps, 230 volt, multi pin, flush type universal, complete all as specified and directed.

Supply and fixing socket outlet, 5/6 Amps, 230 volt, five pin, flush type universal, complete all as specified and directed.

S&F stepped type electronic fan regulator, flush type, 230 volts AC, single pole, humming free, fixed on the existing phenolic laminated sheet, complete all as specified and directed.

S&F ceiling rose surface type PVC/Polycarbonate isolated body, 65x 50mm, 3 terminals, complete all as specified & directed.

S&F of wall mounted LED Tube light fittings, batten type with bipin holders, powder coated steel with & including retrofit 18 watt LED tube, internally prewired, complete all as specified and directed.

S&F of wall mounted LED Tube light fittings, batten type with integrated LED tube, powder coated steel with & including retrofit 11 watt LED tube, internally prewired, complete all as specified and directed.

S&F surface mounted LED down light fitting, 20 watt, polycarbonate body, complete all as specified and directed.

S&F in renewal of LED building security light fitting, 25 watt, pressure die cast aluminium housing with IP 66 deg of protection, complete with & including 0.55 m long street light bracket made of 32 mm bore GI light grade tubing including necessary clamps, nuts, bolts, washers etc, complete all as specified and directed.

S&F PVC/polycarbonate lamp holder, angular/batten type with back plate, ISI marked complete all as specified & directed.

S&F MCB, 6 to 32 Amps, Single Pole, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S&F MCB, 6 to 32 Amps, Single Pole & Neutral, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S & F, MCB TPN 63 Amps, 415 volts, four pole, B-curve, rupturing capacity 16KA conforming to IS-8828-1996, IEC-60898, complete, all as specified & directed by Engineer-in- charge.

S & F factory made MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, IP-43-IK09 protection grade, earth bar and Din rail, 415 Volts TPN with 4 ways, Double door, complete all as specified and directed.

S & F factory made MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, earth bar and Din rail, 240 Volts SPN with 4 ways, Double door, complete all as specified and directed.

S & F factory made MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, earth bar and Din rail, 240 Volts SPN with 8 ways, Double door, complete all as specified and directed. Note for items of MCB DB - (1) The unit rate includes for cutting the brick walls to accommodate DB to make flush to wall. (2) The unit rate includes for making good the disturbed surfaces including finishes to match with the adjoining surface.

S&F SPN enclosure with a two pin and earth plug and socket, complete with one double pole MCB of 20 amps, 230 Volts AC, complete all as specified and directed.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed FRLS multistranded copper conductor cable of size 6 Sqmm LT, 1100 volts grade, drawn through and including 20 mm dia PVC non metallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded FRLS copper conductor cable green colour as earth continuity conductor, complete all as specified & as directed.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed FRLS multistranded copper conductor cable of size 4 Sqmm LT, 1100 volts grade, drawn through and including 20 mm dia PVC non metallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 4 sqmm single core multistranded FRLS copper conductor cable green colour as earth continuity conductor, complete all as specified & as directed. NOTE for items of submain wiring:- Two runs of cable one run of earth wire and one run of PVC non metallic conduit of 20mm dia shall be measured as one run length. Cable required for connection to DBs shall deemed to be included and shall not be measured separately. Earth wire shall run inside the PVC conduit.

S&F PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover of size 100x100 mm and 50 mm deep, complete all as specified and directed.

S&F PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover of size 175x100 mm and 50 mm deep, complete all as specified and directed.

S&F PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover of size 200x150 mm and 50 mm deep, complete all as specified and directed.

S&F PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover of size 250x200 mm and 50 mm deep, complete all as specified and directed.

M&L for Earthing with galvanized steel earth plate electrode of size 600 mm x 600mm x 6.0 mm, buried directly in ground (earth plate not less than 2.25 Mtr below normal ground level) connected to galvanized iron earth wire of 4 dia by means of bolts, nuts, check nuts and washers of galvanized iron including 15 mm bore light grade GI tubing for protection of earth wire, MS sheet metal funnel with wire mesh, watering pipe medium grade 20 mm bore, charcoal or coke and common salt in alternative layer of 15 Cm compacted thickness all around the electrode with concrete earth pit of PCC 1:3:6 type 75 mm thick precast RCC (1:2:4) type B1 pit cover reinfored with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar and necessary excavation, earth work, in soft/loose soil and disposal of spolis to a distance not exc 50 Mtr and necessary connection and testing complete all as shown in electrical plate No. 5 and including dismantling of old u/s earthing complete all as specified and directed. Notes: - (a) Irrespective of whatever is shown in plate No 5 of SSR, earth pit shall be casted in PCC (1:3:6) type C-1 and precast cover of RCC (1:2:4) type B-1 with suitable handle. (b) Item includes the cost of GI pipe for protection of earth wire and earth wire upto 7.5 m. Any variation below or above shall be measured and paid for separately under relevant item of this Sch ‘A’.

