Loading
Loading…
Loading…
| # | Company | Quoted % | Amount | Rank | Status |
|---|---|---|---|---|---|
| 1 | L1₹1.4 LAdmitted-Finance | -21.50% | ₹1.4 L | L1 | Admitted-Finance |
| 2 | L2₹1.6 L+₹19,705.60 (14.2%)Admitted-Finance | -10.34% | ₹1.6 L+₹19,705.60 (14.2%) | L2 | Admitted-Finance |
| 3 | L3₹1.7 L+₹27,810.32 (20.1%)Admitted-Finance | -5.75% | ₹1.7 L+₹27,810.32 (20.1%) | L3 | Admitted-Finance |
Tender Value
₹1.8 L
EMD Value
₹3,520
Closing Date
29 May 2026, 6:00 pmClosed
EE PWD ELECTRIC DIVISION KOTA
EE PWD ELECTRIC DIVISION KOTA
SUPPLY AND INSTALLATION OF APFC PANEL IN CIRCUIT HOUSE DISTRICT- BUNDI
2026_CEPWD_561892_4
EE PWD ELECTRIC DIVISION KOTA NITNO05-2026-27
Open Tender
Civil Works
Percentage
180 days
BUNDI
Please refer Tender documents.
2 documents required · 2 mandatory
₹200
200 AS PER NIT
₹3,520
Yes
4 Jun 2026
22 May 2026
1 Jun 2026
22 May 2026
29 May 2026
22 May 2026
This is a percentage-rate BOQ. The schedule below shows estimated quantities and rates. Bidders quote a single percentage above or below the total estimated cost.
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1Supplying and laying FR PVC insulated & unsheathed flexible copper conductor of following nominal sizes with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. | |||||
| 1.01 | 1 x 1.5 sq.mm | 55 | Mtr. | 22 | ₹1,210 |
| 1.02 | 3 x 2.5 sq.mm | 30 | Mtr. | 103 | ₹3,090 |
| 1.03 | 3 x 4 sq. mm. | 30 | Mtr. | 161 | ₹4,830 |
| 1.04 | 3 x 6.0 sq. mm. | 20 | Mtr. | 223 | ₹4,460 |
| 2Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanism , energy limiting of class 3 as per IEC, minimum phase termination capacity of 25 sq.mm., conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating, 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. | |||||
| 2.01 | Single pole MCB (With B / C curve tripping characteristics)
6 A to 32 A rating | 6 | Each | 169 | ₹1,014 |
| 2.02 | Triple pole MCB (With B / C curve tripping characteristics)
6 A to 32 A rating | 4 | Each | 884 | ₹3,536 |
| 2.03 | Triple pole MCB (With B / C curve tripping characteristics)
40 A rating | 4 | Each | 1,358 | ₹5,432 |
| 3SITC of IP-42 and general construction confirming to IS:8623 : 1993, wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as specifications and Other parameters required as per point (a) ,(b), (c),(d), (e), (f), (g), (h) as below:- (a) Thickness of CRCA sheet shall not be less than 1.6 mm upto 450 mm length/ width of any compartment and be 2.0 mm above 450 mm, load bearing structure shall be 2.0 mm thick sheet supported by base M.S. channel if required, cable alley compartments having concealed hinged type doors with key type lock with / without detachable extension type structure. Removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided (b) complete panel shall undergo a process of degreasing, Water rinsing, Activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then Powder coated with approved shade of minimum 70 microns on both side(Inner & Outer side) of panel. The panel having PE foam/ Neoprene rubber gasket of not less than 3mm thickness ,required hardware , concealed hinged door with key type locking arrangement for equipment/switchgear earthed with 2.5 sq.mm braided copper wire. [c) Interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 63 amp ) and by solid bus bar (>63 amp ) . control wiring will be carried out with 1.5 Sq.mm, Earth wire with 2.5 Sq.mm and CT with 2.5 sq.mm flexible copper wire only. All joints / interconnections of copper bus bar shall be dully tinned . Clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar Bus bar is insulated by Heat Shrinkable sleeves . Earth and Neutral bus bar shall be half of the size of phase bus bar. ( Cost of Bus bar / Flexible wire for Interconnection between Main busbar and Switchgear is to be Paid Extra ) | |||||
stage.html
html • 0.03 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 1.50 MB
Tendernotice_2.pdf
PDF • 1.49 MB
BOQ_999851.xls
BOQ • 0.28 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .