Constrution of Guest House Building of APEPDCL at 33/11 KV SS, Lalacheruvu premises in Rajamahendravaram Division of East Godavari Circle

Earth work excavation in ordinary soils by manual means upto 3m depth for foundations and depositing on bank for all lifts and with an initial lead of 10m including all operational, incidental, labour charges such as shoring ,sheeting, planking, strutting, etc. complete for finished item of work including seigniorage excluding dewatering charges etc as per SS - 20 B (APSS 308).

Filling with useful available excavated earth (excluding rock) in trenches, sides of foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work. (APSS NO. 309 & 310)

Filling with sand in foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work. (APSS NO. 309 & 310)

Plain Cement concrete (1:4:8) using 40 mm metal with concrete mixer including cost and conveyance of all materials and all labour charges complete.

Supplying, cutting and placing HYSD bar reinforcement as per drawings and technical specifications for Bars below 36 mm dia including over laps and wastage, where they are not welded including cost and conveyance of all materials to site and all labour charges complete.

Providing Pre construction Anti termite is a process in which 1. chemical toxic to subterranean termites is apply/ inject into soil during early stage of building Construction 2. Treatement of soil Beneath the building and around the foundations conduct and chemical use as per BIS - IS 6313 (Part -2) 2013 code specification & CIB RC registered termiticide which creates a continuous chemical barrier beneath the building which kills or repels terminates & impervious to tremite entryImidacloprid 30.5% SC (IS 63131) dissolve 2.1 Ml/1 liter of water and apply emulsion/solution @ 7.5 Litres/Square meter (Sqm) of internal, external vertical surface of the colums , plinth beams (Back filling) walls and floor junction, external perimeters, along reatining wall @ 5.0 Liters/Sqm of the horizontal surface of basement top surface of the basement filling below flooring bed (Plinth) & @ 2.0 Litres/ Line meter at expansion joints. The substructure of a depth of 500mm around coulmns & 300mm deep around plinth beams, basements & floor filling area including excavation channel along the wall & rodding etc. cost & Conveyance of all materials to the site, cost of labour for sparying, rodding etc. complete for furnished item of work as per the approval of the Engineer-in-charge

Brick Masonry in CM (1:5) with Fly ash cement/lime solid blocks with compressive strength of 75 kg/sq.cm - IS:12894-1990 - CLASS - 7.5 - 290 x 200 x 140 mm including seignorage charges including cost and conveyance of all materials to site and all labour charges complete.

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. FOOTINGS

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. PLINTH BEAM

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. LINTEL BEAMS - GROUND/FIRST FLOOR

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. LINTEL BEAMS - SECOND FLOOR

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. LINTEL BEAMS - THIRD FLOOR

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. COLUMNS- GROUND/FIRST FLOOR

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. COLUMNS- SECOND FLOOR

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. COLUMNS- THIRD FLOOR

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. SUNSHADES - GROUND/FIRST FLOOR

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. SUNSHADES - SECOND FLOOR

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. SUNSHADES - THIRD FLOOR

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. ROOF BEAMS - GROUND/FIRST FLOOR

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. ROOF BEAMS - SECOND FLOOR

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. ROOF BEAMS - THIRD FLOOR

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. ROOF SLAB - GROUND/FIRST FLOOR

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. ROOF SLAB - SECOND FLOOR

VRCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering and scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work. ROOF SLAB - THIRD FLOOR

Providing impervious coat to exposed RCC roof slab surface with CM(1:3), 20mm thick with 1kg of water proof compound per bag of cement laid over roof when it is green including cost of all materials, seigniorage charges, conveyance charges of materials and including all operational, incidental and labour charges for mixing mortar, laying, rendering smooth and thread lining, curing, rounding off junctions of wall and slab etc,, complete for finished item of work

Brick Masonry in CM (1:6) with 2nd class Bricks traditional size 23 x 11 x 7 cms including cost and conveyance of all materials to site and all labour charges complete-GROUND/FIRST FLOOR

Brick Masonry in CM (1:6) with 2nd class Bricks traditional size 23 x 11 x 7 cms including cost and conveyance of all materials to site and all labour charges complete - SECOND FLOOR

Brick Masonry in CM (1:6) with 2nd class Bricks traditional size 23 x 11 x 7 cms including cost and conveyance of all materials to site and all labour charges complete - THIRD FLOOR

11.5 cm wide Brick masonry for super-structure on ground floor in cm (1:4) using second class traditional size bricks including cost of all materials and it's conveyance, labour and all operations for constructing half brick masonry, mixing cement mortar, curing etc.,complete.- GROUND/FIRST FLOOR

11.5 cm wide Brick masonry for super-structure on ground floor in cm (1:4) using second class traditional size bricks including cost of all materials and it's conveyance, labour and all operations for constructing half brick masonry, mixing cement mortar, curing etc.,complete.- SECOND FLOOR.