S&F metal body propeller type ventilating fans (Exhaust fan), 240 volts AC, 300 mm sweep with louver shutter complete including connecting with and including PVC insulated three core 23/.0076 copper conductor cable, rubber insulated from ceiling rose to exhaust fan motor and writing MES No with black synthetic enamel paint 2.0 cm high complete all as specified and directed.

Supplying, laying, jointing testing and commisioning XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with multistranded aluminum conductors, 1100 Volt grade of cross-sectional area 35 Sqmm, 3.5 core, laid in trenches / ducts / encased in GI pipe / fixed to pole/wall, complete all as specified and directed.

Supplying, laying, jointing testing and commisioning XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with multistranded aluminum conductors, 1100 Volt grade of cross-sectional area 25 Sqmm, 3.5 core, laid in trenches / ducts / encased in GI pipe / fixed to pole/wall, complete all as specified and directed.

Supplying, laying, jointing testing and commisioning XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with multistranded aluminum conductors, 1100 Volt grade of cross-sectional area 6 Sqmm, 2 core, laid in trenches / ducts / encased in GI pipe / fixed to pole/wall, complete all as specified and directed.

M&L dry clean Sand filling in trenches around underground cables for earth cushion, complete all as specified and directed. Note: - Depth of sand shall be measured after punning.

Supplying and laying pulverized fuel Ash-lime bricks (Fly ash bricks - non modular size), laid flat adjoining each other as in protection to UG cables, complete all as specified and directed.

M&L in renewal of 40 mm bore Steel water tubing, light grade, galvanised, with all fitting, laid in trenches/fixed to walls/poles etc as protection to cables, with and including necessary MS clamps, nuts botls, washers etc required for fixing, complete all as specified and directed.

M&L for hard surface/ PCC / road cutting for laying cables, pipe lines etc., cross sectional area exc 300 Sqcm but not exc 500 Sqcm and making good the disturbed surface with PCC 1:2:4 type B1 using 20 mm graded stone aggregate, complete all as specified and directed.

S&F in replacement LED light fitting 36 Watt, 230 Volt AC, recessed mounting mirror optic luminiare with paralite louver complete, suitable for false/grid ceiling, complete with electronic driver, connector block and all accessories, duly prewired, including connecting up with three core twisted flexible copper conductor cable of size 14/.0060, complete all as specified and directed.

S & F of BEE 5 star rated Electric Water heater storage type (Geyser) with glass lined tank for protection against corrosion for longer life of tank and heating element with 4-in-1 multipurpose valve for safety, temperature indicator dial, fire retardant cable Neon indicators for 'Power on' & 'heating' functions supplied and installed complete, capacity 25 litres, after fixing 4 Nos new fasteners of minimum 10 mm dia in wall and tightening with nuts & washers, connecting with and including two Nos 450 mm long SS wire braided flexible connection pipe with CP brass nuts & nylon washers at both ends, complete all as specified & directed.

Supply, installing, commissioning and testing energy efficient BEE 5 star rated split type air conditioner with intelligent remote control, 220Volts AC, nominal capacity 1.5 TR, complete with copper condensing tubing designed for outside ambient temperature (summer 50 degree celcius, monsoon 32 degree celcius), relative humidity 50% to 60 %, number of air changes 3-4 per hour, copper refrigerant piping with insulation (EP foam pipe section) upto 3 metre from indoor unit to outdoor unit with copper power cables upto 4 mtr including supply, fixing/grouting a set of best quality mounting brackets for outdoor unit, complete all as specified and directed.

Supply, installing, testing and commissioning Voltage stablizer for automatic operation, single phase naturally air cooled, indoor type and designed for input voltage of 170-260 volts with out put voltage stablized at 220 volt with accuracy of +/-1.00%, capacity 5.0 KVA, mounted on wall with suitable arrangements, complete all as specified and directed.

Supply, installing, commissioning and testing outdoor type feeder pillar box factory made (CPRI approved manufacturer), structure fabricated from 3.15 mm thick CRCA sheet, compartmentalized design of suitable size with opening from front and back including mild steel channel frame of ISMC 75 at the base of panel only for grouting purpose, and grouted in PCC 1:2:4 type B-1 using 20mm graded stone aggregate. The panel shall be dust & vermin proof by providing good quality gasket on doors removal covers, gland plates etc including all internal connections with 4 Nos heat shrink insulated aluminum bus bar of 400 ampere rating. The sheet metal work of the panel shall have powder coated finish internally and externally. The panel shutter / doors shall be provided with detatchable & flush type hinges including flush cylindrical locks. Provision for cable entry shall be from either side. All joints and connection shall be done by galvanised or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided and complete with the following accessories: -

SHREEKRISHNA INFRASTRUCTURE

L P Singh and Co.

M/S MOHINI ENTERPRISES

TARKESHWAR DASS CONSTRUCTION COMPANY

K B Enterprises

ANNAPURNA ENTERPRISES

M/s Prem Associates

M/S MAMTA CONSTRUCTIONS