Loading
Loading…
Loading…
Tender Value
₹1.3 Cr
EMD Value
₹2.1 L
Closing Date
18 Mar 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
SIGNALPGT
14 conditions · 3 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case the balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
(a) The tenderer must have successfully completed or substantially completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (1) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (2) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (3) One similar work each costing not less than the amount equal to 60% of advertised value of the tender. (b) (i) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender.
Similar nature of work : "Any Signalling or Telecom work" OR "Any Electrical work involving supply and Installation of Lightning and surge Protection or any type of Earthing or Earth leakage detectors in Signalling systems."
4 conditions · 2 needing a document upload
The tenderer shall clearly specify that the tender is submitted on behalf of a partnership firm. The following documents shall be submitted by the partnership firm, with the tender: (i) A notarized copy of the Partnership Deed or a copy of the Partnership deed registered with the Registrar. (ii) A notarized or registered copy of Power of Attorney in favour of the individual to tender for the work, sign the agreement etc. and create liability against the firm.(iii)An undertaking by all partners of the partnership firm that they are not blacklisted or debarred by Railways or any other Ministry /Department of the Govt. of India from participation intenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP in which they were /are partners/members. Any Concealment /wrong information in regard to above shall make the bid ineligible or the contract shall be determined under Clause 62 of the Standard General Conditions of Contract 2022.
Documents to be submitted along with Tender: The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm /Company / Joint Venture (JV)/Registered Society/Registered Trust /HUF etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be. Necessary Documents should be submitted as per GCC April 2022
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The rates quoted by the tenderer should be inclusive of all taxes including GST.
Improvement of Safety in S&T Installations through provision and protection of cables, additional earthing arrangements, Earth Leakage Detectors throughout Palakkad Division.
J-SG-OT-25-2025-629761
J-SG-OT-25-2025-629761
Open
Works - General
9 Months
Palakkad, Kerala
₹0
₹2.1 L
18 Mar 2026
23 Feb 2026
4 Mar 2026
71 items across 2 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | 1300.00 | — | — | ||
| Wiring o f Relay Inputs t o Wago Block and Wago block to Datalogger. Necessary Wagos required is included as per schedule | — | — | — | 5,35,278.57 | |
| — | 30.00 | — | — | ||
| Provision of earth electrodes as per drawing No.SG/CN/02/13 and earthing of metallic sheath and armour of all cables in all apparatus cases, relay room, equipment room, SM's room for block and control, and earthing of all equipments in apparatus cases, power room, relay rack, cable termination rack, control panel, signals, lever frames with MS flat 35mm X 6mm/19c cable (MS flat for closer by areas and MS flat/19c cable combination for farther areas) as per the instructions of Railway representative at site. The work includes painting of earth resistance value on the earth pit. (Supply of 19C cable is not covered in the scope of this schedule). [MS flat for earthing 35mm X 6mm, cement, GI earth electrodes, common salt, charcoal, country bricks, M sand, soldering materials and all other miscellaneous materials required for the work shall be supplied by the Contractor]. | — | — | — | 73,786.65 | |
| — | 5.00 | — | — | ||
| Supply of 8-Channel RDSO/SPN/256/2002 or latest | — | — | — | 7,97,686.75 | |
| — | — | — | RDSO | ||
| — | — | — | Specifications | ||
| — | 5.00 | — | — | ||
| S u p p l y o f 12-Channel E a r t h Leakage RDSO/SPN/256/2002 or latest | — | — | — | 10,86,362.14 | |
| — | — | — | D S O Specifications | ||
| — | 30.00 | — | — | ||
| S u p p l y o f 16-Channel E a r t h Leakage RDSO/SPN/256/2002 or latest | — | — | — | 73,46,904.24 | |
| — | — | — | D S O Specifications | ||
| — | 5.00 | — | — | ||
| Installation o f 8-Channel Earth Leakage Detector. This includes transportation of materials to Site location and provision of cable trough arrangements including connection to the BRC earth. Also includescarrying out of pre-commission checklist. | — | — | — | 81,526.64 | |
| — | 5.00 | — | — | ||