11.5 cm wide Brick masonry for super-structure on ground floor in cm (1:4) using second class traditional size bricks including cost of all materials and it's conveyance, labour and all operations for constructing half brick masonry, mixing cement mortar, curing etc.,complete.- THIRD FLOOR.

Plastering with CM (1:3), 12 mm thick in one coat for inernal faces of ceilings etc.,including cost and conveyance of all materials all labour charges etc, complete.- GROUND/FIRST FLOOR

Plastering with CM (1:3), 12 mm thick in one coat for inernal faces of ceilings etc.,including cost and conveyance of all materials all labour charges etc, complete.- SECOND FLOOR

Plastering with CM (1:3), 12 mm thick in one coat for inernal faces of ceilings etc.,including cost and conveyance of all materials all labour charges etc, complete.- THIRD FLOOR

Plastering with CM (1:5), 12 mm thick in one coat for inernal faces of walls, ,including cost and conveyance of all materials all labour charges etc, complete.- GROUND/FIRST FLOOR

Plastering with CM (1:5), 12 mm thick in one coat for inernal faces of walls, ,including cost and conveyance of all materials all labour charges etc, complete.-SECOND FLOOR

Plastering with CM (1:5), 12 mm thick in one coat for inernal faces of walls, ,including cost and conveyance of all materials all labour charges etc, complete.-THIRD FLOOR

Plastering with CM (1:5), 20 mm thick in one coat for external faces of walls including cost and conveyance of all materials all labour charges etc, complete. - GROUND/FIRST FLOOR

Plastering with CM (1:5), 20 mm thick in one coat for external faces of walls including cost and conveyance of all materials all labour charges etc, complete. - SECOND FLOOR

Plastering with CM (1:5), 20 mm thick in one coat for external faces of walls including cost and conveyance of all materials all labour charges etc, complete. - THIRD FLOOR

Laying P.C.C.(1:2:4) using 10 to 12 mm HBG metal including cost and conveyance of all materials to site and all labour charges complete for finished item of work.

Flooring with digital / polished glazed full body porcelain vitrified tiles with any type of design texture such as marble finish, wooden, bamboo, stone finishes etc., scratch less, stain free and Size 900 x 900 mm and thickness between 9-11 mm of 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs Make: Somany,HR, Jhonson,Naveen Ceramics, Kajaria, Nitco, Sphinx, RAK or equivalent set over base coat of cement mortar (1:8), 12 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3.kgs per sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, sand water and tiles etc., complete, for finished item of work including the cost of conveyance of all materials.

Flooring with 8mm thick Non-skid edge cut rectified ceramic tiles Ist quality , set over base coat of cement mortar (1:8), 12 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3kgs per sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, sand water and tiles etc., complete, including seigniorage charges, etc., complete for finished item of work, including the cost of conveyance of all materials.

Providing and applying synthetic plaster putty or plaster of paris putty or lime punning of average 1 to 2mm thickness over plastered surface to prepare the surface even and smooth after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, applying knifing paste filler by putty knife/muslin pad, air dry for 2-3hrs, sand with 180 and 320 No., emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work for internal walls.- GROUND/FIRST FLOOR

Providing and applying synthetic plaster putty or plaster of paris putty or lime punning of average 1 to 2mm thickness over plastered surface to prepare the surface even and smooth after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, applying knifing paste filler by putty knife/muslin pad, air dry for 2-3hrs, sand with 180 and 320 No., emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work for internal walls.- SECOND FLOOR

Providing and applying synthetic plaster putty or plaster of paris putty or lime punning of average 1 to 2mm thickness over plastered surface to prepare the surface even and smooth after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, applying knifing paste filler by putty knife/muslin pad, air dry for 2-3hrs, sand with 180 and 320 No., emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work for internal walls.- THIRD FLOOR

Painting with acrylic EXTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre exterior grade of approved brand and colour/shade two coats over a base coat of appropriate primer (grade-II) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.- GROUND/FIRST FLOOR

