REMAINING WORKS OF I.S.B.T., TANAKPUR, DISTRICT CHAMPAWAT

Amount

1.0 CARRIAGE OF MATERIALS By Mechanical Transport including loading,unloading and stacking EARTH 1 Km with in th site.

1.0 CARRIAGE OF MATERIALS By Mechanical Transport including loading,unloading and stacking EARTH 2 Km with in th site.

1.0 CARRIAGE OF MATERIALS Note:- These rates are inclusive of GST on work contract, Contractor's profit and over heads, Cess etc. By Mechanical Transport including loading,unloading and stackingBeyond Beyond Beyond 5km upto 10 km per km 326.68+(23.16*5=115.80)=442.48 D.S.R.1.1.2

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Diluting and injecting chemical emulsion (chlorpyriphos/Lindane E.C 20% with 1% concentration) at the rate of one litre per hole at 300 mm c/c to all the horizontal and vertical surface of the excavation made for the foundation of the building, soil under floor,apron, back fill material and along all the faces of the walls for PRE-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) as per IS:6313 Part-II. (Plinth area of building shall be measurd for payment.)

Construction of Embankment with Material Obtained from Borrow Pits Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 S.O.R. MORD 3-4

Concrete with cement, coarse sand and 40 mm gauge stone ballast in proportion 1:4:8 in foundations and floors including supply of all material, labour and T&P etc. required for proper completion of the work. as per drawings and technical specifications Clause 802, 803, 1202 & 1203 S.O.R. MISC 2-2

Granular Sub-base with Well Graded Material (Table 400.1) 4-1-A By Mix in Place Method Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401.For Grading III Material S.O.R. MORD 4-1-A-3

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size).

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mmnominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering,shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more

Centring and shuttering including strutting,ropping etc. and removal of form forFoundations, footings, bases of columns, etc. for mass concrete.

Centring and shuttering including strutting,ropping etc. and removal of form forWalls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centring and shuttering including strutting,ropping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts.

Centring and shuttering including strutting,ropping etc. and removal of form forLintels, beams, plinth beams, girders, bressumers and cantilevers.

Centring and shuttering including strutting,ropping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Centring and shuttering including strutting,ropping etc. and removal of form for Sheleves(Cast In Situ)

Centring and shuttering including strutting,ropping etc. and removal of form for Edges of slabs and breaks in floors and walls Under 20 cm wide

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured).Suspended floors, roofs, landings, beams and balconies (Plan area to be measured)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)

Extra for providing and placing in position 2 Nos 6 mm dia. M.S. bars at every third course of half brick masonry.

Providing and fixing 18mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut for kitchen platforms, vanity counters ,window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse Granite of any colour and shadeArea of slab over 0.50 sqm.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing wire gauge shutters using galvanized M.S. Wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size Second class teak wood

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125 mm

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete300x16 mm

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete250x16 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete250x10 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete150X10 MM

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Sal wood

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Single rubber stopper

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :

Providing and fixing bright finished brass handles with screws etc. complete: 125 mm

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing fly proof galvanised M.S wire gauze to windows and clerestory windows using galvanised M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm. With 12 mm mild steel U beading.

roviding and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :4.0 mm thick glass panes

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, priming coat of approved steel primer, but excluding the cost of other fittings,glass panes complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Extra for providing mechanical device chain and crank operation for operating rolling shutters.Exceeding 16.80 sqm in area

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

Providing and laying pressed clay tiles (as per approved pattern 20 mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound, laid over a bed of 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx400micron, finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement rounding the edge sand making and finishing the outlet complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Coupler110 mm

Bend 87.5 degree 110 mm bend

Shoe (Plain)110 mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including 110 mm

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand)

12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 20 mm cement plaster

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water tinnable priming coat with cement primer

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

French spirit polishing :Two or more coats on new works including a coat ofwood filler

Polishing on wood work with ready mixed wax polish of approved brand and manufacture : New work

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres. D.S.R.16.1

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). D.S.R. 16.75

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete.

Extra for providing and mixing hardening compound of approved quality as per manufacturer’s specification in cement concrete D.S.R.16.44

Providing and applying 2.5 mm thick road marking strips (retroreflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications. D.S.R.16.62

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). D.S.R.16.69

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. D.S.R.16.68

Providing and fixing Glow studs of size 100x20 mm made of heavy duty body shall be moulded ASA (Acrylic styrene Acryloretrite ) or HIP (High impact polystyrene) or ABS having electronically welded micro- prismatic lens with abrasion resistant coating as approved by Engineer in charge. The glow stud shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35 (+/-5) degress to base .The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge. D.S.R.16.50

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mmheight including rounding of junctions of walls and slabs.(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. “All above operations to be done in order and as directed and specified by the Engineer-in-Charge”: With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. Sunken

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

For horizontal surface one coat @1.10 kg per sqm.

For vertical surface two coats @ 0.70 kg per sqm

Replacement of M.S. foot rests in manholes including dismantling concrete blocks and fixing with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size): With 20x20 mm square bar

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 Rectangular shape 600x450 mm internal dimensions

Supply & fixing of WPC board work for elevation complete in all respects including all labor & installation.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, with Manual Piston-Type Water Closet Flush Valve for wall-hung 1-1/2" top spud bowls including cover tube and wall flange and overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever requiredW.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a pair 15 mm C.P. brass pillar tap

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge

Providing and fixing brass stop cock of approved quality :15 mm nominal bore

Providing and fixing 600 x 450mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete in all respect.

Providing and fixing uplasticised PVC connection pipe with brass unions :15 mm nominal bore

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing toilet paper holder.Vitreous china

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :510x1040 mm bowl depth 250 mm

Providing and Fixing, testing & commissioning of ABS Health Faucet (complete with hook and flexible tube min. Length 1.0 m) as required complete in all respect.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115 mm nominal bore

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately).

Supplying and stacking of Good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment)only in Lawn area

Carriage of Material by Mechanical Transport including loading, Unloading and stacking (upto 5 km lead)

Supplying and spreading of sand in lawn area, including watering, and dressing complete.

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately)

Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area.(two application) i/c cost of chemical)and as per direction of officer-in-charge.and as per direction of officer-in-charge

Providing and Displaying Bird of paradise well developed with fresh & healthy 90 to 120 cm ht in 30 cm Earthen Pot/ Plastic Pot as per direction of the officer-in-charge.

Providing and Displaying Cycus revoluta specimen , having 45 to 50 fresh and healthy, leaves having 30cm to 35cm circumfrance of base stem well developed in 40 cm challi, as per direction of the officer-in-charge.

