Construction of Govt Sen Sec School Bharari in Tehsil Thunag Distt Mandi SH C/o Building portion site development WSSI Septic tank soak pit harvesting system

Amount

Excavation in foundation, trenches etc. in earth work in all kinds of soil such as pick work, Jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/dewatering upto any lift, stacking the excavated soil upto any lead from the edge of excavation and then returning the stacked soil in layer when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth to the disposal point including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Earth work in excavation for structure as per drawing and technical specification clause 305.1 i/c setting out construction of shoring and bracing removal of stumps and other deletarious material and disposal up to any lead dressing of sides and bottom and back filling in trenches with excavated suitable material ordinary soil including carriage of material with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing form work with steel plates 3.15mm(Three point fifteen millimeter) thick welded with angle iron in frame 30x30x5mm(Thirty millimeter into thirty millimeter into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and bellies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in situ-reinforced concrete and pain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge. Vertical surface such as walls(any thickness) and the like including attached pilasters, buttersses plinth and string courses and the like

Foundation, footing basis of columns etc. and mass concrete .

Flat surfaces such as soffits of suspended floors, roofs, landings and the like Floors etc upto any thickness.

Beams, cantilever, girders and lintels sides and soffits of beams, beam haunching, cantilevers, bressumers and lintels in any depth in all height from floor..

Columns, pillars, Posts and struts, Square, rectangular or polygonal in plan

Stair cases with sloping or stepped soffits excluding landing

Edges of slabs and breaks in floors and walls in any width.

Providing and laying cement concrete 1:6:12 (1 cement:6 sand : 12 graded stone aggregate 40 mm(fourty millimetre) nominal size and curing complete excluding cost of centring and shuttering in Foundation and plinth including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge.

Providing and laying concrete (C.C 1:6:12) (one cement : six sand twelve graded stone aggregated) 40 mm ( forty mm) nominal sizse for plain/reinforced concrete in open foundation complete as per drawing and technical specification Clause 802,803,1202 and 1203 with in all leads and lilfts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and laying cement concrete 1:5:10 (one cement : five sand : ten graded stone aggregate 40mm (forty millimetre) nominal size) including curing and cost of form work for plain/reinforced concrete in retaining walls, bresat walls, as per drawing and HPPWD technical specifications clause 803,802,1202 and 1203 complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying cement concrete 1:4:8 ( one cement: four sand: eight graded/ crushed stone aggregate 40mm (Forty millimetre ) nominal size) mechanically mixed and vibrated and curing complete excluding the cost of form work in foundation and plinth including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Random Rubble Stone masonry in cement mortar 1:6 (one cement : six sand) for substructure complete as per drawing & technical specification Clauses 702,704,1202 and 1203 including curing complete and carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing weep hole in brick masonry/ stone masonry / plain reinforced concrete abutment, wing wall, return wall with 100mm dia.(one hundred millimetre diametre) PVC pipe extending through the full width of the structures with slope of 1V:20H (one vertical isto twenty horizontal) towards drawing face complete as per drawing and technical specifications clauses 614,709,1204.3.7 including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Back filling behind abutment wing wall and retainling wall complete as per drawing & technical specification clause 1204.3.8 and including carriage of material with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Stone filling for filter matrialin filter chamber complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying cement concrete work 1:2:4 (1 Cement:2 Sand:4 graded curshed stone aggregate 20 mm (twenty millimetre) nominal size) and machanically mixed vibreted curing complete excluding cost of form work and reinforcement for reinforced concrete work in including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge Suspended Floor roofs, landing and shelves and their support balconies, beams, girders, bressumers and cantilever up to all floor level.

Walls (any thickness but not less than 0.10 metre thickness) including attached pilastersnbuttersses, plinth and string courses etc up to all floor level.

Providing and laying cement concrete 1:1.5:3 (1cement :1.5 sand :3 graded stone aggregate 20mm (twenty millimetre) nominal size mechanically mixed vibrated and curing complete excluding cost of form work and reinforcement for concrete work in including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. Foundation footings bases of columns and the like and mass concrete.

Suspended floors roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers upto floor any level.

Column, pillars, posts and struts up to all floor level

Stair cases (except spiral stair case) excluding landing but including preparing of the surface and finishing of nosing up to all floor level

Providing and laying reinforced cement concrete 1:2:4 (one cement : two Sand :four graded stone aggregate 20mm (twenty millimetre) nominal size mechanically mixed and vibrated to give an smooth and even surface including centring and shuttering etc upto all level but excluding cost of reinforcement in String courses, copings, bed plates, anchor blocks, plain windows sills and the like including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire up to any level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (1 cement :6 sand : 12 graded stone aggregate 20mm (twenty millimetre) nominal size at plinth level in Cement Mortar 1:6(1 cement:6 sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing in RCC work smooth finishing of the exposed surface with cement mortar 1:3 (1 cement : 3 sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Brick work using common burnt clay building bricks in superstructure above plinth level up to any floor level in Cement Mortar 1:6 (1 Cement : 6 Sand) Second Class Bricks including curing complete and carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Half brick masonry in common burnt clay building bricks in cement mortar 1:3 (one Cement :Three Sand) (2nd Class Brick)in super structure above plinth level upto all floor level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing woodwork in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position 2nd class deodar wood including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 40 mm (fourty millimetre) thick 1st class Deodar wood panelled glazed or panelled and glazed shutters for doors windows and clerestory windows including black enamelled iron butt hinges with necessary screws including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing fully double glazed (double glass) shutters for doors windows and clerestory windows Including black enamelled iron butt hinges with necessary screws 40 mm (fourty millimetre) thick 2nd class deodar wood including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing double glazing (double glass) fixed in door, window, ventilator shutters and partition etc with wooden corner or wooden bed in teak wood. complete glazing with glass panes of 4mm (four millimetre) thickness (weight not less than 10.00 kg/sqm. (ten kilogram per square metre) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 2nd class deodar wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm (zero point five six millimetre) for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 12mm (twelve millimetre) thick 150mm (one hundred fifty millimetre) wide pelmet with 25 mm (twenty five millimetre) diametre wooden curtain rods and brackets including fixing 25x3mm (twenty five into three millimetre) M.S. flat at 10 cm (ten centimetre) Long and plugs etc. complete 2nd class indian teak wood including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing brass curtain rail with rollers stop ends and brackets in pelmets instead of wooden curtain rod 25 mm (twenty five millimetre) dia and brackets of first class deodar wood (actuallenght) of rails of be measured including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing M.S. plain grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing 40x3 mm (fourty into three millimetre) flat iron hold fast 40cm (fourty centimetre) Long including fixing to frame with 10mm (ten millimetre) diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm (thirty into ten into fifteen centimetre)1:3:6 ( 1 cement : 3 sand: 6 graded stone aggregate 20mm (twenty millimetre) nominal size including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 2nd class indian teak wood 75 mm x 60mm (seventy five millimetre into sixty millimetre) rounded hand rails in straight length complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing oxidized M.S. sliding door bolts with nuts and screwsm etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 300x16mm (three hundred into sixteen millimetre)

250x16mm (two hundred fifty into sixteen millimetre)

Providing and fixing oxidised M.S. tower bolts (barrel type) with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 250x10mm (Two hundred fifty into ten millimeter)

150x10mm (One hundred fifty into ten millimeter)

Providing and fixing oxidized M.S. handles with the necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 125 mm (One hundred twenty five millimeter)

100 mm (One hundred millimeter)

Providing and fixing 100mm (One hundred millimeter) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 150 mm (one hundred fifty millimetre) bright finished hard drawn hooks and eyes including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 115mm (one hundred fifteen millimeter) oxidized M.S hasps and stapples (safety type) with necessary screws etc complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 150 mm (one hundred fifty millimetre) M.S. single acting spring hinges bright finished with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 19mm (nineteen millimetre) thick Commercial Board water proof shutters for up boards including fixing with nickel plated piano hinges with screws etc complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 19mm (nineteen millimetre) thick water proof commercial board in shelves/box for cup board with butt joints & fixing with nails & screws etc complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing wall paneling of 12 mm (twelve millimeter) thick pre laminated particle board (one side) of approved brand of soft wood 4x4 cm frames @60 cm center to center on both side fixing with rawl on wooden plugs and screws and showing 8 mm wide in elevation and finished teak wood beading outlay 25x12 mm deep groves of required pattern of 25x12mm(twenty five millimeter x twelve millimeter) /Cornish out to 75x60mm(seventy millimeter x sixty millimeter) of different pattern in top middle and corner joints including polishing and painting groves complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying spartic ceremic tiles 5.5mm (five point five millimetre) thick in flooring 300 x300mm (three hundred into three hundred millimetre) size treads of steps laid on a bed of 12mm (twelve millimetre) thick cement mortar 1:3(1cement: 3 sand) finished with flush pointing in white cement including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

40 mm (fourty millimetre) thick Kota stone slab flooring 20 mm (twenty millimetre) (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Kota stone slab 25 mm (twenty five millimetre) thick in risers of steps,skirting dado and pillars laid on 12 mm (twelve millimetre) (average) thick cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 10mm (ten millimetre) thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 600x 600mmx10mm (six hundred millimetre into six hundred millimetre into ten millimetre) manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm (twelve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

25 mm (twenty five millimetre) thick wooden flooring laid over R.C.C/C.C. slab (to be paid separately) (thinly coated with thin layer of hot bitumen blown type) @ 2.45 kg per sq m (two point four five kilogram per square metre) including fixing of wooden planks in position over wooden plugs fixed in c.c./R.c.c. floor including planning and levelling complete 2nd class deodar wood including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

40 mm (fourty millimetre) Cement concrete flooring 1:2:4 (1 cement : 2 sand:4 graded stone aggregate 20 mm (twenty millimetre) nominal size laid in one layer finished with a floating coat of neat Cement including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 0.60mm (Zero point six zero milimetre) thick preprinterd steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) micons primer coating to back coast of polyester of 5 microns over 5 microns primer coating including fixing with screws, prepainted iron J or L hooks, bolts and nuts 6mm(six milimetre) dia with prepainted limpet and rubber washer complete with all accessories as required as per specifications including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing ridges or hips 60 cm (Sixty centimeter) overall with 0.60 mm (Zero point sixty millimeter) thick preprinted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat or regular modified polyester organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with preprinted iron J or L hooks, bolts & nuts 6mm(Six millimeter) dia and preprinted G.I. limpet and bitumen washers complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing valley 60 cm (Sixty centimeter) overall 0.60mm (Zero point sixty millimeter) thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 (five) microns over 5 (five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimeter) dia with prepainted G.I. limpet and bitumen washers complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm (one point six six millimetre to two millimetre) thick in eaves board/facia/soffits/ ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 15 cm (fifteen centi metre) wide 45 cm (fourty five centimetre) overall semicircular plain G.I. sheetgutter with iron brackets 40x3mm (fourty into three millimetre) size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design 0.63mm (zero point six three millimetre) thick sheet including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing on wall face 100mm (One hundred milimetre) dia PVC(D-Plast) rain water pipes of working pressure not less than 4.5 Kg/sqm(Four point five kilogram per square metre) including filing the joint with approved adhersive complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying in trenches 100 mm (one hundred mm) 4 kg/T/cm2 working pressure unpalvarised pVC pipe (conforming to IS complete with Fitting) earth trenches to be measured and paid for seperately without diametre including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing on wall face (D-Plast) accessories for rain water pipes including filling the joint with approved adhesive complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. PVC Plain Bend 100mm(One hundred milimetre) dia.

Shoe 100mm (One hundred milimetre) dia.

Steel work welded in built up sections,trusses and framed work,including cutting, hoisting, fixing in position and applying a priming coat of red lead paint including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. In beams joists channels, angles, tee, flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like.

In gratings framed guard bars, ladders, railling, brackets and similar works.

In trusses and trussed purlins in buildings.

Providing and fixing angle iron cupboard frames manufactured from M.S.Angle iron section 25X25X5mm (twenty five into twenty five into five millimetre) thickness including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 25X25 mm (twenty five into twenty five millimetre) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm (two point five millimetre) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing calcium silicate tiles ceiling of approved quality with butt jointing and nail (Frame work and cover fillets to be paid for separately). False ceiling in combination with prepainted steel section including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

6mm (six millimetre) Cement plaster to ceiling In Cement Mortar 1:4(1 Cement : 4 Sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

15mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/concrete/stone wall for interior plastering upto floor all level including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:6 sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering up to all floor level includingarises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:six sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering up to all floor level includingarises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:5 (one cement : five sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease,dirt and other forein matter sand papering and knotting ready mixed paint with wood priming pink including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Painting two coats(excluding priming coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping With enamel paint other than white including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Painting two costs (excluding priming coat on new steel and other metal surfaces with enamel paint brushin to give an even shade including cleaning the surface of all dirt,dust and other foregin matters Enamel paint other than white including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Polishing two coats with french polish on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt,dust,and sand papered smooth and including a coat of wood filler including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smoothPriming coat with distemper primer including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equivalent on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing plinth protection 50mm (fifty millimetre) thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm (twenty millimetre)nominal size including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing under layer for plinth protection of 75mm (seventy five millimetre) thick (unconsolidated) bed dry brick/stone aggregated 40mm (fourty millimetre) nominal size with rammed and consolidated and grouted with fine sand including preparation of ground including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Construction coursed, rubble, hammer dressed "U" shape open surface drain with side wall 15X22cm (fifteen into twenty two) in cement mortor 1:6 (one cement: six sand) and in side plstring with cement plaster 1:3 (one cement : three sand ) including earth work and laying 10cm (Ten Centimetre) cement concrete 1:5:10 (one cement :five sand:ten graded stone aggregate 40mm (Forty millimetre) nominal size) and 7.5cm (seven point five centimetre) cement concrete 1:2:4(one cement :two sand ;four graded stone aggregate 20mm (Twenty millimetre) nominal size) and finishing with a floating coat of neat cement and curing complete as per standard design including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 75 mm (seventy five millimetre) nominal size. PVC clamps, ISI marked of approved design with steel screws and rawal plugs etc. Complete with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Suppliying cast iron cover without frame for manholes For frame of internal dimension 455mmx610mm (four hundred fifty five millimetre into six hundred ten millimetre) rectangular C.I. cover (light duty single seal pattern-1) the weight of cover to be not less than 23kg (twenty three kilogram) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing 20 mm (twenty millimetre) nominal bore to wall ceiling and floor galvanized mild steel tube (medium grade) tube fittings and clamps including making good the wall ceiling and floors with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing PVC water storage tank of ISI:12701 marked,G.I.inlet and outlet connection,15mm (fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level:-2000 (two thousand) litres capacity. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing plythelineo-aluminiumo-polythelene(PE-AL-PE) composite pressure pipe U.V.stabilized with carbon black confirming to IS-15450-2004 water supply including clamp at one meter spacing,cutting,fixing and making good the wall etc.but excluding the cost of fittings(internal work) pipesexposed on wall. (KITEC make) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 1620 (one thousand six hundred twenty) 20 mm (twenty millimetre) OD pipe

1216 (One thousand two hundred sixteen) 16mm (sixteen millimetre)O.D.Pipe.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors,couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. (KITEC make) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. Reducing tees 1620 (one thousand six hundred twenty) x all branches

Equal tees i)1216 (one thousand two hundred sixteen)

Female branch TEE i)1216x1216x15mm (one thousand two hundred sixteen into one thousand two hundred sixteen into fifteen millimetre) thread.

Female elbows i)1216x15mm (one thousand two hundred sixteen into fifteen millimetre) thread.

Female thread connector i) 1216x15mm (one thousand two hundred sixteen into fifteen millimetre) thread.

couplers i) 1216 (one thousand two hundred sixteen).

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc complete. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm (seventy five) nominal size.

110mm (one hundred ten millimetre) nominal size.

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete including fixing with approved adhesives etc. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 110mm (one hundred ten millimetre) nominal size

75 mm (seventy five) nominal size.

Providing and fixing PVC single equal branch plain, ISI marked including fixing with approved adhesives etc. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm (seventy five millimetre) dia

110 mm (one hundred ten millimetre) dia

Providing and fixing PVC collar, ISI marked including fixing with approved adhesives etc.with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm (seventy five millimetre) nominal size.

110mm (one hundred ten millimetre) nominal size.

Providing and fixing PVC plain bend, ISI marked including fixing with approved adhesives etc. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm (seventy five millimetre) nominal size.

110mm ( one hundred ten millimetre) nominal size.

Providing and fixing PVC clamps, ISI marked of approved design with steel screws and rawal plugs etc. Complete. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm (seventy five millimetre) nominal size.

110mm (one hundred ten millimetre) nominal size.