| Installation o f 12-Channel Earth Leakage Detector. This includes transportation of materials t o Site location and provision of cable trough arrangements including connection to the BRC earth.Also includes carrying out of pre-commission checklist. | — | — | — | 98,850.04 | |
| — | 30.00 | — | — | ||
| Installation o f 16-Channel Earth Leakage Detector. This includes transportation of materials t o Site location and provision of cable trough arrangements including connection to the BRC earth. Also includes carrying out of pre-commission checklist. | — | — | — | 7,59,955.18 | |
| — | 500.00 | — | — | ||
| Supply o f 2 4 Core x 1.5 Sq.mm PVC insulated Armoured, unscreened underground Railway Signalling copper cable as per IRS: S-63/2014 REV.4 | — | — | — | 2,79,545.63 | |
| — | 500.00 | — | — | ||
| Supply of 12Cx1.5 SQMM PVC insulated Armoured, unscreened underground Railway Signalling copper cable as per IRS: S-63/2014 REV.4 | — | — | — | 1,55,505.58 | |
| — | 500.00 | — | — | ||
| Excavation of cable trench in all kinds of soil except hard rocky areas including clearing of roots of trees, rocks, bushes etc. to a depth of 1.0 Mtrs and to a width of 0.3 Mtrs. (Laying of cables is not included in this schedule) | — | — | — | 46,164.82 | |
| — | 120.00 | — | — | ||
| Excavation of trench to a depth of 1 Mtr. for track crossing of cables, refilling of trench by ramming and consolidating it as per the instructions of Railway representative at site after laying of DWC/RCC pipes. During excavation of trench, it has to be ensured that the excavated soil does not mix with the ballast available. The depth of 1m trench shall be from the bottom of sleepers for track crossings. Laying o f cables a n d DWC pipes is not included in this schedule. (Supply of DWC/RCC pipes with couplers/collars is not included in this schedule). | — | — | — | 66,624.26 | |
| — | 60.00 | — | — | ||
| Provision of GI pipes (50/100mm dia) for cable laying with offset at both ends and with couplings over RCC bridges, drainage, culverts, and girder bridges. For RCC bridges, drainage, and culverts, the pipes shall be mounted on concrete masonry supports of size 300mm x 300mm x 300mm at an interval of 2 meters. For girder bridges, the pipes shall be fixed on suitable MS clamps at an interval of 2 meters. The ends of the pipes shall be closed with brick masonry abutments to ensure that no cable is exposed. The work shall be carried out as per the instructions of the Railway representative at the site.(Supply of GI pipes with couplings and laying of cables is not included in this schedule).Stone jelly (20/25mm size), bricks, sand, cement, MS angles, flats, bolts, nuts for manufacturing and fixing clamps, bricks, M sand, cement, and other miscellaneous materials for the work shall be supplied by the contractor. | — | — | — | 18,022.86 | |
| — | 1000.00 | — | — | ||
| Laying o f signaling/power/ telecommunication cables a s p e r cable plan in cable trenches, masonry ducts, RCC Pipes, DWC pipes, GI Pipes etc.(Supply of cables is not included in this schedule). | — | — | — | 26,186.47 | |
| — | 500.00 | — | — | ||
| "Refilling of cable trench 1m depth by 0.3m width throughout, with earth after laying of cables, and consolidating the trench by ramming and levelling." | — | — | — | 11,091.08 | |
| — | 60.00 | — | — | ||
| "Road crossing/ Track Crossing through Horizontal Drilling at approximately depth of 1.5 to 2m below the formation level of the earth including insertion of HDPE pipe/DWC pipe along with couplers, drawl of cable (or) direct drawl of cables etc. (Note: The pilot used for HDD should be of sufficient size to suit insertion of HDPE /DWC pipe of size 120mm (outer dia.) or direct drawl of three cables (Signalling/Power/Quad/OFC) or three nos.of 4 0 m m d i a H D P E p i p e o r a n y other combination as directed by the site engineer) ( Supply of HDPE pipe is not covered in this schedule)" | — | — | — | 1,16,797.71 | |
| — | 200.00 | — | — | ||
| Fixing o f PBT terminal block/ PBT fuse block, rubber grommets, clamping of cables using teakwood cable clamps and base planks, termination of cables, provision of ND type fuses of required capacities, provision of copper bus bar for supply terminals, wiring, provision of termination particulars diagram board using plywood of thickness 12mm - teakwood finish o f size 1800mm x 1200mm with Aluminium grooved channel frame in the relay room. The blank spaces over the top of the cable termination rack shall be covered with phynolic sheet of thickness 3mm wherever required. The termination and cable core particulars shall be painted on the PVC/ nylon sleeves. The work also includes identification of cables using aluminium tags provided on each cable with letters punched neatly.(Supply of PBT terminal blocks 25mm & 60mm centers and PBT Fuse blocks is not covered in the schedule) [Wire P V C 3/0.75mm copper, brass bolts and n u t s a n d washers, f o r fixing PBT terminal/Fuse Block, other fixing bolts and nuts, rubber grommets, PVC/ Nylon sleeves, copper bus bars, teakwood 50mm x 50mm for cable clamps, 25mmx 100mm for base planks, phynolic sheet 6mm thick of size 1200mm x 1800mm with aluminium grooved channel frame, phynolic sheet 3mm thick, paint and all other miscellaneous materials shall be supplied by the Contractor]. a)Fixing of PBT terminal blocks (25mm/60mm centre) and termination (Per Unit = Per Terminal Block) | — | — | — | 48,394.56 | |
