SPECIAL REPAIR TO BLDG NO P 71 LIN CPLS AND BELOW ACCN FOR 200 ORs DB AT AF STN PHALODI

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ), removing serviceable tiles to store and rubbish off the premisses

Dismantling of stone slab and tiles of any description or thickness in floors, etc. laid bedded and pointed in any mortar.

M&L for coloured Glazed ceramic tiles in vertical surfaces of size 450mm x 300mm, 7 to 8mm thick over and including 10 mm thick rendering in CM 1:3 on fair faces of brick work or concrete surfaces , set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed.

M&L Non - skid joint free Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile,exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed by Engineer-in-charge.

M&L for 15mm thick screed bed or bedding layer of cement mortar 1:6, for laying floor finishes.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite

M&L for Vitrified Ceramic tiles 10 mm thick light shade (square/rectangular) polished area of each tiles not exc 0.36 sqm , over 15 mm thick screed bed of CM 1:6,in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed by Engineer-in-charge.

All as per Srl item No. 07 here in before but on vertical surfaces over 10mm rendering in CM 1:3 on fair faces of brick work or concrete surfaces and finishing the surfaces fair and even , complete all as specified and directed by Engineer - in - Charge.

M&L for Machine cut kota stone slab flooring 20-25 mm thick over cement screed base 20 mm thick in cement mortar 1:6, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

M&L for Machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over 15 mm thick rendering in cement mortar 1:4, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Demolition cement concrete (unreinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) complete all as specified and directed by Engineer - in - Charge.

M&L for 25 mm thick cement concrete flooring type B-0, 1:2:4 (using12.5 mm graded stone aggregate) surfaces of concrete topping to be finished even and fair (without using extra cement) all as specified and directed by Engr-in-charge.

M&L for 75 mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) fininshing the surfaces of concrete topping even and fair (without using extra cement)

S&F APP based polymeric membrane not less than 3 mm thick ,weighing notless than 3.5 kg/sqm ,reinforced with fiber glass (weighing notless than 150 gm/sqm ) and upper side of membrane thermally insulated with white mineral gravel finish ,informly embedded during manufacturing process shall only be used .it shall be used by torch application ,side overlap shall be75 mm and the ends shall be 100 mm and all over laps shall be sealed by torch application including applying a coat of cold applied bitumen primer confirming IS :3384 @0.4 kg/Sqm.

M&L for portland cement concrete type C2 1:3:6 (using 40mm graded coarse aggregate) delivered on bunker as in filling and mass concrete etc complete all as specified and directed by Engr-In-charge

Taking down shutters of any description exceeding 1 Sqm and not exceeding 2 sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down and refixing shutters exceeding 1.0 Sqm and not exceeding 2.0 Sqm each in same opening after resecuring or easing and adjusting complete all as specified & directed by Engineer-in- charge.

Taking down chowkhats or frames (without taking off shutters from the frames) not exceeding 1.5sqm each complete all as specified and directed by Engineer - in - Charge.

S&F fiber glass reinforced plastic(FRP)door frames three legged of cross section 90mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness ,the laminate door frame moulded with fire resistant grade unsaturated polyster resin and chopped mat .Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block of 2 nd class hard wood in all the three legs .The frame shall be covered with fiber glass from all sides.MS stay flat iron 25x 3mm shall be provided at the bottom to steady the frame complete all as specified by the manufacturer and directed by Engineer- in Charge.

Supply and fixing to existing door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer- in-charge.

S&F 100 mm Butt hinges type B-22 extruded aluminium alloy with galvanised mild steel hinge pin all as specified and directecd by Engr-in-charge.

Taking down chowkhats or frames (without taking off shutters from the frames) exceeding 1.5sqm but n.exc 4.0 sqm each complete all as specified and directed by Engineer - in - Charge.

S & F pressed steel door frames of size 105x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc.,complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No. 23 here in before but size 125 x 60mm complete all as specified and directed by Engineer - in - Charge.

S&F 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engineer - in - Charge.

M&L for 25 mm thick block board grade 2 quality interior grade decorative type with face veneers on both face fixed with screw to timber frame work as in kitchen cabinet and cupboards complete all as specified and directed by Engr-in-charge.

S & F 100mm size hasp and staple, safety type of aluminiun anodised complete all as specified and directed by Engineer - in - Charge.

S&F continous piano hinges mild steel bright finish or electro galvanised of 30 mm width of flaps (when open) all as specified and directed by Engr-in-charge.

S&F 35 mm thick II nd class hard wood glazed and skelton shutters open rebated and prepared to receive glass, gauze etc(without sash bars) edges of framing plain , chamfered or rounded fitted with cut and mitred beads for securing,glass etc size of members of shutters as specified in SSR part I ,section 8,clause 8.24 (a); supplied and fitted to chowkhats all as specified and directed by Engr-in-charge.

S&F 35 mm thick Factory made IInd class hard wood plain framed panelled shutters (Two Panels ) with lock rails and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces . the size of rail and stile as per IS :1003 (Part -i) Klin Seasoned and chemically pressure treated all as specified and directed by Engr-in-charge.

M&L for two coats of synthetic enamel on wooden surfaces of any description (ordinary tint) over one coat of pink primer over 10cm width or girth including preparation of new surface complete all as specified and directed by Engineer - in - Charge.

M&L one coat of synthetic enamel on wooden surfaces of any description (ordinary tint) old painted surfaces over 10cm width or girth including preparation of old surfaces complete all as specified and directed by Engineer - in - Charge.

M&L two coats of synthetic enamel paint (ordinary tint) on steel surfaces of any description over 10 cm width or girth, not otherwise described over a coat of red oxide, zinc chrome primer including preparation of new steel surface complete all as specified and directed.

M&L one coat of synthetic enamel paint (ordinary tint) on steel surfaces of any description over 10 cm width or girth, not otherwise described including preparation of old steel surfaces complete all as specified and directed .

S & F 150 mm size extruded aluminium alloy handles fabricated type, anodised and polished etc complete all as directed.

S&F 150mm size aluminium anodised barrel tower bolt of extruded section all as specified and directed by Engineer - in - Charge.

S&F 300mm aluminium alloy anodised sliding door bolt with hasp,staple and fixed clips of sheet,cast or extruded section and fixed bolts and sliding bolts of extruded section or cast aluminium alloy etc complete all as directed.

S&F in repairs mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete

S&F floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor overall lenth of cover plate 150mm etc complete all as directed by Engr-In- Charge

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average wirth of aperture 1.40mm and fixed with stainless steel wire staple etc complete all as directed by Engr-In- Charge

Taking down chowkhat or frame n exc 1.5 Sqm all as specified and directed.

S&F anodised Aluminium frame for doors, window, ventilators with one or more rebates including joining cleat for fixing etc complete with powder coating on Aluminium minium thickness of powder coating 50 micron as per the specification the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawl plug and screw or with fixing clip or with expansion hold plate fasteners . Aluminium section shell be smooth, rust free, straight mitred and jointed mechanically where ever required all complete as per the direction .

S&F Anodised aluminium door shutter aluminium section weighing 0.55 Kg/m incl necessary joining cleat, glazing clip,ruber neoprene packing handle 2NO in each door hing anodised aluminum snap beading screws etc complete all as specified'

S&F anodised aluminium window and ventilator shutter,fixed type without sashbars,aluminium section weighing 0.55kg/m including necessary joining claets,glazing clips,rubber packing,anodised aluminium snap beading screws etc complete all as directed by Engr-In- Charge

S&F 5.5 mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified and directed .

S&F 5.5 mm thick sheet glass ordinary quality and glazing with oil putty in square exceeding 0.5 sqm in each pane complete all as specified and directed .

S&F 6 mm thick bakelite sheet coloured,preliminated both side with colour choice laminations for fixing in doors partitions etc., confirming to relevant IS complete all as specified and directed.

S & F framed work such as grills, grating, etc., with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe 290 – Gde – 165 complete all as specified and directed.