Providing and Displaying Golden Bottle brush Topiary well developed with fresh & healthy foliage 5 to 6 big ball 115 to 180 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Topiary of Casuarina fresh & healthy having 5 to 6 specific shape and size ball well developed 195 to 210 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Hamelia patens of height 60-75 cm. with 6-8 branches in poly bags of size 25 cm as per direction of the officer-in-charge

Providing and stacking of Plumbego capensis well developed with fresh and healthy 30 to 45 cm ht., with bloom in 20 cm Earthen Pot/Plastic Pot as per direction of the officer-in-charge

Providing and stacking of Nerium oleander (kaner) dwarf of height 30-40 cm. in earthen pot of size 20 cm as per direction of the officer-in-charge

Providing and stacking of Asparagus marrie, well developed 15 to 20 leaves, full of branches and foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Asparagus sprengeri of height 30 cm to 45 cm, full of leafy branches in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge..

Providing and stacking of Chlorophytum-variegated, full of leafy suckers in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Cuphea chinensis of ht. 20-30 cm full of branches and healthy foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge

Providing and stacking of Daniella variegated, with 3 to 4 variegated leaves in 20 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge

Providing and stacking of Iresine herbstii, of height 25-30 cm., full of branches well developed in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge

Providing and stacking of Ophiopogon jaburan ( variegated ),full of variegated leaves in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge

Providing and stacking of Schefflera green, having 3 to 4 branch, ht. 30 to 45 cm well developed with fresh & healthy in 20 cm size of Earthen Pot/ Plastic Pot as per direction of the officer-in-charge

Providing and stacking of Largerstroemia indica of height 90-105 cm. multibranched in poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and Displaying Cyprus Golden Conical Shape 150 to 165 cm ht., with fresh and healthy Golden colour foliage in 35cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Bamboo Buddha valley with fresh & healthy 3 to 4 suckers having 75 to 90 cm ht. in 25 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge

Providing and stacking of Plumbego capensis well developed with fresh and healthy 30 to 45 cm ht., with bloom in 20 cm Earthen Pot/Plastic Pot as per direction of the officer-in-charge.

Providing and stacking of Hamelia patens of height 90-105 cm. bushy in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Murraya exotica of height 45-60 cm. in poly bags of size 15 cm as per direction of the officer-in-charge.

Providing and stacking of Nerium oleander (kaner) dwarf of height 30-40 cm. in earthen pot of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of plant Mogra of height 25 to 30 cm., 2 to 3 branch in earthen pots of size 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Tree

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Shrubs

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Hedge

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) Holes 60 cm dia, and 60 cm deep (for Trees)

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) Holes 45 cm dia, and 45 cm deep (For Shrubs)

Topiary cutting/shapping of plant removing of cut materials, cleaning, hoeing of plants complete design hoeing of trees (Topiary) watering manure etc.(excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge. Height of Topiary above 120 cm

Cutting of designer hedge/edge removing of cut materials, cleaning, hoeing of hedge/edge bed watering manure and applying insecticides and fungicides etc.(excluding the cost of material which shall be supplied by the Per Sqm department) and as per direction of officer in charg

Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, edge, flower beds, foliages, creepers etc. including hoeing,weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide will be provided by the Department & lawn mover and brush cutter with fuel and other T & P material/articles shall be provided by the contractor.) and as per direction of officer in charge.Total qty for 24 Months ( 02 Years) (13119.89 x 24 Months = 314877.36 Sqm )

Providing and mixing Vermicompost For Lawn and flower Beds @ 5 kg Per sqm in Lawn area and 8 Kg in Bed area Bed rea

Providing and stacking of Spider Lillies, of height 25-30 cm., full of branches well developed in Poly Bag as per direction of the officer-in-charge

Providing and stacking of Pennisetum Setaceum Rubram , of height 25-30 cm., full of branches well developed in Poly Bag as per direction of the officer-in-charge

Providing and stacking of Ruellia Tuberosa, of height 25-30 cm., full of branches well developed in Poly Bag as per direction of the officer-in-charge

Providing and stacking of Largestomia Black of height 60-75 cm. Multi branches bushy in poly bags as per direction of the officer-in-charge

Providing and stacking of Podocarpus Macrophylla of height 270-300 cm. Multi branches well shaped bushy in big poly bags as per direction of the officer-in-charge

Providing and stacking of Agathus Roubusta of height 600-630 cm. Multi branches well shaped bushy in big poly bags as per direction of the officer-in-charge

Providing and stacking of Calestemon Lanceolatus of height 240-300 cm. Multi branches well shaped bushy in big poly bags as per direction of the officer-in-charge

Providing and stacking of Washiongtonia Fillifera of height 150-180 cm. Stem height with 6 to 7 leaves well shaped bushy in big poly bags as per direction of the officer-in-charge

Providing and stacking of Date Palm of height 150-180 cm. Stem height with 7 to 8 leaves in good shape in big poly bags as per direction of the officer-in-charge

Providing and stacking of Foxtail Palm of height 3600-3900 cm. Healthy plant in good shape in big poly bags as per direction of the officer-in-charge

Providing and stacking of Mimusops Elengii of height 270 cm to 300 cm. height in good shape in big poly bags as per direction of the officer-in-charge

Topiary Ficus Microcarpa ( Imported) in Bonsai Shape height 180 cm to 210 cm in Good Shape and Size as per direction of officer in charge

Bougainvellia Ball 1 meter Dia in different Colours in Good Shape and proper Size as per direction of officer in charge

Providing and stacking of Stand Kamini, of height 25-30 cm., full of branches well developed in Poly Bag as per direction of the officer-in-charge

Providing and stacking of Buxus, of height 25-30 cm., full of branches well developed in Poly Bag as per direction of the officer-in-charge

Providing and stacking of Bismarkia Nobillis 150 cm to 180 Cm well developed in big size Poly Bag as per direction of the officer-in-charge

Providing and stacking of Spiral juniper of height 150-180 cm. Multi branches well shaped bushy in big poly bags as per direction of the officer-in-charge

Providing and Displaying Leucophyllum Fruitesence 25 to 30 cm well developed in Poly bag, as per direction of the officer-in-charge

Providing and Displaying Loropattalum 20 to 25 cm well developed in Poly bag, as per direction of the officer-in-charge

Providing and stacking well developed full bloomed Seasonal Flowers in Poly Bags

Material used for proper maintenance during Maintenance period of 02 years( Good Earth for Top Dressing, Manureing Thrice in a year, Fertilizers Thrice in a year, Insecticide & Pesticide where and when required ) as per direction of officer in Charge

Irrigation System as per site condition or as per direction of officer in Charge

Providing, Fixing, testing and commissioning of shower including necessary wall chases and making good. With Single lever wall mixer with spout, adjustable OH shower with arm and wall flange complete with wall flange diverter assembly with Non-return Valves.

