Renovation of Kashipur quarter for the purpose of Kashipur CCC, surrounding development, sanitary and plumbing and water supply arrangement with allied civil works at premises of Kashipur 33/11 KV sub-station, Dist.-Purulia.

Clearing compound premises of shurbs, plants, jungles etc. by cutting and removing as directed (Specific permission of Engineer-in-Charge prior to execution will be necessary). (Payment to be made on area cleaned)

Surface Dressing of the ground in any kind of soil including removing vegetation inequalities not exceeding 15 cm depth and disposal of the rubbish within a lead upto 75 m as directed.

Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m.a). In ground floor including roof.

Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed.

Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. Depth of excavation not exceeding 1,500 mm.

Add extra for excavation in moorum soil.

Add.extra for cutting lateriate/ sandstone. By cutting with chisel

Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work). With earth obtained from excavation of foundation.

Earth work in filling in compound, tank, low land, ditches etc. with good earth, in layers not exceeding 150 mm. including breaking clods and consolidating the same by ramming and dressing complete. (Payment will be made on profile measurement beforeand after the work).(iii) With carried earth arranged by the contractor within a radius exceeding 5 km. but not exceeding 10 km. including cost of carried earth.

Filling in foundation or plinth by Fine Sand in layers not exceeding 150 mm. as directed and consolidating same by thorough saturation with water ramming complete, including the cost of supply of sand. (Payment to be made on measurement of finished quantity). Do by fine sand.

Single brick flat soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand.

Cement concrete with graded stone ballast (40 mm.size excluding shuttering). In ground floor Pakur variety 1:3:6 proportion.

Ordinary Cement Concrete( mix.1:2:4) with graded stone chips(20 mm.nominal size) excluding shuttering and reinforcement, if any, as per relevant I.S.Codes Pakur variety.

Ordinary Cement Concrete( mix.1:1.5:3) with graded stone chips(20 mm.nominal size) excluding shuttering and reinforcement if any,in ground floor as per relevantI.S.Codes Pakur variety. In ground floor

R.C.C. (mix.1:1.5:3) 1st floor

R.C.C. (mix.1:1.5:3) 2nd floor

Hire and labour charges for shuttering with centreing and necessary staging upto 4 m. using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fitting, fixing and striking out after completion of works. (upto roof of ground floor) (When the height of a particular floor is more than 4 m. the equivalent floor ht. shall be taken as 4 m. and extra for works beyond the initial 4 m. ht. shall be allowed under 12(e) for every 4 m. or part there of.). steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work. Ground Floor.

In 1st. Floor

In 2nd Floor

25 mm. to 30 mm. thick wooden shuttering without staging in foundation.

Brick work with 1st class bricks in cement mortar (1:6) . In superstructure, ground floor

In superstructure, 1st floor.

In superstructure, 2nd floor.

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) In G.Floor.

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) In 1st.Floor.

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) In 2nd.Floor.

Extra for using approved H.B netting in every third layer in any floor

Labour for Chipping of concrete surface before taking up Plastering work.

Cleaning the concrete surface by removing dirt and debris, marking defective locations and removing loose concrete by careful stripping untill hard surface is exposed, cutting the concrete to regular shape, wire brushing the exposed surface and removing debris from site complete as per direction of the Engineer - in - Charge.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints or rougening of concrete surface, including throating, nosing and drip course where necessary. (excluding cost of chipping over concrete surface). With 1:6 cement mortar. 20 mm. thick plaster. In Ground floor.

20 mm. thick plaster In 1st floor.

20 mm. thick plaster In 2nd floor.

20 mm. thick plaster In 3rd floor.

15 mm. thick plaster In Ground floor.

15 mm. thick plaster In 1st floor.

15 mm. thick plaster In 2nd floor.

15 mm. thick plaster In 3rd floor.

With 1:4 cement mortar. 10 mm. thick plaster In Ground floor.

10 mm. thick plaster In first floor.

10 mm. thick plaster In second floor.

10 mm. thick plaster In third floor.

Neat cement punning about 1.5 mm. thick in wall, dado, window, sills, floor, drain etc. NOTE : Cement 0.152 cu.m. per 100 sq.m.