Painting with acrylic EXTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre exterior grade of approved brand and colour/shade two coats over a base coat of appropriate primer (grade-II) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.-SECOND FLOOR

Painting with acrylic EXTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre exterior grade of approved brand and colour/shade two coats over a base coat of appropriate primer (grade-II) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work.-THIRD FLOOR

Painting with synthetic polymer plastic INTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and shade two coats over a base coat of appropriate interior primer(grade-I) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work - GROUND/FIRST FLOOR

Painting with synthetic polymer plastic INTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and shade two coats over a base coat of appropriate interior primer(grade-I) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work - SECOND FLOOR

Painting with synthetic polymer plastic INTERIOR emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and shade two coats over a base coat of appropriate interior primer(grade-I) of approved brand, making 3 coats in all to give an even shade after thorughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and convyance of all materials, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work - THIRD FLOOR

Providing R.C.C. plates of 38mm thick with R.C.C.(1:1.5:3) (including cost of steel reinforcement ) and plastering with CM(1:5),12mm thick including cost and conveyance of all materials to site and all labour charges complete.

Providing of RCM facia or drop wall 5cm thick in CM (1:3) including seignorage charges with rabbit wire mesh (chicken mesh) of not less than 30gauge & nominal reinforcement as directed by Engineer-in-charge with dubara sponge finishing, including cost & conveyance of all materials to site, scaffolding charges and all labour charges complete.

Providing and fixing factory made UPVCwhite colour sliding glazed window upto1.50m in height dimension comprising of uPVC multi chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60±0.2mm thick galvanized mild steel section made from roll forming process of required length (shape & sizeaccording to uPVCprofile), appropriate dimension of UPVC extruded glazing beads and UPVC extruded interlocks, EPDM gasket, woolpile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be40kg), G.Ifasteners 100x8mm size for fixing frame to finished wall and necessary stainless steel screwsetc. Profile offrame & sash shall be mitred cut andfusion welded at all corners, including drilling of holes for fixing hardware's and drainage of wateretc. After fixing frame the gap between frame and adjacent finished walls all be filled with weather proof silicon sealent over backer rod of required size and ofapproved quality, all complete as per approved drawing & direction of Engineer -in - Charge inclusive of cost of Single/double glasspanes, wiremesh and silicon sealent .Note: For uPVC frame and sash extruded profiles minus 5%tolerancein dimension i.e. in depth &width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted but no extra payment onthis account shallbemade.Two track two panels sliding window made of (big series)frame 67 x 50 mm & sash 46 x 62 mmboth having wallthickness of 2.3 ± 0.2 mm and singleglazing bead / doubleglazing bead of appropriate dimension .(Area of window upto 1.75 sqm ).

Supply and fixing of M.S. grill to Ground floor windows with 10mm square solid rods with 25mm x 25mm x 5mm L Angle and approved design given by the department and as directed by the engineer at site including cost and conveyance of all materials and all labour charges etc., complete.

Flush door: supply and fixing of 35 mm thick flush door single shutter, solid bond wood block board type with teak veneer on both faces including 5mm thick glass and supplying positioning and fixing door frame with well seasoned assam teak/beeja sal/sal wood scantlings of size 100 mm x 75 mm, including 6 nos. Of ms 'z' hold fasts of size 250x50x8 mm,including aluminium 3 nos. Of 125 mm butt hinges, 1 no. Door stoper, 2 no. 100 mm long door handles , 1 no. Aldrop of size 250 mm long , 1 nos. Of 200 mm long tower bolts, with bolts, nuts, nf screws including cost and conveyance of all materials to site, labour charges etc., including minor extra fixtures required if any as directed by the engineer-in-chrge of the work complete for finished item of work

Providing and fixing Aluminium Extruded Section Body Tubular Type Hydraulic Door Closer (IS: 3564) with double speed adjustment with necessary accessories and screws etc. complete (Type-3: for width of doors 851 to 1000 mm)

Providing and fixing of Wood Polymer Composite (WPC) solid doors with frame. Door shutter consists of Wood Polymer Composite (WPC) solid, frosty white single extruded factory made in 18 MM thickness (Density 650 kg/Cum, Weight 35Kg) and Door Frame consists of solid Wood Polymer Composite (WPC) single extruded section of size with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebat of 32MM. Door Frame section of 45x75 MM . The two Vertical members are to be joined together with the horizontal member using 8x50 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member and with fixtures 1no aluminium aldrop 200mm lond and 2nos tower bolt 150mm long, the rate is inclusive of cost and conveyance of all materials to site and all labour charges complete.

