Provn of two toilet blocks for patients of family ward and hospital lab at MH Kannur under AGE (I) Cannanore

Amount

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft loose soil all as specified and directed.

Excavations in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for foundation or for shafts, wells, cess pits, manholes, pier holes, UG cable, pole etc not exceeding 10 sqm on plan and not exceeding 1.50m in depth and getting out hard / dense soil all as directed.

M & L for plain cement concrete (1:4:8), type D2 using 40 mm graded stone aggregate as in foundation of building, pole, strut, stay etc all as specified and directed.

M&L Cutting openings through walls for door, window and other openings or enlarging existing openings, etc., or cutting out defective masonry for underpinning including providing fixing and removing, shoring, cleaning and stacking stone and removing surplus to store and rubbish off the premises old masonry built in cement mortar all as specified and directed.

M&L for laterite stone masonry, regular coursed, well bonded and solidly hearted , built in CM (1:6) all as specified and directed.

M&L Reinforced cement concrete (1:1.5:3), type A1, (using 20mm graded stone aggregate) nominal mix as in beams, lintel over 1.5m span all as specified and directed. Note : Reinforcement and form work shall be measured and paid separately.

M&L Reinforced cement concrete (1:1.5:3), type A1, (using 20mm graded stone aggregate) nominal mix as in roof slab supported on wall, beam and column and like all as specified and directed. Note : Reinforcement and form work shall be measured and paid separately.

M&L for use and waste of form work to sides and soffits of lintel, beams etc rough finished surface of concrete all as specified and directed.

M&L for use and waste of form work to soffits of suspended slabs such as roof slab (horizontal or sloped) floor slab etc n exc 200mm thickness rough finished surface of concrete all as specified and directed.

M&L for use and waste of form work to edges of concrete flat, treads etc similar work exc 10cm but n exc 20cm wide for rough finished concrete surface all as specified and directed.

S&F TMT bars 10 mm dia and over as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips all as specified and directed.

S&F TMT bars 6 to 8mm dia as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips all as specified and directed.

M&L for providing pre-cast cement concrete block masonry with solid blocks, exc.10cm in width with PCC (1:3:6), type C1, using 20mm graded stone aggregate and set in cement mortar (1:6) complete all as specified and directed.

M&L for providing pre-cast cement concrete block masonry with solid blocks, 10cm thick with PCC (1:3:6), type C1, using 20mm graded stone aggregate and set in cement mortar (1:4) complete all as specified and directed.

Filling in floors or pavings, laid in layers n. exc. 25 cm thick, spread, levelled and rammed including watering using excavated earth obtained from item No 1&2 here in before all as specified and directed.

M&L for hard core of guage n.exc 63mm broken stone or boulders, deposited, spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface all as specified and directed

M&L 75mm thick PCC 1:4:8 Type D2 (using 40mm graded stone aggregate) as in sub base of floor and paving including necessary form works all as specified and directed.

M&L for 25mm thick, PCC (1:2:4) type B0,using 12.5mm graded stone aggregate as in floor finished even and smooth using extra cement all as specified and directed.

M&L chequered cement concrete tiles, 200x200x25mm thick set, jointed and pointed in neat cement slurry in floor with grey cement and no pigments including 20mm thick screed bed or bedding layer in cement mortar (1:4)all as directed.

M & L for moorum/red bajri filling in floors or pavings, laid in layers n. exc. 15 cm thick, spread, levelled and rammed including watering all as specified and directed.

M&L for coloured non-skid ceramic tiles, 7-8mm thick, area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match including 20mm thick screed bed or bedding layer in cement mortar (1:4) all as specified and directed.

M&L for coloured glazed ceramic tiles 7 to 8mm thick area of each tile exc 0.06 but n exc 0.16Sqm, as in skirting / dado, set and jointed in neat cement slurry and pointed in coloured / white cement to match including backing coat of 10mm thick in cement mortar (1:4) all as specified and directed.

M&L 75mm thick PCC 1:3:6 Type C2 (using 40mm graded stone aggregate) as in plinth protection and paving including necessary form works finished even and fair at top without using extra cement all as specified and directed.

M&L for rendering 10mm thick in cement mortar (1:6) on concrete surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 15mm thick in cement mortar (1:4) on concrete surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 5mm thick in cement mortar (1:3) on ceiling surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 15mm thick in cement mortar (1:4) on RCC roof concrete surfaces with WPC as per manufacturer's instructions, finished even and smooth without using extra cement all as specified and directed . Note: WPC shall be measured and paid seperately.

Supply only water proofing compound.