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups,binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape,placing in proper position and binding with 16 gauge black annealed wire at every inter-section, complete as per drawing and direction. Tor steel/Mild steel (SAIL/TATA/RINL). For works in foundation, basement and upto roof of ground floor / upto 4m.

Reinforcement 1st floor

Reinforcement 2nd floor

Supplying and laying Polythene Sheet (150gm/sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches.

Supplying fitting and fixing 15 to 18 mm thick Marble slab/Tile in riser of step or skirting (upto 300 mm ht) over 15mm (avg) thick base of Cement mortar (1:2) laid with white cement slurry @ 4.4 kg/ Sq.m at back side of marble and jointed with white cement slurry @ 2.2 kg/ Sq.m with necessary pigments including grinding and Granite Polishing. [White cement and Pigment to be supplied by the Agency] With Makrana plain pink / Adranga Pink / Garbh Gulabi / Udaypur pink / Udaypur Green / Black Bhaslana Area of each Slab/tile upto 0.3 sq.m. (a)Ground Floor

Extra cost of labour for prefinished and premoulded Nosing to treads of steps, railing, window sill etc. of Marble Stone.

Supplying fitting and fixing 15 to 18 mm thick Marble slab/Tile in riser of step or skirting (upto 300 mm ht) over 15mm (avg) thick base of Cement mortar (1:2) laid with white cement slurry @ 4.4 kg/ Sq.m at back side of marble and jointed with white cement slurry @ 2.2 kg/ Sq.m with necessary pigments including grinding and Granite Polishing. [White cement and Pigment to be supplied by the Agency] With Makrana plain pink / Adranga Pink / Garbh Gulabi / Udaypur pink / Udaypur Green / Black Bhaslana Area of each Slab/tile upto 0.3 sq.m. First Floor

Extra cost of labour for Marble Stone Floor in treads of Steps.

Supplying and laying true to line and level vitrified tiles of approved brand (size not less than 600 mm X 600 mm X 10 mm thick) in floor, skirting etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry back side of tiles using cement @ 2.91Kg./sqM or using polymerised adhesive (6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per sqM below mortar only, joints grouted with admixture of white cementand colouring pigment to match with colour of tiles / epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge.(White cement, synthetic adhesive and grout material to be supplied by the contra conc With application slurry @1.75 kg/ Sq.m, 20 mm sand cement mortar (1:4) & 2 mm thick cement slurry at back side of tiles, 0.2 kg/ Sq.m white cement for joint filling with pigment Deep Colour & White. Ground floor.

Supplying and laying true to line and level vitrified tiles of approved brand (size not less than 600 mm X 600 mm X 10 mm thick) in floor, skirting etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry back side of tiles using cement @ 2.91Kg./sqM or using polymerised adhesive (6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per sqM below mortar only, joints grouted with admixture of white cementand colouring pigment to match with colour of tiles / epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge.(White cement, synthetic adhesive and grout material to be supplied by the contra conc With application slurry @1.75 kg/ Sq.m, 20 mm sand cement mortar (1:4) & 2 mm thick cement slurry at back side of tiles, 0.2 kg/ Sq.m white cement for joint filling with pigment Deep Colour & White, 1st Floor.

Labour for taking out door and window frame including shutter for repair or replacement of different parts of the frame & refixing the same including mending good all damaes complete. (Concrete and brick work for mending damage will be paid separately).

Collapsible gate with 40mm x 40mm x 6mm Tee as top and bottom guide rail, 20mm x 10mm x 2mm vertical channels 100mm apart in fully stretched position 20mm x 5mm M.S. flats as collapsible bracigs properly rivetted and washered including 38mm steel rollers including locking arrangements, fitted and fixed in position with lugs set in cement concrete and including cutting necessary holes, chasing etc. in walls, floors etc. and making good damages complete. (Payment will be made on the area of the gate covered by two guard rails and two extreme channels)

Supplying, fitting and fixing steel rolling shutter profile type with 18 B.G . of approved type steel latche section 75mm wide, fitted with coil wire spring to necessiate the fitting of required Nos. of C.I. Pulleys on heavy type solid drawn seamless steel tube complete with locking arrangements both inside and outside specially builtup side guide channels including providing a hood for the steel rollingshutter in the room, painting two coats of approved aluminium paint over a coat of red lead primer complete.