Supplying and fixing Gyp Board Suspended regular single layer false ceiling (GS-MFSC-4.1 as per India Gypsum) using 12.5 mm thick Gyp Board conforming to IS 2095 - 1982 fixing to Gyp steel GI perimeter channels of size 20 mm x 27 mm x 30 mm(web) of 0.55 mm thick along the perimeter of ceiling screw fixed to brick work/ partition at 610 mm c/c and suspending the frame work using Intermediate channels (45 mm x 15mm x 15mm x 0.9 mm) from soffit at 1220 mm c/c with ceiling angle (25 mm x 10 mm x 0.55 mm) fixed with GI Cleat and steel expansion fasteners & connecting clip to the ceiling channels (with knurled web of 51.5 mm x 26 mm x 10.5 mm x 0.55 mm) fixed in direction perpendicular to the intermediate channel at 457 mm c/c and fixing the 12.5 mm tapered edge Gypboard with 25 mm drywall screws at 230 mm c/c & jointing and finishing using joint compound and paper tape to have a flush look including filling the tapered & square edges with jointing compound, two coats of drywall topcoat complete for finished item of work as per India Gypsum Ltd specification.

Supply, fabrication and fixing of stainless steel railing of approved design with Stainless Steel Tubes, sections, plates, sheets & pipes of all sizes & diameters for grade -304 including all accessories and all labour charges complete for finished item of work.

Supply, Installation and commissioning approved make floor mounted close coupled EWC suit CASCADE model 'P' or 'S' trap with dual flush porcelain cistern fixed on EWC with all internal parts of dual flush cistern, ultra solid seat cover of approvedmake with rubber buffer and cap 15 mm angle stop cock 450 mm long PVC inter connection pipe wall flanges all of approved make etc. complete for finished item of work in all respects: Special Colour - Grade - III of make: Parryware/CERA/RAK or its equivalent as approved by the deaprtment.

Supply and fixing of 110 mm dia (6kg/sqcm) PVC pipes including cost and conveyance of all materials all labour charges etc., complete.

Supply and fixing of 75 mm dia (6kg/sqcm) PVC pipes including cost and conveyance of all materials all labour charges etc., complete.

Supply and fixing Indian make Flat Back Wash Hand basin with pedestal (HSW/Parryware/Neycer) 1st quality conforming to IS:2556-Part-4:1972 with waste fittings like rubber plug, chain, 32mm nominal size C.P. Fitting with parallel pipe thread conforming to IS:2963-1979 and fitted with 15mm nominal bore chromium plated pillar tap of 1st quality Indian make 400 grams Seiko/Senior/Nice/Esso or equivalent complete with standard CI brackets : 550 x 400 mm - double C.P. Pillar cock.

Supply and Fixing of Premium make CPVC Pipes of 1" dia (28.60mm ODPipe - SDR 13.5) and Fittings to meet the requirement of ASTM-D 2846 having the same physical Properties for Hot and Cold Water (IS 15778:2007)

Supply and Fixing of Premium make CPVC Pipes of 1/2" dia (15.90mm OD Pipe - SDR 13.5) and Fittings to meet the requirement of ASTM-D 2846 having the same physical Properties for Hot and Cold Water (IS 15778:2007)

Supply and fixing CP Long body bib cock facy type deluxe heavy duty 12.7mm dia Indian make Seiko/Senior/Nice or equivalent

Supply and fixing CP Short body bib cock facy type deluxe heavy duty 12.7mm dia Indian make Seiko/Senior/Nice or equivalent

Supply and fixing PVC 1" gate valve including cost of PVC pipe, bends, couplings and Running Joints etc., complete.

Providing & Placing on Terrace(at all floor levels) polyethylene water storage tank with Double layer approved brand & manufacture with cover and suitable locking arrangement & making necessary holes for inlet & outlets and over flow pipes but without fittings & base support for tanks Polyethylene water storage tank double layer conforming to IS:12701-1996 with lid.

