Repair to roof treatment in certain bldg and other misc BR items at domestic area and repair to flooring sunken treatment plumbing work in certain bldgs at domestic area under AGE BRII GE AF No 02 Jodhpur

Amount

Taking down existing roof treatment with wire brushing and cleaning of top surface of terrace or cement concrete including dismantling existing old roof treatment, junction of parapet and removing all demolished material upto 5.00 KM as directed by Engineer-in-Charge

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate in roof padding as directed by Engineer-in-Charge.

M&L10 mm thick screed bed with CM 1:4 with water proofing compound @ 3% by weight of cement finish even and smooth surfaces using without extra cement. Water proofing compound shall be measured and paid seperately as directed by Engineer-in-Charge

M&L APP modified membrane minium weighting 3 Kg/Sqm with polyster non woven polyster reinforcement ( weight not less than 150 gms/sqm )shall be laid by torch application method and overlapped by 100 mm in all sides over a coat of Bituminous primer @ 500 ml/sqm as directed by Engr-in-Charge

Supply only integral water proofing compound ISI marked as directed by Engineer-in-Charge

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specially sunkun floor provided for complete all as specified and directed

M&L for plain cement conrete 1:5:10 type E-2 (using 20 mm graded broken bricks aggregate ) as in sunken/foundation and mass concrete complet all as specified and as directed by Engineer-in-Charge

M&L for water proofing treatment of sunken floor of WCs bathroom etc by applying of the following specifiaction:-(i) Cleaning of sunken floor surface with mechanical means i.e wire brush/air blower etc and remove all loose/unsound material dirt dust etc. (ii)Applying cement slurry mixed with acrylic based polymer modified cementious composite compund coating Hydroproof Xtra of FOSROC /Equivalent of Dr Fixit of Pidilite industries Ltd in the ratio 1:2:4 (one part of acrylic polymer : two part of water and four partof cement) (iiii) First layer of cement slurry @0.444 kg /sqm mixed with acrylic based modified cementious composite compund @0.222 litre/sqm and allow it to air dry for 4 hour. (iv) Second layer of cement slurry @0.222 kg /sqm mixed with acrylic based dified cementious composite compound @0.111 litre/sqm and allow it to air dry for 4 hour followed with water curing for 48 hours (v) 200 micron thick polytgen film shall be pasted with help of adhesive over treatment . Note:- Joints of WC/Trap/Soil waste shall be prperly sealed with sealing compund . Testing of all traps and joints and sunken slab shall be done as per IS-1742 before filling and tiling work as directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) and removing from site all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing from site and rubbish off the premises as directed by Engineer-in-Charge

M&L for joint free non skid ceramic tiles, coloured, 7 to 8 mm thick in floors etc. (square/rectangular) area of each tile exc. 0.06 sqm but n. exc. 0.11 sqm, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 as directed by Engineer-in-Charge

M&L for glazed ceramic tiles, coloured, 350x250x7mm/450x350x7mm thick on vertical surfaces such as skirtings, dados and risers to steps etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 on stone masonry surfaces as directed by Engineer-in-Charge.

M&L for light coloured vitrfifed cermaic tiles 10 mm thick area of each tiles not less than 0.36 sqm in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in CM 1;6 as directed by Engineer-in-Charge

All as per item no. 13.00 above but on vertical surfaces such as dados skirting and risers to step set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick renedering in CM 1:4 on stone masonary surfacesas directed by Engineer-in-Charge

Cleaning and removing all scale dirt etc. from water storage tanks and from mouth of circulating pipes etc. and writing the date of cleaning and next due date for cleaning of tank, capacity of tanks exc. 250 liters and not exc. 500 liters complete all as specified and as directed.

Cleaning and removing all scale dirt etc. from water storage tanks and from mouth of circulating pipes etc. and writing the date of cleaning and next due date for cleaning of tank, capacity of tanks exc. 500 liters and not exc. 1000 liters complete all as specified and as directed.

Disconnecting existing tanks of any description exc. 250 ltrs and n.exc. 500 ltrs capacity and removing from site complete all as specified and as directed.

Disconnecting existing tanks of any description exc. 500 ltrs and n.exc. 1000 ltrs capacity and removing from site complete all as specified and as directed.