M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs. In ground floor.Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr

M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in 1st floor. Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr

M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in 2nd floor. Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr

Supply, fitting & fixing M.S. clamp for fixing door and window frame made of flat bent bar, end bifurcated, fixed in cement concrete with stone chips (1:2:4) fitted and fixed complete as per direction. (Cost of cement concrete will be paid separately). 40mm. X 6mm, 250mm. Length.

Anodised aluminium butt hinges of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 205/66) and fitted and fixed with cadmium plated screws: (vi) 125 x 63 x 3.2mm.

Hydraulic Door Closer of approved quality as per I.S.I. standard fitted and fixed complete. (a) Heavy type (I.S.I. size 3)

Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16 mm dia rod with centre bolt and round fitting. 300 mm long.

Supplying solid flush type doors of deluxe decorative (both side) quality, conforming to I:S 2202 timber frame consisting of top and bottom rail and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 27.5mm wide battens places both ways in order to made the door of solid core and internal lipping with teak, mahogony or rose wood approved decorative veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing the shutters in position but excluding the cost of hinges and other fittings in ground floor: 35mm thick shutters (single leaf)

Scantling upto 50mm wide and 12mm thick (chamfering or rounding) for ceiling/partion battens including fitting, fixing in position with washers, coach screws etc. complete.: ordinary teak

Supplying, fitting and fixing fibre reinforced polymer (FRP) Composite door frame as per approved section with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to safisfy IS: 4020 door testing performance criteria.66mm x 70mm

Supplying, fitting & fixing fibre reinforced polymer (FRP) Composite door shutters as per approved design with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to satisfy IS:4020 door testing performance criteria. In ground floor. 32 mm thick.

Spplying Profiles of required section made of Aluminium Alloy Extrusions conforming to I.S.: 732-1983 and I.S.: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finished conformating to I.S.: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - In- Charge. (Payment will be made on finished length of the work). In 10-12 Micron thickness Annodizing film. Natural white. Movable door shutter.Door frame: (Top & sides).

Door Shutter : Top rail.

Door Shutter : Bottom rail.

Door Shutter : Lock rail

Door Shutter : Door vertical

Door Shutter : Glazing clip.

3 track sliding window bottom frame.

Top & side frame

Shutter for all track sliding window.i) Bottom & Top member.

Style side member

Interlock member

Fixed partitions. (Unsupported length of vertical member over 1.5 mtr. Height of both ends of vertical member restrained but panels more than/over 0.9 sq.m.) Top , bottom & side member.

Intermediate member.

Glazing clip.

Supplying PVC rollers for sliding windows as per direction of Engineer-in-charge.

Supplying EPDM gusket of approved make and brand as per direction of Engineer in charge.a) EPDM / weather gasket for outer frame and mullion.

weather gasket / wool pile for door vertical.

Labour charge for fabrication and installation of composite door, window , partitions made from annodized extruded alloy aluminium sections for the following units: Partly glazed partly panelled or fully glazed single leaf aluminium swing door made of extruded and annodized alloy aluminium sections, fabrication including cutting to proper shape and size, drilling and aligning, fitted with heavy duty hydraulic action floor sping placed in the floor with mending damages,with top pin assembly of approve make and brand, fitted with in built locking arrangement, flush bolt, glazing clips and all other necessary fittings, fixtures, adhesives and joineries, cutting glass of approved make to requisite shape and size fitting with dry set neoprene or EPDM gasketing, cutting to requisite shape and size panel board (prelaminated particle block) fixing them with glazing clips as per drawing, specification and direction of Engineer in charge. In ground floor.

Labour charge for fabrication and installation of composite door, window , partitions made from annodized extruded alloy aluminium sections for the following units: Partly glazed partly panelled or fully glazed single leaf aluminium swing door made of extruded and annodized alloy aluminium sections, fabrication including cutting to proper shape and size, drilling and aligning, fitted with heavy duty hydraulic action floor sping placed in the floor with mending damages,with top pin assembly of approve make and brand, fitted with in built locking arrangement, flush bolt, glazing clips and all other necessary fittings, fixtures, adhesives and joineries, cutting glass of approved make to requisite shape and size fitting with dry set neoprene or EPDM gasketing, cutting to requisite shape and size panel board (prelaminated particle block) fixing them with glazing clips as per drawing, specification and direction of Engineer in charge. In First floor