M&L Cement concrete 1:2:4 type B–0(12.5 mm graded stone aggregate) filling of pressed steel frame and hold fast blocks etc complete all as specified and directed.

Hacking out old broken glass exc 1.5 sqm (any thickness, size, quality or description) from metal frames, including punching or drilling out old glazing pins / spring clips and glazed with oil putty and providing and fixing new ones complete all as specified and directed by Engineer - in - Charge.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified and directed by Engineer - in - Charge.

S & F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperature 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-charge.

S&F in repairs 150 mm Aluminium anodised barrel tower bolts of extruded section complete all as specified and directed

S & F in repairs aluminium alloy, anodized, sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast – aluminium alloy and fixed complete all as specified and directed by Engineer - in - Charge.

S & F in repairs aluminium alloy, anodized, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast – aluminium alloy and fixed complete all as specified and directed by Engineer - in - Charge.

S&F in repairs 150mm Extruded aluminium alloy handles fabricated type anodised complete all as specified and directed.

Taking down cement plaster or cement lime plaster on brick,stone or PCC walls etc. including raking out joints hacking for key scrubbing down with water etc all as directed .

M&L for Rendering 5 mm thick in CM (1:4) over 10 mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces finished even & smooth (without using extra cement) second layer mixed with WPC/water proofing chemical as per manufacturer's instruction.

M&L rendering 10 mm thick on stone masonry surfaces or surface but other than fair face of brickwork in CM 1:6 finished even and smooth (without using extra cement).

M&L 5mm thick, rendering in cement mortar 1:3 to ceiling surfaces finished even and smooth without using extra cement complete.

M&L three coats of white wash to undecorated ceiling surfaces including preparation of new surfaces complete all as specified and directed .

M & L one coat of white wash to old decorated plastered surfaces of ceilling including preparation of surfaces complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper of approved shade/tint over a coat of chalk whiting as primer on walls all as specified & directed by Engineer-in-Charge

M & L for complete removal of existing treatment on walls and applying two coats of oil bound distemper white or tinted over a coat of chalk whiting primer over 3mm thick wall care putty on wall.

M&L for preparing old decorated plastered or unplastered surfaces of walls and applying one coat of white wash on walls complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of walls and applying two coat of whitewash on walls complete all as specified and directed .

M&Lfor new plastered surfaces of walls and applying two coats of cement base paint of approved shade over alkali resistant primer complete all as specified and directed by Engineer-in-Charge

M&L for old decorated plastered surfaces of walls and applying one coat of cement base paint complete all as specified and directed by Engr-in-Charge.

S & F steel ventilators with top hung shutter including hinges ,steel peg stay including painting with one shop coat of zinc chromate primer ,complete all as specified and directed by Engineer - in - Charge.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay complete with glazing bars,dovetailed or welded including painting with one shop coat of zinc chromate primer, all as specified and directed by Engineer -in- Charge.

Taking up or down 20mm bore steel water tubing galvanised and connections including cleaning for re-fixing or removal to store complete all as specified and directed by Engineer - in - Charge.

S&F(outer dia of pipe 20 mm) 3-layer PP-R Polypropylene random copolymer)concealed pipes SDR 7.4 (PN16) UVstabilized and antimicrobial fusion welded having thermal stability forhot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc.

Taking up or down 15 mm bore steel water tubing galvanised and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer - in - Charge.

S&F(outer dia of pipe 16 mm) 3-layer PP-R Polypropylene random copolymer)concealed pipes SDR 7.4 (PN16) UVstabilized and antimicrobial fusion welded having thermal stability forhot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc.

S & F in repair bib taps 15mm bore dia of pipe, cast copper alloy chromium plated, fancy type with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge.

S&F in repairs, bib taps 15mm bore dia of pipe cast copper alloy, with crutch or butterfly handles, screwed down, screwed for iron pipe or brass ferrule complete all as specified and directed by Engineer - in - Charge.

S&F in repairs 15mm bore dia of pipe Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe complete all as specified and directed by Engineer - in - Charge.

