Special repair to Bldg No T-13 with toilets and bathrooms at 27/4 Camp and Provn of certain sanctioned works and Demolition of Bldg No. 31C, 32C, T-5 and T-40/B at Yol Cantt under AGE B/R-I of GE (KH) YOL

Amount

PART-I:- Excavation in trenches n exc 1.5 metre wide & n exc 1.5 metre in depth for foundation etc or for shafts, wells, cesspits manholes, pier holes etc n. exc 10 Sqm on plan n exc 1.5 metre in depth and getting out in any type of soil, complete all as specified and directed.

Plain cement concrete M-7.5, nominal mix, D-2, using 40mm graded mechanically crushed stone aggregate as in foundation filling and mass concrete, complete all as specified and directed.

Brick work with fly ash bricks, old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed.

Brick work with old size fly ash bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed.

Removing excavated material not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc.25cm thick each layer of soil, complete all as specified and directed.

Rendering cement plaster 15mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified and directed.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, mixed with WPC @3%, complete all as specified and directed. Note : Supply only Water proofing compound shall be measured and paid for seperately.

Supply only integral water proofing compound, complete all as specified and directed.

Two coats of oil bound distemper on newly plastered surfaces over 2mm thick wall care putty including preparation of surface, complete all as specified and as directed.

Two coats of cement base paint on newly plastered surface of wall including preparation of surface, complete all as specified and directed.

Glazed ceramic coloured tiles of size 350x250x/450x350x7 to 8mm thick as in vertical surfaces such as jointed in neat cement slurry and pointed with white or coloured cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in any type of soil, complete all as specified and directed.

Hard core of broken stone or boulders of gauge not exc. 63mm deposited, spread and levelled in layers not exc. 15cm thick, watered and rammed to a true surface, complete all as specified and directed.

75mm thick Plain cement concrete M-7.5 nominal mix, D-2, using 40mm graded mechanically crushed stone aggregate as in sub base/flooring, complete all as specified and directed.

Plain cement concrete M-15, nominal mix, type B-0, using 12.5mm graded mechanically crushed stone aggregate as in floors/levelling course, 25mm thick, surface finished even and fair, complete all as specified and directed.

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.06 Sqm but not exc. 0.11 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified and directed.

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), complete all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).

Plain cement concrete M-15, nominal mix, B-1 using 20mm graded mechanically crushed stone aggregate as in lintels upto 1.5 metre clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs, roof benching, haunching, water troughs and the like including watering, slightly rounded or chamfered angles and throating, complete all as specified and directed. Note :- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.

Reinforced cement concrete, M-15 (Nominal mix), type B-1, (with 20mm graded crushed stone aggregate as) in beams, cantilevers, bressummers, lintel, over 1.50m span, complete all as specified and directed. Note:- (i) Reinforcement if any shall be measured and paid separately.

Reinforced cement concrete, M-15 (Nominal mix), type B-1, (with 20mm graded crushed stone aggregate as) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed. Note:- (i) Reinforcement if any shall be measured and paid separately.

Formwork to soffits of suspended slabs such as roof slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), etc. For fair finished flat surfaces of concrete, complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for fair finished flat surfaces of concrete, complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including suports, overhangs, etc. also splays between floors and beams, etc. For fair finished flat surfaces of concrete, complete all as specified and directed.

Rendering cement plaster 5mm thick in cement mortar 1:3 (1 cement : 3 coarse sand) on fair faces of RCC concrete surfaces and including applying cement slurry in bottom of slab, chajjas, fin, facias etc and finished even and smooth without using extra cement, complete all as specified and directed.

Three coats of white wash on newly plastered or un plastered, previously undecorated wall surfaces including preparation of surfaces, complete all as specified and directed.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 180 of MES SSR 2020 Part-II.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5 mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1), complete all as specified and directed.

Butt hinges (ISI marked), medium weight, cold rolled, stainless steel 100mm long, complete all as specified and directed.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 100mm, fixed, complete all as specified and directed.

Extruded aluminium alloy handles (ISI marked), fabricated type, anodised, of size 150mm, fixed, complete all as specified and directed.

Mild steel galvanized iron water tubing 15mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor, complete all as specified and directed.

Factory made fully glazed PVC (frosted/ground/obscured) window/ventilator shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; completespecified and directed. Note:- Glass gauges inclusive of quoted rates.

Mild steel galvanized iron water tubing 20mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor, complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick walls, complete all as specified and directed.

Vitreous China wash down water closet (pedestal pattern), coloured including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, 15mm dia PVC connection 600mm with CP brass coupling nuts and PVC washers at both ends, fixed complete, including 32mm dia PVC long bend flush pipe 90cm long pipe and fixed, complete all as specified and directed.

Supply only Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

Wash basins, Vitreous China (Flat back type) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with CP coupling nuts at both ends, waste pipe of polythylene of low or high density or PVC of 32mm dia and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed, complete all as specified. Make:- Cera Cat part No 1008 or equivalent makes in Appx 'C'.

Supply and fixed PVC valveless, crystal white, syphonic action type flushing cistern 10 litres capacity, plunger type low level with inlet, ball valve, float and handle with brackets including 15mm dia PVC connection 600mm with CP brass coupling nuts and PVC washers at both ends, fixed complete, all as specified. Make:- Cera Cat part No 2602 or equivalent makes in Appx 'C'.

Flush pipe of polyethylene of low or high density or PVC 32mm dia, for low level cistern, including Joint between fluslhing pipe, complete all as specified and directed.

M & L for Brass CP mixer suitable for 15 mm dia pipe for mixing hot & cold water, fixed, complete all as specified and directed by Engr - in - Charge.

Bib taps, 15mm bore, cast copper alloy with crutch or butterfly handle, fancy type chromium plated screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

15mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule fixed, complete all as specified and directed.

Rotational moulded polyethylene water storage tank 1000 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position inncluding PVC float valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with water supply line, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors bore 110mm complete, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors bore 75mm complete, complete all as specified and directed.

PVC (SWR) bends any radius, 110mm, complete all as specified and directed.

PVC (SWR) bends any radius, 75mm bore, complete all as specified and directed.

PVC (SWR) floor trap, plain with CP grating including jointing with solvent cement, dia of outlet 75mm, complete all as specified and directed.

PVC (SWR) reducer 110mm bore, complete all as specified and directed.

PVC connection 15mm size with PTMT nuts at boths end 600mm long and fixed, complete all as specified and directed.

Soap dish, vitreous China white, approximate size 160x160x90mm, chromium plated, fixed to plugs with chromium plated, brass screws, fixed, complete all as specified and directed.

Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) and fixed, complete all as specified and directed.

Brass Chromium Plated, Tubular towel rail, 20mm dia, D type, 60cm long between flanges, with brackets, fixed with chromium plated brass screws, fixed, complete all as specified and directed.

PVC (SWR) 75mm vent cowl, complete all as specified and directed.

32mm dia waste coupling of PTMT (half or full threaded). (Minimum weight 32mm-45gms/40mm-60gms), complete all as specified and directed.

TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

TMT bars 5 to 10mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips as in stirrups, spacers and binders, complete all as specified and directed.

Plain cement concrete M-10 nominal mix, type C-2 using 40mm graded mechanically crushed stone aggregate as in surface channel and drains, complete all as specified and directed.

S&F for ‘P’ or ‘S’ trap of 110mm dia, complete all as specified and directed.

Bottle trap 32mm bore of PTMT having minimum water seal of 25mm. (Minimum weight 32mm-260gms/ 40mm-270 gms), complete all as specified and directed.

20mm bore Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions cutting, threading existing GI pipe and fixed, complete all as specified and directed.

4mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 Sqm in each pane, complete all as specified and directed.

Excavation in trenches not exc 1.50 metre wide and exc. 1.50 metre but n exc 3 metre in depth for foundation etc or for shafts, wells, cesspits manholes, pier holes etc n. exc 10 Sqm on plan n exc 1.50 metre in depth and getting out in any type of soil, complete all as specified and directed.

Reinforced concrete pipes, class NP2, laid and jointed complete with collars, bore of pipe 150mm, complete all as specified and directed.

Plain cement concrete M-10 type C-2 nominal mix using 40mm graded aggregate as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for internal dia of pipe 150mm, complete all as specified and directed.

Providing precast reinforced cement concrete M-15, type B-1 (using 20mm graded mechanically crushed stone aggregate) but in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set in cement mortar (1:6) (1 cement : 6 coarse sand), complete all as specified and directed. Note :- (i) Reinforcement if any shall be measured and paid separately.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped end etc., complete all as specified and directed.

50mm thick sand filling under floors or in foundations including watering and consolidations, complete all as specified and directed.

Machine pressed precast concrete interlocking paver block factory manufactured (ISI Marked), any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigment, complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out in any type of soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm and removing surplus soil to a distance n.exc 50m and making good the surface, complete all as specified and directed.

Plain cement concrete M-10, nominal mix, C-2, using 40mm graded mechanically crushed stone aggregate as in foundation filling and mass concrete, complete all as specified and directed.

Mild steel angle iron work in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed.

Mild steel 10mm dia of neck and length exc 5cm but n.exc 10cm screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire, complete all as specified and as directed by Engr-In-Charge.