Providing and fixing stainless steel satin finish (SS 304) towel rail with plastic rawl plugs and SS screws including cutting and making good the walls wherever required.

Providing and Fixing, testing & commissioning of position storage type automatic electric water heater pressure/ non pressure type thermostratically controlled, single phase, vertical wall mounted of approved make ( to the approval of Engineer-in-charge) with thermostats, inner container of stainless steel complete with 1 Mtr three core flexible cord with plug, non return valve and pressure release valve complete including fixing and testing complete in all respect.25 litres capacity water heater

Providing, fixing and jointing UV stabilized SWR (Type - B) pipes conforming to IS:13592 including all fittings such as bends, clamps, tees, cowls, clean out plugs, offsets, Y-tees, tees, door fittings, clips, clamps, stays etc. conforming to IS-14735, including jointing with rubber gasket fixing in sunk areas, Fixing at wall / ceiling level supported by steel clamps & hangers etc. including Cutting, chases/ holes in floors / walls / slab and making good the same after pipe have been duly laid and testing complete in all respects.75 OD (Sewerage & Drainage)

Providing, fixing and jointing UV stabilized SWR (Type - B) pipes conforming to IS:13592 including all fittings such as bends, clamps, tees, cowls, clean out plugs, offsets, Y-tees, tees, door fittings, clips, clamps, stays etc. conforming to IS-14735, including jointing with rubber gasket fixing in sunk areas, Fixing at wall / ceiling level supported by steel clamps & hangers etc. including Cutting, chases/ holes in floors / walls / slab and making good the same after pipe have been duly laid and testing complete in all respects.110 OD (Sewerage & Drainage)

Providing, fixing and jointing uPVC pipes conforming to IS:4985 including all fittings such as bends, clamps, tees,, offsets, Y-tees, tees, clips, clamps, stays etc. conforming to IS-14735, including jointing with rubber gasket fixing in sunk areas, Fixing at wall / ceiling level supported by steel clamps & hangers etc. including Cutting, chases/ holes in floors / walls / slab and making good the same after pipe have been duly laid and testing complete in all respects.40 mm OD

Providing, fixing and jointing uPVC pipes conforming to IS:4985 including all fittings such as bends, clamps, tees,, offsets, Y-tees, tees, clips, clamps, stays etc. conforming to IS-14735, including jointing with rubber gasket fixing in sunk areas, Fixing at wall / ceiling level supported by steel clamps & hangers etc. including Cutting, chases/ holes in floors / walls / slab and making good the same after pipe have been duly laid and testing complete in all respects.50 mm OD

Providing and fixing in position uPVC Multi inlet trap / P trap conforming to IS:13592 including providing necessary steel support and as per Specification. Making proper connection cutting chase / hole in floors / slabs and bringing the same in proper condition and shape after placing the trap in right position complete as required. The trap shall be set in cement concrete mix 1:2:4 complete as required.

Providing, fixing and jointing UV stabilized uPVC rain water pipes conforming to IS:4985 (working pressure 6 kg/sqcm.) including all fittings such as bends, clamps, tees, cowls, clean out plugs etc including Fixing at wall / ceiling level supported by steel clamps & hangers etc. including Cutting, chases/holes in floors / walls / slab and making good the same after pipe have been duly laid and testing complete in all respects.(I) Single socketed pipes75 mm diameter

Providing, fixing and jointing UV stabilized uPVC rain water pipes conforming to IS:4985 (working pressure 6 kg/sqcm.) including all fittings such as bends, clamps, tees, cowls, clean out plugs etc including Fixing at wall / ceiling level supported by steel clamps & hangers etc. including Cutting, chases/holes in floors / walls / slab and making good the same after pipe have been duly laid and testing complete in all respects.(I) Single socketed pipes110 mm diameter

Providing, fixing, testing & commissioning of 110mm x 63mm uPVC Reducing Elbow for floor drain point and coupler cutting chases, the floor / slab, repairs complete as required and connection to upvc waste pipe.

Providing and fixing Heavy Class SS grating with of approved design including setting in floor with cement motor to match with floor finish as per architect requirement .

Providing and fixing Heavy Class SS grating with Cockroach proof SS strainer of approved design including setting in floor with cement motor to match with floor finish as per architect requirement suitable for waster and FT

Providing & fixing cast brass clean out plug with suitable insert keys for opening in: brass cap, male threaded joint with G.I. socket lead caulked to pipe/fitting of H.C.I, pipe with Drip seal joints as required complete in all respects.100 mm

Providing, installation, jointing and testing of PVC Floor clean out Plug made out of upvc bend, Pvc pipe piece , threaded Pvc socket(FTA), with minimum 100mm bronze threaded cap, suitable insert keys for opening including making joint to PVC main line as required comleter in all respect.100 mm dia.

Providing and fixing EXTENSION PIECE for 100 mm dia floor trap formed out of main pipe (Type A) with multiple side inlets, suitable for various dia pipes, side connections, including all fixtures and fittings as per site conditions and as per standard details and water tight sealing of joints and area surrounding the grating and as directed.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing Chlorinated polyvinyl chloride (CPVC) pipes having thermal stability for water supply including all CPVC plain & brass Threaded fittings i/c fixing the pipe with clamp at 1.00 m spacing. This includes jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge (concealed work including cutting chase and making good the walls etc). 15 mm dia nominal bore

Providing and fixing Chlorinated polyvinyl chloride (CPVC) pipes having thermal stability for water supply including all CPVC plain & brass Threaded fittings i/c fixing the pipe with clamp at 1.00 m spacing. This includes jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge (concealed work including cutting chase and making good the walls etc). 20 mm dia nominal bore

Providing and fixing Chlorinated polyvinyl chloride (CPVC) pipes having thermal stability for water supply including all CPVC plain & brass Threaded fittings i/c fixing the pipe with clamp at 1.00 m spacing. This includes jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge (concealed work including cutting chase and making good the walls etc). 25 mm dia nominal bore

Providing and fixing Chlorinated polyvinyl chloride (CPVC)-SDR-11 pipes having thermal stability for water supply including all CPVC plain & brass Threaded fittings including fixing the pipe with clamp at 1.00 m spacing. This includes jointing of pipes & fitting with one step CPVC solvent cement and testing of joing complete as per direction of engineer in charge (Internal work - exposed on wall ) 25 mm dia nominal bore

Providing and fixing Chlorinated polyvinyl chloride (CPVC)-SDR-11 pipes having thermal stability for water supply including all CPVC plain & brass Threaded fittings including fixing the pipe with clamp at 1.00 m spacing. This includes jointing of pipes & fitting with one step CPVC solvent cement and testing of joing complete as per direction of engineer in charge (Internal work - exposed on wall ) 32 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etcInternal work - Exposed on wall / Terrace25 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etcInternal work - Exposed on wall / Terrace 32 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etcInternal work - Exposed on wall / Terrace 40 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etcInternal work - Exposed on wall / Terrace 50 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etcInternal work - Exposed on wall / Terrace 50 mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 15 mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 20 mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 25 mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 32 mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 40 mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 50 mm dia nominal bore

Providing & fixing closed cell thermal insulation tubes 6mm thick to hot water pipe and fittings. Over 15 mm dia. Pipe

Providing & fixing full way lever operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not less than 10 Kg / sqcm with threaded / flanged joints complete with nuts, bolts, gaskets, washers etc.20 mm dia.