S&F in repairs 20mm bore dia of pipe Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe complete all as specified and directed by Engineer - in - Charge.

S&F in repair 15 mm bore dia of pipe fancy type chromium plated concealed type stop valves, cast copper aloy with crutch or butterfly handles screwed down high pressure, screwed both ends for iron pipe or for unions

Dismantling water tanks capacity exceeding 250 and n exc 500 litres complete all as specified and directed.

Disconnecting existing water tanks of capacity exceeding 250 amd n.exceeding 500 litrs, setting aside (or lowering if required) for reoairs, cleaning,etc. and hoisting if required reconnecting and refixing in portion including cleaning and removing all scale and dirt,etc. from tanks and from mouths of circulating pipes etc.

S&F rotational moulded polyethylene water storage tank 500 ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank 1000 ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed.

S&F 25mm bore ball brass valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repairs, 15 mm bore Brass CP basin mixer for mixing hot and cold water screwed down for iron pipe and fied complete all as specified and directed by Engineer - in - Charge.

Demolition of RCC slabs, chajjas and similar suspended work complete all as specified and directed by Engineer - in - Charge.

M & L RCC 1:2:4 nominal mix (20 mm graded stone aggregate) Type B1 for chajjas complete all as specified and directed by Engineer - in - Charge.

Formwork to chullah hoods, chajjas, troughs and similar items including rough finished surfaces of flat concrete edges complete all as specified and directed by Engineer - in - Charge.

M & L mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed by Engineer - in - Charge.

All as per item above but 5 mm dia and over up to and including 10 mm dia but in stirrups, spacers and binder etc complete all as specified and directed by Engineer - in - Charge.

Dismantling cast iron work of any description complete all as specified and directed by Engineer - in - Charge.

S&F 100mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed by Engineer - in - Charge.

S&F 75mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed by Engineer - in - Charge.

S&F 100mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls complete all as specified and directed by Engineer - in - Charge.

S&F 75mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears, with cement joints,fixed to walls complete all as specified and directed by Engineer - in - Charge.

S&F 100mm bore cast iron bends sand cast (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed by Engineer - in - Charge.

S&F 75mm bore cast iron bends sand cast (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed by Engineer - in - Charge.

Extra over 100 cast iron pipes and fittings if lead joint is provided in lieu of cement joint

Extra over75 mm cast iron pipes and fittings if lead joint is provided in lieu of cement joint

M&L for CI floor trap 75 mm with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) all as specified and directed by Engr-in-charge.

M&L for CI floor trap 100 mm with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) all as specified and directed by Engr-in-charge.

S&F in repairs Grating doom 100mm dia PTMT(minimum weight 25gms) complete all as specified and directed by Engineer - in - Charge.

Taking down eaves gutters and rain water pipes (any size or pattern) including all fittings, heads, shoes, bends, swan – necks, etc. including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fitting and accessories) of any description complete all as specified and directed by Engineer - in - Charge.

M&L bands, straps,supports or stays for rainwater ventilating pipes including bolts conforming to Fe 290Gde-E-165 all as specified and directed .

Cutting holes in brick walls for inserting hold fast etc built in C:M n exc half brick wall and making good in cement conc 1:2:4 type B-1 complete all as specified and directed by Engr-in-charge.

S&F 110mm bore PVC (SWR) rain water pipe single socketed in any length with rubber ring joints, jointed with solvent joint fixed to wall complete all as specified and directed by Engineer - in - Charge.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed by Engineer - in - Charge.

Dismantling of brick work or block masonry built in cement mortar of any description complete all as specified and directed by Engineer - in - Charge.

M&L Precast cement concrete type C1 1:3:6 (20mm graded stone) block masonry with solid blocks exc. 10 cm in width and setting in cement mortar1:6 complete

S & F in repair brass chromium plated tubular towel rail 20mm dia “D” type 60 cm long between flanges including brackets complete all as specified and directed by Engineer - in - Charge.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engineer - in - Charge.

S&F water closet vitreous china squatting pan "Orissa pattern" size 580mmx440mm white with integral foot rests (Excl flushing cistern and flush pipe) complete all as specified including CI 'P' trap all as specified and directed by Engr-in-charge.