Supply Only Chain link hot dipped galvanisd fencing, any size or type, complete all as specified and directed.

Applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

Chequered cement concrete tiles machine pressed of size 20cmx20cmx 25mm thick with grey cement and no pigment, set jointed & pointed in neat cement slurry in floors laid over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Surface excavation and cutting and dirooting complete of vegetation, shrubs, bushes etc and removing the same from site exc 1.5km and depositing the same as directed and making good the surface, complete all as specified and directed.

Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed.

Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails, straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins, etc., fixed in repair, complete all as specified and directed. (each line wire to be measured)

Mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed ballusters walk ways; railings; framework of water tanks and similar work like side hung gate including pintel hinges conforming to Fe.290. Gde-E-165, complete all as specified and directed.

Rolled sections as in Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161- 1979 grade St.-240s, steel work, complete all as specified and directed.

Rolled sections as in main and cross beams, hip and jack rafters; purlins angle for shed where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc. conforming to grade Fe.410-W.Gde-E-250 quality A, steel work, complete all as specified and directed.

Mild Steel framed work as Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete, conforming to Fe 410 Gde E-250 quality B, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge, hips, valley gutters, drip and straight flashing (length and girth as fixed), fixed with self tapping screws, complete all as specified and directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.50 Sqm but not exc. 4 Sqm each and removing from site, complete all as specified and directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.50 Sqm each and removing from site, complete all as specified and directed.

Taking down shutters of any description exc. 1 Sqm not exc. 2 Sqm each and removing from site, complete all as specified and directed.

Pressed steel frames of size 105x60mm for door with one or more rebates including necessary fixing lugs, hinges, lock strike plate, 25x3mm flat iron 230mm long hold fast, 75mm long MS butt hinges etc, including back filling with PCC M-10 (nominal mix) type C-0 using 12.50mm graded crushed stone aggregate, complete all as specified and directed.

Factory made 35mm thick second class hard wood (Sal) rail and style Plain framed, panelled shutter without interlocking rail and with one panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet and edges shall be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 176- of MES SSR 2020 Part-II, complete all as specified and directed.

M&L WPC (Wood Polymer Composit) Double Prelam Door Frame (Chowkhat) of Size 120mm x 50mm with a wall thickness of 5mm(+/- 0.25), made out of extruded 5mm(=0.25) mm thick PVC Sheet of Density 600kg/cbm manufactured y an ISO 9001-2015 certified company and by joining 3 Nos heat moulded PVC Sections. The high section of size 35 x35 mm shall be maid from plain colour PVC sheet of 5mm (=/- 0.25 mm) thickness. The inside section will be covered with 5mm thick PVC sheet 'C' shape covering section of size 120mm x 50mm. At centretop position 5mm(+0.25mm) thick 50 x50 x50 mm pattam section should be pasted with solvent cemen adhesive to make double pattam of frame. The frame shall be mitre cut at two corners & joined with 4 nos of 150mm long 'L' brackets of 19 x 19 mm MS square, Tube or fusion heat welding process. The two vertical door frames are to be reinforced with 25 x 25 mm MS square Tube of 19 gauge throughout the frame. The Door Frame shall be fixed to the wall using 8/100mm fischer screws. A minimum of 4 nos of screws to be provided for each vertical member & minimum 2 Nos. for horizontal member etc. complete as per manufacture's specification & direction of engineer-in charge.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of solid core single Leaf Flush Door of 25mm thickness, lipped with 15mm (5mm x 3) thick x 30 mm width on one stiles and top rails & 10mm (5mm x 2) thick x 30 mm width on the other stiles & bottom rails. The inner panel Laminated with 2mm thick termite proof, water proof & fire resistant moulded PVC sheet with 2,4,6 raised panel design in different plain &/or prelam colors on one side after routing the mouldd design on flush door & 2mm plain and/or prelam PVC sheet on other side using rubber based adhesive on flush door & solvent cement adhesive on the lipping etc. complete as per direction of Engineer-in-charge, manufacture's specification and drawing.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads, fixed, complete all as specified and directed.

Sheet glass 3mm thick ordinary quality and glazing with oil putty/wooden beads in squares, not exc. 0.50 sqm in each pane, complete all as specified and directed.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 150mm, fixed, complete all as specified and directed.

Extruded aluminium alloy handles (ISI marked), fabricated type, anodised, of size 100mm, fixed, complete all as specified and directed.

Butt hinges (ISI marked), medium weight, cold rolled, stainless steel 75mm long, complete all as specified and directed.

100mm size steel locking bolts with mild steel electrogalvanised plate and bright bolt not less than 10mm dia, complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 250mm with lipping frame to match, complete all as specified and directed.

Applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surfaces of any description, exc. 10cm width or girth including preparation of surfaces, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish of the premisses, complete including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Taking down cement plaster on brick or stone walls, ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete including removal of debris to a distance exc 1.50 km but n.exc 2 km, complete all as specified and directed.

Vitrified ceramic tiles light shade, 10mm thick (Square/ rectangular) area of each tile not exc. 0.36 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed.

Vitrified ceramic tiles light shade, 10mm thick (Square/ rectangular) area of each tile not exc. 0.36 Sqm, in vertical surfaces such as skirting and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick rendering in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified and directed.

Rendering cement plaster 15mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on other than fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified and directed.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over 2mm thick wall with plaster of paries putty, complete all as specified and directed.

Preparation of old plastered or unplastered surfaces of walls including complete removal of existing treatment and applying two coats of oil bound distemper over 2mm thick wall with plaster of paries putty including cleaning the floor/joinery surfaces, glass pans, complete all as specified and as directed.

Preparation of new plastered surfaces of wall and applying finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), complete all as specified and as directed.

Preparation of old plastered or unplastered surfaces of wall including complete removal of existing surfaces and applying finishing walls with Acrylic Smooth exterior paint of required shade (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), complete all as specified and as directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets in ceiling, complete all as specified and directed.

S & F for false ceiling of 600mmx 600mmx 4mm thick Non asbestos fibre cement building boards (designed prepainted) fixed or laid/ inserted to timber/GI/Aluminium framework with screws (E-boards) manufactured from homogeneous mixture of cement, quartz and cellulose and cured with high pressure steam using auto claving process conforming IS-14862, of size 600mmx 600mmx 4mm thick fixed over and including anodised powder coated (minimum thickness of powder coating 50 micron) GI snap grid frame work of T section (main and cross members) of size 25mmx 25mmx 1.5mm thick in square pattern of grid size 600mmx600mm. The aluminium frame work will supported on side wall with the used of aluminium L section of size 25mm x25mmx 1.5mm thick angles etc. snap grid shall be supported with hangers of 4mm dia galvanised iron wire adjusting level fixed to roof roof slabs/trusses etc. by means of ceiling cleats made out of galvanised iron flat of size 40x3mm of size 60mm long and expansion hold fasteners 12.5mm dia 40mm long, complete all as specified and directed. Make:- Everest or equivalent as approved by GE.

Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins arches, pillars, complete all as specified and directed.

Walling random rubble masonry with best quality locally available stone, uncoursed, well bonded, bedded, solidly hearted and built in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified and directed.

Vitreous China wash down water closet (pedestal pattern), coloured including traps, connection to drain or outgoing pipe, flushing pipe of polyethylene of low or high density, anti-syphonage pipe complete including fittings, PVC coloured seat cover black closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device and chromium plated jet spray including 15mm dia PVC connection 600mm with CP brass coupling nuts and PVC washers at both ends, fixed complete, including PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve, float and handle with brackets with including 32mm dia PVC long bend flush pipe 90cm long pipe, fixed in repair, complete all as specified and directed.

Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with PVC ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-1 using 20mm graded crushed stone aggregate complete all as specified, including PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve, float and handle with brackets with PVC 32mm dia flushing pipe, anti-syphonage pipe, fixed in repair, complete all as specified and directed.

Wash basins, Vitreous China (Flat back type) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450mm long PVC connections 15mm size with CP coupling nuts at both ends, waste pipe of polythylene of low or high density or PVC of 32mm dia including Pillar taps fancy type, 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed in repair, complete all as specified and directed.

Taking up or down 15mm bore, steel tubing and connections, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking up or down 20mm bore, steel tubing and connections, including cleaning for refixing or removal from site, complete all as specified and directed.

All as per Serial Item No 32 above but except pipe. (Note:- Serviceable pipe retrieved from Serial Item No 124 shall be used).

All as per Serial Item No 34 above but except pipe. (Note:- Serviceable pipe retrieved from Serial Item No 125 shall be used).

Bib taps, 15mm bore, cast copper alloy with crutch or butterfly handle, fancy type chromium plated screwed for iron pipe or for brass ferrule and fixed in repair, complete all as specified and directed.

Angular Stop Cock with Wall Flange, cast copper alloy, fancy type chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repair, complete all as specified and directed.

Harrison 25mm bore Curtain rails, mild steel, chromium plated with fixing brackets, stops and roller etc. fixed in repair, complete all as specified and directed.

Dismantling existing tanks and removing to store water tanks of capacity 500 to 1000 ltr, complete all as specified and directed.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position including brass ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line, complete all as specified and directed.