Supplying and Fixing 76.2 mm Nahny Trap 1st quality in RCC floors

Supply and fixing of soap stands in the washroms including cost and conveyance of all materials, labour charges etc.,

Supply and fixing of 25.4 mm dia& 609.6 mm long aluminium anodized towel rod with brackets and aluminium screws including cost and conveyance of all materials, labour charges etc., complete

Supplying & Fixing white glazed flat back half stall urinals 1st quality conforming to IS:2556-1995 with standard C.P. Spreader of overall size 95 x 95 x 57 mm conforming to IS:2556-Part6, Sec-6-1974 fixed with screws complete Indian make (HSW/Parry/Neyce

Supply and Fixing of 25mm outer dia (1.6-1.8)mm thick rigid P.V.C. pipe (ISI MARK) of make Sudhakar /Macoplast/Modi with all required accessories like bends, junction box with cover etc., including all labour charges etc., complete.

Wiring with 2 runs of 14/0.3mm (1.0 Sq.mm) Fire Retardant (FR) P.V.C. insulated flexible copper cable (ISI MARK) in existing pipe with 6A modular switch, Ceiling rose and hot dip galvanized metal boxes with cover frame to switch control box including all labour charges etc., complete for light, bell, fan and exhaust fan points in Non-Residential Buildings (makes Anchor / Gold Medal / Million / Vimal / Maru / Milltec.)

Providing 6A modular switch with 3 No 3/2 pin socket, and hot dip galvanized metal boxes with modular cover frame to switch control box including all labour charges etc., complete in Non-Residential Buildings Legrand Arteor / Schneider Zen celo/ Crabtree Murano or Ducor /L&T-englaze/ GM-(Four-Five)/ Goldmedal(GIFA)

Supply and run of 4 of 36/0.3mm (2.5 Sq.mm) F.R P.V.C. insulated flexible copper cable in existing pipe for mains inlcuding all labour charges etc., complete.

Wiring with 4 runs of 56/0.3mm ( 4.0 Sq.mm) Fire retardant (FR) P.V.C. insulated flexible copper cable (ISI MARK) in existing metalic/ Non- metalic conduit pipe for run of mains including all labour charges etc.,from LDB at each floor to the Board.

Supply and fixing of 8way SPN Distribution Board with IP 43 protection concealed in wall including chisiling, masonry work & suitable for S.P. out going MCBs in sheet steel enclosure with 1no. 63A FP Isolator and 4 Nos 6-32A SP MCBs including (make Makes: Legrand(Ekinox 3) / Schneider-A9/Hager -Novello+/ Seimens/Havells STADx/ Lauritz Knudsen (Formerly L&T) -Newrange/Indo Asian-Opti Pro/ HPL (Techno)/ Anchor (Uno Plus) ) complete for finished item of work as per directions of Eng-in-charge.

Providing independent earthing by excavating a trench to a depth of 2.1 M in all soils, as per size specified in the Data, using 40mm dia 'B' class GI pipe of 2.5 Mtrs length with necessary accessories with hume pipe ring duly providing staggered holes including filling with equal proportion of Salt and Charcoal in layers and all labour charges etc., complete for small quarters.

Supply and fixing of 20W,1900lumens T8,not less than 1100mmlength LED retrofit tube light withaluminium anodised body, inputvoltage AC 220 - 260 Volts withPF>0.9, Surge protection: 2KV,THD<10%, with inbuilt driver and frosted cover CCT: 3000K - 5700K,minimum CRI>70, .etc., complete as per IS 10322 (Part 5/ Sec 1)..2012 Makes : As per list of recommended brands as category II.

Supply and fixing 48" (1200mm) Sweep Ceiling Fan of makes (Crompton High speed/Bajaj Ultima/Havells Velocity/ Usha Astra/ Orient Summer Pride) with Modular Electronic Regulator of makes (Crab Tree/Feno Swtch/ Toyoma/Fortune Art/ Million / Gold Medal / Vimal / Anchor Roma)

Supply and fixing of (7 to 9)W LED Lamp with input voltage 90 to 300V, Color temperature 3000k - 6500k, Beam angle 170 - 220 degrees, B22 base.Makes: Phillips /Crompton / Bajaj / Havells / Halonix/GM/HPLSyska / Green Lites / Fortune Arrt / GoldMedal / Luker/Leo/Orbit /Rhino / GLO LED/Million/Victoria/Benlo/Goldwyn