S&F in repairs vitreous china bowl urinal flat back size of 465x355x265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flushing pipe and waste pipe) complete all as specified and directed by Engineer - in - Charge.

S&F in repair vitreous china wash down water closet pan (Pedstal pattern), white excluding fixing bolts, flushing cistern and flush pipe, including plastic water coset seat, black cosed pattern with flat bottom, and cover and mild steel chromimum plated hinging device.

S & F in repair PVC valveless syphonic action type 10 ltr capacity flushing cistern low level with inlet ball valve, float and handle including brackets with 32mm dia flush pipe of polyethylene of low or high density including 450 mm pvc connection complete all as specified and directed by Engineer-in-charge.

S&F in repair stainless steel curtain rod 25 mm dia (minimum weight 0.36 Kg per RM) with brackets, fancy knobs and stand etc complete all as specified and directed by Engr-in-charge.

M & L for 50 mm thick cement concrete type C – 1 (1:3:6) using 20mm graded stone aggregate as in plinth protection finished even and smooth etc complete all as specified and directed by Engineer - in - Charge.

S&F IInd class hard wood small fittings such as brackets of any type latch and hinge blades shaped door and window stops and the like including all necessary labour article n.exc 200cu.cm each all as specified and directed by Engr-in-charge.

Demolition of cement concrete exc 15cm thickness in sunken portion but above ground floors all as specified and directed by Engr-in-charge.

M&L for water proofing treatment to RCC sunken slab as specified below asd as directed by engr-in-charge:- (a) 15mm plaster in CM 1:3 with WPC on raised vertical surface. (B) Cleaning the surface with wire brush/coir brush, removing loose material like dust particles ,dirt etc. (c) Creating fillet covering of 50x50 mm with polymer modified mortar on the junction of slab and walls (d) Apply first coat of two component modified polymer coating on the horizontal and vertical surfaces. (e) Provision of glass fibre mesh of 2x2 mm immidiately on above coating (f) Apply second coat of two component modified polymer coating after 72 hours (g) Laying concrete 1:4:8 over the coating as per requirement (h) Joining the sanitary pipe with non shrink cementatiuos grout (k) Complete the treatment to be carried out by authorised applicator of waterproofing manufacturer Make :- Dr. Fixit/Fosroc/BASF/STP NOTE : (i) The Treatment shall be carried out as per the manufacturers industreis and as directed by eng-in-charge. (ii) The plan area of floor shall be consider for payment. (iii) WPC shall be measured and paid saperately.

Supply only integral Water proofing compound

M&L for cement concrete type E2 1:5:10 (40mm graded stone aggregate) as in foundations filling and mass concrete etc complete all as specified and directed by Engr-in-charge

M&L for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc complete all as specified & directed.

M&L for green marble work 18 to 20mm thick (table rubbed and polished)in steps,jambs,pillars,window cills,cooking platforms and like in cement mortar (1:4)including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete.

Demolition and breaking up 200mm internal dia drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar all as directed

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required (for 225mm internal dia of pipe) bore

M&L for 200 mm bore Reinforced concrete pipes, class NP2, laid and jointed with collars complete with collars in cm(1:1) with spun yarn & tested .

M&L for Sand cushioning all as specified and directed .

M&L for polyster triangular/ non circular synthetic fiber mixed @ 1.00 kg per cum of cement mortar complete all as specified and directed by Engineer -in-Charge

Taking down carefully existing copper/aluminium point wiring (light/fan/bell/sockets) Flame proof point wiring complete with all accessories such as switches sockets ceiling rose, wall bracket etc and removing dismantled material and making good disturbed surface of walls/floors etc matching with existing surface etc complete all as specified and directed by Engineer-in-Charge.