Providing & fixing full way lever operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not less than 10 Kg / sqcm with threaded / flanged joints complete with nuts, bolts, gaskets, washers etc.25 mm dia.

Providing & fixing full way lever operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not less than 10 Kg / sqcm with threaded / flanged joints complete with nuts, bolts, gaskets, washers etc.32 mm dia.

Providing & fixing full way lever operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not less than 10 Kg / sqcm with threaded / flanged joints complete with nuts, bolts, gaskets, washers etc. 40 mm dia.

Providing ,fixing, testing and commissioning of IP 67 (Weather Proof /Aluminum casing with positioner to indicate the valve position with key type manual overdrive) Motorized Butterfly valve / Ball valve of following dia with limit switch arrangement for filling of over head water tank complete with high and low level float type sensors to control the valve .The sensors shall be installed in over head tanks. The sensors will close the valve when water level is high in over head tank and open the valve when over head water tank level is low. The system should be complete in all respects with control panel indicating the position of valve i.e. open /closed with pressure switches at pump discharge, accessories like wiring / conduting / flanges, nut bolts etc.NOTE :- All the control switchgears, connections, wiring, integration etc. should be included in the quote. No additional payment shall be charge for any work against this item.40 mm dia.

Providing ,fixing, testing and commissioning of IP 67 (Weather Proof /Aluminum casing with positioner to indicate the valve position with key type manual overdrive) Motorized Butterfly valve / Ball valve of following dia with limit switch arrangement for filling of over head water tank complete with high and low level float type sensors to control the valve .The sensors shall be installed in over head tanks. The sensors will close the valve when water level is high in over head tank and open the valve when over head water tank level is low. The system should be complete in all respects with control panel indicating the position of valve i.e. open /closed with pressure switches at pump discharge, accessories like wiring / conduting / flanges, nut bolts etc.NOTE :- All the control switchgears, connections, wiring, integration etc. should be included in the quote. No additional payment shall be charge for any work against this item.32 mm dia.

Providing ,fixing, testing and commissioning butterfly valve of PN 1.6 rating with bronze / gunmetal seat duly ISI marked complete with nuts ,bolts,washers ,gaskets conforming IS 13095 of following size as required.50 mm dia.

Providing ,fixing, testing and commissioning butterfly valve of PN 1.6 rating with bronze / gunmetal seat duly ISI marked complete with nuts ,bolts,washers ,gaskets conforming IS 13095 of following size as required.65 mm dia.

455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. All types of soil 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.200 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs,conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100% polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia

Constructing DESILTING CHAMBER of inside size 2000 x 1200 x 1200 mm in brick work of class 75 with cement mortar 1:4 (1cement:4 coarse sand), inside plastering 12 mm thick with cement mortar 1:4 with floating coat of neat cement including baffle wall as per detail . RCC top slab 150mm thick with 1:2:4 all complete as per standard design and direction of enginner in charge.Total Carried to Summary

Supplying, installation, testing and commissioning of electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required. Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520.(Common For Sprinkler & Hydrant System) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered with anti vibration pads.2850 lpm at 88 m Head.

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following,complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.2850 lpm at 88 m Head.

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.180 lpm at 88 m Head

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520.Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for nclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.Suitable cement concrete foundation duly plastered and with anti vibration pads.900 lpm at 35 m Head.

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520.Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for nclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.Suitable cement concrete foundation duly plastered and with anti vibration pads.450 lpm at 35 m Head.

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Fabricating, Supplying, Installation, Testing and Commissioning Air Vessel of continuous welded construction with flanged discharge header in pump house fabricated out of 10 mm thick dished ends and 8 mm thick MS sheet, Air Release Valve, complete with drain arrangement with 25 mm dia gun metal wheel valve complete with all accessories etc. as required of the following sizes:2 Meter high and 450 mm dia suitable to operate Jockey Pump, Main Fire Pump & Diesel Engine Driven Fire Pump.

Providing and fixing of pressure switches in MS pipe line including connection extra as required.

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.250 mm dia

Supplying, fixing, testing and commissioning of double flanged sluice valve of PN 1.6 rating with non rising spindle ,bronze/ gun metal seat,ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 780 of following sizes as required.250 mm dia

Supplying, fixing, testing and commissioning of double flanged sluice valve of PN 1.6 rating with non rising spindle ,bronze/ gun metal seat,ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 780 of following sizes as required.200 mm dia

Supplying, fixing, testing and commissioning of double flanged sluice valve of PN 1.6 rating with non rising spindle ,bronze/ gun metal seat,ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 780 of following sizes as required.150 mm dia

Supplying, fixing, testing and commissioning of double flanged sluice valve of PN 1.6 rating with non rising spindle ,bronze/ gun metal seat,ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 780 of following sizes as required.80 mm dia

Supplying, fixing, testing and commissioning of Butterfly valves PN 16 with bronze / gunmetal sheet duly ISI maked complete with nuts, bolts, washers, gasket conforming to IS 13095 of following sizes as required:50 mm dia

Supplying, fixing, testing and commissioning of NON - RETURN VALVE of following sizes conforming to IS 5312 complete with rubber gasket, GI bolts, nuts, washer etc as reuired 200 mm dia

Supplying, fixing, testing and commissioning of NON - RETURN VALVE of following sizes conforming to IS 5312 complete with rubber gasket, GI bolts, nuts, washer etc as reuired 150 mm dia

Supplying, fixing, testing and commissioning of NON - RETURN VALVE of following sizes conforming to IS 5312 complete with rubber gasket, GI bolts, nuts, washer etc as reuired 100 mm dia

Supplying, fixing, testing and commissioning of NON - RETURN VALVE of following sizes conforming to IS 5312 complete with rubber gasket, GI bolts, nuts, washer etc as reuired 80 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :150 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :100 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :80 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required65 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required50 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required40 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required32 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required25 mm dia

Supplying, fixing, testing and commissioning of Butterfly valves PN 16 with bronze / gunmetal sheet duly ISI maked complete with nuts, bolts, washers, gasket conforming to IS 13095 of following sizes as required:150 mm dia

