CA NO. CWE BLY / GE(E)/ 45 OF 2021-2022 PROVN OF 01 X STORE SHED (10 X 10 MTRS) OF CBRN AND QRMT EQPT STORE UNDER GE(E) BAREILLY

Amount

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation etc. or for manholes, cesspits, shafts etc. not exc. 10 Sqm on plan and getting out in any type soil complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Removing excavated soil to distance n.exc. 50m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M&L for providing Plain Cement Concrete, type D-2, 1:4:8 Mix (using 40 mm graded stone aggregates) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for RCC M25, Design mix (Using 20mm graded stone aggregates) as in foundations, including raft, footing, foundation beam, under reamed piles and mass concrete complete all as specified and directed.

M&L for RCC M25 Design mix (Using 20mm graded stone aggregates) as in beams, lintel beams over 1.50 meter span,cantilevers, bressummers etc complete all as specified and directed.

M&L for RCC M25 Design mix (Using 20mm graded stone aggregates) as in Chajjas complete all as specified and directed.

M&L for RCC M25 Design mix (Using 20mm graded stone aggregates) as in columns, piers, posts etc complete all as specified and directed.

M&L for RCC M25 Design mix (Using 20mm graded stone aggregates) as in slabs supported on walls, beams and columns in floor, roof, landing, balconies etc complete all as specified and directed.

M&L for Providing Plain Cement Conrete, type B-1, 1:2:4 mix (using 20mm graded stone aggregates) in lintels upto 1.5m clear span, cills, steps, seismic, and other similar bands, plinth courses, string courses, lacing courses parapets and railing up to 60 cm in height, copings, benching, kneelers, apex, stone bed plates water troughs and the like including weathering slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders , cut to length , bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified.

M&L for use & waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finishedsurfaces of concrete complete all as specified and directed.

M&L for use & waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work n.exc. 200 mm thick curved (horizontal or sloping ) work for fair finished flat surfaces of concrete complete all as specified and directed.

M&L for use & waste of form work to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers, lintels, cantilevers, shelves including supports,overhangs, etc. also splays between floors and beams, etc.for fair finished surfaces of concrete complete all as specified and directed.

M&L for ues & waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for fair finished surfaces complete all as specified and directed.

M & L for treating the bottom and sides of excavation at the rate of 5 ltr of emulsion per square meter of surface area for Pre-construction anti-termite treatment complete all as specified and directed.

M & L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

M&L for brick work with fly ash bricks straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

S&F Steel windows with pressed steel frame (dimension- 95X45X1.25 mm ),side hung shutters including box type hinges with steel handle, and steel peg stay, complete with Glazed openable shutter with glazing bars (out side shutters) and wire gauged openable shutter without glazing bars ( inside shutter),dovetailed or welded complete all as specified and directed all as per Drg No- TD/088 dt 07 Jan 2002.

S&F steel ventilators, bottom portion fixed type glazing and top portion with top hung wire gauze shutter dovetailed or welded complete all as specified and directed.

S&F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framedguard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F 3mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.4mm, fixed with stainless steel wire staples complete all as specified and directed.

S&F for 2nd class hard wood Plain, solid, straight chowkats and frames for double shutter, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

M&L for Glazed and skeleton shutter, 35 mm thick of 2nd class HW(SAL), open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc. Size of members of shutter as specified in SSR Pt-I, section 8, clause 8.24(a) supplied & filled to chowkhats complete all as specified and directed.

M & L for 2nd class hardwood,40mm thick factory made Plain framed, panelled shutters (two panel) withlock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F butt hinges, 100 mm, type C-21, of extruded aluminum alloy with galvanized mild steel hinges pin anodized and fixed complete all as specified and directed.

S&F aluminum handles cast type, anodized of 150 mm size complete all as specified and directed.

S&F aluminium alloy, anodized sliding door bolt of 300mm length with hasp and staple (Bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolt of extruded section or cast aluminium alloy complete all as specified and directed.

S&F 200 mm long aluminium anodised , barrel tower bolt of extruded section and fixed all as specified and directed.

M&L for hard core of broken stone of gauge not exceeding 63 mm, deposited, spread & levelled in layers not exceeding 15 cm thick watered and rammed to a true surfaces complete all as specified and directed.

M&L for 75 mm thick, PCC , (1:4:8) mix, type D-2, (using 40mm graded stone aggregates) as in sub base for floor complete all as specified and directed. .

