Balance work for the Construction of Sushruta Bhawan-II (2BHK Flats (24 Nos)

Amount

CIVIL ITEMS (Excluding Cost of All Material)

a) Earthwork in bulk excavation in all kinds of soil by mechanical means (hydraulic excavator) over areas exceeding 30 cm in depth, 1.5 mts in width as well as 10 sqm on plan including disposal of excavated soil upto a lead of 1 km (As directed by the Engineer-Incharge).

b) Earthwork in bulk excavation in all kinds of soil by mechanical means (hydraulic excavator) over areas exceeding 30 cm in depth, 1.5 mts in width as well as 10 sqm on plan including disposal of excavated earth lead upto 50 mtr. (Complete job).

Labour for laying in position cement concrete in 1:4:8 (1cement:4 Coarse Sand :8 Crushed Stone Aggregate 40 mm nominal size) excluding cost of centering and shuttering for all works up to plinth level , including all leads and lifts complete.

Labour for laying Reinforced cement concrete (1:2:4) 1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size(or any mix) in walls (any thickness) including attached pilasters, buttresses, beams, column, slab etc excluding the cost of centering shuttering, finishing and reinforcement including all leads & lifts complete.

Labour for laying reinforcement for RCC work including straightening, cutting, bending, placing in position and binding including cost of binding wires and all leads & lifts complete.

Labour for brick work with common burnt clay F.P.S (non modular) bricks of class designation 75 in foundation, plinth and upto all floor levels in cement mortar 1:6 (1 Cement : 6 Coarse Sand) including all leads & lifts complete.

Labour for half brick masonry with F.P.S bricks of class designation 75 for all floor levels including laying of RCC bands (M15) with nominal reinforcement at every one mtr. height of masonry in cement mortar 1:4 (1cement :4 coarse sand), including all leads & lifts complete.

Labour for re-handling of available excavated earth (excluding rock) for filling in trenches, plinth, sides of foundations etc in layers not exceeding 20 cm in depth consolidating each deposited layer by hand held vibro compactor, ramming and watering, lead upto 50Mt & lift upto 1.50M.

Providing and fixing of formwork of timber planking, steel plates. Ply board sheets etc so as to give rough finish including centering, shuttering, strutting, propping complete upto all levels and removal & stacking of the same, complete job.(including cost of shuttering, T&P & Sundries.)

a) Foundations, footings, bases of columns.

b) Walls (any thickness) including attached pilasters, buttresses & courses etc.

c) Suspended floors, roofs, landings, balconies, access platforms

Labour for hand packed Stone soling under floors of the rooms/plinth sides including all leads & lifts complete.

Labour for laying plain cement concrete flooring 40 mm thick in 1:2:4 mix (1 cement:2 Coarse Sand: 4 Crushed Stone Aggregate 20 mm nominal size) with a floating coat of neat cement slurry including all leads & lifts complete.

Labour for 6mm thick cement plaster in 1:3 (1 cement : 3 fine sand) for ceilings at all floor levels including all leads, lifts & scaffolding complete.

Labour for 15 mm cement plaster in1:6 (1 cement : 6 fine sand) on rough side of single/half brick walls (internal plastering) including cutting grooves in junction between RCC and brick masonry at all floor levels including all leads, lifts & scaffolding complete.

Labour for 25 mm thick cement plaster in two coats, backing coat 15 mm thick & finishing coat 10 mm thick on fair side of single/half brick walls (external plastering) including cutting grooves in junctions between RCC and brick masonry in cement mortar 1:4 (1 cement : 4 fine sand) up to all floor levels including all leads, lifts & scaffolding complete.

Labour for applying white cement based putty of average thickness 2mm of approved brand and manufacture, over the plastered wall surface (internal & external) to prepare the surface even and smooth complete at all floors levels including all leads, lifts & scaffolding complete.

a) Internal Surface

b) External Surface

Labour for applying one coat of water thinable cement primer of approved brand and manufacture on prepared wall surface of internal walls at all floor levels including all leads & lifts complete.

Labour for wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ltr of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour at all floor levels (Two Coats).

Labour for finishing wall with premium acrylic smooth exterior paint with silicone additives of required shade on New work (two or more coats applied @ 1.43 ltr/10sqm over and including base coat of water proofing cement paint applied @ 2.20kg/10sqm) at all floor levels complete. As per the shades as directed by Engineer-in-charge.

Labour for Steel work welded in buildup sections framed work including cutting, hoisting, fixing in position complete including the cost of welding rods and all leads & lifts complete

Labour for laying glazed/polished vitrified floor tiles of any size (as per required thickness) in the pattern as approved by Engineer-Incharge laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigment etc. complete at all floor levels including all leads & lifts complete.

Labour for fixing 18mm thick granite gang saw cut mirror polished (pre moulded and pre polished), machine cut for kitchen platform, vanity counters window sills facias and similar locations of required size laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all floor levels, including all leads & lifts complete.