Labour charge for fabrication and installation of composite door, window , partitions made from annodized extruded alloy aluminium sections for the following units: Partly glazed partly panelled or fully glazed single leaf aluminium swing door made of extruded and annodized alloy aluminium sections, fabrication including cutting to proper shape and size, drilling and aligning, fitted with heavy duty hydraulic action floor sping placed in the floor with mending damages,with top pin assembly of approve make and brand, fitted with in built locking arrangement, flush bolt, glazing clips and all other necessary fittings, fixtures, adhesives and joineries, cutting glass of approved make to requisite shape and size fitting with dry set neoprene or EPDM gasketing, cutting to requisite shape and size panel board (prelaminated particle block) fixing them with glazing clips as per drawing, specification and direction of Engineer in charge. In Second floor

(b) Glazed aluminium sliding windows made of extruded and annodized alloy aluminium sectios, fabrications, including cutting to proper shape and size, drilling and aligning of window shutter frame fitted with in built locking arrangements, sliding rollers and other necessary fittings, fixture, adhesives and joineries along with extruded neoprine or EPDM gasketing in between window frame and masonry work (walls, column, beam.lintels etc.) as well as between glass and shutter frame for fixing glass and Polysulphide sealant and in between shutter and window frame where necessary including cutting to requisite size and fixing glass as per drawing, specification and direction of EIC. The rate includes the hire charge of all tools and plants, including all incidental charges, adhesive, joineries such as screw, cleat angle etc. but excluding the cost of extruded aluminium sections, glass, neoprene /EPDM gasket, locking arrangement and rollers. 3/4 track sliding window. In ground floor

(b) Glazed aluminium sliding windows made of extruded and annodized alloy aluminium sectios, fabrications, including cutting to proper shape and size, drilling and aligning of window shutter frame fitted with in built locking arrangements, sliding rollers and other necessary fittings, fixture, adhesives and joineries along with extruded neoprine or EPDM gasketing in between window frame and masonry work (walls, column, beam.lintels etc.) as well as between glass and shutter frame for fixing glass and Polysulphide sealant and in between shutter and window frame where necessary including cutting to requisite size and fixing glass as per drawing, specification and direction of EIC. The rate includes the hire charge of all tools and plants, including all incidental charges, adhesive, joineries such as screw, cleat angle etc. but excluding the cost of extruded aluminium sections, glass, neoprene /EPDM gasket, locking arrangement and rollers. 3/4 track sliding window. In first floor

(b) Glazed aluminium sliding windows made of extruded and annodized alloy aluminium sectios, fabrications, including cutting to proper shape and size, drilling and aligning of window shutter frame fitted with in built locking arrangements, sliding rollers and other necessary fittings, fixture, adhesives and joineries along with extruded neoprine or EPDM gasketing in between window frame and masonry work (walls, column, beam.lintels etc.) as well as between glass and shutter frame for fixing glass and Polysulphide sealant and in between shutter and window frame where necessary including cutting to requisite size and fixing glass as per drawing, specification and direction of EIC. The rate includes the hire charge of all tools and plants, including all incidental charges, adhesive, joineries such as screw, cleat angle etc. but excluding the cost of extruded aluminium sections, glass, neoprene /EPDM gasket, locking arrangement and rollers. 3/4 track sliding window. In Second floor

Partly glazed and partly panelled partition or fixed glazing made of extruded and anodised alloy aluminium sections, fabrications after cutting to proper shape and size, drilling and aligning fitted with inbuilt locking arrangement cutting the glass / board (prelaminated / particle / block) to requisite shape and size moulding the edges fitted and fixed glazing clips and dry set neoprine /EPDM gasket, along with all other necessary arrangements for fixing the partition to walls, floors, beams, columns polysulphide sealant for water proofing if necessary complete in all respect as per drawing and specifications and direction of the Engineer in charge. I) For partitions using section of size: a) 63.50 mm x 38.10 mm. In ground floor.

Partly glazed and partly panelled partition or fixed glazing made of extruded and anodised alloy aluminium sections, fabrications after cutting to proper shape and size, drilling and aligning fitted with inbuilt locking arrangement cutting the glass / board (prelaminated / particle / block) to requisite shape and size moulding the edges fitted and fixed glazing clips and dry set neoprine /EPDM gasket, along with all other necessary arrangements for fixing the partition to walls, floors, beams, columns polysulphide sealant for water proofing if necessary complete in all respect as per drawing and specifications and direction of the Engineer in charge. I) For partitions using section of size: a) 63.50 mm x 38.10 mm. In 1st floor.

Supplying concealed type heavy duty PVC Headed aluminium Tower Bolt for doubleleaf doors as per approved make and brand as per direction of Engineer in charge. 300mm long

Supplying bubble free Float Glass of approved make and brand conforming to IS: 2835-1987. (a) iii) 5mm thick clear glass.

(b) i) 4mm thick clear glass.

Providing and fixing exterior quality Aluminium Composite Panel (ACP) wall cladding on existing Al. /MS frame work with GI brackets, ACP fixed on the existing frame work by folding the edges of ACP panel (Engraving the rear surface of ACP sheet) with CP angles, cleats and strainless Steel screws forming groves at the periphery of ACP panel. Such grooves filled with foam and silicon sealant etc. complete with all materials (but including the cost of silicon sealant), labour, scaffolding and all other incidental charges complete in all respect as per specification and direction of Engineer-in-charge. (Mode of payment is on finished surface area of ACP). (b) 4 mm thick (0.50mm Al.+3.0mm LDPE +0.50mm Al. PVDF coating)

Filling the gap in between aluminium frame & adjacent RCC / Brick/ Stone work by providing weather silicon sealant over 6mm dia backer rod of approved quality as per architectural drawings and direction of Engineer-in-Charge complete. Upto 5 mm depth and 5 mm width. In ground floor.

Filling the gap in between aluminium frame & adjacent RCC / Brick/ Stone work by providing weather silicon sealant over 6mm dia backer rod of approved quality as per architectural drawings and direction of Engineer-in-Charge complete. Upto 5 mm depth and 5 mm width. In First floor.

Filling the gap in between aluminium frame & adjacent RCC / Brick/ Stone work by providing weather silicon sealant over 6mm dia backer rod of approved quality as per architectural drawings and direction of Engineer-in-Charge complete. Upto 5 mm depth and 5 mm width. In 2nd floor.

Supplying 4-Lever Mortice Lock or any approved make and brand as per direction of the Engineer- in -charge. 150 mm.

Supplying Heavy Duty Aluminium Handle (EBCO Type) Natural White.

Door stopper.(Brass)

Rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand (1.5 mm thick)

Scraping of moss, blisters etc.thoroughly from exterior surface of walls necessitating the use of scraper, wire brush etc. (Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge)

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(b) On steel or other metal surface.With other than hi-gloss of approved quality- (iv) Two coats (with any shade except white)

Applying Interior grade Acrylic Primer of approved quality and brandon plastered or cencrete surface old or new surface to receiveDistemper/ Acrylic emulsion paint including scraping and preparingthe surface throughly, complete as per manufacturer's specification andas per direction of the EIC.ii) Solvent based interior grade Acrylic Primer

Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty: (Two coats). i) Standard Quality

Applying Exterior grade Acrylic Primer of approved quality and brand on plastered or concrete surface (old or new) to receive decorative textured ( matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface thoroughly,complete as per manufacturer's specification and as per direction of the EIC. In ground floor. (b) Two Coats

Applying Exterior grade Acrylic Primer of approved quality and brand on plastered or concrete surface (old or new) to receive decorative textured ( matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface thoroughly,complete as per manufacturer's specification and as per direction of the EIC. In First floor. (b) Two Coats

Applying Exterior grade Acrylic Primer of approved quality and brand on plastered or concrete surface (old or new) to receive decorative textured ( matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface thoroughly,complete as per manufacturer's specification and as per direction of the EIC. In 2nd floor. (b) Two Coats

Applying Exterior grade Acrylic Primer of approved quality and brand on plastered or concrete surface (old or new) to receive decorative textured ( matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface thoroughly,complete as per manufacturer's specification and as per direction of the EIC. In 3rd floor. (b) Two Coats

Protective and decorative Acrylic exterior Emulsion paint of approved quality,as per manufacturer's specification & as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In ground Floor ( Two Coat ). b) Premium 100% Acrylic Emulsion

Protective and decorative Acrylic exterior Emulsion paint of approved quality,as per manufacturer's specification & as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In 1st Floor ( Two Coat ). b) Premium 100% Acrylic Emulsion

Protective and decorative Acrylic exterior Emulsion paint of approved quality,as per manufacturer's specification & as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In 2nd Floor ( Two Coat ). b) Premium 100% Acrylic Emulsion

Protective and decorative Acrylic exterior Emulsion paint of approved quality,as per manufacturer's specification & as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In 3rd Floor (Two Coat ).b) Premium 100% Acrylic Emulsion.

Supplying & laying 3mm thick pre-fabricated plastomeric water proofing membrane conforming to EN 12311-1 & ASTMD 5147, manufactured with atactic poly propylene (APP) modified premium grade asphalt , specially reinforced with non-woven polyester core with polyester reinforcement @160 gms per sqm & both faces covered with thermo-fusible polyethylene film /MineraL on top face over a coat of primer @ 0.40 lit/sqm of manufacturer's specification on smooth,clean dry surface prepared wherever required.Lap joint shall be provided of 75 mm in longitudinal & 100 mm in transverse direction and fused using LPG/ Propane torch employing extra care ensuring full bondage, complete removal of entrapped air and sealing edges into grooves in appropriate manner as per direction of Engineer -in-charge all complete including materials,labour and applicable taxes. (Payment shall be made on the basis of finished surface area.). Membrane Property: Softening Point > 150 deg C, Cold Flexibility < -6 deg C, Tensile Strength, N/cm : 600 (longitudinal), 450 (transverse), Tearing Strength, N: 300 (longitudinal), 200 (transverse).

Supplying, fitting and fixing PVC pipes of approved makeof (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately). For Exposed work. PVC Pipe. 15 mm dia.

20 mm dia.

25 mm dia.

32 mm dia

For Underground work. 32mm dia

Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only). a) 20 mm. dia.

b) 25 mm. dia.

c) 32 mm dia

Supplying, fitting and fixing bib cock or stop cock. Chromium plated angular Stop Cock with wall flange(Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand).

Chromium plated Bib Cock with wall flange (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand).

Supplying, fitting and fixing pillar cock of aooroved make. CP Pillar Cock - 15 mm.(Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand).

Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc.

Supply of UPVC pipes ( B type ) & fittings conforming to IS 13592-1992. a) Single socketed 3 mtr. Length. (110 mm)

(b) Single socketed 3 mtr. Length. (75 mm)

c) Plain Tee (110 mm)

d) bend 87.5 degree (110mm)

e) Door bend ( T.S ) (110 mm)

h) Plain floor Trap with top tile & stainer. (75 mm)

i) Vent Cowl (110mm)

j) W.C.Connector ( 450 mm long ) W/lipring (75mm)

k) 125X110 P trap with w.c ring. ( 75 mm )

Taking out rain water down pipe.

Dismantling H.C.I. pipe with fittings including melting lead caulked joints. (iii) 100 mm

Labour for dismantling G.I. pipe with fittings. (i) 15 mm

Labour for dismantling G.I. pipe with fittings. (ii) 20 mm

Labour for dismantling G.I. pipe with fittings. (iii) 25 mm

Labour for dismantling G.I. pipe with fittings. (iv) 32 mm

Dismantling Orissa pattern W.C. including taking out of base concrete, if necessary, complete.

Dismantling wash basin with brackets with or without waste fittings.

Dismantling sink with brackets with or without waste fittings.(ii) Above 450 mm and upto 600 mm length

Dismantling pillar cock of wash basin.

Dismantling G.I. tank including disconnecting pipe connection.

Lowering G.I. tank (upto and including 1812 litre capacity).(a) From 1st story to G.L.

Lowering G.I. tank (upto and including 1812 litre capacity).(a) From 2nd floor to 1st floor.

Lowering G.I. tank (upto and including 1812 litre capacity).(a) From 3rd floor to 2nd floor.

Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap (excluding cost of concrete for fixing). 580 mm X 440 mm

Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc.With 'S' trap

Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete. Polythene Flush Pipe

Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I. specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm.

Supplying, fitting and fixing towel rail with two brackets. Alluminium. 25 mm. dia. and 600 mm. long.