| — | 50.00 | — | — | ||
| Fixing o f PBT terminal block/ PBT fuse block, rubber grommets, clamping of cables using teakwood cable clamps and base planks, termination of cables, provision of ND type fuses of required capacities, provision of copper bus bar for supply terminals, wiring, provision of termination particulars diagram board using plywood of thickness 12mm - teakwood finish o f size 1800mm x 1200mm with Aluminium grooved channel frame in the relay room. The blank spaces over the top of the cable termination rack shall be covered with phynolic sheet of thickness 3mm wherever required. The termination and cable core particulars shall be painted on the PVC/ nylon sleeves. The work also includes identification of cables using aluminium tags provided on each cable with letters punched neatly.(Supply of PBT terminal blocks 25mm & 60mm centers and PBT Fuse blocks is not covered in the schedule) [Wire P V C 3/0.75mm copper, brass bolts and n u t s a n d washers, f o r fixing PBT terminal/Fuse Block, other fixing bolts and nuts, rubber grommets, PVC/ Nylon sleeves, copper bus bars, teakwood 50mm x 50mm for cable clamps, 25mmx 100mm for base planks, phynolic sheet 6mm thick of size 1200mm x 1800mm with aluminium grooved channel frame, phynolic sheet 3mm thick, paint and all other miscellaneous materials shall be supplied by the Contractor]. b)Termination using PBT fuse block in cable termination rack (Per Unit = Per Fuse Block) | — | — | — | 14,495.47 | |
| — | 6.00 | — | — | ||
| Supply of Fiber Visual Fault Locator with accessories, as per Technical specification | — | — | — | 1,47,871.46 | |
| — | 200.00 | — | — | ||
| Supply o f PBT terminals 25mm/ 60mm centre and PBT Fuse blocks with necessary inspection a s p e r specification/ drawing/ description enclosed in this document. a)Supply of PBT terminals 25mm centre. | — | — | — | 17,699.64 | |
| — | 100.00 | — | — | ||
| Supply o f PBT terminals 25mm/ 60mm centre and PBT Fuse blocks with necessary inspection a s p e r specification/ drawing/ description enclosed in this document. b)Supply of PBT terminals 60mm centre. | — | — | — | 13,398.6 | |
| — | 50.00 | — | — | ||
| Supply o f PBT terminals 25mm/ 60mm centre and PBT Fuse blocks with necessary inspection as per specification/ drawing/ description enclosed in this document. c)Supply of PBT fuse block without ND fuse | — | — | — | 7,478.56 | |
| — | 180.00 | — | — | ||
| Supply o f Double walled corrugated pipe - 103.5mm inner dia & 120mm outer dia conforming to specification No. IS 14930(Part 2): 2001 with one coupler for every 6m of pipe as per Technical specification | — | — | — | 94,683.54 | |
| — | 60.00 | — | — | ||
| Supply of GI pipes - 100mm dia-4.5mm thick as per Technical specification | — | — | — | 96,722.28 | |
| — | 200.00 | — | — | ||
| Termination o f n e w main/tail cables o n the existing terminals/ fuse blocks in apparatus cases/ battery boxes/ CT boxes/ cable termination racks as per approved circuit diagram. The terminal particulars a r e to be repainted /corrected o n t h e doors of apparatus cases/ battery boxes/ cable termination boxes and FTOT index board as instructed by Railway representative at site. This work includes closing the opening created for entry of new cables i n the apparatus cases with masonry brick work and sealing the bottom of the apparatus cases/ cable termination racks with cable compound.[Paints, wire PVC 3/0.75mm and 16/0.2mm copper, sealing compound, bricks, cement, M sand and all other required miscellaneous materials shall be supplied by the contractor]. (Per Unit = Per Terminal block) | — | — | — | 21,199.81 | |
| — | 120.00 | — | — | ||
| Laying of DWC/Split DWC Pipes for Track Crossing/Road Cutting/Trenches | — | — | — | 7,339.13 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCC_April-2022.pdf
ATTACHMENT
GCCcorrectionslip1to4.pdf
ATTACHMENT
GCCcorrectionslip5TO10.pdf
ATTACHMENT
AnnexureV.pdf
ATTACHMENT
AnnexureVA.pdf
ATTACHMENT
AnnexureVIB.pdf
ATTACHMENT
JPOfordiggingwork.pdf
ATTACHMENT
SOR2022.pdf
ATTACHMENT
TDELDNEW230226_1.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .