SPECIAL REPAIR TO OTM ACCN BLDG NO. P-149 (OR LINE) OF 14 REGT AND PROVN OF 17 X FIRE PTS (PLINTH WITH COVER) AT 314 FD HOSP, LADIES TOILET IN SIGNAL CENTRE COMPLEX, IRON STAIRCASE IN ADM BLOCK OF 614 EME BN, RCC PILLARS FOR DEMARCATION OF ALIGNMENT

Amount

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish off the premises from MoD all as specified and directed.

M&L for joint free Non- skid coloured ceramic tiles of any design and pattern, 300X300X7 to 8 mm thick, in floor etc incl 15mm thick screed bed in CM 1:4, Set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles complete all as specified and directed.

M&L for joint free coloured glazed ceramic tiles of any design and pattern, 300x450x 7 to 8 mm thick, as in dado etc incl 10 mm thick rendering in CM 1:3, Set and jointed in neat cement slurry and pointed in white of coloured cement to match the shade of the tiles complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc to receive tiles complete all as specified and directed

M&L for Non-skid joint free Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exc.0.38sqm in floor etc of any design and pattern, incl 15 mm thick screed bed in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles complete all as specified and directed

All as per item No 5 above but as in skirting/dado over 10mm thick cement plaster in CM 1:3. complete all as specified and directed.

M&L for Non-skid joint free Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exc.0.18 sqm in floor etc of any design and pattern, incl 15 mm thick screed bed in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles complete all as specified and directed

All as per item No. 7 above but as in skirting/dado over 10mm thick cement plaster in CM 1:3. complete all as specified and directed.

Demolition of cement concrete (unreinforced) above ground floors and paving exc. 15cm thickness (below or above ground level).

M & L 10mm thick rendering in CM ( 1 : 3 ) mixed with water proofing compound on fair faces of brick walls or conc surfaces and finished even & fair complete all as specified.(Note : water proofing compound paid separately)

Supply only liquid water proofing compound complete all as specified and directed

M& L for two coats of elastomeric compound ie super latex of Dr Fixit or equavalent on concrete surfaces after cleaning of sunken surface (vertical and horizontal) by removing all the loose mortar, laitance, dirt, dust etc by chiesel hammer/wire brush anc air blower machine complete all as specified and directed

M & L for plain cement concrete Nominal mix (1:5:10) type E2(using 40 mm graded brick aggregate) as in sunken floor complete all as specified and directed

M&L 25mm thick PCC (1:2:4) type B-1 (using 12.50mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

M&L 75mm thick PCC (1:2:4) type B2 (Using 40mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L cement concrete 1:3:6 type C-2 (using 40mm graded aggregate) 75 mm thick as in sub bases of floor complete all as specified and directed by Engineer in Charge .

M&L cement concrete 1:3:6 type C-1 (using 40mm graded aggregate) 75 mm thick as in plinth protection/hard standing surface finished even and smooth without using extra cement including providing 12mm thick groves at an interval of 3.0 mtr and filling the same with bitumastic compound grade "B" complete all as specified and directed by Engineer in Charge .

M & L Cement concrete type B2, 1:2:4 (40MM graded aggregate for surface channels and drains complete all as specified.

Demolition of brick work or stone masonry/stone slabs built in cement mortar including all quoins, arches, jambs etc complete all as specified and directed.

M&L Brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified.

Taking down cement plaster, from brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

M&L Rendering 15 mm thick on fair faces of brick work or concrete walls internal surfaces in CM 1:6 finished to even & fair without using extra cement.Complete all as specified and directed by Engineer in Charge .

M&L for rendering 15 mm thick in CM 1:4 on other than fair faces of brick or concrete surfaces finishing even and smooth without using extra cement complete all as specified and as directed .

M&L rendering 5 mm thick in CM 1:3 in ceiling / Chhajja's finished even and smooth (without using extra cement) Complete all as specified and directed

M&L for preparation of newly plastered surface of internal wall by application of 1mm wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying two coats of acrylic distemper over a coat of primer using roller all as specified and prescribed by manufacture of paint and as directed at site by Engineer-in-Charge.

M&L for preparation of newly plastered surface of external wall all as prescribed by manufacture of paint and applying two coats of exterior anti fungal acrylic emulsion paint (walmista of Berger paint or equitant in Asian paint, Nerolac etc having three years of performance warranty) over a coat of exterior water based primer of same make all as specified and prescribed by manufacture of paint and as directed at site by Engineer-in-Charge.