Extra Labour for providing edge moulding to 18mm thick Granite counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge, including all leads & lifts complete.

Grinding/Polishing of marble/granite floors with wax polish where ever required as directed by the Engineer-in-charge.

Labour for 18mm thick Granite Work gang saw cut (polished and machine cut) for wall lining (veneer work) in cement mortar 1:3 (1 cement:3 coarse sand) including pointing with white cement mortar 1:2 (1 white cement:2 marble dust) with an admixture of pigment to match the granite shade at all floor levels with all leads & lifts complete. (To be secured to the backing by means of clamps).

Labour for laying in position plain cement concrete 1:3:6 (1 cement:3 coarse sand : 6 crushed stone aggregate 40 mm nominal size) excluding cost of centering and shuttering all works upto plinth level, including all leads & lifts complete.

Labour for making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement:3 coarse sand :6 crushed stone aggregate 20 mm nominal size) over 75 mm bed of dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth including all leads & lifts complete.

Labour for laying 80mm thick factory made antiskid, anti glazed PCC Interlocking paver blocks of shade and pattern to be approved by Engineer-Incharge over 50mm thick compacted bed of naturally occurring, clean, well graded, sharp coarse sand (passing 4.75mm sieve) of uniform moisture content 4% to 8% at the time of spreading. Paver units should be placed with the help of spacer (2mm - 3mm wide) on un-compacted sand and cutting machine, filling the spaces between 25mm and 50mm wide concrete having minimum 1:1:2 cement : sand : 20mm crushed stone aggregate mix. After laying paver blocks they shall be compacted with high frequency, low amplitude mechanical flat plate vibrator having plate area sufficient to cover a minimum of 12 paving units, after compaction joint filling by sand shall be spread over the pavement (Joint filling sand shall pass a 2.36 mm No. 8 Sieve) and complete as per direction of Engineer-in-charge including all leads & lifts complete.

PLUMBING & SANITARY WORKS (EXCLUDING COST OF MATERIAL) Labour for fixing on surface/ wall face UPVC rain and sewer pipes including jointing with leaving 10 mm gap for thermal expansion (i) single socketed pipes along with all required fittings like tees, bends, crosses with or without access doors jointed with approved solvent cement as per manufacturer's recommendations, fixed to walls and ceilings with clamps complete including cutting and making good the walls and ceilings where required complete as per direction of Engineer in Charge.

250 mm outer dia ( 6 KG PRESSURE/ cm2)

200 mm outer dia ( 6 KG PRESSURE/ cm2)

110 mm outer dia ( 6 KG PRESSURE/ cm2)

Labour for fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SDR 7.4 UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings I/C trenching, refilling and testing of joints complete as per direction of Engineer-in-charge. (External work)

PN-16 pipe, 25mm OD

PN-16 pipe, 40mm OD

PN-16 pipe, 50mm OD

PN-16 pipe, 75mm OD

PN-16 pipe, 90mm OD

Labour for fixing, Testing & Commissioning of full way lever operated PPR Ball Valves tested to a high pressure rating (at all floors).

Labour for fixing Heavy class SS grating (SS 304) grade with Cockroach proof SS strainer of approved design including setting in floor with cement motor to match with floor finish as per architect requirement suitable for waster FD & FT (at all floors). Size: 110mm dia

Labour for fixing Heavy class M.S. grating of required pattern for rain water outlets at terrace including cutting and making good the floor with cement mortar mixed with water proofing compound. Size 150 mm dia

WC cum Bathroom fitting complete inside the periphery of Toilet, fitting of taps, washbasin, washbasin mixer, European seat cistern, shower, towel rail, towel ring, looking glass, glass shelf, CP grating and soap dish, geyser, gratings, angle valve etc and testing of the system complete.

Labour for fixing Salem stainless steel A ISI 304(18/8) Kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40mm incl. PVC flexible waste pipe, waste fittings, C.P. brass coupling and C.P. Brass grating with hole of required dia incl. Painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink without drain board 610x460 mm bowl depth 200 mm

Labour for fixing, testing & commissioning of C.P. brass wall mounted sink mixer with C.P. wall flange, overhead swinging spout complete as required and making good all necessary wall cutting / chasing complete as per direction of Engineer in Charge.

Labour for fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931 a) 15 mm nominal bore.

Labour for fixing of C.P. Brass soap dish

Labour for fixing C.P. brass Towel ring.

Labour for lifting, placing and fixing on terrace (at all floor levels) polyethylene water storage tank with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes and with T fittings and construction of base support for tanks complete job including testing of joints. a) 5000 ltr capacity Tripple layer

Labour for unloading, handling, storage /stacking of

a) Cement

b) Steel

c) Granite/Tile

d) UPVC/PPR Pipes & Fittings

e) Chinaware & CP Fittings

f) Polyethylene Water Storage Tanks

katyal construction company

ABROL INFRASTRUCTURES