20mm bore Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions cutting, threading existing GI pipe line and providing 01 No 20mm GI union and fixed in repair, complete all as specified and directed. Note:- To be fixed in existing inlet of services tanks at 1.80m high from GL.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with adjustable clamps of bore 110mm, including taking out old pipe, complete all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with adjustable clamps of bore 75mm, including taking out old pipe, complete all as specified and directed.

PVC (SWR) bends any radius, 110mm bore with ovel access door, fixed in repair, complete all as specified and directed.

PVC (SWR) bends any radius, 75mm bore with ovel access door, fixed in repair, complete all as specified and directed.

PVC (SWR) floor trap, plain with CP grating including jointing with solvent cement, dia of outlet 75mm, fixed in repair, complete all as specified and directed.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm, fixed in repair, complete all as specified and directed.

M & L for Brass CP mixer suitable for 15 mm dia pipe for mixing hot & cold water, fixed in repair, complete all as specified and directed by Engr - in - Charge.

Dismantling plain or corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof covering, complete all as specified and directed.

Dismantling timber scantlings 40 sqcm and over in section, in any position, framed work, complete all as specified and directed.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe.290 Gde E-165, steel work, complete all as specified and directed.

2nd class soft wood (Kail) as in scantling clean sawn timber fixed in framed, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.63mm thick of any colour having tensile strength of 550 Mpa as in ridge, hips, valley gutters, drip and straight flashing (length and girth as fixed), fixed with self tapping screws, complete all as specified and directed.

Taking down of aluminium door shutter with frame including with all fittings, repairing and refixing the aluminium door shutter with frame in serviceable condition in same opening, complete all as specified and directed.

Powder coated anodized aluminium door chowkhat with shutter of approved design complete with all fixing arrangements including providing and fixing door handles, tower bolts, hydraullic door closer and mortice lock, hinges, door stopper including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- (a) Shutter vertical member 85.00 x 44.45 x 1.80mm weighing 1.302 Kg/RM. (b) Shutter top member 83.5 x 44.45 x 1.70 mm weighing 1.243 Kg/RM. (c) Shutter bottom member 114.30 x 44.45 x 1.29mm weighing 1.139 Kg/RM. (d) Shutter lock rail 83.5x44.45x1.70mm weighing 1.243 Kg/RM. (e) Anodised aluminium handle, fancy type 350mm longh, aluminium door closer and aluminium tower bolt of size 150mm. (f) 5.50mm thick tinted sheet glass fixed with alumnium beading, silicon lining and gaskets. (g) Aluminium anodised frame of door of section 101.6 x 44.45 x 1.75mm weighing 1.367 Kg/M, with flat iron hold fasts and necessary concrete in PCC M-15, type B-1 using 12.5mm graded stone aggregate to fix hold fasts all as directed. Note:- (i) Shutter shall be fixed with heavy floor spring ISI marked and pivot, brass lock with duplicate keys.

Powder coated anodized aluminium window (double shutter glazed and gauged) with chowkhat of approved design complete with all fixing arrangements including providing and fixing window handles, tower bolts and provision for fixing lock including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- (a) Shutter vertical member 47.62 x 45.45 x 1.74mm weighing 0.881Kg/RM. (b) Shutter top member 47.62 x 44.45 x 1.1.14 mm weighing 0.607 Kg/RM. (c) Shutter bottom member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (d) Natural colour 15 micr anodised aluminium anodised frame of chowkhat of section 85.00x44.45x1.80mm weighing 1.302 Kg/RM, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed. (e) 5.50mm thick tinted sheet glass fixed with alumnium beading, silicon lining and gaskets. (f) The size of Anodised aluminium round handle, fancy type shall be 100mm dia (02 Nos) and aluminium anodised aluminium tower bolt of size 100mm (02 Nos). (g) Wiremesh of standard size for approved shutter of sections mentioned above. Note:- All fixtures and fastenings required are included in this rate.

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin- charge.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement, all complete as per requirement and direction of Engineerin- charge.

Vitreous China Urinal, Half stall (back or corner wall type) including PVC waste pipe, including providing and fixing plugs, beding urinal against wall in cement mortar 1:2 securing urinal plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe including urinal spreader of PTMT any colour and fixed in repair, complete all as specified and directed.

Vitreous china urinal partition white of size 310x700 mm slabs terminating about 40cm above floor line, fixed in repair, complete all as specified and as directed by Engr-In-Charge.

Providing and fixing in position wall paneling at all heights with PVC wall panel/sheets (5-9mm thickness) of approved texture, design and patterns, using suitable formwork comprising of a frame made in the ceiling offsets from especially fabricated galvanized mild steel sheet and PVC wall panel/sheets of noncombustible are to be screw fixed with self-tapping pan head nickel coated mild steel screws as per direction of Engineer-in-Charge. Note: All fittings including PVC Strips like L,U etc fixed at corner edges, adhesives or any other are included in this item.