M&L for white washing three coats on ceiling incl preparation of newly plastered surfaces. complete all as specified and directed by Engr In Charge.

Taking up or down steel tubing and connection of 15mm dia, incl cleaning for refixing or removal to store complete all as specified and directed

Taking up or down steel tubing and connection of 20mm dia, incl cleaning for refixing or removal to store complete all as specified and directed

S & F 15mm dia GI tube medium grade galvanised with all fittings fixed complete to walls and ceilings or laid in floors complete all as specified and directed

S & F 20mm dia GI tube medium grade galvanised with all fittings fixed complete to walls and ceilings or laid in floors complete all as specified and directed

S & F in repair 20mm dia gun metal gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed

S&F in repairs PVC water storage tank cylindrical,triple layer vertical with closed top with threaded cover hoisted and fixed in position tank capacity 1000 Ltr with and including ball valve high pressure of PTMT with epoxy coated Aluminum rod and high density plastic ball screwed for 20mm bore of iron pipe and making connection for inlet and outlet and 20mm tank nipple (min weight 45gm) suitable for HDPE water tank including dismantle of old water tank and removing from site complete all as specified and directed.

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes, ( ISI Marked), single socketed in any length with rubber ring joints laid in trenches or in floors/walls complete all as specified and directed.

S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes ( ISI Marked), single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S & F 75 mm bore PVC (SWR) Multi floor trap including jointing with solvent cement ( ISI Marked) . complete all as specified and directed.

S&F in repair PVC (SWR) junction single (Single T) radius 110mm bore with access door complete all as specified and directed.

S&F in repair PVC bend of radius 110mm bore with access door complete all as specified and directed.

S&Fin repair PVC bend of radius 75mm bore with access door complete all as specified and directed.

S&F in repairs Vitreous china Squatting pan (Ist quality) , 'Orissa pattern, white, with integral foot rest excluding flushing cistern and flush pipe including connection to trap, to flushing pipe, anti-syphonage pipe, etc complete including making good to floor complete all as specified and directed

S&F in repairs PVC valveless, syphonic action type flushing cistern (Dual action ISI Marked), low level , white, with inlet ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32 mm dia for low level cistern for 10 litres capacity of approved make complete all as specified and directed

S&F in repairs Vitreous China wash basin, white, flat back, size 550x450mm excluding taps, waste, chain and plug and porcelain stopper but including waste coupling of PTMT (min weight 32mm-45gms cutting for pinning in ends of brackets or erecting stand complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan pedestal pattern white (excluding fixing bolts, flushing cistern and flush pipe) including connection to trap, to flushing pipe, anti-syphonage pipe, etc complete complete all as specified and directed.

S & F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25m long flexible tube and ABS wall hook including making connections fixed in position complete in all respect as specified and directed.

S&F in repairs angle stop valve cast copper alloy screwed down high presure screwed both end for iron pipe 15 mm dia fancy type cromium plated (ISI Marked) complete all as specified and directed.

S & F in repairs stop valve cast copper alloy screwed down high presure (concealed type) screwed both end for iron pipe 15 mm dia fancy type cromium plated. complete all as specified and directed.

S&F in repair brass CP bib tap 15mm bore fancy type screwed for iron pipe complete with wall flange complete all as specified and directed.

All as per item No 47 here-in-before but long body type complete all as specified and directed.

S & F in repair CP shower rose with or without swivel joints of 125 mm size with shower arm including fixing to steel pipe or union complete all as specified and directed

S&F in repair CP Grating doom 125mm dia with/without waste hole of steel fixed on floor/nahani trap with cement mortar, complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nut at both ends with washer, 450mm long and fixed complete all as specified and directed.

S & F cast copper alloy, chromium plated Towel Rail 20 mm dia, D-type, 600 mm long fixed with and including Chromimum plated brass screws and wooden plastic cleats Complete all as specified and directed.

S&F in repair Viterous China urinal full stall type, white complete including providing and fixing plugs, bedding urinal against wall in Cm 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; including fixing with waste coupling of PTMT suitable for urinals (min weight 32mm-45gms) and urinal spreader of PTMT any coulour fixing with 15mm dia pipe ,fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe. complete all as specified and directed.