Supplying, fitting and fixing soap holder. PTMT (Prayag or equivalent)

Wash basin vitreous china of approved make (without fittings) supplied,fitted and fixed in position on 75mm X 75 mm X 75 mm wood blocks and C.I. brackets including two coats of painting of C.I. brackets . (iii) 630 mm X 450 mm size

Supplying, fitting and fixing Stainless steel Sink complete with waste fitting & two coats of painting of CI brackets. 530 mm X 430 mm X 180 mm.

Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete.(iii) Corner urinal 440 mm X 345 mm X 250 mm

Supplying, fitting & Fixing approved brand PVC connector white flexible with both ends coupling with heavy brass C.P. nut 15 mm dia. 600 mm long.

Supplying, fitting & Fixing 32 mm dia PVC waste pipe with PVC Coupling at one end fitted with necessary clamps. 1050 mm long.

Constructing inspection pit of inside measurement 600 mm. X 600 mm. X upto 600 mm. (depth) with 250 mm. thick 1st class brick work in cement mortar (1:4) on all sides, bottom of the pit consisting of 100 mm. thick cement concrete (1:3:6) with stone chips over a layer of jhama brick flat soling , 15 mm. thick (1:4) cement plaster to inside walls and out-side walls upto G.L. and 20 mm. thick (1:4) cement plaster to bottom of the pit, providing necessary invert with cement concrete (1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm. thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm. thick cement plaster (1:4) in all external surface of the slab and one 560 mm. dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils after work complete in all respect with all costs of labour and materials. With Pakur variety (SAIL/TATA/RINL)

Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm. dia. R.C.C. manhole cover (heavy type) of approved make supplied, fitted and fixed in the 100 mm. thick R.C.C. (1:1.5:3) top slab with necessary fittings, 20 mm. thick cement plaster (1:4) with neat cement finish to the internal surfaces and 15 mm. thick cement plaster (1:4) to outside wall upto 200 mm. below G.L. floor finished with 25 mm.thick grey artificial stone over 100 mm. thick R.C.C. (1:1.5:3) bottom slab including supplying, fitting and fixing all necessary specials, fittings, S.W. tees , C.I. foot rest etc. including excavation earth in all sorts of soil, shoring, bailing out and pumping out water as necessary, ramming, dressing the bed and refilling the sides of the tanks with earth, removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials. For 30 users. With Pakur variety.(SAIL/TATA/RINL)

Construction of circular well soak 2.5 mtr. deep in all types of sundry soils with dry brick work upto 1.6 mtr. from the bottom having 150 mm. intermediate cement brick work (4:1) upto 0:90 meter from top with 20 mm. thick cement plastering (4:1) to inside face up to the depth of cement brick work 15 mm. thick cement plaster (4:1) on outer face from to of the well up to G.L. and 10 mm. thick cement plaster (4:1) on top of the R.C.C. cover slab including filling bottom 1 meter of inside of the well with jhama metal (50 mm. to 63 mm. size) including R.C.C. cover slab of 100 mm. thickness with cement conc. (3:1.5:1) with stone chips with necessary reinforcement and shuttering including one 560 mm. dia R.C.C. manhole cover heavy type of approved make supplied, fitted and fixed in the cover slab with necessary fittings making necessary arrangement for pipe connection(s) excavation of well including shoring dewatering and removing the cecess earth from the premises as per direction complete in all respect with all costs of labour and materials with 250mm. Thick dry brick work and 250mm. Thick cement brick work (6:1) and 1.00 M. inside dia.(SAIL/TATA/RINL)

Supplying, fitting & fixing UPVC pipes A-type and fittings conforming to IS:13592-1992 with all necessary clamps, nails, including making holes in wall, floor etc. cutting trenches in any soil, thorough masonry conc. structure etc. if necessary and mending good damages including jointing with jointing materials (Spun yarn, Volamoid / bitumen / M. Seal etc. complete. UPVC pipes. 110 mm. dia

(ii) Plain Tee ( 110 mm dia )

(iii) Bend 87.5 degree

(ii) Shoe – 110 mm. dia

Supplying, fitting and fixing Stainless Steel railing consist of 38mm dia and 900mm height vertical balustrade at every two alternative steps, 50mm dia top rail, 3 (three) nos. 19mm dia horizontal Strainless steel pipe and base/cover plate with Strainless Steel GRADE 304 containing 7.5% nickle (Interior Grade) Brushed/Mat finish, complete as per direction of the Engineer-in-charge. Weight of Strainless Steel railing per metre 6.5 Kg (approx).