Supplying, fixing, testing and commissioning of Butterfly valves PN 16 with bronze / gunmetal sheet duly ISI maked complete with nuts, bolts, washers, gasket conforming to IS 13095 of following sizes as required:80 mm dia

Supplying, fixing, testing and commissioning of NON - RETURN VALVE of following sizes conforming to IS 5312 complete with rubber gasket, GI bolts, nuts, washer etc as reuired 150 mm dia

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.150 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as requiredSingle headed Stainless steel

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :Stainless Steel (Grade 304)

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :Stainless Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.30M

Supplying, installation, testing and commissioning of weather proof M.S door and glass fire door size 2100 mm x 900mm fabricated from 1.6mm thick M.S. sheets and M.S angle 40mmx40mmx6mm complete with glass, locking arrangements to accommodate the following: -a) Gunmetal single headed Hydrant valve - 1 No. b) Fire Hoses 63mm, 15 M long with accessories - 2 Nos. c) Short branch - 1 No. d) First Aid hose Reel - 1 No. e) Fire Extinguisher - 2 Nos. f) Fireman's Axe - 1 No. g) Pressure Gauge - 1 No. The cabinet shall be painted with one coat of primer and 2 coats of synthetic enamel paint of approved shade.

Fabrication, Supplying, Installation, Testing & Commissioning of Electrical Fire Motor Control Panel of cubical construction, floor mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalized with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with solid aluminium strip / single core PVC insulated FRLS copper conductor cable, having suitable mountings for switchgears and accessories and internal control & power wiring with suitable rating PVC insulated FRLS copper conductor, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42 with 500 Amp aluminium bus bar etc complete as required.Fire pane described as above

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.1200 mm

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :Pendent Sprinkler

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.150mm dia

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Supply, Installation, Testing and Commissioning of 100 mm dia Bourden type, Stainless Steel dial type Pressure Gauge including brass isolation valve and siphon pipe having calibration of 0 - 16 Kg / cm2 .

Providing and fixing 25 mm dia inspecting & testing assembly with gunmetal isolation valve, gunmetal sight glass, bypass valve & connected to drain line complete (including the cost of drain pipe).

Supplying and Fixing of Fire Man's axe with heavy insulated rubber as per standard conforming to IS 926.

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.100 mm dia

Supply, Installation, Testing and Commissioning of 100 mm dia Bourden type, Stainless Steel dial type Pressure Gauge including brass isolation valve and siphon pipe having calibration of 0 - 16 Kg / cm2 .

Providing & fixing double flanged Rubber expansion bellow with M.S. fixed flanges (PN-1.6) joint (suitable for system test pressure) of standard length as per manufacturers specs including rubber gaskets, flanges, nuts, bolts and washers complete as required as per specifications.200 mm dia

Providing & fixing double flanged Rubber expansion bellow with M.S. fixed flanges (PN-1.6) joint (suitable for system test pressure) of standard length as per manufacturers specs including rubber gaskets, flanges, nuts, bolts and washers complete as required as per specifications.80 mm dia

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.150 mm dia

Supply, Installation, Testing and Commissioning of 100 mm dia Bourden type, Stainless Steel dial type Pressure Gauge including brass isolation valve and siphon pipe having calibration of 0 - 16 Kg / cm2 .

Detailed GA drawing, flow diagram, equipment list, power load requirementDesign, calculations of all elements of the plant, electrical and mechanical work to satisfy adequacy of designSubmission of detailed GOOD FOR CONSTRUCTION' stage architectural, construction, electrical, mechanical and piping drawing for approval.

Supply, installation, testing & commissioning of 2 Nos. Stainless Steel Perforated Screen with suitable lifting arrangement (approximate size 500 mm wide x 600 mm high) with 10mm & 8mm clear spacing.

Supply, installation, testing & commissioning of non clogging type pumps, having CI casing, CI impeller and SS Shaft complete with all accessories, motor of required capacity. Delivery header with isolation valve, pressure gauge on delivery line with isolation cock level controller with wiring to control the level of sump automatically. Pump shall have following duty.Submersible Sump Pumps in equalisation tank. (2 Nos. 1 working & one standby with a provision of adding one more pump of similar capacity in future).Vendor shall provide the by-pass line back to equalisation tank. (Solid handling cap. 28 mm) Flow rate (each) = 10 m3 / hr Head = 8-10 Mtr (1 set=1w+1s) Make-Kirloskar/Wilo/Lubi

Plant room sump pump 2 Nos (1 working + 1 standby ). Outlet pipe of pump should will be connect in equalisation tank. Provision for made of plant room pump will be start together when increase flow of backwash Flow rate = 8 cum/hr Head= 12 Mts (1set=1w+1s) (Solid handling size for this pump shall be 10 mm). Make-Kirloskar/Wilo/Lubi

Non clogging type horizontal centrifugal Sludge transfer / disposal / recirculation pumps capable of handling solids upto 10 mm, having C.I. casing, C.I. impeller, CS shaft, chrome steel shaft sleeve, IP 55, Class B insulation, mechanical seal complete with all accessories, motor of required capacity, Pressure gauge on delivery line with isolation cock, level controller (with wiring) to control the level of sump automatically. (Solid handling size for this pump shall be 8.5 mm).Flow rate (each) =5.5 m3 / hrHead = 8-10 Mtr (1set=1w+1s) Make-Kirloskar/Wilo/Lubi

Supply, installation, testing & commissioning of positive displacement type screw slurry pump with MS casing, SS-strator with internal rubber lining, gland packing seal, solid handling capacity upto 7 to 10% of the effective percentage of sludge and direct drive with motor. Make : Roto/Rotomac Sludge Feed Pump Capacity : 2m3/hr Head : 40 mtrs. (1W+ 1S)

Supply, Installation, testing and commissioning 2 Nos. twin type rotary air blowers capable of delivering approx. 150 cum/hr of free air at 0.5 kg/cm2 (one working & one standby) with all provisions, driven through “V” belt or directly coupled through flexible coupling to a TEFC motor of suitable HP Suitable for 415 ± 10% volts, 3 phase, 50 cycles A/C supply. Make-Akash/Airvak

Non clog type air dispersion system capable of handling 3-5cfm of air with oxygen transfer with efficiency of 3-4% per/meter water depth. Air dispersion grid in SS shall be assembled in modular form so they can be replaced/repaired easily from platform at the top (fine bubble membrane diffusers)For equalization tank -1 No.

Non clog type air dispersion system capable of handling 3-5cfm of air with oxygen transfer with efficiency of 3-4% per/meter water depth. Air dispersion grid in SS shall be assembled in modular form so they can be replaced/repaired easily from platform at the top (fine bubble membrane diffusers)For sludge holding tank - 1 No.

Non clog type air dispersion system capable of handling 3-5cfm of air with oxygen transfer with efficiency of 3-4% per/meter water depth. Air dispersion grid in SS shall be assembled in modular form so they can be replaced/repaired easily from platform at the top (fine bubble membrane diffusers)Floating Aerated Bio-media Reactor - 2Nos. Make-Universal/MM Aqua

Supply, installation, testing and commissioning of PVC floating media to be installed in Moving Bed Bio- Reactor - 2 Nos. and PVC tube deck settling media in Secondary Settling Tank for 200 KLD daily sewage flow. Make-Univesal/MM Aqua

Supply, installation, testing and commissioning submersible Mixer in Anoxic tank for 200 KLD daily sewage flow (approx. 0.8 H.P.) for phase I only with all provisions to add one more systems in future of 200 KLD. Make-CRI

Supply, installation, testing and commissioning centrifugal monoblock Anoxic Tank recirculation pumps. Quantity: 2 Nos (1 working & 1 stand by) for phase I only with all provisions to add two more sets in future for 200 KLD. Make: Kirloskar/Wilo/Lubi (Solid handling size for this pump shall be 8.5 mm).Flow rate (each) = 20 m3 / hr, Make- KirloskarHead = 8-10 Mtr , 2 HP or as required

Providing fixing testing and commissioning of field/panel mounted pH meter with ABS weather proof IP 65 enclosure, LED indication for high and low pH ± 2% accuracy front keyboard calibration / set point settings. pH Range: 0-14. Make-Aster/eqv.

Providing, fixing, testing and commissioning of single/multi stage, horizontal, centrifugal, 2 pole, 50 HZ, AC, monoblock pumps (as per IS : 9079) incorporating C.I. casing and frame, stainless steel shaft, CI impeller, TEFC induction motor directly coupled to the pump, IP55 protection, class B insulated, C.I. body, hydraulically and dynamically balanced to give vibration free operation, with mechanical seal arrangement, fixed on a base plate with suitable vibration eleminator pads complete with PCC foundation, bolts grouted in CC blocks of 1:2:4, suitably rated DOL / star-delta starter fixed inside main electrical panel complete with level controller, necessary wiring, pressure gauge on the delivery side and strainer on suction side, including non-return valve and isolating valves on suction and delivering sides as required, including suction and delivery headers complete in all respects. Filter Feed Pumps for Recycled Water available from STP. Capacity : 8 M3/hr. Head : 30 MNo. of Pumps 2 Nos. (1 working + 1standby) Make-Wilo/ Kirloskar

Supplying, installing, testing and commissioning of FRP vessel filter with all necessary accessories. Filter shall be suitable for minimum working pressure of 5 kg / cm2 and shall include media, standard fittings like pressure gauges, sampling cock, rinse drain, vacuum breaker etc. Multigrade pressure sand filter media Flow rate : 8 cum/hr Filtration velocity : 17 cum/hr/sqm Shell/Disc thickness : 6/8 mm Filter Diameter : 800 mm. Make: Starlite/Paintair

Supplying, installing, testing and commissioning of FRP vessel filter with all necessary accessories. Filter shall be suitable for minimum working pressure of 5 kg / cm2 and shall include media, standard fittings like pressure gauges, sampling cock, rinse drain, vacuum breaker etc. Activated Carbon Filter Make: Starlite/Paintair Flow Rate : 8 cum/hr Filteration velocity : 17 cum/hr/sqm Shell/Disc thickness : 6/8 mmFilter Diameter : 800 mm

Supply, installation, testing & commissioning of 100 ltrs HDPE/FRP tank with chemical for with 0-6 lph electronic metering type pump and SS agitator complete with motor for chlorine dosing complete as required.Make-E-Dose

Supply, installation, testing and commissioning of Filter Press suitable for 200 KLD daily average flow, plate size 12"x12"x11 nos plate, manual with screw feed pumps 2 nos (1Working+1Standby), with interconnecting piping and poly dosing system of 1 M3/hr @ 40 m head capacity all complete.Make : KWT/Universal

Providing, fixing, testing and commissioning of single/multi stage, horizontal, centrifugal, 2 pole, 50 HZ, AC, monoblock pumps (as per IS : 9079) incorporating C.I. casing and frame, stainless steel shaft, CI impeller, TEFC induction motor directly coupled to the pump, IP55 protection, class B insulated, C.I. body, hydraulically and dynamically balanced to give vibration free operation, with mechanical seal arrangement, fixed on a base plate with suitable vibration eleminator pads complete with PCC foundation, bolts grouted in CC blocks of 1:2:4, suitably rated DOL / star-delta starter fixed inside main electrical panel complete with level controller, necessary wiring, pressure gauge on the delivery side and strainer on suction side, including non-return valve and isolating valves on suction and delivering sides as required, including suction and delivery headers complete in all respects. Treated Water Transfer Pumps Capacity : 6 M3/hr. Head : 30-35 M Power: 5 HP Each or as requiredEach Set No. of Pumps 2 (1 working + 1 standby (1set=1w+1s) Make-Kirloskar/Wilo/Lubi/Leo

Electrical Work Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group A

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 10 sq. mm + 1 X 10 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 4 X 4 sq. mm + 2 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 4 X 10 sq. mm + 2 X 10 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 4 X 16 sq. mm + 2 X 16 sq. mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.3 x 1.5 sq. mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.3 x 4 sq. mm

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Telephone socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required TV antenna socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required Bell push

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 3 Module (100mmX75mm)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 4 Module (125mmX75mm)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 6 Module (200mmX75mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing 3 pin, 5 a ceiling rose on the existing junction box/ wooden block including connections etc. As required.

installation ,testing, commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two gls/cfl/led lamps per fitting, complete with all accessories including connections etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

Providing and fixing extra conduit down rod of 20 mm dia, 2 X 10 cm length wiring with 2 X 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable including painting etc. as required. (Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying and drawing of UTP 4 pair CAT 6 LAN cable in the existing surface / recessed steel / PVC conduite as required 1 run of cable

Supplying and drawing of UTP 4 pair CAT 6 LAN cable in the existing surface / recessed steel / PVC conduite as required 2 run of cable

Supplying and drawing of UTP 4 pair CAT 6 LAN cable in the existing surface / recessed steel / PVC conduite as required 3 run of cable

wiring for group controlled (looped) light point /fan point / exhaust fan point /call bell point (with out independent switch etc) with 1.5 sq mm FRLS PVC insullated cooper conductor with single core cable in surface / recessed PVC conduit , and earthing the point with 1.5 sq. mm FRLS PVC insulated cooper conductor with single core cable as required.Group A

wiring for group controlled (looped) light point /fan point / exhaust fan point /call bell point (with out independent switch etc) with 1.5 sq mm FRLS PVC insullated cooper conductor with single core cable in surface / recessed PVC conduit , and earthing the point with 1.5 sq. mm FRLS PVC insulated cooper conductor with single core cable as required.Group C

Supplying And FIxing SUitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos 3 pin 5/6 A modular socket outlet and 2 nos . 5/6A modular switch , connections etc . As required ( for light plug to be used in non residential buildings)

Supplying And FIxing SUitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 25A modular socket outlet and 25A modular SP MCB “C” curve including connection and painting etc as required

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way, double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)12 way, double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way (4 + 18), Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)4 way (4 + 12), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)12 way (4 + 36), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts 10 KVA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts 10 KVA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts 10 KVA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.100 amps

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 30 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 amps

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 30 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 30 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 amps

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

Supplying and fixing TP sheet steel enclosure on surface/ recess along with 16/25/32amps 415 volts "C" curve TP MCB complete with connections, testing and commissioning etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required450 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 450 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 450 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Reducer with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Reducer with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Reducer with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required 450 mm width X 50 mm depth X 2.0 mm thickness

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 X 16 sq. mm (25mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3½ X 50 sq. mm (35mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3½ X 240 sq. mm (62mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 X 16 sq. mm (28mm)

Supplying and drawing of UTP 4 pair CAT 6 LAN cable in the existing surface / recessed steel / PVC conduite as required 1 run of cable

Supplying and drawing of UTP 4 pair CAT 6 LAN cable in the existing surface / recessed steel / PVC conduite as required 2 run of cable

Supplying and drawing of UTP 4 pair CAT 6 LAN cable in the existing surface / recessed steel / PVC conduite as required 3 run of cable

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.

Supplying, installation, testing & commissioning of fire fighter phone jack complete as required.

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required

Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)12 way (4 + 30), Double door

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.32 amps

Supplying and fixing 63 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 63 amps "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Providing and fixing 65 mm X 10 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 50 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Supply, laying, connection, testing and commissioning of following sizes of 1.1kV grade Single core FRLS PVC insulated Single core sheathed Cable confirming to IS:1554 with Bright annealed copper conductor for 1.1kV voltage grade. It should include both ends terminal joints providing tinned copper terminal lugs, single compression PVC cable glands up to 16 sqmm cable and double compression PVC cable glands for above, insulation tape, effecting terminal connections to the equipment complete as required.1c x 35 sqmm Cu. sheathed FRLS cable

Supply, laying, connection, testing and commissioning of following sizes of 1.1kV grade Single core FRLS PVC insulated Single core sheathed Cable confirming to IS:1554 with Bright annealed copper conductor for 1.1kV voltage grade. It should include both ends terminal joints providing tinned copper terminal lugs, single compression PVC cable glands up to 16 sqmm cable and double compression PVC cable glands for above, insulation tape, effecting terminal connections to the equipment complete as required.1c x 6 sqmm Cu. sheathed FRLS cable

Supply of the following 1100 volts grade, Aluminium/Copper conductor, XLPE insulated, PVC sheathed, steel armoured/Unarmoured cables as per IS 7098 Part-1 and as per technical specifications of this tender and directions of Engineer-in-Charge.50 sq.mm. Al Ar. XLPE cable

Supply of the following 1100 volts grade, Aluminium/Copper conductor, XLPE insulated, PVC sheathed, steel armoured/Unarmoured cables as per IS 7098 Part-1 and as per technical specifications of this tender and directions of Engineer-in-Charge.240 sq.mm. Al Ar. XLPE cable

Supply of the following 1100 volts grade, Aluminium/Copper conductor, XLPE insulated, PVC sheathed, steel armoured/Unarmoured cables as per IS 7098 Part-1 and as per technical specifications of this tender and directions of Engineer-in-Charge.16 sq.mm. Al Ar. XLPE cable

Supply of the following 1100 volts grade, Aluminium/Copper conductor, XLPE insulated, PVC sheathed, steel armoured/Unarmoured cables as per IS 7098 Part-1 and as per technical specifications of this tender and directions of Engineer-in-Charge.10 sq.mm. Cu. PVC Ar. cable

Supply and Receving,storing,installation,testing & commissioning of 1 Mtr Cat 6 patch cord with 23 AWG suitable for Gigabit connection, it should be suitable to maintain the bending radius as per relevant code.

Supply and Receving,storing,installation,testing & commissioning of 2 Mtr Cat 6 patch cord with 23 AWG suitable for Gigabit connection, it should be suitable to maintain the bending radius as per relevant code.

Supply and Receving,storing,installation,testing & commissioning of Cat 6, 24 port loaded rack mountable Patch Panel. The panel should be fully unshielded.

Supply, Installation, Testing and Commissioning of Networking Floor Standing Rack of 15U along with PDU (With surge protection), cable manager, fan etc for Switches, Servers & other accessories etc, complete as required.(At each Floor)

Providing Instaltion, testing commisioning Penta testing, Documentation & Certification of Cat6.

Supply, Installation, testing and commissioning of 4 Megapixel Vandal-resistant Vari focal Dome Camera Ultra H.265 (UL Listed) Progressive scan CMOS, IR-cut filter with auto switch (ICR), 1280x960:30fps, Ultra H.265, H.265, H.264, MJPEG, DC12V & PoE, Weather proof IP67 Protection, Vari-focal lens 2.8 ~ 12mm@ F1.6, Colour: 0.001Lux (F1.6, AGC ON) 0Lux with IR, IR range: up to 30m, IR anti-reflection window, 3-Axis, 2D/3D DNR (Digital Noise Reduction), Digital Defog, Highlight Compensation (HLC), BLC, OSD, Region of intrest, Privacy Masking, Two-way audio Supported, Wide temperature range: -30°C to 60°C (-22°F to 140°F), Edge Storage: Micro SD (up to 256GB), ONVIF (Profile S, Profile G, Profile T). Make : UNV, Milesight, Honeywell (UL Listed).

Supply, Installation, testing and commissioning of 4K H.265+ UHD 32 CHANNELS PROFESSIONAL NVR (UL Listed) 32 IP channels with 320 Mbps incoming bandwidth Having 4 Slots of 10 TB each HDD (Total 40 TB space) Dual LAN interfaces for three network working modes Multi-address/Load Balance/Net Fault-tolerance • Leading-edge Ultra H.265 Compression • Multiple Streams:- Ultra H.265/H.265(HEVC)/H.264+/H.264/MJPEG • Up to 12 Megapixels resolution recording • Support 4K Resolution (UHD) • Support Dual Monitor Display • Support Dual LAN Interfaces for multiple working mode • 2* HDMI port & 2* VGA Port • 2* 100/1000 mbps port • 1*eSATA interface • RAID 0/1/5/6/10 Supported • 1* USB 3.0 Interface • 2* USB 2.0 Interfaces • 1* RCA Audio input • 2* RCA Audio Output Make : UNV, Milesight, Honeywell (UL Listed).