M&L point wiring for one light point /fan point/bell point controlled by one switch with 1.5 Sqmm (nominal area) PVC insulated, unsheathed multi strand copper conductor cable FR-LS in existing concealed PVC conduit including new steel terminal sunken boxes suitable for modular switch/socket flush to surface (including modular frame and cover plate) for one light point, fan point , controlled by one switch on the same board with other switch or independent including PVC insulated unsheathed 1.5 Sqmm multi stranded copper conductor cable FR-LS connected to common earth dolly complete all as specified and directed by Engineer-in-charge. (Note :- Switches, sockets etc shall be measured and paid for separately under appropriate items of Sch

All as per item No 132 but for one socket point outlet 3 Pin, 5 Amp 230 Volt on same board.

All as per item No 132 but for one socket point outlet 3 Pin, 5 Amp 230 Volt on independent board.

All as per srl item No. 132 (here-in-before) but for 3 pin 15 Amp socket out let by using 2.5 Sqmm PVC insulated unsheathed copper conductor cable FR-LS multi strand on independent board including provn of 2.5 Sqmm unsheathed, multi stranded copper conductor cable FR-LSH continues as earth wire connected to earth dolly etc complete all as specified and directed by Engineer-in-Charge.

M & L for point wiring for one light / fan point controlled by one switch with 1.5 Sqmm (nominal area) PVC insulated, unsheathed multi strand copper conductor cable FR-LS in concealed PVC conduit 20 mm dia heavy duty ISI marked, steel terminal sunken boxes and 3 mm thick phenolic laminated sheet top cover for sunken boxes flush to surface for one light point/fan point, controlled by one switch on the same board with other switch or independent including PVC insulated unsheathed 1.5 Sqmm copper conductor cable FR-LSH connected to common earth dolly complete all as specified and directed by Engineer-in-charge.(Note :- Chases cutting & making good ,Switches, sockets etc shall be measured and paid for separately under appropriate items of Sch ' ).

All as per item No 136 but for socket 5 Pin, 5 Amp 230 Volt on same board.

All as per item No 136 but for one socket point outlet 3 Pin, 5 Amp 230 Volt on independent board.

All as per srl item No. 136 (here-in-before) but for 15 Amp socket out let by using 2.5 Sqmm PVC insulated unsheathed copper conductor cable FR-LS multi strand on independent board including provn of 2.5 Sqmm unsheathed, multi stranded copper conductor cable FR-LS continues as earth wire connected to earth dolly etc complete all as specified and directed by Engineer-in-Charge.

M&L Cutting chases, pinning in on brick walls. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc., and making good, cutting not exc 10 cm girth

Supply and Fixing modular switch 1way, 6 Amp , 1 module 240 Volt, AC complete all as specified and directed

S&F modular socket 6A- 2/3 pin combined 2 module, 230 volts AC complete all as specified.

S&F Modular Switch socket combination 6A, 3 pin, flush type universal 230 volts AC complete all as specified.

S&F modular Switch socket combination 16A 6 pin, 3 module 230 volts AC complete all as specified.

S&F modular Ceiling fan regulator step type 120 watt- 2 module, 230V suitable for 1200/1400 mm ceiling fan etc complete all as specified

S&F ceiling rose surface bakelite 65mm x 50mm, 2 to 3 terminals with back plate etc complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing LED batton fitting 1 x 20 Watt, 6000K, 4' complete fitting connection with 2 core flexible cable 23/0.00076 from ceiling rose to tube fitting connection etc complete all as specified

Supply and Fixing LED batton fitting 1 x10 Watt, 2' complete fitting connection with 2 core flexible cable 23/0.00076 from ceiling rose to tube fitting connection etc complete all as specified

S&F LED light fitting, 1X35 watt, complete with tuff net glass protection IP:66, fixed to walls with GI bracket made out of suitable size of light grade pipe 32 mm dia tubing upto 1.2 mtr length bent to shape with 02 sets of MS clamps made out of 25x3 mm MS flat iron with suitable bolt and nuts and testing etc complete all as specified

Taking down of Sub main wiring with two single core cable PVC insulated unsheathed of copper multi strandard conductor cable of any size

