Providing LWSS Kalchi Chiyali habitation in GP Tatiyana Tehsil Kamroo District Sirmour HP

Amount

Excavation in foundation and trenches etc.in earth work in all kinds of soil such as pick work ,jumper work decomposed conglomerate saturated soil soft and hard rock upto all leads lifts stacking the excavated soil not more than 3mtr.clear from the edge of excavation and then returning the stacked soil in 15cm layers when required in to plinth sides of foundation etc. consolidating each deposited layers by ramming and watering and then disposing of all surplus excavated earth as directed with in all leads lifts and as per directions of the Engineer-incharge

Providing and laying cement concrete 1:6:12(1cement:6sand:12 graded stone agg.40mm nominal size)and curing complete excluding the cost of form work in foundation & plinth including all leads lifts and carriage of material and as per the directions of Engineer-in-charge.

Providing and laying cement concrete 1:4:8(1cement:4sand:8 graded stone agg.40mm nominal size)and curing complete excluding the cost of form work in foundation & plinth including all leads lifts and carriage of material and as per the directions of Engineer-in-charge.

Providing and laying cement concrete work M 30 but not less than 1:1-1/2:3 (1cement:1-1/2 sand: 3 gradeds stone agg. 20mm nominal size & curing complete) excluding cost of form work and reinforcement for RCC work including all leads lifts complete and carriage of material etc. as per directions of Engineer incharge.

a) Foundation and plinth

b) Wall (any thickness but not less then 0.10thick) attached pillasters, buttress and the like.

c) In lintels beams. girders, bssumersand cantilivers upto floor two level including all leads lifts and as per the direction og the engineer in charge. depth including all leads lifts & carriage of material at site and as per direction of the Engineer-incharge.

Providing form work with steel sheets 3.15mm thick welded with angle iron 30x30x5 mm so as to give rough finish i/c centring shuttering structing and propping etc. with wooden bettens & Ballies, height or propping & centering below supporting floor to ceiling not exceeding 4 mtr.and removal of the same for insitu RCC work and PCC work.including all leads lifts and carriage of material at site & as per direction of Engineer incharge in:-

a)Flat surfaces such as sofits and suspended floors, roofs landing and the like floors etc. up to 200 mm in thickness.

b) Vertical surface such as wall (any thickness) Partions and the like i/c attached pillaster buttress plinth and the like.

Providing and laying cement concrete 1:2:4(1cement:2app.sand: 4 app. graded stone agg. 20mm nominal size )and curing complete excluding cost of form work & reinforcement for reinforced work in suspended floors, roofs landing shelves and their supports balconies, beams, girders bressumers and cantilivers upto to floor two level in all height and depth, including all leads lifts and carriage of material at site and as per direction of the Engineer-incharge.

Mild Steel/Tor steel reinforcement for RCC work including bending binding & placing in positing I/c all leads lifts and carriage of material and as per direction of the Engineer-in-charge. (L/Rate)

Providing and fixing Cast iron manhole cover of 455x610 mm size C.I.(medium)duty the weight of manhole cover not less than 23 kgs.including all leads lifts and carriage of materials as per direction of the Engineer-in-charge.

Fixing of Scour , inlet , outlet pipe G.I. Pipe 32mm dia including all leads lifts and carriage of material and as per direction of Engineer incharge.

Brick work using buiolding bricks in cement mortat 1:3 (1: cement 3:sand) complete in all leads lifts and as per the direction of the Engineer.

Providing placing in position in horizental layers filter media duly graded screened washed and cleared including all leads lifts and carriage of material upto site of work as as specified by Engineer incharge.

I)Top layer fine sand effective size 0.20mm to 40mm and

uniformity-co-fficient 2.00 to 3.00.

ii)IInd layer course sand 3mm to 6mm.

III) IIIrd layer Bajri 6mm to 20mm.

iv) Ivth layer Bajri 20mm to 25mm

v) Vthlayer bottom layer broken stone 50mm to 75mm dia.

Randam rubble masonry / polygonal rubble masonry ( uncoursed brought to course ) with hard stone of approved quality in in oundation and plinth levelling up with CC 1:6:12 in Cement Mortar 1:6(1cement:6sand) in all leads lifts and carriage etc. as per direction of Engineer inchrge.

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including racking out joints in cement mortar 1:6 ( 1 : cement :6 sand) including all leads lifts and as per the direction of the engineer in charge .

Providing and laying damp proof course 38mm thick with cement concrete 1:2:4 (1cement:2sand:4graded stone agg.12.5mm nominal size)and curing complete including all leads,lifts and carriage of material and as per direction of Engineer-in-charge.

Applying a coat of hot bitumen(maxphalt 80/100 or equivalent ) using 1.70kg per sqmt.on damp proof course after cleaning the surface in a piece of cloth lightly soaked with kerosene oil including all leads,lifts and carriage of material and as per directions of Engineer-in-charge.

2nd Class brick work using common building bricks in Super structure in Cement Mortar 1:6(1cement:6sand) in all leads lifts and carriage etc. as per direction of Engineer inchrge.