S & F in repair 15mm fancy type chromium plated Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S & F 75mm Stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, inclu nut and bolts and securing ends of stays to wall or roof

S & F 100mm Stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, inclu nut and bolts and securing ends of stays to wall or roof

Taking down existing tar felt and plastering from the roof surface washing down and cleaning the surface with water and rubbish off the premises and M&L 15mm thick cement plaster (1:4) for finshing existing surface and over laying water proofing treatment on top surfaces of roof after cleaning of roof surfaces with water and filling cracks with sealing compound and dried top surface of roof. Apply a coat of cold bituminous primer @ 0.30 liter per Sqm and followed by a layer of APP polymer modified five layered water proofing membrane 3mm thick weight not less than 3.60 Kg/Sqm with non woven polyester reinforcement (weight not less than 150 gm/Sqm) of M/s STP Texsa Ltd or M/s IWL (I) Ltd or M/s STP Ltd. The APP membrane shall be laid with LPG connected torch method. A layer of hot blown bitumen grade 85/25 @ 1.20 Kg/Sqm and a layer of bituminous aluminum paint as final finish @ 0.20 Kg/Sqm shall be applied on top surfaces of APP membrane, Application including overlap, side lap shall be provided as per manufacturer instructions and as specified and directed The side lap and end laps should have overlap of 75mm to 100mm and should be thermo fused together so that it forms a single sheet through out complete all as specified and directed by Engr-in-Charge

M & L 50 mm +/- 25mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded stone agg) mixed withliquid water proofing compound (as per manufacture direction and paid separately) over and incl one coat of cement slurry admixed with acrylic bonding compound SBR Latex liquid polymer as to be used for bonding of new concrete / mortar to old surface as per manufacturer direction and finishing the surface even and fair (without using extra cement) as in roof padding to receive roof treatment complete all as specified and directed.”complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) of size n.exc 1.50 Sqm and removing from site complete all as specified and directed.

All as item No.60 above but exc 1.50 Sqm and n.exc 4.00 Sqm each.

Taking down shutters of any descriptionexc 1.00 Sqm and n.exc 2.00 Sqm each and removing from site complete all as specified and directed.

M&L Solid (100mm x63 mm single rebate) factory made 100% solid WPC brown door frame made from 100% LEAD FREE (Single extruded process) material with density 780 kg/ Cum & manufactured by an ISO: 9001-2015 certified company, all as per specification drawings as directed by Engg-in-Charge. The door frame should be Water Proof, termite proof, fire retardant and having excellent screw holding capacity nd shall be fixed with 6 Nos 150mm long hole fasternerscomplete all as specified and directed.

M&L 30mm thick moulded plain WPC solid door shutter: providing (30mm thick) MOLDED WPC Brown Factory made 100% solid door (Conforming As per IS: 4020) made from 100% LEAD FREE single extruded with 2,4 or 6 raised panel design on the front side with 10mm deep mould on single side with wood grain texture and back side plain with density not less than 600kg/Cum. Manufactured by an ISO: 9001-2015 certified company. The door should be water Water Proof, termite proof, fire retardant and having excellent screw holding capacity complete all as specified and directed.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm ivory colour PVC sheet reinforced with M.S. square tube, S&F in opening as per specification and drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded ivory colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of ivory colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, and 5mm thick x 15mm wide PVC sheet beadings used inside stiles and rails and decorative PVC beading of 10mm x 10mm used instead of exposed portion of PVC sheet beading and suppling & fixing in the frame at site as per specification & drawing.

S&F Anodised aluminium powder coated frame for doors window,partition and ventilatore with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F Anodised aluminium powder coated window and ventilators shutters sliding or fix type, aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,including provision of lock in each door, rollers, anodised aluminum snap beading screws etc. complete all as specified

S&F MS butt hinges 100mm long medium weight cold rolled mild steel complete all as specified and directed.

S&F aluminum anodized barrel tower bolt 200mm long of extruded section complete all as specified and directed.

S&F aluminum anodized sliding door bolt 250mm long with hasp and staples (bolt type) and fixing clips of sheet cast of extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and directed.

S&F aluminum bow handle "D" type anodized 150mm long complete all as specified and directed.

S & F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Hacking out old broken glass of any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/springs clips complete all as specified and directed.

S&F for Glazing with plain sheet glass, ordinary quality, 3 mm thick and glazing with oil putty or aluminium or PVC beading in squares not exceeding 0.5 Sq.m in each pane complete all as specified and directed

S&F for Glazing with frosted sheet glass, ordinary quality, 3 mm thick and glazing with oil putty or aluminium or PVC beading in squares not exceeding 0.5 Sq.m in each pane complete all as specified and directed

S&F in repair MS helical door spring fixed in iron/wooden surface 300mm long including roller and roller plate complete all as specified and directed.

S&F in repairs door stopper aluminium anodized white dale 40mmx40mm and 2mm thick dia 150mm having rubber bush 25mm dia long (high) fixed to door shutter with steel screw complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided not otherwise provided for complete all as specified and directed.

S & F in repair welded steel wire fabric wt not less than n exc 4 Kg per Sqm complete to steel member complete all as specified and directed.

Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 or E 165 includind dismantling existing mild steelwork in any position, complete all as specified and directed.

Preparation of new or previously untreated steel surfaces of any description over 10 cm in width or girth applying two coat of synthetic enamel paint over a coat of red oxide or zinc chrome complete all as specified and directed.

M&L for preparation of old surface on ceiling including brooming down or steel wire brushing scraping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots making the surface even and smooth and applying one coat acrylic distemper (oil emulsion ) on old decorated surfaces using rollers complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of old decorated distempered surfaces on internal walls including brooming down or steel wire brushing scraping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and making the surface smooth by rubbing with sand paper and applying one coat of acrylic distemper (oil emulsion) using rollers of approved tint and make all as specified and directed by Engr-in-Charge.

M&L for preparation of old decorated surface of exterior wall by removing existing treatment with mechanical sander (rpm 1500-2700) along with dust extraction system for clean environment certified by reputed paint manufacturers, then washing the surface with Bleaching powder solution for treatment of fungal growth and applying two coats of exterior anti fungal acrylic emulsion paint (wallmista of Berger paint or equitant in Asian paint, Nerolac etc having three years of performance warranty) over a coat of exterior water based primer of same make all as specified and prescribed by manufacture of paint and as directed at site by Engineer-in-Charge. Note:- (i) The old surface must be prepared in a manner so that there should not be any impression of dent and it should be made even all with a layer of water resistant putty as per manufacture instruction before application of distemper. The cost of materials, labour & T&P required for preparation of surface are demand to be included in the rates quoted. (ii). The work must be got executed through authorised applicator of manufacture after concluding an MoU with manufacture for company back guarantee by the contractor. The authorised applicator of manufacturer shall be got approved from GE before commencement of work. (iii). All the material to be incorporated in the work shall be brought by contractor to MES store yard which will be subsequently issued by department for incorporation in the work to ensure the quantity to be consumed all as per recommendation of manufacture. (iv). After carrying out preparation of surface the same shall be got approved from GE before application of distemper for each building. (v). The colour / shade will be all as approved by GE. (vi) The cost of Scaffolding wherever required are deemed to be included in the rates quoted by the contractor.

M&L for preparing old painted steel and Iron surfaces of any description over 10 cm Width /Girth and applying one coats of synthetic enamel paint of any tint all as directed

Surface dressing n exc 15 cm deep in Hard/dense soil

Excavation in post holes (or similar holes) each n.exc 0.50 cum getting out, returning, filling in and ramming PCC or broken rubble mixed with earth around, in layers n.exc 25 cm, watering and removing surplus soil to a distance n.exc 50 m and making good surface in hard/ldense soil complete all as specified and directed

Excavation in tenches n exc 1.5m in width and n exc 1.5m in depth for foundation etc n exc 10 Sqm on plan and getting in Hard/dense soil

M&L PCC 1:4:8 type D2 (40 mm graded stone aggs) as in fdn filling and mass concrete complete all as specified and directed.

S & FJoist, channel, angle, or tee sections, fixed independently, without connecting plates, etc complete all as specified and as directed

S&F prepainted galvalume aluminum zinc coating GI based plain steel 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /clading to wall, fixed with self tapping screw as specied and as directed.

S & F, Pre- painted galvanium aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and as directed.

M&L for rendering 15mm thick in CM 1:6 on brick or concrete surfaces, finishing the surface even and smooth without using extra cement complete all as specified and directed

M&L preparation of new or previously untreated surface of wall and applying two coats of white wash

Removing excavated material n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

M&L75 mm thick cement concrete type D2 1:4:8 (40 mm graded aggs) as in sub base of floor complete all as specified and directed.