Supply and fixing of 24W LED Slim Panel Round / Square suitable for Recessed / Surface mounting made of diecast alluminium body with powder coating, acrylic diffuser with Driver as per IS: 15885 (Part 2/ Sec 13) : 2012 , operating voltage range of 150 to 265 Volts AC, P.F > 0.9, Surge protection: 2KV,THD<10%, with high power LED's having acy of > 120 lumins/watt,CCT: 3000K - 5700K, minimum CRI>70, .etc., complete Makes : VIN/Surya / Fortune Art / Syska / GM / Green Lites / Gold Medal / C&S / Pharox / Anchor asonic / Stanjo/Ib LED/Promtec/Eveready/Enrich/Opple b) LED MAKE : CREE / NICHIA / OSRAM / SAMSUNG / EVERLIGHT/ San'an

Supply and fixing of one 6A modular switch control & two 6A 3/2 pin socket and one 16A modular switch control and one 16A 3/2 pin socket on white coloured modular box with cover frame on separate board including all labour charges etc., complete but exluding the cost of wire. (makes Crabtree/Feno Switch/Toyoma/Fortune art)

Supply of 25 Sqmm 3.5 Core XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I) Makes: RPG / Finolex / Finecab / Paragon / V-Guard / Fortune Art / Suncab / Orbit.

Supply and fixing of Porcelain Rewirable 100A Fuse Units with wooden board. Makes: C&S/Standard/HPL/ Sputnik / Million / Gold Medal / Benlo /Anchor including all labour charges etc., complete

Supply and fixing air exhaust fan of light duty metallic blades 300mm(12") 900 R.P.M with double ball bearing and wire guard etc., complete of makes Crompton/Bajaj Bahar WG/ Havells Ventil Air - DS / Orient hill air.

Supply & Fixing of Wall Mixer with provision for over head shower and 115mm long bend pipe with wall flange Jaquarmake Continental series, Chrome finish with7yearswarranty.

Providing and fixing Structural Glazing fabricated from Roll formed sections made of Pre-painted Steel / Powder coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS 277 with Zinc of 120 Gm/Sqm) with total coated thickness of 0.72 mm and the glass holding section made of 304 grade stainless steel of 0.58 mm thick galvanised steel section as stiffeners inside the colour coated steel powder coated sections as per the design requirement & calculations to suit wind pressures as given in IS: 875, the primer coat with epoxy primer of 5 – 7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with Alkyd backer of 5-7 microns or powder coated with pure polyester powder up to 50-60 microns thick and the vertical section of 50 mm x 99 mm x 0.72 mm, 33 mm x 56 mm x 0.72 mm for frame horizontal section, stiffener section of 47 mm x 97 mm x 1 mm, cover profiles sections of 20 mm x 58 mm x 0.58 mm, glass holding section of 37 mm x 37 mm & 37 mm x 18 mm including fixing 5mm thick Ocean Blue reflective glass, brackets made of CRCA powder coated/Electroplated to connect vertical to horizontal, vertical to slab, to fix verticals at top & bottom as per site requirement and gasket made of Ethyl Propylene Diamine Monomer, U.V. resistant silicon sealant including fixing in concrete/masonry wall with self-expanding cap & screws inclusive of cost and conveyance of all materials to site, all labour charges, incidental charges, cost of all consumables etc. and fixing charges complete for finished item of work.

Supply and fixing of 1.8/1.9/2.0TR, 5 Star capable of delivering not less than 21600 BTU/hr and above with operating on refrigerant R-410A / R-32 Makes: As per list of recommended brands as category II. INVERTER Model Cool type split AC unit with high wall mounted Single Split indoor unit and outdoor condensing unit Hermetically sealed compressor suitable for operation on 230V, 50Hz, 1Phase AC supply capable of performing Heat cool dehumidifying air circulating and filtering with cooling and condensing units with 3 mts of copper piping, insulation kit and 4 mts of 4 core copper flexible chord with cordless remote control etc., dual barrier coating in order to protect coil form oxidation. Makes: Blue star / Hitachi / Daikin/Lloyd (prevailing models in the market)

Supply, Fabrication of 1set MS bracket suitable for fixing outdoor unit of split AC unit.

Supply and istallation of 5.0KVA Stabilizer of Makes: V-Guard / Real Guard / Uni Stab / ITL.

Providing and fixing box work / ward robe with properly treated ply wood material with antitermite coating, care should be taken for no reflected sound, 18MM BWR plywood should be used as a backing sheet and finished with selected laminated/Veener (costing between 60 - 70persft) sheeting goorves should be given as per design and grooves lines be maintained for every joint, provision for switch board and electrical box should be given with all complete material and labour complete .

