REPAIR TO ROOF, JOINERY, FLOORING, WIREMESH, WOOD WORK AND OTHER B/R ITEMS AT SECTOR V TO XI AND REPAIR AND REPLACEMENT OF ROAD FURNITURE AND MARKING OF PAINTING LINES TO OLD EXISTING ROAD SURFACE AT CHARDUAR AREAUNDER GE (NORTH) TEZPUR

Amount

Note 1: (Applicable for all parts/items) : The biidders/contractors are advised to read tender document, all drawings & all corrigendum/amendments and general condition of contracts before entry/quoting the rates. Note 2:- Attention to bidder is hereby invited to upload revised BOQ if published during their bid submission. Uploading of incorrect/ pre-revised BOQ shall be treated as non bonafide and rejected. Fixed credit has been given in technical documents which shall be taken into account during acceptance of bid/tender.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n exc 15 cm thickness ( below or above ground level).

Demolition of cement concrete (reinforced) of any description and in any position not other wise specifically provided for.

Dismantling of Asbestos cement (corrugated or semicorrugated etc) sheets in roof/ridge coverings

Dismantling plain or corrugated steel sheeting , any gauge, thickness including Nainital or similar pattern roof/ridge coverings.

Demolition of Brickwork or stone/boulder masonry, build in lime mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing

Demolition of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets and incl taking down carefully pointwiring for refixing.

Dismantling of timber scantlings 40 Sqcm and over in section in any position (unframed work)

All as per item no (8) but in fillets, rails, posts, rafters, purlines etc.under 40 Sqcm in section. (Unframed work)

Dismantling mild steel work of any description not otherwise provided for

Dismantling of boarding , any description , fixed in any position with nails.

Hacking out old broken glass (any thickness size,quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads complete all as specified and directed

Taking down shutters of any description n exc 1 Sqm each complete all as specified and directed

All as per item no (13) but exc 1 Sqm n exc 2 Sqm complete all as specified and directed

Taking down chowkhats with shutters of any description n exc 1 .5 Sqm each complete all as specified and directed .

Taking down chowkhats with shutters of any description exc 1 .5 Sqm but n exc 4 sqm each each complete all as specified and directed

Taking up or down 15mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and directed

All as per item No (17) but 20mm bore.

Dismantling water tanks of capacity exc 500 & nexc 1000 litres and removing to store.

Dismantling water tanks of capacity exc 250 & n exc 500 litres and removing to store.

Dismantling of floor hearth or wall tiling, including cement bedding but not backing and rubbish off the premises.

M&L for brickwork with sub class’B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:4.Complete all as specified and as directed.

M&L for brickwork with sub class’B’ bricks, straight or curved on plan exc 6m mean radius in half brick thick wall built in CM 1:4.Complete all as specified and as directed.

Taking down cement plaster of any description on brick or stone wall etc, including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed by Engr in Charge.

M&L for rendering 15 mm thick, CM 1:4 on fair faces of brick work or concrete surfaces by making surfaces even and smooth (mixed with water proofing compound which shall be measured and paid for separately under respective item) without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick, CM 1:6 on other than fair faces of brick work or concrete surfaces by making surfaces even and smooth without using extra cement complete all as spfd directed.

M&L GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding , joists, etc. In walls, ceilings, stanchions, beams, etc. Including all laps , cutting and waste.complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:4, on one side of lathing and making surfaces even and smooth without using extra cement. complete all as specified and directed.

M&L for rendering 15 mm thick, CM 1:4 on other side of lathing by making surfaces even and smooth (mixed with water proofing compound which shall be measured and paid for separately under respective item) without using extra cement complete all as specified and directed.