Disconnecting existing tanks, exc. 250 ltrs and n.exc. 500 ltrs setting aside (or lowering if required) for repairs, cleaning, etc. And hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. Measured separately) complete all as specified and as directed.

Disconnecting existing tanks, exc. 500 ltrs and n.exc. 1000 ltrs setting aside (or lowering if required) for repairs, cleaning, etc. And hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. Measured separately) complete all as specified and as directed.

S&F 500 litres (ISI marked) capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore plastic ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic plastic ball screwed for iron pipe and fixed. (Minimum weight of ball valve - 210 gms)

S&F 1000 litres (ISI marked) capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball brass valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic plastic ball screwed for iron pipe and fixed. (Minimum weight of ball valve - 210 gms)

S&F in repairs 15 mm dia gun metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe.

S&F in repairs 20 mm dia gun metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe.

S&F in repairs 25 mm dia gun metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe.

Taking up or down steel tubing 15mm bore and connections including cleaning for refixing or removing from site.

Taking up or down steel tubing 20mm bore and connections including cleaning for refixing or removing from site.

Taking up or down steel tubing 25mm bore and connections including cleaning for refixing or removing from site.

Refixing old steel tubing 15mm bore and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and directed.

Refixing old steel tubing 20mm bore and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and directed.

Refixing old steel tubing 25mm bore and connections in new or old position (Walls, ceiling, floors, etc.)complete all as specified and directed.

Supply and laying 15mm bore tubes, galvainzed steel, medium grade, with all fittings and fixed complete on walls and ceilings or laid in floors all as specified and directed.

Supply and laying 20mm bore tubes, galvainzed steel, medium grade, with all fittings and fixed complete on walls and ceilings or laid in floors all as specified and directed.

Supply and laying 25mm bore tubes, galvainzed steel, medium grade, with all fittings and fixed complete on walls and ceilings or laid in floors all as specified and directed.

S&F in repairs 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms.)

S&F in repairs 15 mm bore bib taps, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule.

S&F in repairs 15mm bore pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete.

S&F in repairs, 15 mm bore stop valve, fancy type, chromium plated with long shank and cup , screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions.

S&F in repair brass chromium plated shower rose of 125 mm size with swivel joint including fixing to steel pipe or union.

S&F in repair sink made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm, bowl size 410mm x 330mm x 160mm and PVC waste pipe of 32mm bore and of suitable length, complete all as specified.

S&F in repair sink with drainage board made of stainless steel 1.00mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm, bowl size 410mm x 330 mm x 160 mm and PVC waste pipe of 32mm bore and of suitable length, complete all as specified.

S&F in repairs vitreous china wash basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, brass chromium plated perforated waste coupling/ fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32mm bore and of suitable length, complete all as specified.

S&F in repairs, EWC vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device fixed complete all as specified.

S&F in repairs vitreous china squatting pan, ‘Orissa’ pattern, size 580 mm x 440 mm, white with integral foot rests, including PVC 'P' trap, embedded and set in PCC 1:5:10 type E-2 and making good to floor including removing rubbish.

S&F in repairs PVC valveless, syphonic action type, flushing cistern, low level, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets.

S&F in repairs 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete type B1(1:2:4).

S&F in repairs 75mm PVC (SWR) Nahani trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete type B1(1:2:4).

S&F in repairs PVC(SWR) branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches for 75 mm bore pipe.

S&F in repairs PVC(SWR) branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches for 100 mm bore pipe.

S&F in repairs 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F in repairs 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F in repairs 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed.

S&F in repairs 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed.

M&L in repair for vitrous china urinal flat back bowl type complete including including providing and fixing plug size 465X355X265 mm white (minimum) with grating and union for discharge pipe All as spfd

S&F in repairs PVC connection 15 mm size with PTMT nuts of length 450 mm.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm each or as directed by Engineer-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but not exc 4 sqm each as directed by Engineer-in-Charge.

Dismantling of cast iron or reinforced concrete drain pipe, jointed in cement mortar and taking out of trenches or in vertical positions of internal dia 100 mm & less all as directed by Engineer-in-Charge.

M&L for preparation of old plastered or un-plastered surfaces of walls and applying two coats of oil emulsion distemper white or tinted over a layer of wall putty including removing existing nails, if any, any Nos and filling the disturbed surface/holes complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old decorated plastered or un-plastered surfaces of walls applying one coat of cement base paint, white or tinted, all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new plastered or un-plastered surfaces of walls and applying two coats of oil emulsion distemper white or tinted including removing existing nails, if any, any Nos and filling the disturbed surface/holes making smooth surface as directed by Engineer-in-Charge.