M & L for water proofing treatment to RCC roof with APP modified water proofing membrane of 4mm thick and weight not less than 4.00 Kg per Sqm reinforced with non woven polyster matt (weighing not less than 160gms/sqm) having softening point not less than 140 degree centigrade, longitudinal tensile strength not less than 800N/sqcm tearing strength of 180Nm by torch application including minimum 10cm side overlap and 15cm end lap over a coat of oil based bitumen primer @ 0.2Kg/sqm and finishing with solar reflective bituminous aluminium paint @ 100gms/sqm all as specified and directed.

S&F powder coated anodised aluminium frame for doors, windows, ventilators, with one or more rebates including joining cleats for fixing etc, complete all as specified and directed. Note:- Thickness of powder coating shall be 50 micron

S&F powder coated aluminium window and ventilator shutter side hung type without sash bars of approved colour with aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, aluminium snap beading, screws, aluminium fittings such as peg stay 150mm long 1 Nos, hinges 100mm type B21 2Nos, suitable handles 1 Nos in each shutter complete all as specified and directed. Note:- Thickness of powder coating shall be 50 micron

S&F 3mm thick plain sheet glass but one side frosted, glazing with oil putty in squares not exc 0.50 Sqm in each pane all as specified and directed.

M&L solid PVC door frame of sizes 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, all as specified and directed.

S&F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain coloured PVC “C” channel having a PVC sheet strip of 20mm width stock inside with solvent cement for stiles and plain colour PVC sheet for top rails, lock rails and bottom rails on either side and as gap insert for top rail & bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour of PVC sheet fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement etc. Details as peer specification and drawings and all as directed.

S&F stainless steel butt hinges medium weight; 100mm size all as specified.

S&F 150mm long aluminum anodized barrel tower bolts of extruded section all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 150mm size all as specified.

M&L for preparation of new plastered wall surfaces and applying 3 coats of white wash all as specified and directed.

M&L for preparation of new plastered ceiling surfaces and applying 3 coats of white wash all as specified and directed.

M&L for preparation of new plastered surfaces and applying 2 coat of cement base paint over a coat of primer on walls surfaces all as specified and directed.

S&F Vitreous China Wash down water closet pan (Pedestal pattern) white, (excluding flushing cistern and flush type) pedestal pan and trap including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe, etc complete including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device of Economical type of make Jaguar or equivalent in Cera/Parryware all as specified and directed.

S&F for PVC valveless, syphonic action type flushing cistern low level, 10 Litre capacity, white, with inlet, ball valve, float and handle including flush pipe all as specified and directed.

S&F 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as specified and directed.

Supply and fix PVC connecton 45cm long with brass sockets both ends for flush tank, wash basin, etc. all as specified and directed

S & F PVC (SWR) P trap plain including jointing with solvent cement ,125/110mm bore all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement all as specified and directed.

S&F 110mm bore, PVC (SWR) bend any radius with solvent cement joints all as specified and directed

M&L for 110mm bore PVC (SWR) junction single T (equal or unequal) including jointing with solvent cement all as specified and directed.

M&L PVC (SWR) pipe 75mm bore single socketed with solvent cement joints laid in floor or trnches all as specified and directed.

M&L PVC (SWR) pipe 75mm bore single socketed with solvent cement joints fixed to wall all as specified and directed.

S&F 15mm pillar taps cast copper alloy with capstan heads, chromium plated , screwed down high pressure ,with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed all as specified and directed.

S & F stop valve 15mm bore, chromium plated, cast copper alloy, screwed down high pressure with crutch or butterfly handle all as specified and directed.

S&F Vitreous China Wash basin, white, flat back, size 580 x 450 mm, including CI brackets, waste pipe etc. (but excl. pillar tap) cutting for and pinning in ends of brackets or erecting stand and fixing of waste pipe etc complete all as specified and directed.

S&F for 15mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings or in floors etc. all as specified and directed.

S&F for 20mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed to wall/ceiling or on floor all as specified and directed.

S&F 500 litres capacity rotational moulded polthylene water storage tanks(cylindrical vertical with closed top) of make Sintex/Polycon/Plasto hoisted and fixed in position including 15mm dia bore ball valve brass high pressure with polythene float and fly nut complete screwed for UPVC pipe all as specified in SSR Part I,2009 and directed.

S&F bib tap 15mm dia, chromium plated, fancy type, cast copper alloy, screwed down, screwed for iron pipe or ferrule and complete all as directed.

S & F PVC (SWR) floor trap plain with grating including jointing with solvent cement ,75mm bore all as specified and directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 including one shop coat of zinc chromite primer at contractors workshop before fabrication all as specified and directed.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

M&L preparing new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of red oxide primer all as specified and directed.