Providing fixing pressed steel door frames manufactured from commercial mild steel of1.25mm thickness including hinges,jump lock bud and if required angle threshold of M.S. angle 50x25mm or base tie of 1.25mm pressed steel I/c welding complete Including steel hinges 2.5mm thick with guard lock strick plate and apply a coat of approved steel primer affect pre-treaditional of surface in all leads lifts and carriage of materials as per

Profile-"B"

Prov.40x3mm flat iron hold fast 40cm long including fixing to frame with 10mm dia metre bolts,nuts and wooden plugs and embedding in cement concrete block 30x10x15cms 1:3:6 (1cement: 3sand: 6 graded stone agg.20mm nominal size)including all leads,lifts & carriage of material as per direction of the Engineer incharge.

Providing and fixing controlling arrangements with (25 to 32 )mm dia wheel valve i/c all type of tube fitting complete

Providing fixing M.S.grills of required pattern in wooden frames/pressed steel frame with M.S. flat surface round bars 12mm dia with round headed bolts and nuts or by screws .Plain grill including all leads lifts and carriage of material as per direction of Enginer incharge.

Providing and fixing 1 mm thick MS sheet door with frame of 40 mm x 40 mm x6 mm angle iron 3.13 mm MS guest plate at the juctions and corners. All necessary fitting complete including primery coat of red lead paint.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by throughly cleaning oil,grease,dirt and other foreign matter with ready mixed paint brushing with white lead for priming including all leads lifts and carriage of material as per direction of Engineer incharge.

Painting two coats (excluding priming coat) on new wood and wood based with surfaces with ready mixed paint other then white brushing to give an even shade including cleaning the surface of dirt dust and other foreign matter,sand papering and stopping. Including all leads lifts and carriage of material at site as per direction of Engineer incharge.

Bouldwer filling under floor hand packed tightly including all leads lifts and carriage pof materials at site and as per the direction of the Engineer in charge.

40mm thick cement concrete flooring 1:2:4 (1cement:2sand: 4 graded stone agg. 20mm nominal size)laid in one layer finished with a floating coat of neat cement including curing all leads, lifts and carriage of materials at site and as per direction of Engineer incharge

15 mm thick cement plaster in single coat of rough side of bricks/stone masonary for interior plastering upto floor two level including arrises internal rounded angles chamfers rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortor 1:6(1cement:6 sand) and curing complete including all leads lifts and carriage of materials at site as per direction of Engineer-incharge.

6 mm thick cement plaster in ceiling in Cement mortor 1:3 (1 cement:3 sand) including all leads lifts and carriage of material at site as per direction of Engineer incharge.

White washing with lime on undecorated wall surfaces (two coats) to give an even shade including throughly brooming the surface to remove all dirt dust mortor drops and loose scale of lime wash and other foreign matter including all leads lifts and carriage of material at site as per direction of Engineer-incharge.

Hiramchi colour wash on un decorated wall surface (Two coats) o give an even shade including throughly brooming the surface to remove of all dirt , dust & other foreign matter.

Providing under layer 75 mm thick unconsolidated bed dry brick/ stone (40 mm noinal sie) including finishinf the top surface. i/c all leads lifts and carriage of materials complete in all respect.

Providing plinth protection 50mm thick in cement concrete 1:3:6(1cement: 3sand: 6graded stone agg.20mm nominal size in all leads,lifts and carriage of material and as per direction of Engineer incharge.

Provd.& fixing Sliding door bolts anodized transparent or dyed to required colour or shade with necessary screws etc. complete including all leads lifts & carriage of material at site as per direction of Engineer incharge. 300x15mm

Providing and fixing tower bolts aluminium (barreled type) anodized transparent or dyed to required shade & colour screws complete including all leads, lifts and as per direction of Engineer incharge.

Provd.& fixing aluminium handles anodized transparent or dyed to required colour or shade with necessary screws etc. complete including all leads lifts & carriage of material at site as per direction of Engineer incharge.

Excavation in drains and channels etc. in earth work in all kinds of soil such as pick work,jumper work ,blasting work decomposed conglomerate saturated soil soft rock and hard rock including dressing of sides and beds and preparation of sub grade to level or slope including refilling the trenches and disposing of surplus earth upto all leads lifts disposed earth to be levelled and neatly dressed including jungle clearance and as per direction of Engineer-in-charge.

Laying, jointing of G.I. pipes of various dia in trenches (earth work in trenches to be measured and paid for seperately) including all leads lifts and carriage of material at site as per direction of Engineer-in-charge.

i)20mm dia (L)

i)25mm dia (L)

i)32mm dia (L)

i)50mm dia (L)

Steel work single section in built up section trusses and framed work, including cutting ,hoisting fixing in position and applying a priming coat of red lead paint, in gtratings framed, guards,bars,ladders, railing, brackets and simillar works including all leads and lifts and carriage of material as per direction of Engineer in charge

munshi ram

RAMESH CHAND SHARMA

CHATTER SINGH

Anil Sharma

Suneel Dutt

ATMA RAM