M&L for preparation of new decorated plastered or un-plastered surfaces of walls applying two coats of cement base paint, white or tinted, all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new decorated plastered or un-plastered surfaces of walls applying two coats of cement base paint, white or tinted, all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new wooden surfaces of any description, over 10 cm in width or girth, not otherwise described priming coat with pink primer and applying two coats of synthetic enamel paint as directed by Engineer-in-Charge.

M&L powder coated anodised aluminium frame for doors, windows, louver type ventilators including rotating type fixing arrangement for fixing of louver glass joining cleat for fixing etc complete and all as specified & directed.

S&F 35 mm thick factory made , second class hard wood Palin framed panelled shutter (two panel with lock rail and panel of 9 mm BWP commercials ply or 12 mm veneered particle board with commercial veneering on both face .The size of rail and stile as per directed.

S&F 35 mm thick factory made , second class hard wood and skeleton shutters open rebated and prepared to receive glass gauze etc (without sash bars ) edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass etc sizes complete all as specified & directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, as directed by Engineer-in-Charge.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck

S&F 200 mm long aluminium, anodized, barrel tower bolts of extruded section and fixed as directed by Engineer-in-Charge.

S&F 300 mm long aluminium alloy anodized sliding door bolt with hasp staple (bolt type ) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts and sliding bolts of extruded sections or cast aluminium alloy as directed by Engineer-in-Charge.

S&F for 100 mm long butt hinges, medium weight stainless steel as directed by Engineer-in-Charge.

S&F aluminium handles, cast type, anodized, of size 150mm as directed by Engineer-in-Charge.

S&F galvanised mild steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks or galvanised wire staples as directed by Engineer-in-Charge.

Welding in repairs exc 2.5 cm & n exc 5 cm in length & thickness of metal n.exc 6 mm all as specified and directed by Engr-in-charge

S&F in repair galvanised mild steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks or galvanised wire staples as directed by Engineer-in-Charge.

S&F in repair Stainless steel curtain rod with and including fancy type SS fixing brackets, end brackets etc complete all as directed by Engr-in-charge.

M&L for hacking out old broken glass (any thickness, size, quality or description) from metal frame glazed with putty including punching or drilling out old glazing pin/spring, clips and providing new ones as directed by Engineer-in-Charge.

S&F sheet glass 3 mm thick, ordinary quality and glazing with oil putty or wooden beads supplied with shutters in square n.exc. 0.5 sqm in each pane as directed by Engineer-in-Charge.

S&F figured glass pin head type 4 mm thick, fixed as louvers in ventilators supplied square n. exc. 0.5 sqm in each pane as directed by Engineer-in-Charge.

S&F pressed steel frames for doors with one or more rebates including necessary fixing lugs hinges lock strike plate etc for 125 X60 mm complete & fixing also as specified supplied and fixed and as directed by Engineer-in-Charge.

S&F in repair CP tubular towel rail, 20 mm dia, D type, 60 cm long between flanges and all as specified and directed by Engineer-in-Charge.

S&F in repair CP grating 100 mm dia all as specified and as directed.

S&F in repairs stainless steel plate rack 0.56mm thick of standard pattern of size 750x600x250 mm complete as directed by Engineer-in-Charge.

S&F Brass handles, cast type polished bright of size 75 mm complete all as specified and directed.

S&F Brass handles, cast type polished bright of size 75 mm complete all as specified and directed.

S&F ball catches with 8 mm dia steel ball and brass body and striking plate including letting in and fixed as directed by Engineer-in-Charge.

S&F plain white 18mm thick UPVC (WPC) sheet/board of required size in cupboards and in similar works including brackets/bolts for fixing. The panels shall be fabricated using adhesive and screws where required .All the edges shall be covered with 2 mm thick

S&F cupboard shutters of required sizes at site made out of 18 mm thick one side decorative teak face finish consisting of 18mm thick UPVC (WPC) sheet/board including all necessary fittings and fixtures like handles, hinges, locking devices, magnetic cat

S&F in repair 15 mm bore stop valve, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butter fly handle, and screwed both ends for iron pipe or for unions as directed by Engineer-in-Charge.