S&F for rolled mild steel in joist, channel, angle or tee / tubular sections , fixed independently with connected plates Fe 410-W (Gde- E-250) quality-A complete all as specified and directed

M&L second class wrought hard wood in scantlings (Timber fixed) complete all as specified and directed

M&L for 20mm thick second class hardwood planed at both sides boarding as in eaves boards complete all as specified and directed

M&L for 6 mm thick asbestos cement corrugated or semi-corrugated sheets in roofs, walls ,sunshed etc fixed with L-Type or J-Type or cranked hook bolts complete all as specified and directed

S&F for 0.63mm thickness of Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screw and washers, in roofs, walls etc with grade of zinc coating 275 fixed with L-type or J-type or cranked hook bolts in lieu of screws complete all as specified and directed

S&F for 0.63mm thickness Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed

M&L for pre painting galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding incl ridge hip etc fixed with tapping screws & L type or J type hooks etc complete all as specified and directed

M&L for pre painting galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding incl ridge hip etc fixed with tapping screws & L type or J type hooks etc complete all as specified and directed

M&L 4mm thick asbestos cement plain building boards, fixed to timber framework in ceiling with screws, and including refixing of old point wiring and fittings and replaceing old damaged fittings complete all as specified and directed

M & L including preparing of new surfaces and treated with three coats of white wash on new AC board ceiling surfaces complete all as specified and directed

S& F Anodised aluminium snap grid frame of size 605 x605 work for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof by means of ceilling cleats/ 2 mm dia wire made out of G.I. flat 40 x 3 mm size 60mm complete all as specifiedall as specified and as directed

S&F 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws®as specification complete all as specified and directed

M&L for 2nd class hard wood plain fillets ,square, rectangular or triangular in section ,clean sawn ,secured with nails or brads (sectional area exc13 sq.cm & n exc 25 sq.cm)as in studs of ceiling/sunshed complete all as specified and directed

M&L for 2nd class hard wood plain fillets ,square, rectangular or triangular in section ,clean sawn ,secured with nails or brads (sectional area exc 3 sq.cm & n exc 6 sq.cm)as in fillet complete all as specified and directed

All as per item no (45) but (sectional area exc 6 sq.cm & n exc 13 sq.cm) as in forking pieces in ceiling complete all as specified and directed

M&L for 75mm thick cement concrete type C-2,1:3:6(40mm graded aggregate) as in plinth protection ,footpath and making finished even and smooth without using extra cement complete all as specified and directed

M&L for 40 mm thick cement concrete type B-1,1:2:4(20mm graded aggregate) as in floor th and making finished even and smooth with using extra cement complete all as specified and directed

M&L for 38 mm width of strip glass dividing strips , 3 mm thcik and inserted in position complete all as specified and directed

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor/ wall finishes in CM 1:4 complete all as specified and directed

M&L for rendering 10 mm thick rough plastering on vertical fair faces of brickwork surfaces in CM1:4 complete all as specified and directed

M&L for non skid coloured tiles 7mm thick area of each tile exc 0.11 Sqm but n exc 0.18 sqm , in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed

Ditto but in skirting

M&L for Vitrified ceramic tiles 10mm polished area of each tiles n exc 0.36 Sqm in floors and as in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed

Ditto but in skirting

M &L for glazed coloured tiles in vertical surfaces. but 300mm x 200mm x 7mm thick set and jointed in cement slurry and pointed in colour to match complete all as specified and directed

S & F 500 litre capacity ,rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) in position all specified in SSR Part –I including dismantling old tank complete all as specified and directed

S & F 1000 litre capacity ,rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) in position all specified in SSR Part –I including dismantling old tank complete all as specified and directed

S & F in repair 20mm dia of bore, ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed

S&F for second class hardwood plain,solid,straight,chowkats and frames,wrought,framed rebated on the solid ,rounded or chamfered ,put together with glue pinned at joints complete all as specified and directed

S & F 35mm thick 2nd class hard wood plain, framed, panelled shutters (any number of panels),with panels of timber flat on both sides(feather edged),or of veneered particle board medium density, wood particle board with commercial face veneers, fitted to chowkats complete all as specified and directed

S & F 2nd class hard wood glazed and skeleton shutters 35mm thick open rebated and prepared to received glass, without (sash bars), edges of framing plain , chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-I, Section 1 Clause 8.20 (a) complete all as specified and directed

S&F 30mm thick glazed and skeleton shutters 2nd class soft wood , open rebated and prepared to receive glass, gauge etc divided into squares, with plain, cham-fered or rounded, mitred and rebated sash bars provided with stiles and rails as specified in SSR Part I ,section 8 clause8.20(b) complete all as specified and directed

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rein forced with M.S. square tube supplying and fixing in opening as per specification and drawing complete all as specified and directed

M&L for Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plaincolour PVC© channel PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock and bottom rail on either side as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded. Sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement supplying and fixing in the frame at site as per specification and drawing complete all as specified and directed

S&F solid PVC wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and directed

S&f 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on wall to make PVC frame complete all as specified and directed

S & F 100mm medium weight ,cold rolled mild steel butt hinges.