S&F Sub main wiring with two single core cable PVC insulated unsheathed of copper multi strandard conductor cable of size 4 sqmm, 1100 votls grade drawing through concealed PVC conduit of edequate size medium duty and including PVC insulated 2.5 sqmm unsheathed multistranded FR-LSH copper conductor cable for earth continuity and connected to common earth dolly complete all as specified

S&F Sub main wiring with two single core cable PVC insulated unsheathed of copper multi strandard conductor cable of size 6 sqmm, 1100 votls grade drawing through concealed PVC conduit of edequate medium duty and including PVC insulated 4 sqmm unsheathed multistranded FR-LSH copper conductor cable for earth continuity and connected to common earth dolly complete all as specified

S&F Sub main wiring with four single core cable PVC insulated unsheathed of copper multi strandard conductor cable of size 16 sqmm, 1100 votls grade drawing through concealed PVC conduit of edequate size of medium duty and including PVC insulated 6 sqmm unsheathed multistranded FR-LSH copper conductor cable for earth continuity and connected to common earth dolly complete all as specified

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 240 volt 20Amps

Supply and fixing VTPN DB double door sheet metal enclosure made out of CRCA mild steel sheet concealed surface mounting VTPN, 12 way, 230 Volt, with 200 Amp rated bus bar suitable for fixing MCBs, isolators etc including MCCB of rating 250 Amp,25 kA,4 pole,complete all as specified and directed.

Supply and fixing double door sheet metal enclosure made out of CRCA mild steel sheet concealed surface mounting SPN, 8 way,240Volt, suitable for fixing MCBs, isolators etc including taking down old complete all as specified and directed.

S&F Isolator TPN 100 Amps 415V etc complete all as specified

S&F Isolator SPN 63 Amps 230V etc complete all as specified

S&F Isolator SPN 40 Amps 230V etc complete all as specified

S&F MCB 6 Amp to 32 Amp SP capacities 'C' series 10KA rupturing capacaity complete all as specified and directed.

Taking down serviceable/unserviceable ceiling fans 1200mm/1400 mm sweep 230 V, AC, single phase from ceiling, dismantling the ceiling fan and taking out complete rewinding (if unserviceable) the same with super enameled copper winding wire of existing gauge & size including throughly cleaning all the components of fan, oiling varnishing the fan with and including replacement of rusted/unserviceable nuts, bolts, split pin, rubber reel, flexible twin core copper cable of size 23/.00076 approximate one metre long for each fan, machine screws and painting the fans etc, and refixing the repaired fan to existing place complete all as specified

Taking down serviceable/unserviceable exhaust fan /flame proof exhaustfan of any sweep 230 V, AC, single phase , dismantling the Exhaust fan and taking out complete rewinding (if unserviceable) the same with super enameled copper winding wire of existing gauge & size including throughly cleaning all the components of fan, oiling varnishing the fan with and including replacement of rusted/unserviceable nuts, bolts, split pin, rubber reel, flexible twin core copper cable of size 23/.00076 approximate one metre long for each fan, machine screws and painting the fans etc, and refixing the repaired fan to respective bathrooms complete all as specified

M & L for earthing with galvanized steel plate electrode 600 x 600 mm x 6 mm size directly burred in ground vertically earth pit not less than 2.25 meter deep below normal ground level with top edge of the earth plate not less than 1.5 m below normal ground level surrounded with coal dust and common salt filling in alternative layers of 15 cm thick each connected to and including GI earth wire 4 mm dia by means of GI nuts, bolts, check nuts & washers etc connecting to earthing test point, main switch board and including 15 mm dia GI pipe light grade for protection of earth lead from earth plate upto 5 mtr and 20 mm dia GI pipe medium grade connected with funnel having wire mess for watering purpose including necessary excavation and earth work, PCC (1:2:4) type B-1 (using stone aggregates) for earthing pit, 10mm thick cast iron cover with angle iron frame all as specified and shown in electrical plate No 3 of SSR Part-I and testing on completion.

KRISHNA CONSTRUCTION COMPANY

Aggarwal brothers and company

M/S SOLANKI GENERAL SUPPLIERS

M/S HARIOM CONSTRUCTION COMPANY