Providing and fixing wall pannelling as per design with properly treated plywood material antitermite coating and care should be taken for no reflected sound, 18MM BWR plywood should be used as a backing sheet and finished with selected laminated/veener (costing between 60 - 70persft) sheeting goorves should be given as per design and grooves lines be maintained for every joint, provision for switch board and electrical box should be given with all complete material and labour complete

Supply and fixing of full height partitions with frame made of G.I stud section of size 48mm x 35mm x 0.55mm thick inclusive of door placed vertically and at 1200mm internals horizontally fixed to the wall by means of self expansion screws and caps. 12mm plywood fixed on both sides of the frame by means of self-taping screws placed at every 300mm intervals. Fixing laminate of 1mm thick on the plywood. Necessary provisions shall be made for electric swithes and other accessories as per requirement. The cost is inclusive of conveyance of materials, Labor charges etc., complete for finshed item of work as per the direction of Engineer in charge.

Supply, fabricating and fixing of bed side tables solid bond wood block board type with painting/laminate on both faces and supplying positioning and fixing door frame with 18mm plywood and door handles, with bolts, nuts & screws including cost and conveyance of all materials to site, labour charges etc., including minor extra fixtures required if any as directed by the engineer-in-chrge of the work complete for finished item of work

Providing and fixing head board back pannel with resnin fabric as per design with properly treated acoustic material antitermite coating and well insulated with glass wool care should be taken for no reflected sound,18MM BWR plywood should be used as a backing sheet and finished with selected laminated/veener (costing between 60 - 70persft) sheeting goorves should be given as per design and grooves line should be maintained to match the next sheet fixing 12mm grooves should be maintained for every joint, provision for switch board and electrical box should be given with all complete material and labour complete .

Supply and fixing of wall papers to partition walls with standard ISI company/brand with 100% water proof PVC paper and Korean imported paper for longlasting usage as per design inclusive of all labour charges,materials, conveyance as per design complete for finished item of work.

Supply, Transport and Delivery of Malaysian Leatherette Sofa Set consisting of 3 Seater Length : 80inches x Width : 34 in x Height : 38in + 2 Seater Length : 59.5inches x Width : 34in x Height : 38in and 1 Seater Length : 39inche x Width : 34in x Height : 38in with luxurious leatherette upholstery intricate quilting high backrest Solid Wood Frame Construction inclusive of all labour charges,materials, conveyance as per design complete for finished item of work.

Supply, Transport and Delivery of designer Italian Glass Center Table Length:47.2 x Width : 23.6 x Height: 17.5 Inches is dual tone coloured made from MDF and tempered glass on top inclusive of all labour charges,materials, conveyance as per design complete for finished item of work.

Supply, Transport and Delivery of Penang Malaysian Dresser in Melamine Finish and functional piece of furniture made from HDF with a high gloss finish, which makes it durable and easy to care features ample storage space, with open corner shelves inclusive of all labour charges,materials, conveyance as per design complete for finished item of work.

Supply, Transport and Delivery of 65Inch LG UR90 65 (164cm) 4K UHD Smart TV | HDR10 Pro | Local Dimming α5 AI Processor 4K Gen6 with AI Brightness & 4K Upscaling Magic Remote : Universal Control, Point, Click, Scroll, Voice AI Sound Pro (Virtual Surround 5.1.2) for an Immersive Experience Smart WebOS platform with OTT Apps like Netflix, Prime Video, Disney+ Hotstar and many more ALLM, HGIG Mode for a Better HDR Gaming Experience inclusive of all labour charges,materials, conveyance as per design complete for finished item of work.

Supply, Transport and Delivery of DECO WINDOW Multicolour Printed Jacquard Door Curtains for all doors and windows of suite rooms cost includes the fabric, tailoring as per design complete inclusive of all labour charges,materials, conveyance as per design complete for finished item of work

supply and fixing double cot bed of king size not less than 1.80mx2.1m of seating height of 0.45m above ground level. The laminate color should be matched to the interior color , the foam used used for bed should be 40mm density , supplied with two pillows , should be supplied with two sets of bed sheets and pillowcovers , should be complete item as approved by Eng in chief

Supply of Decorative items, Crockery and other miscellenous items

Providing and fixing powder quoted aluminium louvers windows with frame,aluminium glazing plate etc. complete (minimum thickness of polyester powder coating 50micron ivory color) of approved design/pattern, frame sections, making the louvers windows to proper sizes around the openings and fixing over the top of existing partition wall of Aluminium frame work with C.P. brass/ stainless steel screws @ 200 mm centre to centre, all complete as per site conditions, requirement and direction of Engineer-incharge.