S & F 75mm medium weight ,cold rolled mild steel butt hinges.

S & F 200 mm long mild steel barrel tower bolts ,stove enamelled black, with bright bolt.

S & F 150 mm long mild steel barrel tower bolts ,stove enamelled black, with bright bolt.

S&F in repair 300mm long mild steel sliding door bolts ,plate type , stove enamelled black,with bright bolt not less than 12mm with and including a minimum of 6 bolts and nuts , four on bolt plate and two on staple plate complete all as specified and directed

S & F in 125mm size mild steel pressed handles, oval type, stove enamelled black .

S & F 100mm size mild steel pressed handles, oval type, stove enamelled black .

S&F Butt hinges, medium weight cold rolled mild steel and fixed as 100mm long.

S&F as Aluminium anodised barrel tower bolts of extruded section and fixed as 200mm long

S&F as Aluminium handles cast type anodised 150mm long and fixed as complete

S & F Galvanized wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staples complete all as specified and directed

M & L for 3.00mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.50.m in each panecomplete all as specified and directed

S & F in repair 15mm bore medium grade tubes, galvanized, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed

All as per item No (80) but 20mm bore.

S & F in repairs 15mm bore chromium plated bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F in repair 15mm chromium plated Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

S&F in repair 20mm gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

M & L including preparing surfaces of new wood and wood based materials, of any description , not otherwise described, over 10 cm width or girth, and treated with two coats of synthetic enamel paint over coat of pink primer complete all as specified and directed

M&L for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of redoxide complete all as specified

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of putty complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement based paint complete all as specified and directed.

M&L including complete removal of existing treatment, preparation of old Plastered surfaces of wall and applying two coats of oil bound distemper over a coat of chalk whiting complete all as specified and directed.

M&L including complete removal of existing treatment, preparation of old Plastered surfaces of wall and applying two coats of cement based paint complete all as specified and directed.

M&L for preparing old surfaces of ceilings and applying three coats of white wash.

M&L for M.S. TMT bars 8 to 10 mm dia bent to shape required including cranking bending and binding with M.S wire not less than o.9mm dia complete all as specified and directed.

Use and waste rough finished Form work to soffits of suspended slabs flat or batter such as roof slabs, floor slabs and similar work not exceeding 200 mm thick complete all as specified and directed

M&L for R.C.C 1:2:4 type B1 nominal mix (using 20mm graded agg) as Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs complete all as specified and directed.

S&F Brass Hat and coat hooks, solid body, 175mm to 250 mm complete all as specified and directed

S&F in repair PVC syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed

S&F in repair Vitreous China wash basin, white, flat back, size 450 x 300 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets and cutting for pinning in ends of brackets or erecting stand complete all as specified and directed

S&F in repair of PVC connections 15 mm size with PTMT nuts of length 450 mm long complete all as specified and directed

S&F in repair of PVC connections 15 mm size with PTMT nuts of length 600 mm long complete all as specified and directed

S&F in repair of 15 mm bore Pillar taps, cast copper alloy, fancy type, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed

S & F brass chromium plated toilet paper holder complete all as directed by EIC complete all as specified and directed

S & F in repairs vitreous China squatting pan ‘Orissa’ pattern size 580 x 440mm white , with integral foot rests including provision of lime concrete bedding ( excluding flushing cistern and flush pipe) complete all as specified and directed

S&F in repair chromium plated shower roses with or without swiwel joints any size including fixing to steel pipe or union complete all as specified and directed

S & F brass chromium plated tubular towel rail 20mm dia complete all as specified and directed

S & F 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed

S & F PVC (SWR) bends of radius 75mm bore.