Providing and fixing PVC floor trap ISI marked of self cleansing design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. 110 mm x 75 mm (one hundred ten millimetre into seventy five millimetre) size. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing vitreous China wash down, water closet squatting pan (Indian type W.C pan) size 580mm (five hundred eighty millimetre) (Earth work, bed concrete, foot rest and trap to be measured and paid for separately). Orissa pattern (Cera) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing vitreous china water closet(European type w.c.pan) with integral 'p' or 's' trap including jointing the trap with soil pipe in cement mortar 1:1 (1cement:1sand)(seat and cover to be measured and paid for seprately):-(Cera) Anglo indian universal closet with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing PTMT coloured/white high density polyethylene/poly propylene 10 (ten) litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm (fifteen millimetre) nominal size PVC ball valve with polythene float,with push button, couplings for connections with inlet,outlet and overflow pipe, 40mm (forty millimetre) dia C.P.flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (over flow pipe to be measured and paid for seprately) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing plastic seat(solid/hollow type) and cover for wash down water closet with c.p. brass hinges and rubber buffers:-Solid type (a) white plastic seat and cover with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings extra for pair of hole for pillar tap instead of single hole (Jaquar or ESS-ESS) Flat Back 550mmx400mm (five hundred fifty millimetre into four hundred millimetre) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing vitreous china pedestal for wash basin complete recessed at the back for reception of pipes and fittings. (Jaquar or ESS-ESS) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing CP brass toilet paper holder including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge. (Jaquar or ESS-ESS) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing 32mm (thirty two millimetre) dia C.P Brass waste for wash basin or sink with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing 32mm (thirty two millimetre) dia MI union for wash basin or sink with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing vitreous China bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with choppe hemp (weste pipe to bemeasured and paid for separately Flat back type of size 430mm x 260 mm x 350mm (four hundred thirty millimetre into two hundred sixty millimetre into three hundred fifty millimetre) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing division plate for urinals 600mm x300mm (six hundred millimetre into three hundred millimetre) virterous china including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge. (Jaquar or ESS-ESS)

Providing and fixing 600mm x450mm (six hundred millimetre into four hundred fifty millimetre)beveled edge mirror of superior glass mounted on 6mm (six hundred millimetre) thick A.C sheet or ply wood sheet and fixed to wooden plugs with C.P brass screws and washers with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing C.P brass towel rail complete C.P brass brackets fixed to wooden plugs with C.P brass 600mmx20mm. (six hundred millimetre into twenty millimetre) Thick (Jaquar or ESS-ESS) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing chromium plated brass soap dish with C.P brass brackets fixed to wooden cleats with C.P brass screws . (Jaquar or ESS-ESS) with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) nominal bore C.P. brass flush pipe/spreaders for urinal with fittings such as unions, clamps etc. (all C.P.) including cutting holes and making good the same including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 32mm (thirty two millimetre) lead waste pipe for wash basin or sink including check nut including carriage of material with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing cowl IS marked including fixing with approved adhesive etc. including carriage of material with in all leads and lifts and as per the direction of Engineer-in-Charge. 75 mm (seventy five millimetre)

110 mm (one hundred ten millimetre)

Providing and fixing 15mm (fifteen millimetre) dia C.P brass bib tap with capstan head (Jaquar or ESS-ESS) with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) dia C.P brass pillar tap with capstan head (Jaquar or ESS-ESS) with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) C.P.Brass angle valve without nuts and pipe with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 300/450mm (three hundred/four hundred fifty millimetre) length 15mm (fifteen millimetre) nominal bore P.V.C connection pipe with brass unions with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing PTMT jet spray of approved quality and colour with 1metre tube with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 100 mm (hundred millimetre) nominal dia PTMT grating round of approved quality and colour with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 15 mm (fifteen millimetre) CP stop cock with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing Brass full way valve with in all leads and lifts and as per the direction of Engineer-in-Charge. 15 mm (fifteen millimetre)

20 mm (twenty millimetre)

Constructing manhole with R.C.C top slab in 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (twenty millimetre) nominal size) foundation concrete 1:4:8 (one cement : four sand : eight Graded stone aggregate 40mm (forty millimetre) nominal size ) inside plastering 15 mm (fifteen millimetre) thick with cement mortar 1:3(one cement : three sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (twenty millimetre) nominal size finished smooth complete including curing and testing (i)inside size 800mmx800mm (eight hundred millimetre into eight hundred millimetre) and 500 mm (five hundred millimetre) deep including C.I. cover with frame( light duty single (seal ) pattern I) 455mmx610mm (four hundred fifty five millimetre into six hundred ten millimetre) internal dimensions total weight of cover and frame to be not less than 38 kg (thirty eight kilogram) (weight of cover 23 kg (twenty three kilogram) and weight of frame 15 kg (fifteen kilogram) A)with 200 mm(two hundred millimetre) thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (one cement : three sand )with in all leads and lifts and as per the direction of Engineer-in-Charge.

rajesh kumar suman