M & L for cement concrete (1:2:4), type B1 (using 20 mm graded stone aggregate) as in benching, stops of manholes, coping etc including weathering, slightly rounded or chamfered angles and throating all as specified and directed.

M&L for Pre-cast RCC (1:2:4) type B1 using 20mm graded stone aggregate as in manhole/soak well/drain cover slab etc; set in cement mortar (1:6) all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:4) on concrete surfaces, using WPC finished even and smooth without using extra cement all as specified and directed . Note: WPC shall be measured and paid seperately.

M&L PVC (SWR) pipe 160mm bore single socketed with solvent cement joints laid in trenches or in floors all as specified and directed.

M&L PCC (1:3:6) type C2 (using 40mm stone aggregate) concrete bed to drain pipe 160 mm bore including packing under and haunching against the sides of pipe after they are laid and tested all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel ( ½ round or ¾ section) in cement concrete 1:2:4, type B1 using 20mm graded stone aggregate, smooth finished and reforming benching as required for internal dia of pipe 160mm ball as directed.

Returning and filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick with soil obtained from excavation all as directed

Removing surplus excavated materials (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and directed.

M&L Point wiring complete with 1.5 Sq mm single core PVC insulated unsheathed copper conductor FRLS cable multi stranded 1100 Volt grade drawn through and including non metallic rigid PVC conduit concealed to wall fixed to ceiling/roof etc with necessary fixing accessories such as bend elbow socket etc with fixing material including terminal box made out of 1.22mm thick MS Sheet concealed in wall covered with laminated sheet top cover of 3 mm thick cadmium plated screws with cup washer for housing switches, switch socket out let, regulator etc including 1.5Sqmm single core PVC insulated un sheathed copper conductor FRLS cable multi stranded 1100Volt grade as earth continuity conductor green in colour connected to common earth dolly complete all as specified and as directed for One light/fan/bell point controlled by one switch.

S & F switch piano flush type, single pole, one way, 5 Amps, 240 volt including connecting up electrically complete all as specified and as directed.

S & F PVC ceiling rose round shape, three terminals, polycarbonate, isolated body including connecting up electrically all as specified and as directed.

S & F sheet metal enclosure factory made for MCB DB, SPN 4 way with 200 Amps bus bar, 240 Volt, double door type, fixed/flushed on wall including electrically connecting up complete all as specified and directed.

S & F MCB SPN, 240 Volt, 5 to 32Amps including electrically connecting up using wiring lugs all as specified and directed.

S & F MCB SP, 240 Volt, 6 to 32Amps including electrically connecting up using wiring lugs all as specified and directed.

S&F decorative ultra slim linear LED light fittings with extruded Aluminium, heat sink, environmental friendly, energy efficient ready to use pack of ELITE LED OF 10W LED 6000K. Model LHEXBYPNIN1W010 of Havells or equivalant of Bajaj/Crompton Greaves and electrically connecting up all as directed.

Supply and spreading in trenches with fine dry river sand for cushioning of cable and compacted in layers all as specified and directed. Note :- Punned thickness shall be measured / paid.

Supply and laying Best quality, locally available, sub class ‘B’ bricks (Old Size) for cable protection cover, laid flat and dry in trenches over the cable , perpendicular to the direction of cable complete all as specified and as directed by Engineer-in-Charge.

S&F 40 mm bore Galvanised iron tubing, light grade, with all fittings laid in trenches, floors, road crossing, fixed to pole/wall etc as required protection of UG cables/GI strip complete all as specified and as directed.

Supply and lay including fixing and connecting electrically XLPE insulated LT underground cable 2core 10 sqmm , armoured heavy duty electric cable with aluminum conductor multi-stranded 1100 volts grade, laid in trench, fixed on wall/pole drawn through pipe etc including provision of lugs & testing of following sizes complete all as specified and directed. Note : Excavation shall be measured and paid seperately. Quoted rate include of making connection to LT panel/feeder pillar box/junction box through suitable size aluminium lugs and cable glands.

S&F for 25mm bore UPVC pipes of pressure rating 10 kgf / cm2, laid in trenches including all fittings required all as specified and directed.

S & F Gun metal globe or gate valve 25mm bore with iron wheel head ,screwed both ends for UPVC pipes and fixed complete including taking out old unserviceable valve all as specified and directed.

Supply & fix exhaust fans, plastic body AC single phase 230/240 V size 200mm sweep of make Havells/CG/Philips with louver including making suitable hole connecting electrically complete and all as directed.

JEETH CONSTRUCTION