Rough excavation not exceeding 1.5 m deep and getting out in any type of soil, complete all as specified and directed.

75mm thick Plain cement concrete M-10 nominal mix, C-2, using 40mm graded mechanically crushed stone aggregate as in sub base flooring, finished even and smooth without using extra cement, complete all as specified and directed.

Two coats of cement base paint over a coat of primer, on newly plastered surface of wall including preparation of surface, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

Dismantling existing tanks and removing to store water tanks of capacity exc. 250 but n.exc 500 ltr, complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground, posts embedded in concrete, brick masonry etc. complete all as specified and directed.

Dismantling timber scantlings unframed work in fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section, complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings, complete all as specified and directed.

Reinforced cement concrete (nominal mix) M-15 type B-1 (using 20mm graded crushed stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed. Note:- Reinforcement and form work shall be measured and paid separately.

Reinforced cement concrete Nominal mix) M-15 type B-1 (using 20mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts, complete all as specified and directed.

Reinforced cement concrete Nominal mix) M-15 type B-1 (using 20mm graded crushed stone aggregate) as in arch beam over RCC column well bonded, complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, for fair finished flat surfaces of concrete, complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, for roughly finished square, rectangular or polygonal surfaces of concrete, complete all as specified and directed.

Formwork to sides and soffits of arches beams for fair finished surface, complete all as specified and directed.

Granite (of any type) 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the shade of granite stone including grinding and polishing complete as in kitchen platform, window cill /steps laid over and including 15mm thick screed bed in cement mortar (1:4), complete all as specified and directed.

M&L for decorate stone type pitching/tile/slate tiles best quality locally available fixed on wall with neat cement slurry/paste including rendering 15mm thick cement mortar 1:4 on stone masonary/brick masonary size and pattern to be laid as ordered by Engr-in-Charge.

Providing, fabricating and installing in position 4mm thickness aluminium composite cladding of "PIONEER, ALUTECH, ALSTRONG, ALUDECOR" are protected with self adhesive protection film by erecting over the wall using aluminium frames @ desired levels made with 50x25x1.20mm extruded channel sections conforming to IS-7333 mechanical properties. The frame shall be fixed on external wall surface with necessary brackets, bolt nut arrangements with screws aluminium L cleats, backer rod, wacker/dowcorning silicon sealant etc. @ all levels and heights and silicon sealant is filled in complete as per specification and directed by Engr-In-Charge.

Taking down point wiring with aluminium/ copper conductor for light point, fan & socket point/ power point etc. complete including switches, sockets, holders, (batten or pendent type), ceiling rose, switch board, bell/buzzer, bell push, and making good to the disturbed surfaces of wall/ floor etc. to match with existing surfaces including white wash/ colour wash/ distempering to match with existing wall/ floor/ ceiling finishes, complete all as specified and directed.

Taking down sheet metal enclosure DB, MCB, main switch etc and making good distrubed surfaces to match with existing surfaces, complete all as specified and directed.

Point wiring with 1.5 Sqmm copper conductor FRLS (Multi strand) PVC insulated ISI Marked unsheathed cable in and including PVC casing and capping conduit, ISI marked of suitable size with all fittings/ accessories and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FLRS as phase, neutral and earth wire connected to common earth dolly and including concealed MS pressed steel cadmium plated terminal boxes suitable for modular accessories made from 1.60 mm thick sheet for mounting of switches, sockets, fan regulators, light fittings etc. and 3mm thick laminated hylam sheet top cover (ISI marked) for one light point or one fan/exhaust fan point or one bell point, independent, controlled by one way switch/ push button, complete all as specified and directed. Note:-i) Wiring colour code i.e Red/Yellow/Blue for phase, Black for neutral and Green for earth shall be maintained. (ii) Rate of cutting chases if required shall be paid and measured seperately.

All as per serial item No '173' above, but for one 3 pin 5 Amps socket outlet on the same board with 2.5 sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 2.5 sqmm stranded copper conductor cable as continous earth wire, complete all as specified and directed.

All as per serial item No '173' above, but for one 3 pin 5 Amps socket outlet on the independent board with 2.5 sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 2.5 sqmm stranded copper conductor cable as continous earth wire, complete all as specified and directed.

All as per serial item No '173' above, but for 3 pin 15 amps socket out let on independent with 2.5 Sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, complete all as specified and directed.

Cutting chases in brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and directed.

Supply and fix modular bell switch one way 6 Amps, 1 module, 230V, Fixed complete all as specified.