M&L polished rubber moulded coloured machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming IS 15658-2006 of 60mm thickness, M-35 grade laid over and incl 25mm thick sand cushioning complete all as specified and directed.

M&L 40 mm thick cement concrete type B1 1:2:4 (20 mm graded aggs) as in floor finishing cement concrete surface even and smooth with using extra cement (alternative panel) all as specified and directed.

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth, for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc n exc10 sqm on plan and n exc 1.5m in depth and getting out any type of soil.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm inany type of soil complete all as specified and directed.

M & L PCC 1:2:4, type B-0, 40 mm thick in Damp Proof Course to horizontal or vertical surfaces including necessary formwork with using WPC @2% by weight of cement. (Note:- WPC shall be measured and paid separately under respective item as "Supply only".

M&L for two coats of oil bound distemper over a coat of 2mm thick wall putty to newly plastered surface including preparation of surfaces complete all as specified and directed

M & L for preparing newly plastered or previously untreated wall surfaces and applying two coats of cement base paint over one coat of primer complete all as specified and directed.

M&L for rubber moulded coloured glossy finish cement concrete chequered tiles of size 20x20x25mm thick jointed in neat cement slurry and pointed in white or coloured cement and pigment to match the surface of tile as in floor over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed

M & L of 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl 15 mm thick screed bed in cement mortar 1:4 incl full round bull nosing complete all as specified and directed.

M & L for providing reinforced cement concrete nominal mix (type B1 1:2:4, 20mm graded aggregate) as in slabs supported on walls etc all as specified and directed.

M & L TMT bars 10mm dia and over cut to length, bent to shape required incl. cranking, bending and incl. mild steel wire (annealed) not less than 0.9mm dia or securing with clips.all as specified and directed.

M&L use and waste for form work to soffits of suspended concrete slabs for fair finished concrete surface flat surface.

M&L for coloured Glazed ceramic tiles in vertical surfaces 450 x 350x 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement over 10mm thick rendering or bedding layer of cement mortar 1:3 complete all as specified and directed.

S & F Rolled Mild Steel sections confirming to Fe 410 - W (grade E 250 Quality)as in main and cross beams, hip and jack rafters; purlins where connected to common rafters fixed with angle cleats or other connecting plates. Complete all as specified and directed by Engineer in Charge .

S&F for anodised aluminium snap grid frame work for false ceiling (grid size 605 x 605mm) fixed to walls with rawl plugs and screws and hang to roof members with 6mm hanger bar of dia GI wire (upto 1200mm length) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fastners 12.5mm dia 40mm long with and including 12mm thick perforated particle board of 60x60cm in size fixed or laid / inserted to Aluminium frame work complete all as specified and directed.

S&F Aluminum powder coated fixed type windows including suitable nylon beading channel gasket etc complete with following specification :- Frame :- 60mmx40mmx1.80mm Panel :- 4mm thick ACP sheet / 5mm thick tinted/frosted glass of approved colour and design

S & F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet complete all as specified and directed.

S&F aluminum anodized barrel tower bolt 150mm long of extruded section complete all as specified and directed.

Cutting chases, pinning in brick walls and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

S & F vitreous china table top WHB size 640x400x120mm excluding taps, waste, chain and plug and procelin stopper complete all as specified and directed. (Make: Jaquar/Parryware)

S & F in vitreous china wash down water closet pan single piece (pedestal pattern) size 365 x 655 x 760mm UF soft close seat cover fixing accessaries set and accessaries set cistern fittings and S trap 220mm complete all as specified and directed. (Make Jaquar/Parryware)

S&F pillar taps,cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed

S&F CP toilet paper holder with flat recessed type stainless steel fixed to wall with CP brass screw complete all as specified and directed.

S&F brass CP bib tap 15mm bore fancy type screwed for iron pipe complete with wall flange complete all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long incl aluminium alloy bracket and guard rail

S&F 15mm bore dia fancy type, chromium plated angle valves, cast copper alloy,screwed down,high pressure, with crutch , screwed both ends for iron pipe or for unions and fixed

S&F PVC water storage tank cylindrical,triple layer vertical with closed top with threaded cover hoisted and fixed in position tank capacity 500 Ltr with and including ball valve high pressure of PTMT with epoxy coated Aluminum rod and high density plastic ball screwed for 20mm bore of iron pipe and making connection for inlet and outlet and 20mm tank nipple (min weight 45gm) suitable for HDPE water tank complete all as specified and directed.

S&F gun metal globe gate valves 20mm dia with iron wheel head, screwed both ends for iron pipe etc complete

Excavation in trenches n. exc 1.5m wide and n. exc 1.5m in depth in soft/loose soil for foundation, etc or for shafts, wells, cesspits, manholes, pierholes, etc and getting out complete all as specified and directed

M&L RCC (nominal mix) Type B1 1:2:4 (20mm graded aggregate) as in columns, pillars, piers, posts and struts as specified and directed

M&L Cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in foundations or mass concreteor sub base complete all as specified and directed

M&L for use and wste of form work to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface, square or retangular of concrete complete all as specified and directed complete all as specified and directed.

M & L TMT bars 6mm to 8mm dia cut to length, bent to shape required incl. cranking, bending and incl. mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Disconnecting the electrification and taking down DBs (any type of SPN DBs) and making good to the disturbed surfaces to match the existing surface all as specified and as directed by EIC. Note - Temporary power supply shall be provided by contractor.

Taking down U/S submain wiring aluminium etc and making good the disturbed surfaces of walls/ floor etc matching with the existing surface.

M&L for sub-main wiring (concealed) with two single core 6 sq mm FRLSH PVC insulated unsheathed stranded copper conductor cable drawn through including chasing cutting in any type of massinory including 25 mm dia non-metallic PVC conduit fixed in wall including 6 sq mm copper earth continuity wire, accessories and connecting to earth dolly complete, all as specified and as directed by EIC.

Taking down carefully aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pedants, regulators, sockets, light fitting etc.. and making good the disturbed surfaces of walls/ floor etc matching with the existing surface all as specified and as directed by EIC.

Material & Labour for following type Point Wiring controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with contineous earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealed PVC conduit MMS ,duly concealed to wall/floor or above false ceiling with fittings(ISI marked) not less than 20 mm dia (Color coding of wires shall be Phase, neutral and earth wire all as specified ) sunk Metal flush box with and incl decorative polycarbonate frame for housing Modular Switches, sockets , fan regulators etc including white cover cover plate complete all as specified and directed. Note:- i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates).

One light point controlled by one switch.

One ceiling fan point controlled by one switch.

One exhaust fan pointcontrolled by one switch.

One 3 pin socket outlet 5 Amps on the same board.

One 3 pin socket out let 5 Amps on the independent board.

All as per Item No. 136 above but 2.5 Sq mm multi stranded copper conductor with 2.5 Sq mm copper earth continuity wire connected to earth duly complete for one 15A Socket on Independent board all as specified and as directed by EIC.

Supply and fixing surface & wall mounted LED batten 4 feet with 1x20 Watt indoor decorative luminaries with and including electronic driver and 1x20 watt LED Lamp, pre-wired including necessary electric connection with copper flexible PVC cable of 0.50 Sq mm 3 core not more than 1 mtr in length from ceiling rose/connector to light fitting complete all as specified and directed.

S & F angle lamp holder, PVC Polycab type with back plate suitable for batten fittings complete including fixing of 9/10 watt LED bulb all as specified.

Supply and fixing step socket type modular fan regulator 120/280 V , 100Watt all as specified and as directed.

Supply and fixing modular socket, 6A -2/3 pin combined 2 module ISI marked 230 volts, 50 Hz all as specified and directed by Engr- in-charge.

S & F Switch Modular single pole, one way 6 Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge.

Supply and fixing modular socket, 6A/16A -2/3 pin combined 2 module 230 volts 50 hz all as specified and directed by Engr- in-charge.

Supply and fixing switch modular , one-way 16Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge.

M & L for ceiling rose, surface bakelite, 65 x 50 mm, three terminals all as specified and as directed.

S & F sheet metal enclosures for SPN DB's with double glazed door for incorporating MCBs,IP-43 , 8 way with 200 amps rated busbar, 240 volts, as per IS-8623 all as specified and as directed.

S & F sheet metal enclosures for TPN DB's with double glazed door for incorporating MCBs,IP-43 , 6 way TPN with 200 amps rated busbar, 415 volts, as per IS-8623 all as specified and as directed.

S & F MCBs TPN 63 amps, 415 volts, 50 Hz, 'C' curve including necessary incoming and out going electric connection with suitable size of copper lugs all as specified and as directed by Engr-in-Charge.