16 Port Network Switch with lightning protection 6000v Support 16 Port PoE + 2 Port Giga Uplink with Extended upto 250M Switch. (Make : Cisco,D-Link, True View, Syrotech.)

Supply, Installation, Testing and Commissioning of Networking Floor Standing Rack of 28U along with PDU (With surge protection), cable manager, fan etc for Switches, Servers & other accessories etc, complete as required.(For CCTV)

Supply, Installation of Connector RJ 45. Make : D-Link/AMP

Supply, Installation of LED TV 49" UHD 4K Display. Make : TCL/LG/Samsung.

Supply, Installation of LED TV 49" UHD 4K Display. Make : Data Socket Outlet (RJ-45)

Supply, Installation of LED TV 49" UHD 4K Display. Make : Wifi Router

Supply, installion, testing and commissioning of UL / FM / VDS Approved Analogue Addressable Multisensor with inbuilt isolator having three sensors One Optical and Dual Heat Sensor (Static and ROR both), It shall have multiple modes with min five different optical sensitivity adjustment from 1.2 - 2.1 %/ft and to be possible to configure the detector to work in any of the modes such as only optical type or only heat type or combined type. 360° Visible Tri-coloured led for Normal, Fault and alarm condition, addressing shall be by means of both Soft addressing or Hard Addressing like dip switches or decade switches or suitable address cards. It shall have Compensation to drift and transient rejection, having IP44 rating and approved to operate in 0°C to +55°C temperature, It shall be possible to insert and remove detectors by a single push twist movement, base shall have special locking tool feature to prevent loosening of detector on its own. (For Detectors/Device without inbuilt isolator, Fault Isolator module to be provided with each detector/device). Make-Advanced/Apollo/Mircom/Secutron/Honeywell-Gamewell.

Supply, installion, testing and commissioning of UL / FM / VDS Approved Analogue Addressable Heat Detector with inbuilt isolator having Dual Heat Sensor (Static and ROR both), It shall have 360° Visible Tri-coloured led for Normal, Fault and alarm condition, addressing shall be by means of both Soft addressing or Hard Addressing like dip switches or decade switches or suitable address cards. It shall have Compensation to drift and transient rejection, having IP44 rating and approved to operate in 0°C to +55°C temperature, It shall be possible to insert and remove detectors by a single push twist movement, base shall have special locking tool feature to prevent loosening of detector on its own. (For Detectors/Device without inbuilt isolator, Fault Isolator module to be provided with each detector/device). Make-Advanced/Apollo/Mircom/Secutron/Honeywell-Gamewell.

Supply, installion, testing and commissioning of UL / FM / VDS Approved Dual Action Addressable Manual Pull Station. It shall have Red Light Emitting Diode (LED) for the Alarm indicator and an Amber/Yellow LED for the Fault indicator. The Pull Station should have provision for a Metallic Key lock for Easy reset.The Pull Station shall have a translucent plastic panel at the center enabling the visibility of an internal LED & the LED should be visible even when the Pull Station is closed with Junction Box and other mounting accessories for proper installation. Make-Advanced/Apollo/Mircom/Secutron/Honeywell-Gamewell.

Supply, install, test and commissioning of UL / FM / VDS approved Analogue addressable Input module with inbuilt isolator / isolator Module with LED indicator to be supplied with Junction Box, Glands and other mounting accessories for proper installation. Make-Advanced/Apollo/Mircom/Secutron/Honeywell-Gamewell.

Supply, Installation, Testing & Commissioning of UL / FM / VDS approved Analogue Addressable Loop Powered Sounder & Visual Strobe with inbuilt isolator / Isolator module and having Min 15 distinct sound patterns/ multitone to indicate Exit doors and direct occupants for safe and fast evacuation variable output starting from 1Hz Frequency flash rate designed for IP65 requirements to be supplied with Junction Box, Glands and other mounting accessories for proper installation. Make-Advanced/Apollo/Mircom/Secutron/Honeywell-Gamewell.

Supply of UL / FM / VDS approved Fire Panel Supervised Voice Evacuation Speaker with 25 & 70 volt line matching transformers and include output power taps of 1⁄4, 1⁄2, 1 and 2 watt(s). High dBA output (over 90 dBA at 10 feet @ 2 watts) with moulded terminal block connection & equipped with a ground wire and frequency response of 400 to 4000Hz for Voice Evacuation with suitable rating amplifiers with Fire alarm panel including. Make-Advanced/Apollo/Mircom/Secutron/Honeywell-Gamewell.

Supply, Installation, Testing and Commissioning of UL / FM / VDS approved addressable Sounder Control Module with Led for Hooter/Speaker Circuit with all mounting accessories complete as required. Make-Advanced/Apollo/Mircom/Secutron/Honeywell-Gamewell.

Supply,Installation, Testing and Commissioning 14 watt of recessed LED downlighter with minimum 1500 lm at minimum 110 lm/W. Luminaire should have die cast aluminum housing and PMMA/PC cover. Minimum lifetime of 50000 hours @L70B50. PF>0.95, THD < 10%. CRI>80, CCT 4000K/6500K as required. Cut out diameter of 150 mm complete with all accesories as required.

Supply,Installation, Testing and Commissioning of 35 watt recessed LED 2X2 panel with minimum 4200 lm @ 120 lm/W. Luminaire should be made of CRCA steel and should have polycarbonate/PMMA diffeser. Luminaire should have PF > 0.95, THD < 10%. Luminaire should have lifetime of minimum lifetime of 50000 hours @L70B50. CRI>80, CCT 4000K/6500K.complete with all accesories as required.

Supply,Installation, Testing and Commissioning of 10 watt LED bulkhead with die cast aluminum housing. Luminaire should have minimum 1100 lm @110 lm/W. Polycarbonate cover. Minimum Ip66, IK09. Lifetime of 50000 hours @L70B50. CRI>80, CCT 4000K/6500K. THD<10%, PF > 0.95.complete with all accesories as required.

Supply,Installation, Testing and Commissioning of 10 watt surface mounted 600 MM long LED tube light complete with all accesories as required.

Supply,Installation, testing and commissioning of (300mm sweep) Exhaust fan 230V,50HZ single phase complete with all accessories as required

Supply,Installation, testing and commissioning of CHANDILIER LIGHTS complete with all accessories as required

Supply,Installation, Testing and Commissioning of floor distribution panel as per detail design and sld.

LISHA ENGINEERS PRIVATE LIMITED (BID ID -400909)

SHREEJIKRUPA BUILDCON LTD (BID ID -400829)