Supply and fix modular switch piano flush type one way 6 Amps, 1 module, 230V, Fixed complete all as specified.

Supply and fix modular switch piano flush type one way 16 Amps, 1 module, 230V, Fixed complete all as specified.

S&F Modular socket 6 Amp 3 Pin, two module 230 Volts.

S&F Modular socket 6/16 Amp 5 Pin, two module 230 Volts.

S&F Modular fan regulator step type 100 Watt one module 230 volts.

Supply and fix modular bell push with indicator 6 Amps, 1 module Fixed, complete all as specified.

Ceiling rose, three phase, PVC/Polycarbonate, insulated body and fixed in repair, complete all as specified and directed.

Supply and fix modular cover plate with frame, 3 module, complete all as specified and directed by Engr-in- Charge

Supply and fix modular cover plate with frame, 8 module, complete all as specified and directed by Engr-in- Charge

Supply and fix modular metal flush box 3 module Fixed in repair, complete all as specified and directed.

Supply and fix modular metal flush box 8 module Fixed in repair, complete all as specified and directed.

Sheet metal enclosures factory made for DBs when MCBs to be used, single pole and neutral (double Door), 8 way, 240 volts with 200 Amp rated bus bar, complete all as specified and directed.

MCB SP 6 to 32 Amp, 240 Volts, 10 KA, C series including taking out old, complete all as specified and directed. Note:- The connection to the MCBs shall be done through thimble/lugs do not direct wire shall be connected to MCBs.

MCB SPN 40 Amp, 240 Volts, 10 KA C series including taking out old, complete all as specified and directed. Note:- The connection to the MCBs shall be done through thimble/lugs do not direct wire shall be connected to MCBs.

M & L for sub main wiring with two single core PVC insulated unsheathed, 1100 Volts grade, (FRLS) copper cable 6 sqmm stranded conductor and drawing through and including rigid PVC non metalic surface conduit medium duty (ISI Marked) with conduit accessories such as junction boxes, bends, tees etc. including continuous earth wire PVC insulated unsheathed 1100 volts grade, cable 6 sqmm copper conductor and connected to common earth dolly, complete as specified and directed, including taking down old submain wiring. Note :-(i) One run of PVC conduit, two runs of cable (Phase + Neutral) and one run of earth wire shall be measured and paid as one unit.

LED Decorative ultra slim square profile LED lighting integral type fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack, 16 watt LED, 230V, and making connection with 2 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light, including taking down old light, complete all as specified and directed.

LED Decorative ultra slim square profile LED lighting integral type fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack, 20 watt LED, 230V, and making connection with 2 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light, including taking down old light, complete all as specified and directed.

Supply and fixing of 35 Watt New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens enbedded PC cover having top opening seperate toughtned glass/verminproof driver compartment, SPDs with IP66 protection and impact resistance of IK07, connecting with PVC insulated three core flexible copper conductor of suitable size from ceiling rose to fitting including bracket of size 32mm dia lenght 1.2m along with clamps, including taking down old light, complete all as specified and as directed.

Supply and fixing in repair LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as required at site and directed by Engr-in-Charge.

Taking down ceiling fan of any sweep, any size/make from existing position of any height by disconnecting electrical connections and transporting to workshop. Inspection of ceiling fan in presence of Engr-in-charge/JE (or rep of department) after dismentling spares parts. Transporting ceiling fan back from work shop to site including hanging/ fixing and connecting up and testing etc complete all as required at site and directed by Engr - in - Charge.

M&L for complete repair and maintenance of unserviceable ceiling fan of 1200mm/1400mm sweep at work shop, incl dismantling complete the ceiling fan parts i.e. blades, fan rod, canopy, connection, inspecting serviceability of all the parts, re fixing of serviceable parts after cleaning and replacement of unserviceable parts with company's genuine parts i.e. capacitor, bearing, bushes, shaft, bracket, rubber bush, connecting wire, PVC connector, aluminium clamp for rod, bracket, bush rod, blade and greasing/oiling etc assembling, cleaning and testing of ceiling fan as directed.

Removing of old burnt winding wiring any type, cleaning stator complete for burnt wiring, carbon residue and rewinding of stator winding of any type/any make fan/ any stator design ceiling fan of 1200mm sweep with superior quality super enameled winding copper wire of existing specification, gauge and weight with superior quality insulation for satisfactory functioning fan in presence of JE incharge complete all as directed by Engr-in-Charge.

Replacement of earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of plate not less than 1.5m below ground level, connecting to galvanised iron wire 4mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in plain cement concrete M-20 type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of rainforced cement concrete M-20 reinforced with XPM (weight not less than 4 kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75m long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion. NOTE :- Item of earthing includes the cost of 7.5m long galvanised iron earth wire 4mm size and protection pipe of 15mm bore galvanised iron light grade and earth work.