Labour for boring through any typeof soil for sinking tube well of required dia with top enlargement by rig boring system (either by reserve circulation or by direct rotary method) including hirechrges and labour for rig machine , tools and plants , staging, force pumping set and making arrangement for water required for boring etc. complete and lowering of pipes , strainer, blind pipes etc. complete. For depth upto 250 mtr. for 150 mm. dia tube well with top enlargement 250 mm. dia. upto 50 metre. (i) First 50 mtr.

(ii) Next 50 mtr.

(iii) Next 50 mtr .

(iv) Rest 100 mtr.

Supplying of PVC pipe & fittings ( medium duty ) conforming to ASTMD- 1785 & threaded to match with G.I pipe as per IS 1239 (Part -I). (A) PVC pipes. a) 200 mm dia.

(B) Long Bend (90 degree) a) 32 mm dia.

Washing and developing tube well with air compressor pump and engine for 8 (eight) hours continuous pumping per day with necessary arrangements for testing the yield in gallons per hour with 'V' notch including hire and labour charges for all tools and plants and scaffolding as required.

Supply & installation of submersible pump (crompton) with 1.5 H.P.motor.with following control box. Three phase (Steel casing) Containing starter, volt meter, Amp. Meter single phase preventer etc. and fittings fixing complete as per direction of the E.I.C.

Supplying, fitting & fixing 4.0 sqm 3 core alluminium armoured cable as per direction of EIC.

Supplying, fitting & fixing G.I cap at top. 200 mm dia.

Geophysical investigation of the acquifer by electrologging system with all tools and plants as necessary including supply of necessary report.

Labour for fitting and fixing U.P.V.C. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any floor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Engineer-in-charge. (Payment will be made on centre line measurement of the total pipeline including specials. Under Ground. 110 mm dia.

Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer. (d) 2000 litre capacity

Labour for hoisting plastic water storage tank.(ii) Above 1500 lire upto 5000 litre capacity.(a) Upto 1st story from G.L

Labour for hoisting plastic water storage tank.(ii) Above 1500 lire upto 5000 litre capacity.(a) Upto 2nd story from 1st story

Labour for hoisting plastic water storage tank.(ii) Above 1500 lire upto 5000 litre capacity.(a) Upto 3rd story from 2nd story

Labour for punching hole in plastic water storage tank upto 50 mm dia.

M.S. structural works in columns, beams etc. with simple rolledstructural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-in charge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. I) For structural members of specified sections weighing less than 22.5 Kg./m

Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading intotruck and cleaning the site in all respect as per direction of Engineer in charge.

Dismantling R.C. floor, roof, beams etc. including cutting rods and removing rubbish as directed within a lead of 75 m. including stacking of steel bars.(a) In ground floor including roof.

Planting of trees (Avenue plants) in 0.60m dia hole, 1m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure. This includes supply of labour, tools & plants including materials but excluding cost of tree.

Supplying and Planting of different plant / trees ( Supplying well grown plants bushy and healthy, minimum height as specified i.e. exposed height including all leads & lift, carriage, handling, manuring, applying presticide and fertilizer etc.viii) China palm of leaves 4-5 in earthen pots size 25cm.

xxvii) Areca Palm 4 - 5 suckers of height 120 cm to 135 cm in earthen pots of size 25 cm.

Brick edging 75 mm wide with picked jhama bricks, laid true to line and level including cutting necessary trench in soil or in hard metalled surface, laying the bricks and repacking the trench (on both side of the edging) with spoils and ramming the same thoroughly complete as per direction. (b) Brick-on-end edging (250 mm) depth.

Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be made on area of finished work). In roof. a|) with 0.5mm thick sheet

Galvanised iron sheets valley gutter with perimeter not less than 750 mm with 225 mm lap each way fitted and fixed withnecessary bolts, nuts, screws, etc.complete. Valley gutter made of 0.63 mm. thick sheets. (300mm End lapping)

Please Enable Macros to View BoQ information