M&L 25 mm thick PCC , (1:2:4) mix, type B1, ( using 20 mm graded stone aggregates ) finished even & smooth with using extra cement as in floor etc. complete all as specified and directed.

M&L for rendering 15mm thick on fair of faces brick work in CM 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M&L Machine cut Kota stone slab 18 mm to 20 mm thick , as in flooring with 18 -20 mm thick and 75 mm wide white marble strip border , laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to give granite finish, over and including screed bed or bedding layer of mortar 15 mm thick in cement mortar (1:6 ) complete all as specified and directed.

M&L for Machine cut kota stone slab 18-20 mm thick as in riser / steps, skirting, dado and pillars laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing over and including 15 mm thick backing coat in CM (1:4) complete all as specified and directed. Note: Kota stone for Risers & Treads of steps shall be in one piece.

M & L for 7 to 8 mm thick, glazed coloured ceramic tiles ( square/ rectangular) of size exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in vertical surfaces such as skirting or dado, set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles including 10mm thick backing coat or bedding layer in cement mortar 1:4 complete all as specified and directed.

M&L for Precast Plain Cement Concrete coloured interlocking paver blocks factory made with casting in rubber/PVC moulds & compacting on a vibro table assembly and shall be cured in curing tank for at least 14 days and then air dried before use. The paver block shall be conforming to IS 15658 -2006 of 60mm thickness, M-35 Grade. approved design, shape, size and colour of top layer laid over & including dry river sand bedding 50 mm thick complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:3:6, type C1,( using 20 mm graded stone aggregates) as in plinth protection, finished the surface even and smooth without using extra cement including forming necessary joints 12 mm wide to the full depth of PCC at every 3 mtr and every change of direction and filling the same with bitumen filler/filler boards 1:3 by weight complete all as specified and directed.

M&L for brushing neat cement slurry over existing roof surface with 3.0kg of cement per sq. metre using liquid water proofing @ 0.15 ltr per 50 kg bag of cement complete all as specified and directed.

Supply only liquid water proofing

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:4, over RCC roof slab for laying water proofing treatment using liquid water proofing @ 0.15 ltr per 50 kg bag of cement laying floor finishes/tiles complete all as specified and directed. Note: Water proofing liquid shall be measured and paid separately.

M&L for rendering 15mm thick on other than fair faces of brick work or concrete (external) surfaces in CM 1:4, finished fair and even without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on fair of faces brick work in CM 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling of fair faces of concrete surfaces and finishing the surfaces even and smooth without using extra complete all as specified and directed.

M&L for applying two coats of Oil bound distemper over a coat of alkali resistant primer including preparation of newly plastered surface of walls complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of chalk whiting primer complete all as specified and directed..

M&L for preparation of newly plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed.

M&L Preparation of New steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint over a coat of red-oxide primer.complete all as specified and directed.

M&L Preparation of new wooden surfaces and applyling two coats of synthetic enamel paint of any description, not otherwise described, over a coat of pink primer complete all as specified and directed.

E/M Part:- M&L for point wiring with 1.5 Sqmm cable PVC unsheathed and insulated copper multistranded conductor FRLS 1100 Volts grade cable (red colour cable to be used for live connection and black colour cable to be used for neutral connection) controlled by one way switch drown through and including PVC concealed conduit with all accessories including 1.0 sqmm copper multistrand conductor FRLS 1100 Volts grade unsheathed PVC insulated (green colour) continuity earth wire connected to common earth dolly and sunk cast pressed steel terminal box made out of MS sheet 1.25 mm thick for mounting of fittings like switch , socket and fan regulator with 3 mm thick hylum laminated sheet cover incl cutting Chases pinning in, for concealed conduit wiring and making goods of disturbed surface not exc 15 cm girth complete all as specified and as directed for one light/fan/bell point controlled by one switch/bell push complete all as specified and directed.

All as per item No 54 above but for 3 pin 5 Amps socket outlet point controlled by one switch on independent board

All as per item No 54 above but 2.5 Sqmm PVC insulated sheathed cable and 2.5 Sqmm cable for earth wire for one 5 Pin Socket out let 15Amp.

S&F Switch, Piano, flush type, Polycarbonate, 5 A, Single Pole, one way complete all as specified and directed.

S&F switch sucket combination, Polycarbonate,5 Amps, 2 in 1, 3 Pin/ 5 Pin, multipurpose, flush type complete all as specified and directed.