Supply and fix modular metal flush box 3 module, complete all as specified and directed.

Supply and fix modular metal flush box 8 module, complete all as specified and directed.

Ceiling rose, three phase, PVC/Polycarbonate, insulated body and fixed, complete all as specified and directed.

Single pole and neutral enclosure with a two pin and earth plug top and socket complete with one double pole MCB 20 Amps, complete all as specified and directed.

MCB SP 6 to 32 Amp, 240 Volts, 10 KA, C series, complete all as specified and directed. Note:- The connection to the MCBs shall be done through thimble/lugs do not direct wire shall be connected to MCBs.

MCB SPN 32 Amp, 240 Volts, 10 KA C series, complete all as specified and directed. Note:- The connection to the MCBs shall be done through thimble/lugs do not direct wire shall be connected to MCBs.

M & L for sub main wiring with two single core PVC insulated unsheathed, 1100 Volts grade, (FRLS) copper cable 6 sqmm stranded conductor and drawing through and including rigid PVC non metalic surface conduit medium duty (ISI Marked) with conduit accessories such as junction boxes, bends, tees etc. including continuous earth wire PVC insulated unsheathed 1100 volts grade, cable 6 sqmm copper conductor and connected to common earth dolly, complete as specified and directed. Note:- (i) One run of PVC conduit, two runs of cable (Phase + Neutral) and one run of earth wire shall be measured and paid as one unit.

LED Decorative ultra slim square profile LED lighting integral type fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack, 20 watt LED, 230V, and making connection with 2 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light, complete all as specified and directed.

Supply and fixing of 35 Watt New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens enbedded PC cover having top opening seperate toughtned glass/verminproof driver compartment, SPDs with IP66 protection and impact resistance of IK07, connecting with PVC insulated three core flexible copper conductor of suitable size from ceiling rose to fitting including bracket of size 32mm dia lenght 1.2m along with clamps, complete all as specified and as directed.

Supply and fixing of Exhaust fan (domestic purpose) of sweep 300mm, single phase, with louver shutter and connecting with electrical system, including provision of cable copper flexible, PVC three core 23/0.0076 from ceiling rose to fan and grouting of holding down bolts, fixed on wall with angle iron frame of size 35 mm x 35 mm x 3 mm, complete all as specified and directed by Engr - in - Charge.

Supply and installing of the electric water storage heater of ABS body type of 25 litre capacity with rated power 2 KW, 5 star rated, vertical type, thermally insulated Mild steel tank with glass line coating inside the tank alongwith glass lined incoloy heating element with anti corrosive magnesium anode, NRV, thermostate, indicators and temperature adjustable knob including steel braided flexible connection for pipe of size 15mm dia bore GI hexagonal adopters/Nuts on both side of inlet (cold water supply) and outlet (hot water supply) and including provision of wall mounting arrangement and mounting on wall with suitable size of anchor bolts with complete connection of water including testing after installation, complete all as specified and as directed by Engr-In-Charge.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of plate not less than 1.5m below ground level, connecting to galvanised iron wire 4mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in plain cement concrete M-20 type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of rainforced cement concrete M-20 reinforced with XPM (weight not less than 4 kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75m long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion. NOTE :- Item of earthing includes the cost of 7.5m long galvanised iron earth wire 4mm size and protection pipe of 15mm bore galvanised iron light grade and earth work.

S&F of decorative post top lantern for 360 degree indirect light, IP 65 protection 230 volts, 50W complete and connecting the same to electrical source with using copper conductor 23/0.0076 round PVC insulated and sheathed three core cable, complete all as specified and directed by Engr-in-Charge.

Supply and fix LED focus light 20W, 220V AC surface mounted type with high efficiency PMMA diffuser soft glare free light complete with driver, holders and LED lamp including connecting up with driver three core flexible copper conductor cable of suitable size, complete all as specified and directed by Engr-in-Charge. Make:- Philips, Wipro, Crompton

Sheet metal enclosures factory made for DBs when MCBs to be used, single pole and neutral (double Door), 4 way, 240 volts with 200 Amp rated bus ba, complete all as specified and directed.

M&L for 50mm dia GI pipe light grade as in trenches, across road or pole, including elbow/union and cutting of hard surface as required, complete all as specified and directed.

1100 volts grade heavy duty cable PVC insulated aluminium solid conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular stranded conductor size of 10 sqmm x 2 core, complete all as specified and directed.

Eshaan Construction Co. (BID ID -3099327)

KISHAN CONTRACTOR (BID ID -3098416)