S&F in repairs vitreous china wash basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, brass chromium plated perforated waste coupling/ fittings 32 mm dia with long screwed shanks and

BLANK

S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long all as directed by Engr-in-charge.

S&F in repair 500 litres capacity (ISI marked) rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore plastic ball valves high pressure

Cutting chases stone concrete blocks pinning in making good to facing where required and pointing in CM 1:3 to ends or edge of landing steps cills sunshades shelves lintels etc and cutting chases for concealed water tubing making good not exceeding 10 cm

S&F PVC (SWR) gully traps of size 125/110 mm, setting and jointing with solvent cement and complete and as directed by Engineer-in-Charge.

S&F in repair for PVC (SWR), junction single, (Single T) with door 110 mm dia equal or unequal as directed by Engineer-in-Charge.

All as per item No. 98.00 here-in-above, but 75 mm dia as directed by Engineer-in-Charge.

S&F in repair for PVC (SWR) door bends 110 mm dia as directed by Engineer-in-Charge.

All as per item No.100.00 here-in-above, but 75 mm dia as directed by Engineer-in-Charge.

S&F in repair for PVC (SWR) Cowl 110 mm dia as directed by Engineer-in-Charge.

M&L for water proofing treatment of sunken floor of WCs bathroom etc by applying of the following specification:-(i) Cleaning of sunken floor surface with mechanical means i.e wire brush/air blower etc and remove all loose/unsound material dirt dust etc. (ii)Applying cement slurry mixed with acrylic based polymer modified cementious composite compound coating Hydroproof Xtra of FOSROC /Equivalent of Dr Fixit of Pidilite industries Ltd in the ratio 1:2:4 (one part of acrylic polymer : two part of water and four part of cement) (iiii) First layer of cement slurry @0.444 kg /sqm mixed with acrylic based modified cementious composite compound @0.222 litre/sqm and allow it to air dry for 4 hour. (iv) Second layer of cement slurry @0.222 kg /sqm mixed with acrylic based dified cementious composite compound @0.111 litre/sqm and allow it to air dry for 4 hour followed with water curing for 48 hours (v) 200 micron thick polythen film shall be pasted with help of adhesive over treatment . Note:- Joints of WC/Trap/Soil waste shall be properly sealed with sealing compound . Testing of all traps and joints and sunken slab shall be done as per IS-1742 before filling and tiling work as directed by Engineer-in-Charge.

Supply and laying 32 mm bore tubes, galvainzed steel, medium grade, with all fittings and fixed complete on walls and ceilings or laid in floors all as specified and directed.

M&L for machine cut kota stone slab flooring 20 -25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 15 mm screed bed or bedding layer etc complete all as specified & directed.

M&L for kota-stone slab 15 mm thick in riser of steps skirting dado skirting and risers to step set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in CM 1:4 on stone masonry surface etc complete all as specified & directed.

M&L for granite (of any type ) tiles 20 mm thick machine cut in skirting /dado over and including 10 mm thick rendering in CM 1:4 on stone masonry surfaces jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the surface etc complete all as specified & directed.

M&L for rendering 15 mm thick in CM 1:4 on stone masonry surfaces finished even and smooth without using extra cement as directed by Engineer-in-Charge.

M&L for rendering 15 mm thick in CM 1:6 on stone masonry surfaces finished even and smooth without using extra cement as directed by Engineer-in-Charge.

M&L 75 mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in plinth protection finished surface even and fair without using extra cement all as specified and as directed by Engineer-in-Charge.

M&L for cement concrete type-B-2, 1:3:6, 75 mm thick complete all as specified & directed.

M&L for providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour design & pattern as in footpath parks lawns drive ways or light traffic parking etc. of required strength thickness & size etc complete all as specified & directed.

S&F MS powder coated louvers with including arrangement of fixing glass pinhead as per size & louvers ventilators (Glass shall be measured separately ) complete all as specified and as directed.

M&L for providing and injecting chemical emulsion for post construction anti termite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 ltr per sqm of the vertical surface of the sub structure to a depth etc complte all as specified & directed.

M/s RKG CONSTRUCTIONS

psj build solutions and company

suryabuildtechdevlopers

Bansal Enterprises

M/S JAGDAMBA ENTERPRISES