S&F switch sucket combination, Polycarbonate, 2 in 1, 3/5 Pin, 5/15 Amps, multipurpose, flush type complete all as specified and directed.

S&F Lamp Holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F LED retrofit lamp B-22 holder base with polycarbonate diffuser 9 Watt, 230 volt complete all as specified and directed.

S&F ceiling rose PVC polycarbonate, isolated body, 3 terminals AC, 230 volt complete all as specified and directed.

S&F LED Bulk head light fitting IP 55 with Engineering plastic housing & clear prismatic diffuser with lamp of 1x 10 watt LED, with three core flexible PVC insulated copper conductor (multistranded) cable of size 23/.0193 from ceiling rose to fitting complete all as specified and directed.

S&F Ultra Slim LED MS batten light fitting, 1 x 20 watt powder coated decorative end cap complete with retrofit poly carbonate glass tube 4' long including electric connection with three core flexible PVC insulated copper conductor multistranded cable of 1.0 sqmm from ceiling rose to batten complete all as specified and directed.

S&F Ceiling fan 1200mm sweep complete with all accessories such as rubber reel, split pins, check nuts, fan blades, PVC conopy, fan clamps, capacitor, PVC connector etc. and suitable electric connection with three core flexible PVC insulated copper conductor (multistranded) cable of 1.0 Sqmm from ceiling rose to fan complete all as specified and directed.

S&F of Exhaust fan 450 mm sweep, Iron body, AC, 230 volts with louvres including making suitable size hole in the wall for air flow and grouting of nuts, bolts and washers including electric connection with three core flexible PVC insulated copper conductor multistranded cable of 1.0 sqmm from ceiling rose complete all as specified and directed.

S&F Stepped type electronic fan regulator, flush mounting type, 180Watt, 230Volt complete all as specified and directed.

Supply and fix Security light fitting, LED type, 25 Watts, 6000 K, Pressure die cast housing with Prismatic Polycarbonate diffuser & individual LEDs as light source with integrated electronic driver complete with GI Pipe Mounting bracket of size 32mm dia and 1.20m long fixed to wall with and including nuts, bolts and GI clamps made out MS flat Iron of size 50x6mm as required including two coats of synthetic enamel over a coat of primer and making connection with three core 23/0.0076 rubber insulated copper cable from ceiling rose to connector of street light complete all as specified and directed.

Supply and lay bricks old size, well burnt, sub class 'B' bricks as in protection cover over under ground cable laid flat across the cable adjoining each other, laid dry complete all as specified and directed

M & L for river washed and screened sand for filling in trenches below and around the under ground cable including necessary punning for cushoining of cable complete all as specified and directed. Note : For measurement purpose, the punned down thickness of 18cm only shall be considered.

M&L for Bore holes under road or cutting the road /pavement /hard standing or any other situation by mechanical or other means for inserting 25 to 40mm bore GI pipe for crossing the cable and making good both the ends complete all as specified and directed.

S&F of galvanized iron pipe of 25 mm bore, Light grade with all fittings for cable protection for road crossing/ culvert/ path/ on wall/ floor/ pole or laid in floor complete all as specified and directed.

Supply, lay, jointing, testing and commisioning XLPE insulated screened PVC bedded, armoured, heavy duty electric cable with stranded aluminium conductor, 1100 Volts grade, cross sectional area 10 Sqmm 2 core complete all as specified and directed. Note :- Excavation earthwork, sand cushioning & brick protection shall be measured & paid seperately.

Supply and fix flush Sheet Metal enclosure, SPN, DB, 8 Way with double door, IP-42 Protection, detachable gland plate, flush mounting for MCB fitted with bus bar, earth bar and neutral links complete all as specified and directed.

S&F MCB, SPN 16 Amp to 63 Amps, 240 Volt complete all as specified and directed.

S&F MCB, Single Pole, 6 to 16 Amps, 240 V, 'B' curve, 10 KA complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6.3 mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metres below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts,check nuts, nuts and washers of GI or steel all as shown in electrical plate No 3 of SSR-I connected to earth test point by means of nut, bolts and washers made out of galvanised iron or steel all including earthing pit in PCC (1:3:6) type C1,RCC (1:2:4) type B1 precast cover slab with one handle made out of 8 mm dia round bar,20 mm dia (medium grade) protecation pipe and providing layer of charcoal or coke and salt in alternative layers,necessary excavation & earth work in any type of starta complete all as specified including testng on completion complete all as specified and directed.

Vasundhra Enterprises

M/S ABHISHEK ENTERPRISES