S & F MCBs SPN 32 amps, 240 volts, 50 Hz, 'C' curve including necessary incoming and out going electric connection with suitable size of copper lugs all as specified and as directed by Engr-in-Charge.

S & F MCB SP, 6 to 32 Amps, 240 volts, 50 Hz, 'C' curve including necessary incoming and out going electric connection with suitable size of copper lugs all as specified and as directed by Engr-in-Charge.

M & L for Earthing complete with galvanised steel pipe electrode, 600 x 600 x 6.3 mm thick, buried directly in ground (earth pit not less than 2.25 mtrs deep below nominal ground level) with top edge of the plate not less than not less than 1.5 metres below nominal ground level connected to galvanised earthing lead of 4 mm dia of iron or steel wire all as shown in electrical plate No. 5 all as specified and as directed. Note :- the cost of excavation and earth work PCC pit and CI cover funnel & watering pipe, wiremesh, charcoal dust and common salt shall be deemed included in the unit rate for earthing all as specified and as directed by EIC.

Taking down old unserviceable existing service/UG cable all as specified and as directed by EIC.

Material and labour for XLPE insulated,LT armoured electric cable with aluminium standed conductor 1100 volts grade,cross-sectional area 35 sqmm ,3.5 core laid in trenches/pipes/ducts/wall/boarings with necessary cable lugs and glands,nuts,bolts and washers etc and testing complete all as specified and directed.

Material and labour for XLPE insulated,LT armoured electric cable with aluminium standed conductor 1100 volts grade,cross-sectional area 10 sqmm ,2 core laid in trenches/pipes/ducts/wall/boarings with necessary cable lugs and glands,nuts,bolts and washers etc and testing complete all as specified and directed. (Note- Cable will be laid on wall or on roof for electric supply to solar water system ).

M & L for brick sub class 'B' 250mm x 115mm x 0.75mm and laid in trenches as in protection of UG cable complete all as specified and directed.

Supply and filling in and speading unwashed river sand for cushioning and covering the under ground cables in trenches and punning to provide required cover complete all as specified in SSR Part-I and as directed.

M & L for 50mm bore GI pipe (Light grade) laid under road or fixed with pole/wall of culvert as in protection of UG cable incl necessary MS clamp and complete all as specified and directed.

Boaring holes horizontally under Road without damaging the surface of road (minimum 1.0 Mtr bellow the road surface) with the help of GI tubing of any dia not exc 100 mm dia for passing of UG cable all as specified and as directed.(GI Pipe laid shall be measured seperately)

Supply, fabricated and and fixing of street light bracket made out of GI pipe 1.0 Mtr long, 32 mm dia medium grade bent to shape as directed including clamps made out of 40 mm x 6 mm flat for fixing bracket suitable for steel tubular poles including nuts and bolts, washers and other connected items of required size including painting with one coat of aluminium paint over a coat of red oxide/primer all as specified and as directed.

M & L for LED Bldg Security light Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

M & L for disconnecting electric supply, taking down fan, cealing cable ends, dismantling blades carefully after unscrewing nuts and bolts of ceiling fan any size from existing position and bringing to AGE E/M store yard for clelaning all dusts, oiling, greasing all as specified and as directed by EIC.

S & F vertical load line in sheet metal enclosures MCCB TPN DB's with double door for incorporating MCCB as incomer and MCBs SP/SPN as outgooing , IP-43 , TPN 4 way with 200 amps rated busbar, 440 volts, as per IS-8623 including taking out old UNSV DB and making good the disturbed surface of wall and match with the existing surface compelte all as specified and as directed. (Note- MCCB 3 pole 63 amps as main incomer will be included in quoted rate)

M&L for sub-main wiring concealed/surface conduit with 4x core 16 sq mm FRLS PVC insulated unsheathed stranded copper conductor cable drawn through including chasing cutting in any type of massinory including 40 mm dia non-metallic PVC conduit MMS fixed in wall including 2x 16 sq mm copper earth continuity wire, accessories and connecting to earth dolly complete, all as specified and as directed by EIC.

Taking down old serviceable water heater storage type, electric operated, capacity 25 litres, complete with all connected accessories and M & L for refixing the same in original position and connecting with water supply pipe line and all water and electrical connection all as specified and directed.

NOTES :- 1. For the items for which specifications not mentioned any where in the tender, the BIS specifications shall be followed.

JBN CONSTRUCTION (BID ID -3114540)