S & F PVC (SWR) junction single,(Single T) equal or unequal of radius 75mm bore complete all as specified and directed

S & F PVC (SWR) vent cowl 75mm bore complete all as specified and directed

M&L integral waterproofing compound complete all as specified and directed

S&F in repair wash down water closet (pedestal pan) including connection to drain pipes and to flushing pipes antisy phonage pipe etc excluding flushing cistern incl flush pipe complete as as specified and directed

Supply and fixing in repair two way reflective cat eye studs not less than 100mm x 100mm x 18.5mm made of ABS plastic body of high compressive strength with electronically welded prismatic retro reflective lens on both sides for maximum retro reflection in wet & dry condition fixe with suitable bitumen adhesive on the road surface complete all as specified. (Model No DA 978 of Make : Dark Eye or equivalent in 3M/ACE/AUTOMAT as approved by GE

M&L for 2.5mm thick road marking strips (retro reflective) of specified shade/colour using hot thermoplastic material by fully/semi automatic thermoplastic material applicator machine filled with profile shoe, glass beads dispensers, propane tank heater and profile shoe heater, driven by experienced opertator on road surface including cost of material, labour, T&P cleaning the road surface of all dirt, seals, oil grease and foreign materials etc complete all as specified and directed.

S&F in repair Solar road studs size 125mm x 125mm x 25mm made up of highly compressive materials to sustain over 10 tonnes, 100% water proof design accrding to IP65 with minimum 3 super bright LED lens on each opposite sides (2sides only), with inbuilt solar panel of high effciency mono crystalline not less than 2.4V/0.3 watt with recharge battery not less than 1.2V/1500 MA and fixing the stem firmly intoroad surface as per manufacture instruction by hammering /embedding complete all as specified and directed by Engineer-in-Charge. (Model : Dhruv of Make: Dark eye or equivalent in 3M/AUTOMAT/ACE as approved)

S & F dual directional delineator 600 mm long made out of 16 gauge MS pipe of stove enameled and baked to 120 degree powdered coated head made out of ABS plastic rectangular mount with flat face provided with high intensity prismatic reflector of colour ( white/yellow/red) of size 100x125 mm with additional two reflector strip of 25 mm wide complete all as specified and as directed by Engineer-in-Charge. (Note :- Delineator shall be fixed in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate with size of block 300x300x350 mm deep, excavation and earth work shall be incuded in the unit rate of this item. Nothing extra shall be paid on this account (Make:- Greenlite ( Patent act 1970) Cat part No GPL -UBPH-11-56 or equivalent model of international wire products / TATA BP/ Darkeye model DA-74 or other make as approved by GE)

S&F in repair Solar powered delineator made of Polycarbonate and toughned aluminium alloy body with four super bright LED flashings, high quality reflective solar panel to absorb maximum sun obsorbtion, battery voltage 1.2V, Visibility minimum 120 Mtrs , working time 24-48 Hrs , Dimension of system not less than 145mm x 80mm x 80mm . Fixed on post size 1.0 mtr long made of 50 mm MS pipe painted with stove enamelled black paint including fixing the pole in PCC 1:3:6 type C1 (using 20mm graded stone aggregate) foundation size 20cmx20cmx40cm deep including necessary excavation and removal / disposal of spoils etc.,complete all as specified and as directed (Model SOLAR DELINEATOR of Make Dark Eye or equivalent in 3M, / Sinor Infrastructure / AUTOMAT / ACE as approved by GE)

Supply and fix convex mirror 1000mm made of PC material provided with suitable MS pipe post, duly Powder coated, meant for Road turning, intersections, curves, T junctions, Hospital, parking lots etc with clear & definite mirror image having 130 degree of viewing angle, unbreakable & stronger than glass, spring post (710mm x 80mm x 210mm) body of spring is made of special flexible material (polyurethane) without it can be quickly resorted to its original state without doing any damage to spring posts as well as vehicles in case of high speed collision by vehicles. Two bands of reflective tape are pasted on the spring post. Epoxy bond is used to fix the spring post with road surface the bond is so strong that post will not be deviated by strong impact after installation length of spring post 710mm, upper dia 80mm & bottom dia is 210mm complete all as specified & directed by Engineer-in-charge. Make : Trafitronics Indo Pvt Ltd Model No TRF-ON-001 or equivalent in Dark eye, Greenlite , TATA BP

M/S Bishwanath Mahato

M/S SONITPUR BUILDERS

M/S SEWAK SINGH

M/s Brahamaputra Wood Industries

M/S L N ENTERPRISE

Bidder Name

M/S SONITPUR BUILDERS