Supplying and fixing aluminium composite cladding with skin material 0.5 mm thick aluminium sheet cover material natural polyethylene aluminium cladding panel fixed with extruded aluminium basis frame (50x25x1.5mm) angle cleats,weather sealants, rivets, GI brackets all as approved, using suitable bolts on structural steel work including necessary accessories complete in all respects including all scaffolding and labour charges etc., complete for finished item of work but excluding cost of structural steel fabrication, if any.

Supply and Spreading the Stone crusher dust finer than 3mm with not more than 10% passing 0.075 sieve and consolidating deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work.

Providing of LDPE sheet (Geo membrane ) 500 micron thick including cost and conveyance of all materials to site and all labour charges complete.

Vibrated PCC (1:2:4) using 20 mm size HBG metal from approved quarry including cost and conveyance of all materials and all labor charges for laying of concrete with all leads and lifts and all other incidental charges etc., complete.

Providing Mastic pad 2'0" x 4'0" (0.6 M X 1.2 M ) of 1/2" (12.7 mm ) thick including cost and conveyance of all materials to site and all labour charges complete.

Filling with good gravel in low lying area with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work. (APSS NO. 309 & 310)

Supply and fixing of 12mm thick toughned glass partition along with 0.45 mm line stickering as per Eng-in-charge with all complete patch fitting from floor to ceiling and with necessary hole cutting for locks and patch fitting.

Providing Landscaping services like preparing and laying of grass mats along with shrubs hedges and flowering patched for the entrance area of the Guest house as per approved design of the department.

Providing Consultancy services for designing and interiors inclusive of site visits

Supply and fixing of 15U Wall mount Rack with shelf and cable manager make Legrand including all materials and labour charges etc., complete.

Supply and fixing of 24 Port fully loaded Jack Pannel make Legrand including all materials and labour charges etc., complete.

Supply and fixing of 1 cat6 feet patch cords make Legrand including all materials and labour charges etc., complete.

Supply and fixing of Cat 6 UTP Cable Box (305mtrs) make Legrand including all materials and labour charges etc., complete.

Supply and fixing of PVC Conduit/Casing and capping make Standard including all materials and labour charges etc., complete.

Supply and fixing of I/O Full Set-Dual make Legrand including all materials and labour charges etc., complete.

Supply and fixing of 48G Fully managed Switch make TP-Link--SG3452 including all materials and labour charges etc., complete.

Supply and fixing of 48G PoE+ Fully managed Switch make TP-Link--SG2452P including all materials and labour charges etc., complete.

Supply and fixing Gateway for ISP Termination make TP-Link--ER605 including all materials and labour charges etc., complete.

Supply and fixing of WirelessAccess Point make TP-Link--EAP245 including all materials and labour charges etc., complete.

Supply and fixing of Wireless LAN Controler make TP-Link--OC200 including all materials and labour charges etc., complete.

Supply and Crimping of RJ45 Connetors make #Digitally Signed#-Link including all materials and labour charges etc., complete.

Supply and Fixing of 4MP Dome Cameras make CP Plus including all materials and labour charges etc., complete.

Supply and Fixing of 4MP Bullet Cameras make CP Plus including all materials and labour charges etc., complete.

Supply and fixing of 16 CH NVR make CP Plus including all materials and labour charges etc., complete.

Supply and fixing of 8TB Survilance Harddisk make Standard including all materials and labour charges etc., complete.

Supply and fixing of 32"Display for CCTV make LGE--32SM5Jincluding all materials and labour charges etc., complete.

Supply and fixing of 43" Display for Rooms make LGE--43UA831Cincluding all materials and labour charges etc., complete.

Supply and fixing of 55" Display for Suit Rooms make LGE--55UA831Cincluding all materials and labour charges etc., complete.

Supply and fixing of 65" Display for Hall make Legrand LGE-65UA831Call materials and labour charges etc., complete.

Supply and fixing of Analog Telephone Handsets make Beetel M59 including all materials and labour charges etc., complete.

Supply and fixing of10 point Crone make Standard including all materials and labour charges etc., complete.

Supply and fixing of 50 Pair Junction box make Standard including all materials and labour charges etc., complete.

Supply and fixing of EPABX-16Ch with 2 external make Matrix-ETERNITY NENX 416 including all materials and labour charges etc., complete.